Plasma electrolytic oxidation (PEO) ceramic coatings were fabricated in a silicate-based electrolyte with the addition of potassium fluorozirconate (K2ZrF6) on 6063 aluminum alloy, and the effects of current density o...Plasma electrolytic oxidation (PEO) ceramic coatings were fabricated in a silicate-based electrolyte with the addition of potassium fluorozirconate (K2ZrF6) on 6063 aluminum alloy, and the effects of current density on microstructure and properties of the PEO coatings were studied. It was found that pore density of the coatings decreased with increasing the current density. The tribological and hardness tests suggested that the ceramic coating produced under the current density of 15 A/dm2showed the best mechanical property, which matched well with the phase analysis. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curves proved that the coating obtained under 15 A/dm2 displayed the best anti-corrosion property, which was directly connected with morphologies of coatings.展开更多
After electrolytically etched pattern graining surface of aluminum alloy, it is shows that there are porous oxide film containing α Al 2O 3 and α Al 2O 3 by means of SEM XRD and XPS analysis. In the ditches, a...After electrolytically etched pattern graining surface of aluminum alloy, it is shows that there are porous oxide film containing α Al 2O 3 and α Al 2O 3 by means of SEM XRD and XPS analysis. In the ditches, anodic oxidation makes pore density and diameter larger than other areas, and causes more coloring metal depositing and mutual cross linking. The electrolytically etched pattern surface shows relative deeper color on the ditches and lighter color on other areas, so it can be used for decoration. Electrolytic coloring metal exists in forms of Ag colloid and Ag 2O. Both anodic oxidation and electrolytic coloring affect the surface microstructure of aluminum alloy.展开更多
Welding is a vital component of several industries such as automotive,aerospace,robotics,and construction.Without welding,these industries utilize aluminum alloys for the manufacturing of many components or systems.Ho...Welding is a vital component of several industries such as automotive,aerospace,robotics,and construction.Without welding,these industries utilize aluminum alloys for the manufacturing of many components or systems.However,fusion welding of aluminum alloys is challenging due to several factors,including the presence of non-heat-treatable alloys,porosity,solidification,and liquation of cracks.Many manufacturers adopt conventional in-air friction stir welding(FSW)to weld metallic alloys and dissimilar materials.Many researchers reported the drawbacks of this traditional in-air FSW technique in welding metallic and polymeric materials in general and aluminum alloys and aluminum matrix composites in specific.A number of FSW techniques were developed recently,such as underwater friction stir welding(UFSW),vibrational friction-stir welding(VFSW),and others,for welding of aluminum alloy joints to overcome the issues of welding using conventional FSW.Therefore,the main objective of this review is to summarize the recent trends in FSW process of aluminum alloys and aluminum metal matrix composites(Al MMCs).Also,it discusses the effect of welding parameters of the traditional and state-of-the-art developed FSW techniques on the welding quality and strength of aluminum alloys and Al MMCs.Comparison among the techniques and advantages and limitations of each are considered.The review suggests that VFSW is a viable option for welding aluminum joints due to its energy efficiency,economic cost,and versatile modifications that can be employed based on the application.This review also illustrated that significantly less attention has been paid to FSW of Al-MMCs and considerable attention is demanded to produce qualified joint.展开更多
Aluminum alloy base surface hybrid composites were fabricated by incorporating with mixture of （SiC＋Gr） and （SiC＋Al2O3） particles of 20 μm in average size on an aluminum alloy 6061-T6 plate using friction stir ...Aluminum alloy base surface hybrid composites were fabricated by incorporating with mixture of （SiC＋Gr） and （SiC＋Al2O3） particles of 20 μm in average size on an aluminum alloy 6061-T6 plate using friction stir processing （FSP）. Microstructures of both the surface hybrid composites revealed that SiC, Gr and Al2O3 are uniformly dispersed in the nugget zone （NZ）. It was observed that the addition of Gr particles rather than Al2O3 particles with SiC particles, decreases the microhardness but immensely increases the dry sliding wear resistance of aluminum alloy 6061-T6 surface hybrid composite. The observed microhardness and wear properties are correlated with microstructures and worn micrographs.展开更多
SiCp/2024 matrix composites reinforced with SiC particles and 2219 aluminum alloy were joined via centered electron beam welding and deflection beam welding,respectively,and the microstructures and mechanical properti...SiCp/2024 matrix composites reinforced with SiC particles and 2219 aluminum alloy were joined via centered electron beam welding and deflection beam welding,respectively,and the microstructures and mechanical properties of these joints were investigated.The results revealed that SiC particle segregation was more likely during centered electron beam welding(than during deflection beam welding),and strong interface reactions led to the formation of many Al4C3 brittle intermetallic compounds.Moreover,the tensile strength of the joints was 104 MPa.The interface reaction was restrained via deflection electron beam welding,and only a few Al4C3 intermetallic compounds formed at the top of the joint and heat affected zone of SiCp/Al.Quasi-cleavage fracture occurred at the interface reaction layer of the base metal.Both methods yielded a hardness transition zone near the SiCp/2024 fusion zone,and the brittle intermetallic Al4C3compounds formed in this zone resulted in high hardness.展开更多
The 1050 aluminum alloy strip was prepared by means of electromagnetic and ultrasonic cast rolling on the modified asymmetric twin roll caster, and then the aluminum substrate for presensitized plate was prepared thro...The 1050 aluminum alloy strip was prepared by means of electromagnetic and ultrasonic cast rolling on the modified asymmetric twin roll caster, and then the aluminum substrate for presensitized plate was prepared through cold rolling and annealing.The effects of electromagnetic and ultrasonic cast rolling on microstructure, mechanical properties, surface roughness and electrolytic corrosion properties of 1050 aluminum substrate were studied. The results show that electromagnetic and ultrasonic cast rolling can decrease the average crystallite size of aluminum substrate by 5 μm, increase the crystal boundaries with uniform distribution, and make the second-phase particles with smaller size distributed dispersively in the substrate, meanwhile, it can increase the tensile strength, elongation and micro-hardness by 4.58%, 9.85% and HV 2, respectively, reduce the surface roughness, make the surface appearance more even, electrolytic corrosion polarization curve of aluminum substrate more smooth and the surface corrosion pits with regular shape more dispersive.展开更多
Rice husk ash(RHA) is a potential particulate reinforcement to produce aluminum matrix composites(AMCs)economically.Compocasting method was applied to produce aluminum alloy AA6061 reinforced with various amounts(0,2%...Rice husk ash(RHA) is a potential particulate reinforcement to produce aluminum matrix composites(AMCs)economically.Compocasting method was applied to produce aluminum alloy AA6061 reinforced with various amounts(0,2%,4%,6%and 8%,mass fraction) of RHA particles.The prepared composites were characterized using X-ray diffraction and scanning electron microscopy.X-ray diffraction patterns of AA6061/RHA AMCs revealed the presence of RHA particles without the formation of any other intermetallic compounds.The scanning electron micrographs showed a homogeneous distribution of RHA particles all over the aluminum matrix.Intragranular distribution of RHA particles was observed.Further,RHA particles were bonded well with the aluminum matrix and a clear interface existed.The reinforcement of RHA particles enhanced the microhardness and ultimate tensile strength(UTS) of the AMCs.The tensile behavior is correlated to the microstructure of the AMCs.展开更多
The effect of microstructure variation by addition of alumina short fiber and optimization of tensile properties by air cooling processing in Al 2O 3/Al 15Si composites were studied. The results show that in Al 15Si a...The effect of microstructure variation by addition of alumina short fiber and optimization of tensile properties by air cooling processing in Al 2O 3/Al 15Si composites were studied. The results show that in Al 15Si alloy matrix composites with 14% and 30%(volume fraction) fiber, the primary silicon is hardly refined, but the eutectic silicon is effectively refined and granulated. Granulation of some eutectic silicon mainly happens in fiber segregation areas. Refining and granulation of the eutectic silicon are related to the physical constraint arising from the fiber. After the 30%Al 2O 3/Al 15Si composite was remelted and air cooled, the number of the eutectic silicon on the surface of the fiber increases, which results in the improvement of fiber/matrix interface and tensile properties for the as cast composite. Air cooling processing may be reliable for the optimization of the microstructure and properties of fiber reinforced hypereutectic Al 15Si alloy composites.展开更多
In order to improve mechanical properties of 6082 aluminum alloy,the SiC_(p)/Al 6082 composites were prepared by the addition of the micron-sized SiC_(p)articles combined with the squeeze casting.The effects of the Si...In order to improve mechanical properties of 6082 aluminum alloy,the SiC_(p)/Al 6082 composites were prepared by the addition of the micron-sized SiC_(p)articles combined with the squeeze casting.The effects of the SiC_(p)content and squeeze casting on the microstructure and mechanical properties of the 6082 aluminum alloy were investigated by SEM,EDS,TEM,tensile testing and hardness testing analysis methods.Research results exhibited that the SiC_(p)content and squeeze casting had a significant impact on the microstructure and mechanical properties of the 6082 aluminum alloy.The addition of the SiC_(p)refined the grain size of the 6082 aluminum alloy while caused the increase of the porosity with increasing the SiC_(p)content,especially in the permanent mold casting condition.Compared to the permanent mold casting,the squeeze casting obviously reduced pore defects,refined grain size and made the SiC_(p)distribute evenly as well as bond tightly with the Al matrix.The tensile strength,yield strength,elongation,elastic modulus and hardness of the 6082 aluminum alloy obtained with the SiC_(p)and squeeze casting were remarkably improved,and the optimal mechanical properties were obtained with a 2 wt.%SiC_(p),and they increased 10.73%,72.7%,193.9%,23.5%and 25.2%,respectively,compared to those of the6082 aluminum alloy obtained without SiC_(p)and squeeze casting.The fracture surface of the SiC_(p)/Al 6082 composites obtained with the squeeze casting was dense and exhibited a ductile fracture mode.展开更多
Ni–Al powder and Ni–Al composite coatings were fabricated by twin-wire arc spraying（TWAS）. The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy（SEM） ...Ni–Al powder and Ni–Al composite coatings were fabricated by twin-wire arc spraying（TWAS）. The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy（SEM） and energy dispersive spectroscopy（EDS）. The results showed that the obtained particle size ranged from 5 to 50 μm. The morphology of the Ni–Al powder showed that molten particles were composed of Ni solid solution, NiAl, Ni_3Al, Al_2O_3, and NiO. The Ni–Al phase and a small amount of Al_2O_3 particles changed the composition of the coating. The microstructures of the twin-wire-arc-sprayed Ni–Al composite coatings were characterized by SEM, EDS, X-ray diffraction（XRD）, and transmission electron microscopy（TEM）. The results showed that the main phase of the Ni-5wt%Al coating consisted of Ni solid solution and Ni Al in addition to a small amount of Al_2O_3. The main phase of the Ni-20wt%Al coating mainly consisted of Ni solid solution, Ni Al, and Ni_3Al in addition to a small amount of Al and Al_2O_3, and Ni Al and Ni_3Al intermetallic compounds effectively further improved the final wear property of the coatings. TEM analysis indicated that fine spherical NiAl_3 precipitates and a Ni–Al–O amorphous phase formed in the matrix of the Ni solid solution in the original state.展开更多
The 6351 wrought aluminum alloy and K2TiF6-CaF2-LiCl components were selected as raw materials to fabricate in situ Al3Ti particulate reinforced aluminum alloy at 720℃via direct melt reaction method with electromagne...The 6351 wrought aluminum alloy and K2TiF6-CaF2-LiCl components were selected as raw materials to fabricate in situ Al3Ti particulate reinforced aluminum alloy at 720℃via direct melt reaction method with electromagnetic stirring(EMS).CaF2 and LiCl acted as fluxes to lower the reaction temperature of the system.It is shown that the electromagnetic stirring and fluxes accelerate the emulsion process of K2TiF6.Optical microscopy,scanning electron microscopy,transmission electron microscopy and energy dispersive spectrum were utilized to analyze the microstructure and components of composites.Compared to composites fabricated without EMS and fluxes,the sizes of endogenetic Al3Ti are refined from 10-15μm to 2-4μm,which are often accompanied with silicon element.The morphology of Al3Ti or Al3TiSi0.22 exhibits triangle,quadrilateral and other clumpy patterns. Because of the Ca elements from CaF2,the sizes of Mg2Si decrease from 8-10μm to 1-2μm due to the formation of Ca2Si.展开更多
The microstructure formation and strengthening of an Al-5 wt.%TiO2 composites with additions of 5 wt.%Cu and 2 wt.% stearic acid(as a process control agent, PCA) during mechanical alloying and subsequent thermal expos...The microstructure formation and strengthening of an Al-5 wt.%TiO2 composites with additions of 5 wt.%Cu and 2 wt.% stearic acid(as a process control agent, PCA) during mechanical alloying and subsequent thermal exposure were studied. The powder composites were prepared by high-energy ball milling for up to 10 h. Single line tracks of the powders were laser melted. Optical and scanning electron microscopy, XRD analysis and differential scanning calorimetry were used to study microstructural evolution. The results showed that the Cu addition promotes an effective mechanical alloying of aluminum with Ti O2 from the start of milling, resulting in higher microhardness(up to HV 290), while the PCA, on the contrary, postpones this process. In both cases, the composite granules with uniform distribution of Ti O2 particles were formed. Subsequent heating of mechanically alloyed materials causes the activation of an exothermic reaction of Ti O2 reduction with aluminum, the start temperature of which, in the case of Cu addition,shifts to lower values, that is, the transformation begins in the solid state. Besides, the Cu-added material after laser melting demonstrates a more dispersed and uniform structure which positively affects its microhardness.展开更多
In-situ 2 vol.%TiB2 particle reinforced Al−xSi−0.3Mg(x=7,9,12,15 wt.%)composites were prepared by the salt−metal reaction,and the microstructures and mechanical properties were investigated.The results show that the T...In-situ 2 vol.%TiB2 particle reinforced Al−xSi−0.3Mg(x=7,9,12,15 wt.%)composites were prepared by the salt−metal reaction,and the microstructures and mechanical properties were investigated.The results show that the TiB2 particles with a diameter of 20−80 nm and the eutectic Si with a length of 1−10μm are the main strengthening phases in the TiB2/Al−xSi−0.3Mg composites.The TiB2 particles promote grain refinement and modify the eutectic Si from needle-like to short-rod shape.However,the strengthening effect of TiB2 particles is weakened as the Si content exceeds the eutectic composition,which can be attributed to the formation of large and irregular primary Si.The axial tensile test results and fractography observations indicate that these composites show more brittle fracture characteristics than the corresponding alloy matrixes.展开更多
Multi-wall carbon nanotubes (MWNTs) have high mechanical properties and are considered a kind of realistic reinforcement for polymers, ceramics and metals. The hot press sintering and squeeze casting were adopted to s...Multi-wall carbon nanotubes (MWNTs) have high mechanical properties and are considered a kind of realistic reinforcement for polymers, ceramics and metals. The hot press sintering and squeeze casting were adopted to synthesize MWNTs reinforced aluminum composites. In hot press sintered MWNTs/Al composites, MWNTs agglomerates distribute along aluminum powders and have low bonding strength with aluminum. But MWNTs agglomerates distribute evenly in the squeeze cast MWNTs/Al composites. Some dispersed nanotubes bond well with aluminum matrix and few dislocations can be found in the nanotube areas, which implies little thermal residual stress in squeeze cast MWNTs/Al composites. This indicates that the strengthen mechanisms in nanometer sized MWNTs/Al composites may be different from that in micrometer sized whisker composites.展开更多
基金Project(51371039)supported by the National Natural Science Foundation of China
文摘Plasma electrolytic oxidation (PEO) ceramic coatings were fabricated in a silicate-based electrolyte with the addition of potassium fluorozirconate (K2ZrF6) on 6063 aluminum alloy, and the effects of current density on microstructure and properties of the PEO coatings were studied. It was found that pore density of the coatings decreased with increasing the current density. The tribological and hardness tests suggested that the ceramic coating produced under the current density of 15 A/dm2showed the best mechanical property, which matched well with the phase analysis. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curves proved that the coating obtained under 15 A/dm2 displayed the best anti-corrosion property, which was directly connected with morphologies of coatings.
文摘After electrolytically etched pattern graining surface of aluminum alloy, it is shows that there are porous oxide film containing α Al 2O 3 and α Al 2O 3 by means of SEM XRD and XPS analysis. In the ditches, anodic oxidation makes pore density and diameter larger than other areas, and causes more coloring metal depositing and mutual cross linking. The electrolytically etched pattern surface shows relative deeper color on the ditches and lighter color on other areas, so it can be used for decoration. Electrolytic coloring metal exists in forms of Ag colloid and Ag 2O. Both anodic oxidation and electrolytic coloring affect the surface microstructure of aluminum alloy.
基金United Arab Emirates University (UAEU), Al-Ain, UAE, and Sultan Qaboos University (SQU), Muscat, Sultanate of Oman, for providing research support through a collaborative research project (UAEU: 31N270)。
文摘Welding is a vital component of several industries such as automotive,aerospace,robotics,and construction.Without welding,these industries utilize aluminum alloys for the manufacturing of many components or systems.However,fusion welding of aluminum alloys is challenging due to several factors,including the presence of non-heat-treatable alloys,porosity,solidification,and liquation of cracks.Many manufacturers adopt conventional in-air friction stir welding(FSW)to weld metallic alloys and dissimilar materials.Many researchers reported the drawbacks of this traditional in-air FSW technique in welding metallic and polymeric materials in general and aluminum alloys and aluminum matrix composites in specific.A number of FSW techniques were developed recently,such as underwater friction stir welding(UFSW),vibrational friction-stir welding(VFSW),and others,for welding of aluminum alloy joints to overcome the issues of welding using conventional FSW.Therefore,the main objective of this review is to summarize the recent trends in FSW process of aluminum alloys and aluminum metal matrix composites(Al MMCs).Also,it discusses the effect of welding parameters of the traditional and state-of-the-art developed FSW techniques on the welding quality and strength of aluminum alloys and Al MMCs.Comparison among the techniques and advantages and limitations of each are considered.The review suggests that VFSW is a viable option for welding aluminum joints due to its energy efficiency,economic cost,and versatile modifications that can be employed based on the application.This review also illustrated that significantly less attention has been paid to FSW of Al-MMCs and considerable attention is demanded to produce qualified joint.
文摘Aluminum alloy base surface hybrid composites were fabricated by incorporating with mixture of （SiC＋Gr） and （SiC＋Al2O3） particles of 20 μm in average size on an aluminum alloy 6061-T6 plate using friction stir processing （FSP）. Microstructures of both the surface hybrid composites revealed that SiC, Gr and Al2O3 are uniformly dispersed in the nugget zone （NZ）. It was observed that the addition of Gr particles rather than Al2O3 particles with SiC particles, decreases the microhardness but immensely increases the dry sliding wear resistance of aluminum alloy 6061-T6 surface hybrid composite. The observed microhardness and wear properties are correlated with microstructures and worn micrographs.
基金Project was supported by the National Nature Science Foundation of China(51375115).
文摘SiCp/2024 matrix composites reinforced with SiC particles and 2219 aluminum alloy were joined via centered electron beam welding and deflection beam welding,respectively,and the microstructures and mechanical properties of these joints were investigated.The results revealed that SiC particle segregation was more likely during centered electron beam welding(than during deflection beam welding),and strong interface reactions led to the formation of many Al4C3 brittle intermetallic compounds.Moreover,the tensile strength of the joints was 104 MPa.The interface reaction was restrained via deflection electron beam welding,and only a few Al4C3 intermetallic compounds formed at the top of the joint and heat affected zone of SiCp/Al.Quasi-cleavage fracture occurred at the interface reaction layer of the base metal.Both methods yielded a hardness transition zone near the SiCp/2024 fusion zone,and the brittle intermetallic Al4C3compounds formed in this zone resulted in high hardness.
基金Project(2014CB046702) supported by the National Basic Research Program of ChinaProject supported by the Postdoctoral Science Foundation of Central South University,China
文摘The 1050 aluminum alloy strip was prepared by means of electromagnetic and ultrasonic cast rolling on the modified asymmetric twin roll caster, and then the aluminum substrate for presensitized plate was prepared through cold rolling and annealing.The effects of electromagnetic and ultrasonic cast rolling on microstructure, mechanical properties, surface roughness and electrolytic corrosion properties of 1050 aluminum substrate were studied. The results show that electromagnetic and ultrasonic cast rolling can decrease the average crystallite size of aluminum substrate by 5 μm, increase the crystal boundaries with uniform distribution, and make the second-phase particles with smaller size distributed dispersively in the substrate, meanwhile, it can increase the tensile strength, elongation and micro-hardness by 4.58%, 9.85% and HV 2, respectively, reduce the surface roughness, make the surface appearance more even, electrolytic corrosion polarization curve of aluminum substrate more smooth and the surface corrosion pits with regular shape more dispersive.
文摘Rice husk ash(RHA) is a potential particulate reinforcement to produce aluminum matrix composites(AMCs)economically.Compocasting method was applied to produce aluminum alloy AA6061 reinforced with various amounts(0,2%,4%,6%and 8%,mass fraction) of RHA particles.The prepared composites were characterized using X-ray diffraction and scanning electron microscopy.X-ray diffraction patterns of AA6061/RHA AMCs revealed the presence of RHA particles without the formation of any other intermetallic compounds.The scanning electron micrographs showed a homogeneous distribution of RHA particles all over the aluminum matrix.Intragranular distribution of RHA particles was observed.Further,RHA particles were bonded well with the aluminum matrix and a clear interface existed.The reinforcement of RHA particles enhanced the microhardness and ultimate tensile strength(UTS) of the AMCs.The tensile behavior is correlated to the microstructure of the AMCs.
文摘The effect of microstructure variation by addition of alumina short fiber and optimization of tensile properties by air cooling processing in Al 2O 3/Al 15Si composites were studied. The results show that in Al 15Si alloy matrix composites with 14% and 30%(volume fraction) fiber, the primary silicon is hardly refined, but the eutectic silicon is effectively refined and granulated. Granulation of some eutectic silicon mainly happens in fiber segregation areas. Refining and granulation of the eutectic silicon are related to the physical constraint arising from the fiber. After the 30%Al 2O 3/Al 15Si composite was remelted and air cooled, the number of the eutectic silicon on the surface of the fiber increases, which results in the improvement of fiber/matrix interface and tensile properties for the as cast composite. Air cooling processing may be reliable for the optimization of the microstructure and properties of fiber reinforced hypereutectic Al 15Si alloy composites.
基金financially supported by the National Key Research and Development Program of China(Nos.2020YFB2008300 and 2020YFB2008304)the State Key Laboratory of High Performance Complex Manufacturing in CSU(No.Kfkt2019-01)the Analytical and Testing Center,HUST。
文摘In order to improve mechanical properties of 6082 aluminum alloy,the SiC_(p)/Al 6082 composites were prepared by the addition of the micron-sized SiC_(p)articles combined with the squeeze casting.The effects of the SiC_(p)content and squeeze casting on the microstructure and mechanical properties of the 6082 aluminum alloy were investigated by SEM,EDS,TEM,tensile testing and hardness testing analysis methods.Research results exhibited that the SiC_(p)content and squeeze casting had a significant impact on the microstructure and mechanical properties of the 6082 aluminum alloy.The addition of the SiC_(p)refined the grain size of the 6082 aluminum alloy while caused the increase of the porosity with increasing the SiC_(p)content,especially in the permanent mold casting condition.Compared to the permanent mold casting,the squeeze casting obviously reduced pore defects,refined grain size and made the SiC_(p)distribute evenly as well as bond tightly with the Al matrix.The tensile strength,yield strength,elongation,elastic modulus and hardness of the 6082 aluminum alloy obtained with the SiC_(p)and squeeze casting were remarkably improved,and the optimal mechanical properties were obtained with a 2 wt.%SiC_(p),and they increased 10.73%,72.7%,193.9%,23.5%and 25.2%,respectively,compared to those of the6082 aluminum alloy obtained without SiC_(p)and squeeze casting.The fracture surface of the SiC_(p)/Al 6082 composites obtained with the squeeze casting was dense and exhibited a ductile fracture mode.
基金financially supported by the International Cooperation Project Foundation in Science and Technology of China(No.2008DFR50070)
文摘Ni–Al powder and Ni–Al composite coatings were fabricated by twin-wire arc spraying（TWAS）. The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy（SEM） and energy dispersive spectroscopy（EDS）. The results showed that the obtained particle size ranged from 5 to 50 μm. The morphology of the Ni–Al powder showed that molten particles were composed of Ni solid solution, NiAl, Ni_3Al, Al_2O_3, and NiO. The Ni–Al phase and a small amount of Al_2O_3 particles changed the composition of the coating. The microstructures of the twin-wire-arc-sprayed Ni–Al composite coatings were characterized by SEM, EDS, X-ray diffraction（XRD）, and transmission electron microscopy（TEM）. The results showed that the main phase of the Ni-5wt%Al coating consisted of Ni solid solution and Ni Al in addition to a small amount of Al_2O_3. The main phase of the Ni-20wt%Al coating mainly consisted of Ni solid solution, Ni Al, and Ni_3Al in addition to a small amount of Al and Al_2O_3, and Ni Al and Ni_3Al intermetallic compounds effectively further improved the final wear property of the coatings. TEM analysis indicated that fine spherical NiAl_3 precipitates and a Ni–Al–O amorphous phase formed in the matrix of the Ni solid solution in the original state.
基金financially supported by the Russian Science Foundation(No.20-19-00746)(SEM,DSC,thermodynamic calculations)the federal academic leadership program Priority 2030 of NUST MISIS(DFT,XRD)。
基金Project(2007AA03Z548)supported by the National High-Tech Research and Development Program of ChinaProject(207038)supported by the Key Program of Ministry of Education of China+3 种基金Project(06-D-021)supported by the Talents Peak in Six Key Fields of Jiangsu Province in ChinaProject(07JDG084)supported by the Technical Enablement Foundation for the Super Special Talents of Jiangsu UniversityProject(20071108)supported by the Technical Enablement Foundation of Ministry of Education for the Returned ScholarsProject(20060299006)supported by the PhD Programs Foundation of Ministry of Education of China
文摘The 6351 wrought aluminum alloy and K2TiF6-CaF2-LiCl components were selected as raw materials to fabricate in situ Al3Ti particulate reinforced aluminum alloy at 720℃via direct melt reaction method with electromagnetic stirring(EMS).CaF2 and LiCl acted as fluxes to lower the reaction temperature of the system.It is shown that the electromagnetic stirring and fluxes accelerate the emulsion process of K2TiF6.Optical microscopy,scanning electron microscopy,transmission electron microscopy and energy dispersive spectrum were utilized to analyze the microstructure and components of composites.Compared to composites fabricated without EMS and fluxes,the sizes of endogenetic Al3Ti are refined from 10-15μm to 2-4μm,which are often accompanied with silicon element.The morphology of Al3Ti or Al3TiSi0.22 exhibits triangle,quadrilateral and other clumpy patterns. Because of the Ca elements from CaF2,the sizes of Mg2Si decrease from 8-10μm to 1-2μm due to the formation of Ca2Si.
基金the Ministry of Education and Science of the Russian Federation in the framework of the State Assignment to the Universities(Project No.11.7172.2017/8.9).
文摘The microstructure formation and strengthening of an Al-5 wt.%TiO2 composites with additions of 5 wt.%Cu and 2 wt.% stearic acid(as a process control agent, PCA) during mechanical alloying and subsequent thermal exposure were studied. The powder composites were prepared by high-energy ball milling for up to 10 h. Single line tracks of the powders were laser melted. Optical and scanning electron microscopy, XRD analysis and differential scanning calorimetry were used to study microstructural evolution. The results showed that the Cu addition promotes an effective mechanical alloying of aluminum with Ti O2 from the start of milling, resulting in higher microhardness(up to HV 290), while the PCA, on the contrary, postpones this process. In both cases, the composite granules with uniform distribution of Ti O2 particles were formed. Subsequent heating of mechanically alloyed materials causes the activation of an exothermic reaction of Ti O2 reduction with aluminum, the start temperature of which, in the case of Cu addition,shifts to lower values, that is, the transformation begins in the solid state. Besides, the Cu-added material after laser melting demonstrates a more dispersed and uniform structure which positively affects its microhardness.
基金The authors are grateful for the financial supports from the National Natural Science Foundation of China(51804349)the China Postdoctoral Science Foundation(2018M632986)the Natural Science Foundation of Hunan Province,China(2019JJ50766).
文摘In-situ 2 vol.%TiB2 particle reinforced Al−xSi−0.3Mg(x=7,9,12,15 wt.%)composites were prepared by the salt−metal reaction,and the microstructures and mechanical properties were investigated.The results show that the TiB2 particles with a diameter of 20−80 nm and the eutectic Si with a length of 1−10μm are the main strengthening phases in the TiB2/Al−xSi−0.3Mg composites.The TiB2 particles promote grain refinement and modify the eutectic Si from needle-like to short-rod shape.However,the strengthening effect of TiB2 particles is weakened as the Si content exceeds the eutectic composition,which can be attributed to the formation of large and irregular primary Si.The axial tensile test results and fractography observations indicate that these composites show more brittle fracture characteristics than the corresponding alloy matrixes.
文摘Multi-wall carbon nanotubes (MWNTs) have high mechanical properties and are considered a kind of realistic reinforcement for polymers, ceramics and metals. The hot press sintering and squeeze casting were adopted to synthesize MWNTs reinforced aluminum composites. In hot press sintered MWNTs/Al composites, MWNTs agglomerates distribute along aluminum powders and have low bonding strength with aluminum. But MWNTs agglomerates distribute evenly in the squeeze cast MWNTs/Al composites. Some dispersed nanotubes bond well with aluminum matrix and few dislocations can be found in the nanotube areas, which implies little thermal residual stress in squeeze cast MWNTs/Al composites. This indicates that the strengthen mechanisms in nanometer sized MWNTs/Al composites may be different from that in micrometer sized whisker composites.
