Hydration Characteristics and Microstructure of Alkali-Activated Slag Concrete: A Review

Alkali-activated slag concrete (AASC) is a new green building material. The amount of CO_(2) produced by AASC is 1/5th of that produced by ordinary Portland cement concrete (OPCC). In addition, AASC promotes the reuse of slag and other wastes and saves resources. Furthermore, the scope of use of slag has been expanded. The progress of the research on the hydration characteristics, microstructure, interfacial transition zone, and pore structure of AASC based on the relevant literatures was analyzed and summarized in this study. The influences of the slag composition, the type and dosage of the alkali activator, and the curing conditions on the hydration characteristics and the microstructure of the AASC were discussed. Relatively few research results on the microstructure of AASC are available, and the relevant conclusions are not completely consistent. Moreover, there are many constraints on the development of AASC (e.g., complex composition of raw materials of slag, large shrinkage deformation, and low fluidity). Therefore, further research is required.

On the Preparation of Low-Temperature-Rise and Low-Shrinkage Concrete Based on Phosphorus Slag

The effects of different contents of a MgO expansive agent and phosphorus slag on the mechanical properties,shrinkage behavior,and the heat of hydration of concrete were studied.The slump flow,setting time,dry shrinkage,and hydration heat were used as sensitive parameters to assess the response of the considered specimens.As shown by the results,in general,with an increase in the phosphorus slag content,the hydration heat of concrete decreases for all ages,but the early strength displays a downward trend and the dry shrinkage rate increases.The 90-d strength and dry shrinkage of concrete could be improved with a phosphorus residue content between 0%-20%,with the best performances in terms of mechanical properties and shrinkage characteristics being achieved for a content of 20 kg/m^(3).On the basis of these results,it can be concluded that appropriate amounts of phosphorus slag and MgO expansive agent can be used to improve the compressive strength of concrete in the later stage by reducing the hydration heat and dry shrinkage rate,respectively.

Tests on Alkali-Activated Slag Foamed Concrete with Various Water-Binder Ratios and Substitution Levels of Fly Ash

To provide basic data for the reasonable mixing design of the alkali-activated (AA) foamed concrete as a thermal insulation material for a floor heating system, 9 concrete mixes with a targeted dry density less than 400 kg/m3 were tested. Ground granulated blast-furnace slag (GGBS) as a source material was activated by the following two types of alkali activators: 10% Ca(OH)2 and 4% Mg(NO3)2, and 2.5% Ca(OH)2 and 6.5% Na2SiO3. The main test parameters were water-to-binder (W/B) ratio and the substitution level (RFA) of fly ash (FA) for GGBS. Test results revealed that the dry density of AA GGBS foamed concrete was independent of the W/B ratio an RFA, whereas the compressive strength increased with the decrease in W/B ratio and with the increase in RFA up to 15%, beyond which it decreased. With the increase in the W/B ratio, the amount of macro capillaries and artificial air pores increased, which resulted in the decrease of compressive strength. The magnitude of the environmental loads of the AA GGBS foamed concrete is independent of the W/B ratio and RFA. The largest reduction percentage was found in the photochemical oxidation potential, being more than 99%. The reduction percentage was 87% - 93% for the global warming potential, 81% - 84% for abiotic depletion, 79% - 84% for acidification potential, 77% - 85% for eutrophication potential, and 73% - 83% for human toxicity potential. Ultimately, this study proved that the developed AA GGBS foamed concrete has a considerable promise as a sustainable construction material for nonstructural element.

A machine learning model to predict unconfined compressive strength of alkali-activated slag-based cemented paste backfill

The unconfined compressive strength(UCS)of alkali-activated slag(AAS)-based cemented paste backfill(CPB)is influenced by multiple design parameters.However,the experimental methods are limited to understanding the relationships between a single design parameter and the UCS,independently of each other.Although machine learning(ML)methods have proven efficient in understanding relationships between multiple parameters and the UCS of ordinary Portland cement(OPC)-based CPB,there is a lack of ML research on AAS-based CPB.In this study,two ensemble ML methods,comprising gradient boosting regression(GBR)and random forest(RF),were built on a dataset collected from literature alongside two other single ML methods,support vector regression(SVR)and artificial neural network(ANN).The results revealed that the ensemble learning methods outperformed the single learning methods in predicting the UCS of AAS-based CPB.Relative importance analysis based on the bestperforming model(GBR)indicated that curing time and water-to-binder ratio were the most critical input parameters in the model.Finally,the GBR model with the highest accuracy was proposed for the UCS predictions of AAS-based CPB.

Efficient Use of Steel Slag in Alkali-Activated Blast Furnace Slag Based Geopolymer

Energy shortage and the emission of greenhouse gases have become a global problem of urgent concern.Therefore,there is an urgent need to develop a low carbon building material.Geopolymers have become a hot topic due to their environmental sustainability and the feasibility of immobilizing industrial waste.In this paper,steel slag(SS)fines were investigated as auxiliary materials of blast furnace slag(BFS)based geopolymer.The hydration heat properties,flowability,compressive strength,sorptivity coefficient,X-ray diffraction(XRD),and scanning electron microscopy(SEM)of the geopolymer pastes were determined.The results showed that the incorporation of SS weakened the reactivity of the BFS-based geopolymer paste and improved the flow values of the paste.The compressive strength of the geopolymer with 20%SS content reached 117 MPa at 28 d.The geopolymer specimens with high compressive strength showed a low sorptivity coefficient.The microscopic results showed that the addition of the appropriate amount of SS reduced the cracks,improved the density of the geopolymer,and produced a geopolymer composite with excellent mechanical properties.

Effect of Recycled Aggregate and Slag as Substitutes for Natural Aggregate and Cement on the Properties of Concrete:A Review

Using recycled aggregate(RA)and slag instead of natural aggregate(NA)and cement can reduce greenhouse gas emissions(GHGE)and achieve effective waste recovery.In recent years,RA has been widely used to replace NA in concrete.Every year,several researchers conduct investigations on the mechanical performance and durability of recycled aggregate concrete(RAC).Due to the loose and porous material properties of RA,the mechanical properties and durability of RAC,such as strength,carbonation resistance,permeability resistance and chloride ion penetration resistance,are greatly reduced compared with natural aggregate concrete.In contrast,concrete containing slag instead of NA and cement generally improved the strength of concrete and reduced the internal porosity of materials.Herein,we discuss the effects of RA and slag on the workability,compressive strength,splitting tensile strength,ultrasonic pulse velocity(UPV)value,and elastic modulus of concrete.The relationships between the compressive strength and the splitting tensile strength,UPV value,and elastic modulus are discussed,and the optimal substitution method is proposed.In addition,various equations for calculating the compressive strength of concrete based on performance factors related to the compressive strength are summarized.

Properties of Sustainable High Strength Concrete with Waste Copper Slag

The present work investigates copper slag as a substitute for river sand in high-strength concrete.The concrete mixtures were manufactured with 10%,30%,50%,70%,and 100%of copper slag to evaluate the mechanical and durability properties.The experimental results indicate that replacing copper slag above 50%affects the performance characteristics of the concrete due to its high angularity and lower water absorption characteristics.The strength of concrete with 50%copper slag is improved by 5.6%,whereas the strength of concrete with 100%copper slag is reduced by 2.75%at 28 days.However,increased curing to 90days improves the strength of the former by 7.16%and reduces the latter by only 0.23%.The water absorption,porosity,and rapid chloride penetration of the concrete mixtures with 100%copper slag are increased by 10.44%,13.20%,and 19.56%compared to control concrete.Micro-structural investigations through SEM infer higher replacement of copper results in higher void formation due to its reduced water absorption.

Workability and Strength of Ceramsite Self-Compacting Concrete with Steel Slag Sand

This study focuses on the workability and compressive strength of ceramsite self-compacting concrete with fine aggregate partially substituted by steel slag sand(CSLSCC)to prevent the pollution of steel slag in the environment.The SF,J-ring,visual stability index,and sieve analysis tests are primarily employed in this research to investigate the workability of freshly mixed self-compacting concrete containing steel slag at various steel slag sand replacement rates.The experiment results indicate that CSLSCC with the 20%volume percentage of steel slag(VPS)performs better workability,higher strength,and higher specific strength.The 7-day compressive strength of CSLSCC with the 0.4 of the water-binder ratio(W/B),decreases with the increase of steel slag content,while the 28-day compressive strength increases significantly.The ceramsite self-compacting concrete with good comprehensive performance can be obtained when the substitution rate of steel slag sand for fine aggregate is less than 20%(volume percentage).

Synthesis and Microstructure Analysis of Autoclaved Aerated Concrete with Carbide Slag Addition

Synthesis of autoclaved aerated concrete （AAC） has been carried out with carbide slag addition, and the carbide slag could be used as a main material to produce the AAC with the compressive strength about 2 MPa and the density below 0.6 g.cm-3. In this study, quartz sand acted as frame structure phase in the matrix, and quartz addition also influenced the Si/Ca of starting material. Tobermorite and CSH gel were formed readily at 62%, which seemed to enhance the compressive strength of samples. Curing time seemed to affect the morphology of phase produced, and specimen with the plate-like tobermorite formed at 10 h appeared to have a better compressive strength development than the fiber-like one at 18 h. The higher curing temperature seemed to favor the tobermorite and CSH gel formation, which also exerted a significant effect on the strength development of the samples. On the micro-scale, the formed CSH gel was filled in the interface of the matrix, and the tobermorite appeared to grow in internal-surface of the pores and interstices. The tobermorite or/and CSH formation seemed to densify the matrix, and therefore enhanced the strength of the samples.

Preparation of Reactive Powder Concrete Using Fly Ash and Steel Slag Powder

To decrease the cement and SF content of RPC by using ultra-fine fly ash （UFFA） and steel slag powder （SS）, the effect of these mineral admixtures on compressive strength of RPC were investigated. The experimental results indicate that the utilization of UFFA and SS in RPC is feasible and has prominent mechanical performance. The microstructure analysis （SEM and TG-DTG-DSC） demonstrated that the excellent mechanical properties of RPC containing SS and UFFA were mainly attributed to the sequential hydration filling effect of the compound system.

Research on the resource utilization of Baosteel steel slag as concrete material

The utilization of steel slag has been a worldwide issue for a long time. Attention is increasingly being paid to the technological innovation and development of steel slag. Aiming at the development of environmentally friendly steel slag concrete materials and their use in a recyclable economy ,Baosteel has recently been conducting research on and using many new building materials, including steel slag powder concrete, steel slag pervious concrete, steel slag counter weight concrete and so on. In this way, steel slag has been turned from a kind of solid waste into a value-added material. The technology of steel slag utilization has been enriched and developed,while a new model of using Baosteel steel slag in a recyclable economy has also been explored and practised.

Clayey soil stabilization using alkali-activated volcanic ash and slag

Lime and Portland cement are the most widely used binders in soil stabilization projects.However,due to the high carbon emission in cement production,research on soil stabilization by the use of more environmentally-friendly binders with lower carbon footprint has attracted much attention in recent years.This research investigated the potential of using alkali-activated ground granulated blast furnace slag(GGBS)and volcanic ash(VA)as green binders in clayey soil stabilization projects,which has not been studied before.The effects of different combinations of VA with GGBS,various liquid/solid ratios,different curing conditions,and different curing periods(i.e.7 d,28 d and 90 d)were investigated.Compressive strength and durability of specimens against wet-dry and freeze-thaw cycles were then studied through the use of mechanical and microstructural tests.The results demonstrated that the coexistence of GGBS and VA in geopolymerization process was more effective due to the synergic formation of N-A-S-H and C-(A)-S-H gels.Moreover,although VA needs heat curing to become activated and develop strength,its partial replacement with GGBS made the binder suitable for application at ambient temperature and resulted in a remarkably superior resistance against wet-dry and freeze-thaw cycles.The carbon embodied of the mixtures was also evaluated,and the results confirmed the low carbon footprints of the alkali-activated mixtures.Finally,it was concluded that the alkali-activated GGBS/VA could be promisingly used in clayey soil stabilization projects instead of conventional binders.

Pitting corrosion resistance of a novel duplex alloy steel in alkali-activated slag extract in the presence of chloride ions

In this study, two types of reinforcing steels(conventional low-carbon steel and a novel duplex alloy steel with Cr and Mo) were exposed to chloride-contaminated extract solutions(ordinary Portland cement(OPC) extract and alkali-activated slag(AAS) extract) to investigate their pitting corrosion resistance. The results confirm that the pitting corrosion resistance of the alloy steel is much higher than that of the low-carbon steel in both extract solutions with various Na Cl concentrations. Moreover, for each type of steel, the AAS extract contributes to a higher pitting corrosion resistance compared with the OPC extract in the presence of chloride ions, likely because of the formation of flocculent precipitates on the steel surface.

Test and analysis of influencing factors on the permeability coefficient of steel slag permeable concrete

The steel slag （SS） permeable concrete was prepared by SS. The influences of the aggregate-cement rate, the aggregate particle size, the water-cement rate, the admixture dosage and other factors on the permeability coefficient of SS permeable concrete were analyzed. The law of influence was also investigated. The study serves as a technological reference for the construction and design of SS permeable concrete.

Influence of Thermally Treated Flue Gas Desulfurization(FGD) Gypsum on Performance of the Slag Powder Concrete

The feasibility of flue gas desulphurization （FGD） as concrete admixture was studied. A combined concrete admixture of the thermally-treated FGD gypsum and slag powder was explored. The FGD gypsum was roasted at 200℃ for 60 min and then mixed with the slag powder to form FGD gypsum-slag powder combined admixture in which the SO3 content was 3.5wt%. Cement was partially and equivalently replaced by slag powder alone or FGD gypsum-slag powder, at concentration of 25wt%, 40wt%, and 50wt%, respectively. The setting times, hydration products, total porosity and pore size distributions of the paste were determined. The compressive strength and drying shrinkage of cement mortar and concrete were also tested. The experimental results show that, in the presence of FGD gypsum, the setting times are much slower than those of pastes in the absence of FGD gypsum. The combination of FGD gypsum and slag powder provides synergistic benefits above that of slag powder alone. The addition of FGD gypsum provides benefit by promoting ettringite formation and forms a compact microstructure, increasing the compressive strength and reduces the drying shrinkage of cement mortar and concrete.

Effect of magnesia on properties and microstructure of alkali-activated slag cement

The effect of magnesia bumt at 800-950℃ on the properties, especially the shrinkage, of alkali-activated slag cement （AASC.） was experimentally studied. Experimental results show that, although adding 4%-8% lightly-burnt magnesia may shorten the setting time and slightly reduce the compressive strength of AASC, it c, an remarkably reduce the shrinkage of AASC. The results also show that the setting time of AASC with a certain amount of magnesia increases with the buming temperature, and that the flexural and compressive strengths of AASC decrease with the increase of the additive amount of magnesia. Generally, the adverse effect of magnesia decreases with the increase of the burning temperature：, and the shrinkage-reducing effect of magnesia increases with the additive amount of magnesia. X-ray diffraction （XRD） and scanning electron microscopy （SEM） analyses show that some magnesia particles in the hardened AASC paste at a 28-d age remained unhydrated, and that the compactness decreased a little as magnesia was added. We can also conclude that magnesia bumt at 850-950℃ can be used to reduce the shrinkage of AASC only when its additive amount does not exceed 8%; otherwise, the setting time may be too short, and the flexural and compressive strengths may severely decrease.

Experimental Research of Concrete with Steel Slag Powder and Zeolite Powder

In order to increase use ratio of steel slag solid waste,the concrete containing steel slag powder and zeolite powder as admixtures was prepared by using the orthogonal test method.The effects of water-binder ratio,sand ratio,steel slag powder content and zeolite powder on working properties,mechanical strength and chloride ion permeability of the concrete was studied.It was found that the early strength of the concrete had a decrease with the mixing of steel slag and zeolite powders,but its later strength approached to pure concrete.Moreover,the physical filling and pozzolanic activity of the admixtures increased the density of the concrete,resulting in the improvement of the durability of the concrete by the migration speed of Cl−reducing.The optimum mix ratio of C40 steel slag powder-zeolite powder concrete is obtained,and which had the slump of 220 mm,the 3 d,7 d and 28 d compressive strengths of 27.8 MPa,37.5 MPa and 48.4 MPa,the 6 h electric flux of 950 C and the diffusion coefficient of 1.65×10−12 m2/s.

Combined Recycling of White Rice Husk Ash as Cement Replacement and Metal Furnace Slag as Coarse-Aggregate Replacement to Produce Self-Consolidating Concrete

According to empirical evidence,high levels of energy and considerable amounts of natural resources are used in the production of concrete.Given the context,this study explores self-consolidating concrete(SCC)that includes rice husk ash(RHA)and metal furnace slag(MFS)as an alternative to cement and the natural aggregates in standard SCC mixes.In this study,mixture designs are investigated with 20 wt.%of RHA,10–30 wt.%of MFS and water-to-powder material ratios of 0.30 and 0.40.Based on the findings regarding the fresh-state,hardened-state,and durability properties of the resulting SCC mixes,it is evident that the use of RHA and MFS can significantly improve the properties of concrete.The highest compressive strength was achieved for SCC with 20 wt.%RHA and 10 wt.%MFS.This outcome should be used as a basis for further investigations into the production of concrete materials that are both high-performance and sustainable.

Properties and Mechanism on Flexural Fatigue of Polypropylene Fiber Reinforced Concrete Containing Slag

Properties and mechanism were investigated on flexural fatigue of concrete containing polypropylene fibers and ground granulated blast furnace slag（GGBFS）.Four polypropylene fibers’volume fractions and five slag proportions were considered.An experiment was conducted to obtain the fatigue lives at three stress levels in 20 Hz frequency and at a constant stress level of 0.59 in four frequency respectively.Mechanism and evaluation were investigated based on the experimental data.Fatigue life span models were established.The results show that the addition of polypropylene fibers improves the flexural fatigue cumulative strength and fatigue life span.It is proposed that the slag particles and hydrated products improve Interfacial Transition Zone（ITZ）structure and benefit flexural fatigue performance.A composite reinforce effect is found with the incorporation of slag and polypropylene fibers.The optimum mixture contents 55%slag with 0.6%polypropylene fiber for the cumulative fatigue stress.Fatigue properties are decreased as the stress level increasing,the higher frequency reduces the fatigue strength more than lower frequency at a constant stress level.

Influence of Carbonation on Fatigue of Concrete with High Volume of Ground Granulated Blast-furnace Slag

The effect of carbonation on fatigue performance of ground granulated blast-furnace slag concrete was investigated. Based on the static compression tests of carbonated GGBS-concrete, the correlation between carbonation depth and compressive strength was analyzed and an equation between carbonation depth and compressive strength was put forward. Meanwhile, fatigue S-N curves of various carbonation depths were fitted, and the infl uence of carbonation on fatigue life and strength was studied. Carbonation has a dual effect on the fatigue behavior of GGBS-concrete. A fatigue equation based on the depth of carbonation was established. Also, the probabilistic distribution of fatigue life of carbonated concrete at a given stress level was modeled by the two-parameter Weibull distribution.