The ultrasonic wave velocities of Japanese cedar columns were measured using a non-contact method. An air-coupled ultrasonic wave was propagated through the axial and lateral directions of wood. The velocities in the ...The ultrasonic wave velocities of Japanese cedar columns were measured using a non-contact method. An air-coupled ultrasonic wave was propagated through the axial and lateral directions of wood. The velocities in the axial direction (V<sub>L</sub>) showed the minimum values around the pith. The averaged V<sub>L</sub> increased from 3600 m/s towards the outside of measurement area and attained the maximum values (=4010 m/s). The velocities in the lateral direction (V<sub>RT </sub>) showed no tendency among measurement points. The averaged V<sub>RT </sub> was 1450 m/s. The velocities obtained using the non-contact method showed a significant positive relationship with those obtained using the contact method. The averaged ratio of V<sub>L</sub> to V<sub>RT </sub> was measured to be approximately 2.2 to 2.8. These ratios were in agreement with those from a contact method. These findings suggest that it is possible to measure the velocity in Japanese cedar columns with the non-contact method by using air-coupled ultrasonics.展开更多
The working principle of the pipeline intelligent pig and the structure of ultrasonic probe array used to detect defects in oil/gas pipeline are introduced. The effects of the array＇ s radial position in pipe on defe...The working principle of the pipeline intelligent pig and the structure of ultrasonic probe array used to detect defects in oil/gas pipeline are introduced. The effects of the array＇ s radial position in pipe on defect resolution are analyzed. The causes leading to radial positioning error are investigated. An algo- rithm for the radial self-positioning is presented. The experimental results show that the radial self-positioning algorithm can eliminate the array＇ s space position error effectively and improve the defect resolution.展开更多
Because the UT （ultrasonic testing） flexible probe technology may be an appropriate answer to examine components with uneven surface, AREVA has developed an industrial application of the CEA＇s （French Atomic Energ...Because the UT （ultrasonic testing） flexible probe technology may be an appropriate answer to examine components with uneven surface, AREVA has developed an industrial application of the CEA＇s （French Atomic Energy and Alternative Energies） flexible phased arrays sensors. As a ＂first of a kind＂ project, the challenges faced were significant, including developing a phased array smart probe suitable for industrial use on rather simple but large scale geometries, permitting UT propagation within a constraining media structure and then targeting a qualification according to ENIQ （European Network for Inspection Qualification） methodology. A prototype flexible probe, designed for UT validation, and final flexible linear array probes permitting the UT behavior （as, e.g., detection and sizing from diffraction type echoes） to be maintained on wavy coupling surfaces, have been manufactured. These probes include a profilemeter with optical sensors control and a specifically designed coupling circuit （avoiding probe housing tightness issues）. Qualification has been performed using open test blocks, （where known ＂defects＂ exist, for procedure qualification）, and blind test blocks, （where ＂defects＂ are unknown, for qualification of testing personnel）. One open test bloc was customized to represent a ＂real＂ surface condition, with gaps up to 2.5 mm under the regular rigid probes. AREVAI/BGSI in Germany was selected to lead the project, with assistance in development and manufacturing sub-contracted to ＂CEA/LIST＂ laboratory, and the companies ＂IMASONIC＂ and ＂M2M＂. This paper describes the development of these probes and explains a few features （ENIQ qualification objectives fulfilled, UT data acquired on actual perturbed surface） that made their industrial implementation successful.展开更多
A manual inspection of large-diameter tubular joints is difficult. As a result a scanner with three degrees of freedom （ DOFs） was developed based on the scanning principle of ultrasonic phased array. The weld traci...A manual inspection of large-diameter tubular joints is difficult. As a result a scanner with three degrees of freedom （ DOFs） was developed based on the scanning principle of ultrasonic phased array. The weld tracing is realized by a 2DOF motion of scanner. The pose of ultrasonic probe is controlled by the third one. The control strategy is put forward based on a programmable multi-axis controller. Four kinds of scanning modes can be implemented simultaneously employing this ultrasonic inspection system. Experiments on reference blocks of tubular joints reveal that the automatic ultrasonic phased array inspection system has the same inspection accuracy as a manual ultrasonic inspection. This system is superior to the manual ultrasonic system in terms of reliability and repeatability. The artificial dejects of weld at tubular joint can be detected accurately with the presented inspection system.展开更多
Air-coupled ultrasonic transducers are used to generate and receive Lamb waves in quasi-isotropic laminated composite beams for delamination detection. The influence of incident angle on the excited mode is studied. N...Air-coupled ultrasonic transducers are used to generate and receive Lamb waves in quasi-isotropic laminated composite beams for delamination detection. The influence of incident angle on the excited mode is studied. Numerical calculation and experimental results show that a pure Lamb wave mode can be generated if the transmitting transducer is oriented at a specific angle, and the receiving transducer can either be oriented to detect the same mode as that generated by the transmitter or to detect another mode generated by mode conversion at a defect. A three-dimensional finite element model is created to predict the interaction of Lamb waves with delamination, and some unique mechanisms of interaction between A0 mode Lamb waves and delamination are revealed in detail. The experimental results obtained on laminated composite beam using air-coupled ultrasonic transducers are well in accordance with finite element simulation results. Research results show that air-coupled ultrasonic guided waves can be used for delamination damage detection effectively in laminated composite beams.展开更多
文摘The ultrasonic wave velocities of Japanese cedar columns were measured using a non-contact method. An air-coupled ultrasonic wave was propagated through the axial and lateral directions of wood. The velocities in the axial direction (V<sub>L</sub>) showed the minimum values around the pith. The averaged V<sub>L</sub> increased from 3600 m/s towards the outside of measurement area and attained the maximum values (=4010 m/s). The velocities in the lateral direction (V<sub>RT </sub>) showed no tendency among measurement points. The averaged V<sub>RT </sub> was 1450 m/s. The velocities obtained using the non-contact method showed a significant positive relationship with those obtained using the contact method. The averaged ratio of V<sub>L</sub> to V<sub>RT </sub> was measured to be approximately 2.2 to 2.8. These ratios were in agreement with those from a contact method. These findings suggest that it is possible to measure the velocity in Japanese cedar columns with the non-contact method by using air-coupled ultrasonics.
文摘The working principle of the pipeline intelligent pig and the structure of ultrasonic probe array used to detect defects in oil/gas pipeline are introduced. The effects of the array＇ s radial position in pipe on defect resolution are analyzed. The causes leading to radial positioning error are investigated. An algo- rithm for the radial self-positioning is presented. The experimental results show that the radial self-positioning algorithm can eliminate the array＇ s space position error effectively and improve the defect resolution.
文摘Because the UT （ultrasonic testing） flexible probe technology may be an appropriate answer to examine components with uneven surface, AREVA has developed an industrial application of the CEA＇s （French Atomic Energy and Alternative Energies） flexible phased arrays sensors. As a ＂first of a kind＂ project, the challenges faced were significant, including developing a phased array smart probe suitable for industrial use on rather simple but large scale geometries, permitting UT propagation within a constraining media structure and then targeting a qualification according to ENIQ （European Network for Inspection Qualification） methodology. A prototype flexible probe, designed for UT validation, and final flexible linear array probes permitting the UT behavior （as, e.g., detection and sizing from diffraction type echoes） to be maintained on wavy coupling surfaces, have been manufactured. These probes include a profilemeter with optical sensors control and a specifically designed coupling circuit （avoiding probe housing tightness issues）. Qualification has been performed using open test blocks, （where known ＂defects＂ exist, for procedure qualification）, and blind test blocks, （where ＂defects＂ are unknown, for qualification of testing personnel）. One open test bloc was customized to represent a ＂real＂ surface condition, with gaps up to 2.5 mm under the regular rigid probes. AREVAI/BGSI in Germany was selected to lead the project, with assistance in development and manufacturing sub-contracted to ＂CEA/LIST＂ laboratory, and the companies ＂IMASONIC＂ and ＂M2M＂. This paper describes the development of these probes and explains a few features （ENIQ qualification objectives fulfilled, UT data acquired on actual perturbed surface） that made their industrial implementation successful.
文摘A manual inspection of large-diameter tubular joints is difficult. As a result a scanner with three degrees of freedom （ DOFs） was developed based on the scanning principle of ultrasonic phased array. The weld tracing is realized by a 2DOF motion of scanner. The pose of ultrasonic probe is controlled by the third one. The control strategy is put forward based on a programmable multi-axis controller. Four kinds of scanning modes can be implemented simultaneously employing this ultrasonic inspection system. Experiments on reference blocks of tubular joints reveal that the automatic ultrasonic phased array inspection system has the same inspection accuracy as a manual ultrasonic inspection. This system is superior to the manual ultrasonic system in terms of reliability and repeatability. The artificial dejects of weld at tubular joint can be detected accurately with the presented inspection system.
基金supported by the National Natural Science Foundation of China(Grant Nos. 11272021 and 50975006)Beijing Natural Science Foundation(Grant No. 1122007)+1 种基金the Importation and Development of High-Caliber Talents Project of Beijing Municipal Institutions(No.CIT&TCD201304048)Beijing Nova Program(Grant No. 2008A015)
文摘Air-coupled ultrasonic transducers are used to generate and receive Lamb waves in quasi-isotropic laminated composite beams for delamination detection. The influence of incident angle on the excited mode is studied. Numerical calculation and experimental results show that a pure Lamb wave mode can be generated if the transmitting transducer is oriented at a specific angle, and the receiving transducer can either be oriented to detect the same mode as that generated by the transmitter or to detect another mode generated by mode conversion at a defect. A three-dimensional finite element model is created to predict the interaction of Lamb waves with delamination, and some unique mechanisms of interaction between A0 mode Lamb waves and delamination are revealed in detail. The experimental results obtained on laminated composite beam using air-coupled ultrasonic transducers are well in accordance with finite element simulation results. Research results show that air-coupled ultrasonic guided waves can be used for delamination damage detection effectively in laminated composite beams.
