Effect of Heat Treatment on Microstructure and Mechanical Properties of Multiscale SiC_p Hybrid Reinforced 6061 Aluminum Matrix Composites

The performance of solid solution aging treatment on aluminum matrix composites prepared by powder metallurgy and reinforced with 6061 aluminum alloy powder as matrix;meanwhile, nano silicon carbide particles(nm Si Cp), submicron silicon carbide particles(1 μm Si Cp) and Ti particles were studied. The Al/Si Cp composite powder was prepared by high-energy ball milling, and then cold-pressed, sintered, hotextruded, and then heat-treated with different solution temperatures and aging times for the extruded composites. Optical microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy(EDS), X-ray diffractometer(XRD) and extrusion testing were used to analyze and test the microstructure and mechanical properties of aluminum matrix composites. The results show that after the multi-stage solid solution at 530 ℃×2 h+535 ℃×2 h+540 ℃×2 h, the particles are mainly equiaxed grains and uniformly distributed. There is no reinforcement agglomeration, and the surface is dense and the insoluble phase is basically dissolved. In the matrix, the strengthening effect is good, and the hardness and compressive strength are 179.43 HV and 680.42 MPa, respectively. Under this solution process, when the aluminum matrix composites are aged at 170 ℃ for 10 h, the hardness and compressive strength can reach their peaks and increase to 195.82 HV and 721.48 MPa, respectively.

Investigation on the ballistic performance of the aluminum matrix composite armor with ceramic balls reinforcement under high velocity impact

In this research, the ballistic behavior of the ceramic-reinforced aluminum matrix composite plates is investigated to provide an optimal design for protecting against 7.62 mm bullet at the speed of 800 m/s experimentally and numerically. The target materials are Al5083 alloy as the metal matrix and alumina ceramic balls as the reinforcement. To simulate a 3D numerical model, ABAQUS FE code has been utilized.After validation the numerical model by experiments, the effect of ceramic ball weight percentage include 15%, 30% and 45% and the target thickness 20, 25 and 30 mm is considered on the ballistic results like the kinetic energy, residual velocity and depth of penetration. Finally, it was found that the specimen with 25 mm thickness and 30% alumina is optimum based on existing ballistic protection criteria.

In-situ fabrication of particulate reinforced aluminum matrix composites under high-frequency pulsed electromagnetic field

Pulsed magnetic field is generated when imposing pulse signal on high-frequency magnetic field. Distribution of the inner magnetic intensity in induction coils tends to be uniform. Furthermore oscillation and disturbance phenomena appear in the melt. In. situ Al2O3 and Al3Zr particulate reinforced aluminum matrix composites have been synthesized by direct melt reaction using AlZr（CO3）2 components under a foreign field. The size of reinforced particulates is 2-3 μm. They are well distributed in the matrix. Thermodynamic and kinetic analysis show that high-frequency pulsed magnetic field accelerates heat and mass transfer processes and improves the kinetic condition of in-situ fabrication.

Microstructure and Tensile Properties of Yttria Coated-Alumina Particulates Reinforced Aluminum Matrix Composites

The liquid-phase coating method was used to deposit Y2O3 ceramic on the surface of α-Al2O3. The coated-Al2O3p/6061AI composites were produced using squeeze casting technology. The microstructure and tensile properties of the composites were analysed and studied. The results showed that the coated AI2O3 particles are able to disperse homogeneously in the aluminum liquid. The microstructure of the composites is more even in comparison with that of as-received powders. The tensile testing indicated that mechanical properties of the coated-AI2O3p/6061AI composites are better than those of uncoated particles. In the composite with 30% volume fraction, the tensile strength, yield strength as well as elongation is increased by 29.8%, 38.4% and 10.3%, respectively. The SEM analysis of fracture indicated that the dimples of the coated-Al2O3p/6061Al composites are more even.

Aluminum matrix composites reinforced by molybdenum-coated carbon nanotubes

To extend the application of carbon nanotubes （CNTs） and explore novel aluminum matrix composites,CNTs were coated by molybdenum layers using metal organic chemical vapor deposition,and then Mo-coated CNT （Mo-CNT）/Al composites were prepared by the combination processes of powder mixing and spark plasma sintering.The influences of powder mixing and Mo-CNT content on the mechanical properties and electrical conductivity of the composites were investigated.The results show that magnetic stirring is better than mechanical milling for mixing the Mo-CNTs and Al powders.The electrical conductivity of the composites decreases with increasing Mo-CNT content.When the Mo-CNT content is 0.5wt%,the tensile strength and hardness of Mo-CNT/Al reach their maximum values.The tensile strength of 0.5wt% Mo-CNT/Al increases by 29.9%,while the electrical conductivity only decreases by 7.1%,relative to sintered pure Al.The phase analysis of Mo-CNT/Al composites reveals that there is no formation of Al carbide in the composites.

Microstructure and properties of mechanical alloying particles reinforced aluminum matrix composites prepared by semisolid stirring pouring method

Aluminum matrix composites reinforced with mechanical alloying particles(SiC_p) were fabricated by the semisolid stirring pouring method. The inf luence of mechanical alloying particles and Mg on the microstructure and mechanical properties of the composites was investigated by means of optical microscopy(OM), X-ray diffraction scanning(XRD), electron microscopy(SEM) and energy dispersive spectroscopy(EDS). Results show that the addition of Mg converts the agglomerate mechanical al oying particles in ZL101 matrix composites into dispersed distribution in ZL101-Mg matrix composites, large matrix grains into f ine equiaxed matrix grains, and eutectic phase into f ine particles. So the mechanical properties of ZL101-Mg matrix composites are better than those of ZL101 matrix composites. The mechanical properties of ZL101/ZL101-Mg matrix composites are gradually increased with the increase of the volume fraction of mechanical alloying particles. When the volume fraction of mechanical alloying particles is 3%, the Vickers hardness and ultimate tensile strength of the ZL101/ZL101-Mg matrix composites reach their maximum values.

The Role of Ti in the Preparation of SiC/7075 Aluminum Matrix Composite

SiC/7075 aluminum matrix composites were prepared by a liquid stirring method.The role of Ti facilitating the preparation of SiC/7075 aluminum matrix were studied by means of direct-reading spectrometer,scanning electron microscope,energy dispersive spectrometer,X-ray diffraction and the sessile drop method.The results show that the SiC content in the SiC/7075 composite increases with an increase of Ti addition.The addition of Ti can significantly improve the wettability of SiC/Al system,there is a critical value of above 0.5%of Ti content in improving the wettability of the Al/SiC system at 1173K.The temperature of the"non wetting-wetting"transition for the(Al-2Ti)/SiC system is about 1123K,the contact angle decreases to 88°at 200 seconds and reaches a stable contact angle of 28°at 2100 seconds.

Microstructure and Strength of Laser Welds of Sub-micron Particulate-reinforced Aluminum Matrix Composite Al_2O_(3p)/6061Al

The microstructure of laser welds of sub-micron particulate-reinforced aluminum matrix composite Al_2O_(3p)/6061Al and the weldability of the material were studied. Experimental results indicated that because of the huge specific surface area of the reinforcement, the interfacial reaction between the matrix and the reinforcement was re- strained intenslvely at elevated temperature and pulsed laser beam. The main factor affecting the weldability of the com- posite was the reinforcement segregation in the weld resulting from the push of the liquid/solid interface during the soli- dification of the molten pool. The laser pulse frequency directly affected the reinforcement segregation and the reinfor- cement distribution in the weld, so that the weldability of the composite could be improved by increasing the laser pulse frequency. On the basis of this, a satisfactory welded joint of sub-micron paniculate-reinforced aluminum matrix com- posite Al_2O_(3p)/6061Al was obtained by using appopriate welding parameters.

Mechanical Properties of Laser Welded Joints of High Volume Fraction SiCp/Al Aluminum Matrix Composite

High volume fraction SiCp/Al aluminum matrix composite possesses a variety of outstanding properties,such as high thermal conductivity and low coefficient of thermal expansion.It is widely applied in many fields,especially in automotive and aerospace.An orthogonal experiment is conducted to study the effects of relevant parameters on the mechanical properties by CO2 laser.Then the micro-hardness in different regions is measured.The effects of such parameters as laser power,middle layer thickness and welding speed on the tensile strength of the welded joints are discussed.The experimental results indicate that the maximum of the tensile strength of the welded joints is attained at the laser power of 1 200 W,the welding speed of 1.5 m/min and the middle layer thickness of 0.3 mm.In addition,the mechanism of the improvement of micro-hardness on the weld bead is also analyzed.

Effect of Heat Treatment on Microstructure and Mechanical Properties of Si Cp/2024 Aluminum Matrix Composite

SiCp/2024 aluminum alloy matrix composite was prepared by powder metallurgy method. Effects of heat treatment on the microstructure and mechanical properties of composite were investigated by SEM, EDS, XRD, HREM, tensile and hardness tests. The experimental results showed that SiC particles distributed uniformly in the matrix and were in good combination with matrix. The tensile strength and hardness were improved significantly after heat treatment. With the increase of solid solution temperature, the alloy phases dissolved in the matrix gradually. When the solid solution temperature arrived at 505 ℃, the alloy phases dissolved thoroughly, and the composite exhibited the highest tensile strength and hardness（σb=360 MPa, HBS=104）. The main strengthening phase was Al2Cu, which was granular and distributed dispersively in the matrix. Effect of T6 was better than that of T4 at the same solid solution temperature.

Damping capacity of amorphous carbon fiber/aluminum matrix composites at room temperature

The influence of volume fraction on damping capacities at room temperature for amorphous carbon fiber reinforced aluminum matrix composites was investigated.At room temperature,the dislocation damping is the primary damping mechanism.Meanwhile,the dislocation damping exhibits dynamic hysteresis at low strain amplitudes and static hysteresis at high strain amplitudes.Moreover,the damping capacity is rather sensitive to the volume fraction.Compared to unreinforced aluminum alloy,the additions of amorphous carbon fibers into the aluminum matrix can improve damping capacity below the volume fraction of 30%,whereas worsen above the volume fraction of 40%.

Research Status and Application Prospect of Aluminum Matrix Composites

Aluminum matrix composite is one of the most attractive metal matrix composites.It is a kind of material with strong vitality emerging in response to the needs of modern scientific development.Compared with traditional materials,aluminum matrix composites have the advantages of low density,good electric conductivity and heat conductivity,good wear resistance and oxidation resistance,high specific strength and stiffness,high temperature resistance,good heat treatment performance and flexible preparation process,which make them widely used in the fields of aviation,aerospace,and automobile.In this paper,the factors affecting the properties of aluminum matrix composites,the strengthening mechanism,classification and preparation methods of aluminum matrix composites are summarized.The research status,development direction and application prospect of aluminum matrix composites are briefly introduced.

Formation of interfacial Al-Ce-Cu-W amorphous layers in aluminum matrix composite through thermally driven solid-state amorphization

Interfacial Al-Ce-Cu-W amorphous layers formed through thermally driven solid-state amorphization within the(W+Ce O2)/2024 Al composite were investigated.The elemental distributions and interfacial microstructures were examined with an electron probe microanalyzer and a high-resolution transmission electron microscope,respectively.The consolidation of composites consisted of two thermal processes:vacuum degassing(VD)and hot isostatic pressing(HIP).During consolidation,not only the three major elements(Al,W,and Ce)but also the alloying elements(Mg and Cu)in the Al matrix contributed to amorphization.At VD and HIP temperatures of 723 K and763 K,interfacial amorphous layers were formed within the composite.Three diffusion processes were necessary for interfacial amorphization:(a)long-range diffusion of Mg from the Al matrix to the interfaces during VD;(b)long-range diffusion of Cu from the Al matrix to the interfaces during HIP;(c)short-range diffusion of W toward the Al matrix during HIP.The newly formed interfacial Al-Ce-Cu-W amorphous layers can be categorized under the Al-Ce-TM(TM:transition metals)amorphous system.

A High-Fe Aluminum Matrix Welding Filler Metal for Hardfacing Aluminum-Silicon Alloys

A high Fe containing aluminum matrix filler metal for hardfacing aluminum silicon alloys has been developed by using iron,nickel,and silicon as the major strengthening elements,and by measuring mechanical properties,room temperature and high temperature wear tests,and microstructural analysis.The filler metal,which contains 3.0%-5.0% Fe and 11.0%-13.0% Si,exhibits an excellent weldability.The as cast and as welded microstructures for the filler metal are of uniformly distribution and its dispersed network of hard phase is enriched with Al Si Fe Ni.The filler metal shows high mechanical properties and wear resistance at both room temperature and high temperatures.The deposited metal has a better resistance to impact wear at 220℃ than that of substrate Al Si Mg Cu piston alloy;at room temperature,the deposited metal has an equivalent resistance to slide wear with lubrication as that of a hyper eutectic aluminum silicon alloy with 27% Si and 1% Ni.

3D printed aluminum matrix composites with well-defined ordered structures of shear-induced aligned carbon fibers

Carbon fiber reinforced aluminum composites with ordered architectures of shear-induced aligned carbon fibers were fabricated by 3D printing.The microstructures of the printed and sintered samples and mechanical properties of the composites were investigated.Carbon fibers and aluminum powder were bonded together with resin.The spatial arrangement of the carbon fibers was fixed in the aluminum matrix by shear-induced alignment in the3D printing process.As a result,the elongation of the composites with a parallel arrangement of aligned fibers and the impact toughness of the composites with an orthogonal arrangement were 0.82%and 0.41 J/cm^(2),respectively,about 0.4 and 0.8 times higher than that of the random arrangement.

Interface and thermal expansion of carbon fiber reinforced aluminum matrix composites

Two kinds of unidirectional PAN M40 carbon fiber(55%,volume fraction) reinforced 6061Al and 5A06Al composites were fabricated by the squeeze-casting technology and their interface structure and thermal expansion properties were investigated.Results showed that the combination between aluminum alloy and fibers was well in two composites and interface reaction in M40/5A06Al composite was weaker than that in M40/6061Al composite.Coefficients of thermal expansion(CTE) of M40/Al composites varied approximately from(1.45-2.68)×10-6 K-1 to(0.35-1.44)×10-6 K-1 between 20 °C and 450 °C,and decreased slowly with the increase of temperature.In addition,the CTE of M40/6061Al composite was lower than that of M40/5A06Al composite.It was observed that fibers were protruded significantly from the matrix after thermal expansion,which demonstrated the existence of interface sliding between fiber and matrix during the thermal expansion.It was believed that weak interfacial reaction resulted in a higher CTE.It was found that the experimental CTEs were closer to the predicted values by Schapery model.

The Role of Particles in Fatigue Crack Propagation of Aluminum Matrix Composites and Casting Aluminum Alloys

疲劳裂缝繁殖( FCP )行为被学习原文如此理解 roleof 在 10 wt % SiCp/A2024 composites 的粒子和在扔铝 alloyA356.The 结果的 Si 粒子证明一些粒子在高三角洲 K 在 SiCp/Al compositeseven 出现在破裂表面上区域，它显示裂缝原文如此在 matrixavoiding 以内主要宣传了粒子由于粒子和强壮的 particle/matrixinterface.In 的高力量扔铝合金， Si

Effect of thermal-cooling cycle treatment on thermal expansion behavior of particulate reinforced aluminum matrix composites

Two micron SiC particles with angular and spherical shape and the sub-micron Al2O3 particles with spherical shape were introduced to reinforce 6061 aluminium by squeeze casting technology.Microstructures and effect of thermal-cooling cycle treatment(TCCT) on the thermal expansion behaviors of three composites were investigated.The results show that the composites are free of porosity and SiC/Al2O3 particles are distributed uniformly.Inflections at about 300 °C are observed in coefficient of thermal expansion(CTE) versus temperature curves of two SiCp/Al composites,and this characteristic is not affected by TCCT.The TCCT has significant effect on thermal expansion behavior of SiCp/Al composites and CTE of them after 3 cycles is lower than that of 1 or 5 cycles.However,no inflection is observed in Al2O3p/Al composite,while TCCT has effect on CTE of Al2O3p/Al composite.These results should be due to different relaxation behavior of internal stress in three composites.

Aluminum matrix composites reinforced by in situ Al_2O_3 and Al_3Zr particles fabricated via magnetochemistry reaction

Aluminum matrix composites reinforced by in situ Al2O3 and Al3Zr particles are fabricated from A356-Zr(CO3)2 system via magnetochemistry reaction,and the morphologies,sizes and distributions of the in situ particles as well as the microstructures,mechanical mechanisms of the composites are investigated by XRD,SEM,TEM and in situ tensile tests.The results indicate that with the pulsed magnetic field assistance,the morphologies of the in situ particles are mainly with ball-shape,the sizes are in nanometer scale and the distributions in the matrix are uniform.The interfaces between the in situ particles and the aluminum matrix are net and no interfacial outgrowth is observed.These are due to the strong vibration induced by the applied magnetic field in the aluminum melt,which in turn,accelerates the melt reactions.The effects of the magnetic field on the above contributions are discussed in detail.

On the liquid-phase technology of carbon fiber/aluminum matrix composites

The main problems with the liquid-phase technology of carbon fiber/aluminum matrix composites include poor wetting of the fiber with liquid aluminum and formation of aluminum carbide on the fibers’surface.This paper aims to solve these problems.The theoretical and experimental dependence of porosity on the applied pressure were determined.The possibility of obtaining a carbon fiber/aluminum matrix composite wire with a strength value of about 1500 MPa was shown.The correlation among the strength of the carbon fiber reinforced aluminum matrix composite,the fracture surface,and the degradation of the carbon fiber surface was discussed.