Composite Panels from the Combination of Rice Husk and Wood Chips with a Natural Resin Based on Tannins Reinforced with Sugar Cane Molasses Intended for Building Insulation: Physico-Mechanical and Thermal Properties

The objective of this work is to develop new biosourced insulating composites from rice husks and wood chips that can be used in the building sector. It appears from the properties of the precursors that rice chips and husks are materials which can have good thermal conductivity and therefore the combination of these precursors could make it possible to obtain panels with good insulating properties. With regard to environmental and climatic constraints, the composite panels formulated at various rates were tested and the physico-mechanical and thermal properties showed that it was essential to add a crosslinker in order to increase certain solicitation. an incorporation rate of 12% to 30% made it possible to obtain panels with low thermal conductivity, a low surface water absorption capacity and which gives the composite good thermal insulation and will find many applications in the construction and real estate sector. Finally, new solutions to improve the fire reaction of the insulation panels are tested which allows to identify suitable solutions for the developed composites. In view of the flame tests, the panels obtained are good and can effectively combat fire safety in public buildings.

Experimental investigation of engineered geopolymer composite for structural strengthening against blast loads

The recent increase in blast/bombing incidents all over the world has pushed the development of effective strengthening approaches to enhance the blast resistance of existing civil infrastructures.Engineered geopolymer composite(EGC)is a promising material featured by eco-friendly,fast-setting and strain-hardening characteristics for emergent strengthening and construction.However,the fiber optimization for preparing EGC and its protective effect on structural elements under blast scenarios are uncertain.In this study,laboratory tests were firstly conducted to evaluate the effects of fiber types on the properties of EGC in terms of workability,dry shrinkage,and mechanical properties in compression,tension and flexure.The experimental results showed that EGC containing PE fiber exhibited suitable workability,acceptable dry shrinkage and superior mechanical properties compared with other types of fibers.After that,a series of field tests were carried out to evaluate the effectiveness of EGC retrofitting layer on the enhancement of blast performance of typical elements.The tests include autoclaved aerated concrete(AAC)masonry walls subjected to vented gas explosion,reinforced AAC panels subjected to TNT explosion and plain concrete slabs subjected to contact explosion.It was found that EGC could effectively enhance the blast resistance of structural elements in different scenarios.For AAC masonry walls and panels,with the existence of EGC,the integrity of specimens could be maintained,and their deflections and damage were significantly reduced.For plain concrete slabs,the EGC overlay could reduce the diameter and depth of the crater and spallation of specimens.

Numerical-experimental method for elastic parameters identification of a composite panel

A hybrid numerical-experimental approach to identify elastic modulus of a textile composite panel using vibration test data is proposed and investi- gated. Homogenization method is adopted to predict the initial values of elastic parameters of the composite, and parameter identification is transformed to an optimization problem in which the objective function is the minimization of the discrepancies between the experimental and numerical modal data. Case study is conducted employing a woven fabric reinforced composite panel. Three parameters （Ell, E22, G12） with higher sensitivities are selected to be identified. It is shown that the elastic parameters can be accurately identified from experimental modal data.

Development of Composite Cellular Cores for Sandwich Panels Based on Folded Polar Quadra-Structures

An idea to develop a family of cellular cores for sandwich panels using a technology of prepreg folding is presented. Polar folded quadra structures are regarded as a geometric basis for these cores whose standard frag ment has lhe fourlh degree of axial symmelry. The classification of the polar strucluresaredeseribedanda method of various quadra slrueture synthesis is developed. A possibilily to provide high strength of lhe structure due m preservation of faces reinforcement pattern is presented. Arrangemen! of the plane core on a bi curvature surface is also introduced. Besides, provision of isotropyof the core in two or three directions are described. Finally, exam ples of cellular folded cores manufaclured from basalt reinforced plaslic are demonslrated.

Stress and buckling analysis of a thick-walled micro sandwich panel with a flexible foam core and carbon nanotube reinforced composite (CNTRC) face sheets

In this paper,the stresses and buckling behaviors of a thick-walled mi-cro sandwich panel with a flexible foam core and carbon nanotube reinforced composite(CNTRC)face sheets are considered based on the high-order shear deformation theory(HSDT)and the modified couple stress theory(MCST).The governing equations of equi-librium are obtained based on the total potential energy principle.The effects of various parameters such as the aspect ratio,elastic foundation,temperature changes,and volume fraction of the canbon nanotubes(CNTs)on the critical buckling loads,normal stress,shear stress,and deflection of the thick-walled micro cylindrical sandwich panel consider-ing different distributions of CNTs are examined.The results are compared and validated with other studies,and showing an excellent compatibility.CNTs have become very use-ful and common candidates in sandwich structures,and they have been extensively used in many applications including nanotechnology,aerospace,and micro-structures.This paper also extends further applications of reinforced sandwich panels by providing the modified equations and formulae.

A STUDY OF THE POSTBUCKLING PATH OF CYLINDRICALLY CURVED PANELS OF LAMINATED COMPOSITE MATERIALS DURING LOADING AND UNLOADING

In this paper, Dynamic Relaxation Method is applied to study the postbuckling path of cylindrically curved panels of laminated composite materials during loading and unloading. The phenomenon that loading paths do not coincide with unloading paths has been found. Numerical results are given for cylindrically curved cross-ply panels subjected to uniform uniaxial compression under two types of boundary conditions. The influence of the number of layers, the panels curvature and the initial imperfection on the postbuckling paths is discussed.

Low frequency noise reduction using stiff light composite panels

The experiment presented in this paper is to investigate and analyze the noise reduction at low frequency using stiff light composite panels. Since these composite panels are made of lightweight and stiff materials, this actuation strategy will enable the creation of composite panels for duct noise control without using traditional heavy structural mass. The results suggest that the mass-spring resonance absorption in the case of a comparatively stiff thick panel with a thin flexible plate is more efficient with minimum weight, when subjected to low-frequency (<500 Hz). The efficiency of the panel absorber depends on the mass of the thin flexible plate and the stiffness of the panel.

Power transmission through double-walled laminated composite panels considering porous layer-air gap insulation

The acoustic behavior of double-walled laminated composite panels consisting of two porous and air gap middle layers is studied within the classical laminated plate theory （CLPT）. Thus, viscous and inertia coupling in a dynamic equation, as well as stress transfer, thermal and elastic coupling of porous material ave based on the Biot theory. In addition, the wave equations are extracted according to the vibration equation of composite layers. The transmission loss （TL） of the structure is then calculated by solving these equations simultaneously. Statistical energy analysis （SEA） is developed to divide the structure into specific subsystems, and power transmission is extracted with balancing power flow equations of the subsystems. Comparison between the present work and the results reported elsewhere shows excellent agreement. The results also indicate that, although favorable enhancement is seen in noise control particularly at high frequencies, the corresponding parameters associated with fluid phase and solid phase of the porous layer are important on TL according to the boundary condition interfaces. Finally, the influence of composite material and stacking sequence on power transmission is discussed.

Numerical and Experimental Study on Stiffened Composite Panel Repaired by Bolted Joints under Compressive Load

Numerical and experimental study was conducted to investigate the failure mode and strength performance of stiffened composite panel repaired by bolted joints under compressive load, and the results were then compared with those from virgin stiffened composite panel without any damage. A finite element analysis model was established for repaired and virgin stiffened composite panels under compressive load, the 3D Hashin criteria was applied to identify the composite structure failure, and the secondary stress criteria was adopted to identify the adhesive failure between the base laminate and the stiffener. The failure modes of repaired stiffened composite panels were stiffened composite panels breaking off along the bolt joints. The experimental results were consistent with the finite element analysis results, indicating the reliability of the finite element analysis model.

Potentials of <i>Bambusa vulgaris</i>Grown in Southeast Nigeria for the Manufacture of Wood-Cement Composite Panels

In this work, the potentials of Bambusa vulgaris grown in southeast Nigeria for the manufacture of wood-cement composite panels were studied. Representative culms of Bambusa vulgaris were collected from a 4-year-old stand at lower Anambra river basin, southeast, Nigeria. Fiber morphological properties and proximate chemical analysis were determined in accordance with the provisions of the Technical Association of the Pulp and Paper Industries (TAPPI, 1998). Fiber slenderness ratio was 160.95:1, component solubility of 3.09, 5.60, and 19.8 percent for cold water soak for 24 hrs;hot water soak at 80°C for 1 hr, and 1% NaOH soak for 24 hrs respectively. Composite panels were made at 1200 kg/m3 and 800 kg/m3 density levels with flakes of different soak treatments (untreated/control;cold water soak for 24 hrs;water at 80°C soak for 1 hr and 1% NaOH soak for 24 hrs) at variable cement/B. vulgaris mix ratios (1:1, 1.5:1, 2:1, 2.5:1 and 3:1 wt/wt) with 3% CaCl2 as accelerator applied to the wood furnish before cement mixing. Prepared furnish was subjected to initial pre-pressing of 0.5 N/mm2 and final consolidation of 1.4 N/mm2 retained for 24 hrs. Panels were sampled and tested after 28 days for Modulus of Rupture (MOR) and Modulus of Elasticity (MOE) in bending and for water absorption (WA) and thickness swelling (TS) due to a 24-hr water soak. Test was in accordance with provisions of American Standard for Testing of Materials (ASTM-1998). Properties ranged from a low of 25.00 to 75.45 N/mm2 for MOR;4128 to 15,065 N/mm2 for MOE;15.01 to 36.11 percent for WA and 3.04 to 12.72 percent for TA. Effect of production mix on properties was determined using factorial analysis. Except for composite density whose effect was not significant at 0.05% level, all production mix was found significant at 0.01% level at the second order level of interactions. All panels met minimum property requirements of American National Standard Institute 208-2-1994 and 208-1-1993, British Standard (BS 5669, 1979) and Malaysian Standard (MS 934, 1984).

EXPERIMENTAL STUDY ON DAMAGE TOLERANCE BEHAVIOUR OF COMPOSITE PANELS WITH SOFTENING STRIPS

In this paper an experimental study on damage tolerance behaviour of composite panels with softening strips is carried out. A prediction method of residual strength of panels with softening strips is proposed. The comparison between estimated and experimental results shows that the prediction method can be applied to design. In this paper the failure mechanisms are described.

Manufacturing cost optimization and estimation combined computer of composite-stiffened panels

The primary goal of this study is to fully grasp the production flow of the new processing technologies for manufacturing composite stiffened panels incorporating cost as one of the design variables early in the design process. An approach is presented to determine the optimum process for cost as objective function. A cost estimation model is established based on the integrally molding process. In the model,the cost drivers which are related to the manufacture processes in terms of material,labor,tool and equipment costs are taken into account. At the same time,estimation software combined computer is developed to aid optimization design. A case of manufacturing composite stiffened panels with T-shaped stiffeners is examined. Excellent agreement shows the optimum process for cost is obtained for the composite stiffened panel with cocuring. It is also revealed that the estimation software combined computer is efficient. The estimation methodology is valid to guide design of the manufacturing process for the composite-stiffened panel.

贴敷宏纤维复合材料片的飞机壁板振动响应预测

传统的有限元模型存在计算成本高、黑箱操作多、缺乏自主知识产权等问题。采用解析法研究基础谐波激励下贴敷宏纤维复合材料(MFC)片的飞机壁板振动响应的预测问题;基于经典层合板理论、机电耦合本构方程和能量法,建立基础谐波激励下MFC-壁板的解析模型;利用速度反馈法和模态叠加原理,实现对该激励条件下结构系统在主动控制前后振动响应的求解;结合文献和组建的振动测试系统获得的实验数据,对该解析模型及其预测结果进行详细验证。结果表明:相较于文献结果,模型等固有频率计算偏差最大不超过2%,模型预测获得的前两阶共振响应的最大误差不超过8.6%,均在误差允许的范围内。

结构-功能一体化异种复合材料壁板优化与验证

基于航空壁板结构承载-电气功能的一体化需求,对适用于智能蒙皮的异种复合材料壁板开展了优化设计与试验验证。通过在高模量碳纤维蒙皮的外侧增加玻璃纤维层,进行了以碳纤维-玻璃纤维-金属结构单元阵列-玻璃纤维复合顺序的壁板承载-电气功能一体化设计。针对异种复合材料结构的铺层优化需要考虑共胶接的分区域及铺层连续性的工艺要求,发展了基于丢层序列的优化方法,并对于加筋壁板的几何外形、筋条数量、筋条几何参数以及筋条与蒙皮的铺层角度进行了优化设计。通过压缩稳定性试验验证了该结构在承载能力和稳定性方面的收益,明晰了其压缩载荷下的屈曲模态及后屈曲失效机理。

真空绝热板芯材的研究进展与展望

随着我国经济的迅速发展和人们对生活水平的要求越来越高,节能减排对实现“碳达峰”和“碳中和”的目标显得越来越重要。真空绝热板(vacuum insolation panels,VIP)是一种新型的高效保温隔热材料,其中,芯材作为VIP的核心和骨架结构,不仅承担着支撑作用,而且是板内热量传递的主要通道,对保证VIP的保温性能具有关键作用。基于此,本文首先重点介绍了真空绝热板在绿色建筑和冷链物流领域应用的意义,明确了目前制约真空绝热板领域发展的关键问题;随后综述了真空绝热板芯材的研究现状和进展,比对了不同种类芯材(颗粒类芯材、泡沫类芯材、纤维类芯材、生物质材料类芯材和复合类芯材)在原料来源、保温性能、生产工艺及环境保护方面的优劣,将绿色、可再生的生物质基材料用作真空绝热板芯材进行了对比探讨;最后对真空绝热板芯材未来的研究方向和发展前景进行了总结和展望。本文指出,传统以玻璃纤维、有机泡沫或者气相二氧化硅为芯材的真空绝热板,存在生产成本高、不可再生、难降解、污染环境等问题,所以通过功能化手段获得新型、绿色、低成本、具有良好微观孔隙结构和高热阻的芯材是制约真空绝热板发展的关键。生物质材料具有来源广泛、成本低廉、绿色环保、孔隙结构丰富等优点,是一种极具潜力的VIP芯材原料,也将是真空绝热板芯材的重要研究方向。因此,生物质基芯材真空绝热板未来的发展还需进一步拓宽其原料来源、改善制备方法和工艺、明确老化和使役性能、关注复合芯材的开发,不断提高VIP的性能,扩展其应用领域。

飞机复合材料机身壁板装配技术分析与展望

复合材料以其优异的综合性能在航空航天领域得到了大量应用,其应用范围逐渐从次承力结构向主承力结构扩展,包括在机身结构的组成方面,传统的金属组装壁板逐渐被复合材料整体壁板所取代。由于复合材料壁板具有不同于传统金属材料壁板的装配工艺特点,因此对其装配方法和装配工艺提出了新的要求。针对圆筒状机身复合材料机身壁板的装配过程,分别介绍了复合材料机身壁板大尺寸测量技术、复合材料机身壁板装配定位调姿技术和复合材料机身壁板的先进制孔连接技术,系统总结了近年来国内外相关研究进展和应用情况,指出了飞机大尺寸复合材料结构装配技术未来的研究与应用方向。

日本UFC桥面板和UFC组合桥面板的研发与应用

日本较早期建设的城市高速公路桥梁中主要采用钢桥面板和混凝土桥面板。针对钢桥面板的焊缝疲劳开裂和混凝土桥面板的老化现象,研发了超高强度纤维增强混凝土桥面板(UFC桥面板)及UFC组合桥面板,具有高强度、高耐久性。UFC桥面板分为平板型和方格肋型2种类型,可应用于既有公路桥梁的桥面板更换以及新建公路桥梁的桥面板。UFC组合桥面板为在预制PC桥面板顶面设UFC层作为防水层,可省去预制PC桥面板防水层施工,提高施工效率。UFC桥面板和UFC组合桥面板在预制场预制、现场安装,施工便捷,已实际应用在阪神高速公路15号堺线玉出匝道桥桥面板更换工程、阪神高速公路1号环线信浓桥匝道桥新建桥梁工程、东北高速公路宫城白石川桥上行线既有桥面板更换等工程上,可提高桥梁结构的耐久性、减少桥梁养护工作量、降低养护成本。

一种新型结构与保温一体化复合墙板节点试验

为解决复合墙板节点常见的保温板易燃、易脱落等棘手问题,并使其抗震性能良好。给出了一种新型的结构与保温一体化陶粒混凝土T型复合墙板节点。该复合墙板节点具有夹芯独特构造优势,主要表现在绿色节能,轻质高强,力学性能好,保温系统连接可靠,还能杜绝火灾的发生。通过对T型复合墙板节点进行抗震试验,分别研究了其滞回性能、破坏机理、承载及变形能力、延性、耗能、损伤等。结果表明:一体化复合墙板节点的破坏顺序为腹板-翼缘-节点核心区;薄弱位置主要发生在腹板脚部,混凝土被拉裂或压碎,钢筋被拉长或压弯等;节点核心区受力相对良好,安全储备充足;符合“强节点,弱构件”设计要求和墙板革新发展政策。延性系数大于3,墙板节点安全性能良好。通过损伤指标评估分析,了解了试件各阶段工作状态。

组合梁桥负弯矩区后张预制板抗裂技术研究

对于跨径小于50 m的桥梁,使用强配筋能很好地满足抗裂性能要求,但对于更大跨径的组合梁桥负弯矩抗裂,单独采用强配筋的方式已不能很好地满足桥梁抗裂需求。为了提高50~80 m连续组合梁桥负弯矩区桥面板抗裂性能,实现负弯矩区桥面板装配建造,提出一种适用不同抗裂能力的模数式预应力预制板。首先,设计了适合负弯矩区快速施工的3类预制板,其中A类板为中间位置普通预制板,B类板为带齿块的锚固板,C类板为端部锚固板,根据实际受力情况采用这3类预制板数量及长度组合以满足抗裂需要。其次,结合设计规范与数值模拟,验算使用这种抗裂技术时桥梁结构的内力、应力、挠度以及抗裂性能,验证其可行性。最后,进一步扩展到中跨径50~80 m、1.5~1.7边中跨比的组合梁桥,分别采用MIDAS进行结构抗裂验算与适用性分析。结果表明:采用后张预应力预制板抗裂技术可实现预制板翼缘应力在长短期组合下不出现拉应力,满足规范A类构件抗裂要求;养护龄期6个月的预制块在降低徐变作用方面效果明显,降幅均在48%左右,可满足50~80 m主跨跨径组合梁桥桥面板抗裂与钢箱梁强度控制规范要求;采用负弯矩预制板后,相较于规范计算结果,负弯矩长度范围略降低,仍可采用规范中偏安全的计算。

秸秆膨化技术及高效应用的研究

我国拥有丰富的秸秆资源,然而,其中大部分尚未得到有效开发利用,造成了资源的浪费。因此,秸秆膨化技术的发展及其高效利用成为不可回避的趋势。首先对农作物秸秆的主要成分进行了介绍,随后深入综述了螺杆膨化机的工作原理,详述了单螺杆、双螺杆和三螺杆膨化机在秸秆膨化领域的研究历程,并对各类膨化机的优劣进行了分析。同时,还对膨化过程中的影响因素进行了综合总结。根据秸秆膨化的应用,展望了秸秆在制浆、复合板材和乙醇方面的利用,为高效利用秸秆提供了理论指导。