Computational prediction of stall aerodynamics in free air and in close proximity to the ground considering the 30P30N three-element high-lift configuration is carried out based on CFD simulations using the OpenFOAM c...Computational prediction of stall aerodynamics in free air and in close proximity to the ground considering the 30P30N three-element high-lift configuration is carried out based on CFD simulations using the OpenFOAM code and Fluent software. Both the attached and separated flow regimes are simulated using the Reynolds Averaged Navier-Stokes (RANS) equations closed with the Spalart-Allamaras (SA) turbulence model for static conditions and pitch oscillations at Reynolds number, <em>Re</em> = 5 x 10<sup>6</sup> and Mach number, <em>M</em> = 0.2. The effects of closeness to the ground and dynamic stall are investigated and the reduction in the lift force in close proximity to the ground is discussed.展开更多
The effect of the turbulence intensity of the oncoming stream on the aerodynamic characteristics of the NACA-0012 airfoil is investigated by a direct numerical simulation. The numerical results are found to be consist...The effect of the turbulence intensity of the oncoming stream on the aerodynamic characteristics of the NACA-0012 airfoil is investigated by a direct numerical simulation. The numerical results are found to be consistent with the experimental measurements. Based on the finite spectral QUICK scheme, the simulation gets the high accuracy results. Both the simulation and the experiment reveal that the airfoil stall does not exist for the low turbulence intensity, however, occurs when the turbulence intensity increases sufficiently. Besides, the turbulence intensity has a significant effect on both the airfoil boundary layer and the separated shear layer.展开更多
Flow separation is typically an undesirable phenomenon, and boundary layer control is an important technique for the separation problems on airfoils. The synthetic jet actuator is considered as a promising candidate f...Flow separation is typically an undesirable phenomenon, and boundary layer control is an important technique for the separation problems on airfoils. The synthetic jet actuator is considered as a promising candidate for flow control applications because of its compact nature and ability to generate momentum without the need for fluidic plumbing. In the present study, an active separation control system using synthetic jets is proposed and practically applied to the stall control of the NACA0012 airfoil in a wind tunnel test. In our proposed system, the flow conditions (stalled or unstalled) can be judged by calculating from two static pressure holes on the airfoil upper surface alone. The experimental results indicate that the maximum lift coefficient increases by 11% and the stall angle rises by 4°in contrast to the case under no control. It is confirmed that our proposed system can suppress the stall on the NACA0012 airfoil and that the aerodynamic performance of the airfoil can be enhanced. The proposed system can also be operated prior to the onset of stall. Therefore, separation control is always attained with no stall for all flow fields produced by changing the angle of attack that were examined.展开更多
In the past extensive research has been carried out, to study the effect of Gurney flap (GF) on symmetric and cambered airfoil for its usage in low Reynolds number regime. Use of GF at the trailing edge of the airfoil...In the past extensive research has been carried out, to study the effect of Gurney flap (GF) on symmetric and cambered airfoil for its usage in low Reynolds number regime. Use of GF at the trailing edge of the airfoil enhances the lift due to increase in the effective camber of the airfoil, which in turn improves the aerodynamic efficiency i.e. Cl/Cd. In the present study, Eppler 423 airfoil is used to first understand the aerodynamics of such a highly cambered airfoil and later GF of various sizes were added on it to understand the change in flow dynamics achieved by adding the GF and their impact on aerodynamic parameters such as Cl, Cd and Cl/Cd. Eppler 423 being a highly cambered airfoil produces high lift coefficient and smoother stall and by adding the GF of various sizes the performance of Eppler 423 improves tremendously and reason for this enhanced performance and effect of size of GF are presented in this paper. Vortex Generators (VG) generate counter rotating vortices that allow the flow to remain attached even at high angles of attack. Also, effect of adding VG at the leading edge of Eppler 423 aerofoil is presented in this paper. At last, results obtained from combination of VG at leading edge and GF at trailing edge on Eppler 423 aerofoil are discussed at length.展开更多
文摘Computational prediction of stall aerodynamics in free air and in close proximity to the ground considering the 30P30N three-element high-lift configuration is carried out based on CFD simulations using the OpenFOAM code and Fluent software. Both the attached and separated flow regimes are simulated using the Reynolds Averaged Navier-Stokes (RANS) equations closed with the Spalart-Allamaras (SA) turbulence model for static conditions and pitch oscillations at Reynolds number, <em>Re</em> = 5 x 10<sup>6</sup> and Mach number, <em>M</em> = 0.2. The effects of closeness to the ground and dynamic stall are investigated and the reduction in the lift force in close proximity to the ground is discussed.
基金Project supported by the National Natural Science Foundation of China(No.108720006)the National Basic Research Program of China(973 Program)(No.2007CB714601)
文摘The effect of the turbulence intensity of the oncoming stream on the aerodynamic characteristics of the NACA-0012 airfoil is investigated by a direct numerical simulation. The numerical results are found to be consistent with the experimental measurements. Based on the finite spectral QUICK scheme, the simulation gets the high accuracy results. Both the simulation and the experiment reveal that the airfoil stall does not exist for the low turbulence intensity, however, occurs when the turbulence intensity increases sufficiently. Besides, the turbulence intensity has a significant effect on both the airfoil boundary layer and the separated shear layer.
文摘Flow separation is typically an undesirable phenomenon, and boundary layer control is an important technique for the separation problems on airfoils. The synthetic jet actuator is considered as a promising candidate for flow control applications because of its compact nature and ability to generate momentum without the need for fluidic plumbing. In the present study, an active separation control system using synthetic jets is proposed and practically applied to the stall control of the NACA0012 airfoil in a wind tunnel test. In our proposed system, the flow conditions (stalled or unstalled) can be judged by calculating from two static pressure holes on the airfoil upper surface alone. The experimental results indicate that the maximum lift coefficient increases by 11% and the stall angle rises by 4°in contrast to the case under no control. It is confirmed that our proposed system can suppress the stall on the NACA0012 airfoil and that the aerodynamic performance of the airfoil can be enhanced. The proposed system can also be operated prior to the onset of stall. Therefore, separation control is always attained with no stall for all flow fields produced by changing the angle of attack that were examined.
文摘In the past extensive research has been carried out, to study the effect of Gurney flap (GF) on symmetric and cambered airfoil for its usage in low Reynolds number regime. Use of GF at the trailing edge of the airfoil enhances the lift due to increase in the effective camber of the airfoil, which in turn improves the aerodynamic efficiency i.e. Cl/Cd. In the present study, Eppler 423 airfoil is used to first understand the aerodynamics of such a highly cambered airfoil and later GF of various sizes were added on it to understand the change in flow dynamics achieved by adding the GF and their impact on aerodynamic parameters such as Cl, Cd and Cl/Cd. Eppler 423 being a highly cambered airfoil produces high lift coefficient and smoother stall and by adding the GF of various sizes the performance of Eppler 423 improves tremendously and reason for this enhanced performance and effect of size of GF are presented in this paper. Vortex Generators (VG) generate counter rotating vortices that allow the flow to remain attached even at high angles of attack. Also, effect of adding VG at the leading edge of Eppler 423 aerofoil is presented in this paper. At last, results obtained from combination of VG at leading edge and GF at trailing edge on Eppler 423 aerofoil are discussed at length.
