The present research work reports the fabrication and evaluation of the mechanical properties of hybrid aluminium matrix composites(HAMC). Aluminium 7075(Al7075) alloy was reinforced with particles of boron carbide(B_...The present research work reports the fabrication and evaluation of the mechanical properties of hybrid aluminium matrix composites(HAMC). Aluminium 7075(Al7075) alloy was reinforced with particles of boron carbide(B_4 C) and coconut shell fly ash(CSFA). Al7075 matrix composites were fabricated by stir casting method. The samples of Al7075 HAMC were fabricated with different weight percentages of(0, 3, 6, 9 and 12 wt.%) B_4 C and 3 wt.% of CSFA. The mechanical properties discussed in this work are hardness, tensile strength, and impact strength. Hardness of the composites increased 33% by reinforcements of 12 wt.% B_4 C and 3 wt.% CSFA in aluminium 7075 alloy. The tensile strength of the composites increased 66% by the addition of 9 wt.% B_4 C and 3 wt.% CSFA in aluminium 7075 alloy. Further addition of reinforcements decreased the tensile strength of the composites. Elongation of the composites decreased while increasing B_4 C and CSFA reinforcements in the matrix. The impact energy of the composites increased up to 2.3 J with 9 wt.% B_4 C and 3 wt.% CSFA addition in aluminium alloy. Further addition of reinforcement decreased the impact strength of the composites. The optical micrographs disclosed the homogeneous distribution of reinforcement particles(B_4 C and CSFA) in Al7075 matrix. The homogeneously distributed B_4 C and CSFA particles added as reinforcement in the Al7075 alloy contributed to the improvement of hardness, tensile strength, and impact strength of the composites.展开更多
The influence of sodium silicate on the corrosion behaviour of aluminium alloy 7075-T6 in 0.1 M sodium chloride solution was studied by open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) tec...The influence of sodium silicate on the corrosion behaviour of aluminium alloy 7075-T6 in 0.1 M sodium chloride solution was studied by open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) techniques. Scanning electron microscopy (SEM) was used to characterize the AA7075-T6 surface. Silicate can significantly reduce corrosion deterioration and the inhibition efficiency increases with the concentration of Na<sub>2</sub>SiO<sub>3</sub>. The corrosion inhibition mechanism involves the formation of a protective film over the alloy surface by adsorption of aluminosilicate anions from solution, as has also been suggested by others in literature.展开更多
7XXX series aluminium alloys generally present low weldability by fusion welding methods because of the sensitivity to weld solidification cracking, vaporization of strengthening alloys and other defects in the fusion...7XXX series aluminium alloys generally present low weldability by fusion welding methods because of the sensitivity to weld solidification cracking, vaporization of strengthening alloys and other defects in the fusion zone. Friction stir welding（FSW） can be deployed successfully with aluminium alloys. We presented the effect of post-weld heat treatment（PWHT） on the microstructure and mechanical properties of SSM7075 joints. Semi solid plates were butt-welded by FSW at a rotation speed of 1110 r/min, welding speeds of 70 and 110 mm/min. Solution treatment, artificial aging, and T6（solution treatment and artificial aging combined） were applied to the welded joints, each with three samples. It was found that the T6 joints at the speed of 70 mm/min yielded the highest tensile strength of 459.23 MPa. This condition best enhanced the mechanical properties of FSW SSM7075 aluminium alloy joints.展开更多
High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Amon...High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Among these alloys, magnesium is self explosive and titanium is costlier, and aluminium is most likely to replace steels. Application of aluminium or its alloys is also thought of as an appropriate replacement in defence field, especially to enhance the easiness in mobility of combat vehicles while maintaining the same standard as that of conventional armour grade steels. Hence most of the investigations have been confined to aluminium or its alloys as base material and open an era of developing the newer composite materials to address the major limitation, i.e. tribological properties. The surface composites can be fabricated by incorporating the ceramic carbides like silicon carbide, carbides of transition metals and oxides of aluminium using surface modification techniques, such as high energy laser melt treatment, high energy electron beam irradiation and thermal spray process which are based on fusion route. These techniques yield the fusion related problems, such as interfacial reaction, pin holes, shrinkage cavities or voids and other casting related defects, and pave the way to need of an efficient technique which must be based on solid state. Recently developed friction stir processing technique was used in the present investigation for surface modification of AA7075 aluminum alloy, which is an alternative to steels. In the present investigation, 160 μm sized boron carbide powder was procured and was reduced to 60 μm and 30 μm using high energy ball mill. Subsequently these powders were used to fabricate the surface composites using friction stir processing.Ballistic performance testing as per the military standard(JIS.0108.01) was carried out. In the present work, an analytical method of predicting the ballistic behavior of surface composites was developed. This method was based on energy balance, i.e., the initial energy of impact is same as that of energy absorbed by multi layers. An attempt also has been made to validate the analytical results with the experimental findings. Variation between the analytical and experimental results may be accounted due to the assumptions considering such as isotropic behavior of target and shearing area of contact as cylindrical instead of conical interface As the analytical model yields the ballistic performance in the closer proximity of experimentally obtained, it can be considered to be an approximation to evaluate the ballistic performance of targets.展开更多
文摘The present research work reports the fabrication and evaluation of the mechanical properties of hybrid aluminium matrix composites(HAMC). Aluminium 7075(Al7075) alloy was reinforced with particles of boron carbide(B_4 C) and coconut shell fly ash(CSFA). Al7075 matrix composites were fabricated by stir casting method. The samples of Al7075 HAMC were fabricated with different weight percentages of(0, 3, 6, 9 and 12 wt.%) B_4 C and 3 wt.% of CSFA. The mechanical properties discussed in this work are hardness, tensile strength, and impact strength. Hardness of the composites increased 33% by reinforcements of 12 wt.% B_4 C and 3 wt.% CSFA in aluminium 7075 alloy. The tensile strength of the composites increased 66% by the addition of 9 wt.% B_4 C and 3 wt.% CSFA in aluminium 7075 alloy. Further addition of reinforcements decreased the tensile strength of the composites. Elongation of the composites decreased while increasing B_4 C and CSFA reinforcements in the matrix. The impact energy of the composites increased up to 2.3 J with 9 wt.% B_4 C and 3 wt.% CSFA addition in aluminium alloy. Further addition of reinforcement decreased the impact strength of the composites. The optical micrographs disclosed the homogeneous distribution of reinforcement particles(B_4 C and CSFA) in Al7075 matrix. The homogeneously distributed B_4 C and CSFA particles added as reinforcement in the Al7075 alloy contributed to the improvement of hardness, tensile strength, and impact strength of the composites.
文摘The influence of sodium silicate on the corrosion behaviour of aluminium alloy 7075-T6 in 0.1 M sodium chloride solution was studied by open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) techniques. Scanning electron microscopy (SEM) was used to characterize the AA7075-T6 surface. Silicate can significantly reduce corrosion deterioration and the inhibition efficiency increases with the concentration of Na<sub>2</sub>SiO<sub>3</sub>. The corrosion inhibition mechanism involves the formation of a protective film over the alloy surface by adsorption of aluminosilicate anions from solution, as has also been suggested by others in literature.
基金Partially Funded by National Research Universities(NRU)(ENG 5805855)Faculty of Engineering,Prince of Songkla University,Hatyai Songkhla,Thailand
文摘7XXX series aluminium alloys generally present low weldability by fusion welding methods because of the sensitivity to weld solidification cracking, vaporization of strengthening alloys and other defects in the fusion zone. Friction stir welding（FSW） can be deployed successfully with aluminium alloys. We presented the effect of post-weld heat treatment（PWHT） on the microstructure and mechanical properties of SSM7075 joints. Semi solid plates were butt-welded by FSW at a rotation speed of 1110 r/min, welding speeds of 70 and 110 mm/min. Solution treatment, artificial aging, and T6（solution treatment and artificial aging combined） were applied to the welded joints, each with three samples. It was found that the T6 joints at the speed of 70 mm/min yielded the highest tensile strength of 459.23 MPa. This condition best enhanced the mechanical properties of FSW SSM7075 aluminium alloy joints.
基金Financial assistance from Armament research board,New Delhi,India
文摘High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Among these alloys, magnesium is self explosive and titanium is costlier, and aluminium is most likely to replace steels. Application of aluminium or its alloys is also thought of as an appropriate replacement in defence field, especially to enhance the easiness in mobility of combat vehicles while maintaining the same standard as that of conventional armour grade steels. Hence most of the investigations have been confined to aluminium or its alloys as base material and open an era of developing the newer composite materials to address the major limitation, i.e. tribological properties. The surface composites can be fabricated by incorporating the ceramic carbides like silicon carbide, carbides of transition metals and oxides of aluminium using surface modification techniques, such as high energy laser melt treatment, high energy electron beam irradiation and thermal spray process which are based on fusion route. These techniques yield the fusion related problems, such as interfacial reaction, pin holes, shrinkage cavities or voids and other casting related defects, and pave the way to need of an efficient technique which must be based on solid state. Recently developed friction stir processing technique was used in the present investigation for surface modification of AA7075 aluminum alloy, which is an alternative to steels. In the present investigation, 160 μm sized boron carbide powder was procured and was reduced to 60 μm and 30 μm using high energy ball mill. Subsequently these powders were used to fabricate the surface composites using friction stir processing.Ballistic performance testing as per the military standard(JIS.0108.01) was carried out. In the present work, an analytical method of predicting the ballistic behavior of surface composites was developed. This method was based on energy balance, i.e., the initial energy of impact is same as that of energy absorbed by multi layers. An attempt also has been made to validate the analytical results with the experimental findings. Variation between the analytical and experimental results may be accounted due to the assumptions considering such as isotropic behavior of target and shearing area of contact as cylindrical instead of conical interface As the analytical model yields the ballistic performance in the closer proximity of experimentally obtained, it can be considered to be an approximation to evaluate the ballistic performance of targets.
基金Project(51474170) supported by the National Natural Science Foundation of ChinaProject(ZR19043) supported by the Xi’ an University of Architecture and Technology Natural Science Special Fund,China+1 种基金Project(2022TD-30) supported by the Scientific and Technological Innovation Team Project of Shaanxi Innovation Capability Support Plan,ChinaProject(2020JM-493) supported by the Shannxi Provincial Natural Science Foundation,China。
