This study examines the impact of variations in side-blowing airflow velocity on plasma generation,combustion wave propagation mechanisms,and surface damage in fused silica induced by a combined millisecond-nanosecond...This study examines the impact of variations in side-blowing airflow velocity on plasma generation,combustion wave propagation mechanisms,and surface damage in fused silica induced by a combined millisecond-nanosecond pulsed laser.The airflow rate and pulse delay are the main experimental variables.The evolution of plasma motion was recorded using ultrafast time-resolved optical shadowing.The experimental results demonstrate that the expansion velocities of the plasma and combustion wave are influenced differently by the sideblowing airflow at different airflow rates(0.2 Ma,0.4 Ma,and 0.6 Ma).As the flow rate of the sideblow air stream increases,the initial expansion velocities of the plasma and combustion wave gradually decrease,and the side-blow air stream increasingly suppresses the plasma.It is important to note that the target vapor is always formed and ionized into plasma during the combined pulse laser action.Therefore,the side-blown airflow alone cannot completely clear the plasma.Depending on the delay conditions,the pressure of the side-blowing airflow,the influence of inverse Bremsstrahlung radiation absorption and target surface absorption mechanisms can lead to a phenomenon known as the double combustion waves when using a nanosecond pulse laser.Both simulation and experimental results are consistent,indicating the potential for further exploration of fused silica targets in the laser field.展开更多
TiB2 powders coated with BN were prepared by Hybridization System making use of dry impact blending method to achieve powder surface modification. Parameters of coating were analyzed and the most appropriate condition...TiB2 powders coated with BN were prepared by Hybridization System making use of dry impact blending method to achieve powder surface modification. Parameters of coating were analyzed and the most appropriate condition was summarized. Scan electron microscope of JSM-5610LV and transmission electron microscope of H-600STEM/EDS were used to observe the microstructure of coated powders. Results show that treatment time, rotation speed, granularity ratio of TiB2 to BN, pretreatment of materials etc influence the coating results evidently. Mixing raw materials and coating with BN under the appropriate condition can get round TiB2/BN composite powder with smooth surface and compact coating layer.展开更多
基金funded by the International Science and Technology Cooperation Project of Jilin Provincial Department of Science and Technology(No.20230402078GH)。
文摘This study examines the impact of variations in side-blowing airflow velocity on plasma generation,combustion wave propagation mechanisms,and surface damage in fused silica induced by a combined millisecond-nanosecond pulsed laser.The airflow rate and pulse delay are the main experimental variables.The evolution of plasma motion was recorded using ultrafast time-resolved optical shadowing.The experimental results demonstrate that the expansion velocities of the plasma and combustion wave are influenced differently by the sideblowing airflow at different airflow rates(0.2 Ma,0.4 Ma,and 0.6 Ma).As the flow rate of the sideblow air stream increases,the initial expansion velocities of the plasma and combustion wave gradually decrease,and the side-blow air stream increasingly suppresses the plasma.It is important to note that the target vapor is always formed and ionized into plasma during the combined pulse laser action.Therefore,the side-blown airflow alone cannot completely clear the plasma.Depending on the delay conditions,the pressure of the side-blowing airflow,the influence of inverse Bremsstrahlung radiation absorption and target surface absorption mechanisms can lead to a phenomenon known as the double combustion waves when using a nanosecond pulse laser.Both simulation and experimental results are consistent,indicating the potential for further exploration of fused silica targets in the laser field.
基金Project(50372047) supported by the National Natural Science Foundation of China
文摘TiB2 powders coated with BN were prepared by Hybridization System making use of dry impact blending method to achieve powder surface modification. Parameters of coating were analyzed and the most appropriate condition was summarized. Scan electron microscope of JSM-5610LV and transmission electron microscope of H-600STEM/EDS were used to observe the microstructure of coated powders. Results show that treatment time, rotation speed, granularity ratio of TiB2 to BN, pretreatment of materials etc influence the coating results evidently. Mixing raw materials and coating with BN under the appropriate condition can get round TiB2/BN composite powder with smooth surface and compact coating layer.
