Microstructure characteristics and corrosion behavior of metal inert gas welded dissimilar joints of 6005A modified by Sc and 5083 alloys

The corrosion behavior and microstructure characteristics of metal inert gas(MIG)welded dissimilar joints of the 6005A alloy modified with Sc(designated as 6005A+Sc)and the 5083 alloy were investigated using corrosion tests and microscopy techniques.Results show that the dissimilar joints exhibit strong stress corrosion cracking(SCC)resistance,maintaining substantial strength during slow strain rate tensile tests.Notably,the heat-affected zone(HAZ)and base metal(BM)on the 6005A+Sc side show superior performance in terms of inter-granular corrosion(IGC)and exfoliation corrosion(EXCO)compared to the corresponding zones on the 5083 side.The lower corrosion resistance of the 5083-BM and the 5083-HAZ can be attributed to the presence of numerous Al_(2)Mg_(3)phases and micro-scaled Al_(6)(Mn,Fe)intermetallics,mainly distributed along the rolling direction.Conversely,the enhanced corrosion resistance of the 6005A+Sc-BM and the 6005A+Sc-HAZ can be attributed to the discontinuously distributed grain boundary precipitates(β-Mg_(2)Si),the smaller grain size,and the reduced corrosive current density.

Microstructure and thermal properties of dissimilar M300–CuCr1Zr alloys by multi-material laser-based powder bed fusion

Multi-material laser-based powder bed fusion (PBF-LB) allows manufacturing of parts with 3-dimensional gradient and additional functionality in a single step. This research focuses on the combination of thermally-conductive CuCr1Zr with hard M300 tool steel.Two interface configurations of M300 on CuCr1Zr and CuCr1Zr on M300 were investigated. Ultra-fine grains form at the interface due to the low mutual solubility of Cu and steel. The material mixing zone size is dependent on the configurations and tunable in the range of0.1–0.3 mm by introducing a separate set of parameters for the interface layers. Microcracks and pores mainly occur in the transition zone.Regardless of these defects, the thermal diffusivity of bimetallic parts with 50vol% of CuCr1Zr significantly increases by 70%–150%compared to pure M300. The thermal diffusivity of CuCr1Zr and the hardness of M300 steel can be enhanced simultaneously by applying the aging heat treatment.

Interface characteristic of friction stir welding lap joints of Ti/Al dissimilar alloys

Lap joints of TC1 Ti alloy and LF6 A1 alloy dissimilar materials were fabricated by friction stir welding and corresponding interface characteristics were investigated. Using the selected welding parameters, excellent surface appearance forms, but the interface macrograph for each lap joint cross-section is different. With the increase of welding speed or the decrease of tool rotation rate, the amount of Ti alloy particles stirred into the stir zone by the force of tool pin decreases continuously. Moreover, the failure loads of the lap joints also decrease with increasing welding speed and the largest value is achieved at welding speed of 60 mm/min and tool rotation rate of 1500 r/min, where the interracial zone can be divided into 3 kinds of layers. The microhardness of the lap joint shows an uneven distribution and the maximum hardness of HV 502 is found in the middle of the stir zone.

Effect of intermetallic compounds on the fracture behavior of dissimilar friction stir welding joints of Mg and Al alloys

Joining Mg to Al is challenging because of the deterioration of mechanical properties caused by the formation of intermetallic compounds(IMCs) at the Mg/Al interface. This study aims to improve the mechanical properties of welded samples by preventing the fracture location at the Mg/Al interface. Friction stir welding was performed to join Mg to Al at different rotational and travel speeds. The microstructure of the welded samples showed the IMCs layers containing Al12Mg17(γ) and Al3Mg2(β) at the welding zone with a thickness(< 3.5 μm). Mechanical properties were mainly affected by the thickness of the IMCs, which was governed by welding parameters. The highest tensile strength was obtained at 600 r/min and 40 mm/min with a welding efficiency of 80%. The specimens could fracture along the boundary at the thermo-mechanically affected zone in the Mg side of the welded joint.

Electrochemical corrosion behaviour of stir zone of friction stir welded dissimilar joints of AA6061 aluminium-AZ31B magnesium alloys

Joining of dissimilar metals will offer many advantages in transportation sectors such as fuel consumption,weightreduction and emission reduction.However,joining of aluminium(Al)alloys with magnesium(Mg)alloys by fusion welding processis very complicated.Friction stir welding(FSW)is a feasible method to join these two dissimilar alloys.Mixing these two metalstogether in stir zone(SZ)leads to poor corrosion resistance.In this investigation,an attempt has been made to understand thecorrosion resistance of SZ of FSWed dissimilar joints of AA6061Al alloy and AZ31B Mg alloy.Potentiodynamic polarization testwas conducted by varying chloride ion concentration,pH value of the NaCl solution and exposure time.The corroded surfaces wereanalyzed using optical microscopy,scanning electron microscopy and XRD techniques.Of these three factors investigated,exposuretime is found to be the most significant factor to influence the corrosion behaviour of SZ of friction stir welded dissimilar joints ofAl/Mg alloys.

Optimization of process parameters to maximize ultimate tensile strength of friction stir welded dissimilar aluminum alloys using response surface methodology

Aluminium alloys generally present low weldability by traditional fusion welding process. Development of the friction stir welding （FSW） has provided an alternative improved way of producing aluminium joints in a faster and reliable manner. The quality of a weld joint is stalwartly influenced by process parameter used during welding. An approach to develop a mathematical model was studied for predicting and optimizing the process parameters of dissimilar aluminum alloy （AA6351 T6-AA5083 Hlll）joints by incorporating the FSW process parameters such as tool pin profile, tool rotational speed welding speed and axial force. The effects of the FSW process parameters on the ultimate tensile strength （UTS） of friction welded dissimilar joints were discussed. Optimization was carried out to maximize the UTS using response surface methodology （RSM） and the identified optimum FSW welding parameters were reported.

Corrosion behavior and mechanical properties of cold metal transfer welded dissimilar AA7075-AA5754 alloys

Cold metal transfer(CMT) welding is a brand-new arc welding technique which shows adequate results for welding of thin sheets and dissimilar materials. Corrosion behavior of dissimilar aluminum joints should be determined in terms of predicting the effect of welding process on the possible failures in their constructions caused by corrosive agents. The present study investigates the effect of heat input on mechanical properties and corrosion rate of AA5754-AA7075 joints welded by CMT using ER5356 filler wire. Pore formation was observed not only in the weld metal but also in the partially melted zone of AA7075 base metal due to the vaporization of zinc. Increased heat input caused over aging and zinc vaporization in AA7075 base metal, and grain coarsening in AA5754 base metal consequently decreased the tensile strength. The average tensile strength of AA7075-AA5754 joints varies between 235 and 240 MPa. The ductile fracture occurred at the AA5754 base metal side in all samples. Pitting was observed as the dominant corrosion mechanism. Corrosion resistance tended to increase with increasing heat input. Heat input values between 95 and 110 J/mm are recommended for the optimization of corrosion resistance and strength.

Material properties of friction stir spot welded joints of dissimilar aluminum alloys

Mechanical properties and material mixing patterns of friction stir spot welded (FSSW) joints of dissimilar aluminum alloys were investigated.Two aluminum alloys typically used in automotive applications,5052-H32 and 6061-T6,were selected.During the experiment,the process parameters including the z-axis force and torque histories were measured as a function of the tool displacement.The mechanical properties were investigated by microhardness measurements of the joint,and the material mixing in the stir zone was investigated by EPMA.The experimental results illustrate different process parameter histories,material mixing in the stir zone and material properties including microhardness distributions for FSSW joints of dissimilar aluminum alloys,likely due to different mechanical behaviors of the selected aluminum alloys in the FSSW process temperature range.

Numerical simulation and experimental study of hybrid laser-electric arc welding between dissimilar Mg alloys

This work aims to establish a suitable numerical simulation model for hybrid laser-electric arc heat source welding of dissimilar Mg alloys between AZ31 and AZ80. Based on the energy conservation law and Fourier’s law of heat conduction, the differential equations of the three-dimensional temperature field for nonlinear transient heat conduction are built. According to the analysis of nonlinear transient heat transfer, the equations representing initial conditions and boundary conditions are obtained. The “double ellipsoidal heat source + 3D Gaussian heat source”combination was chosen to construct the laser-electric arc hybrid heat source. The weld bead morphologies and the distribution of temperature, stress, displacement and plastic strains are numerically simulated. The actual welding experiments were performed by a hybrid laser-electric arc welding machine. The interaction mechanism between laser and electric arc in the hybrid welding of Mg alloys is discussed in detail. The hybrid heat source can promote the absorption of laser energy and electric arc in the molten pool, resulting in more uniform energy distribution in the molten pool and the corresponding improvement of welding parameters. This work can provide theoretical guidance and data supports for the optimization of the hybrid laser-electric arc welding processes for Mg alloys.

Friction Stir Welding of Dissimilar Aluminum Alloys

Dissimilar aluminum alloys AA2024-T365 and AA5083-H111 were welded by friction stir process. Welding parameters such as tool rotational speed (900, 1120 and 1400 rpm), weld speeds (16, 40 and 80 mm/min) and tool pin profiles (square, triangular and stepped) were used to weld many joints to study their effect on the mechanical properties of the joint. Also, different locations of the material were studied as other parameter. The mechanical properties were evaluated using tensile and hardness tests. The microstructure characterization of the processed alloys was carried out using optical microscopy. Macro and microstructures of parent and welded specimens indicated that the weld parameters have a significant effect on mechanical and microstructural properties of the welds. However, defect-free as well as higher strength was obtained at higher speed of 80 mm/min.

Microstructure and mechanical properties of dissimilar Al-Cu joints by friction stir welding

Dissimilar friction stir welding between 1060 aluminum alloy and annealed pure copper sheet with a thickness of 3 mm was investigated. Sound weld was obtained at a rotational speed of 1050 r/min and a welding speed of 30 mm/min. Intercalation structure formed at the crown and Cu/weld nugget （WN） area promotes interracial diffusion and metallurgical bonding of aluminum and copper. However, corrosion morphology reveals the weak bonding mechanism of internal interface, which causes the joint failing across the interface with a brittle-ductile mixed fracture mode. The tensile strength of the joint is 148 MPa, which is higher than that of the aluminum matrix. Crystal defects and grain refinement by severely plastic deformation during friction stir welding facilitate short circuit diffusion and thus accelerate the formation of A14Cu9 and A12Cu intermetallic compounds （IMCs）. XRD results show that A14Cu9 is mainly in Cu/WN transition zone. The high dislocation density and formation of dislocation loops are the major reasons of hardness increase in the WN.

搅拌摩擦焊在镁合金焊接中的应用与进展

近年来,镁合金在航空航天、汽车电子、轨道交通等领域的需求日益增长,焊接是保障镁合金工业化应用的重要技术手段。搅拌摩擦焊(FSW)因其绿色环保、焊接效率高、接头性能好等优势在镁合金焊接中得到了一定的应用。本文从工艺参数与性能、镁合金FSW辅助技术与异种镁合金FSW研究等对国内外镁合金FSW进行了归纳,并对镁合金FSW未来的发展进行了展望。

TiAl合金与45Cr9Si3马氏体钢异种材料电阻焊接头界面结构研究

TiAl合金和45Cr9Si3马氏体钢在发动机气门阀结构中具有潜在应用价值,但二者物理、化学性能差异较大,焊接存在较大的挑战。研究发现,采用电阻焊能够实现TiAl合金和45Cr9Si3马氏体钢的良好焊接,焊接接头中不存在明显的裂纹、气孔等缺陷。在TiAl合金与45Cr9Si3马氏体钢的焊接界面存在厚度为5μm左右的扩散反应层,该扩散反应层主要是45Cr9Si3马氏体钢中的Fe元素向TiAl合金一侧扩散形成的。在焊缝处存在局部液化区,主要是焊接初期焊接界面的不均匀接触导致接触尖点位置瞬间通过大电流而发生液化所引起的。

Microstructures and mechanical properties of metal inert-gas arc welded Mg-steel dissimilar joints

The joining of Mg alloy to steel was realized by metal inert-gas arc welding, and the weld thermal cycle characteristics and Mg-steel joints were investigated. The results show that the temperature distribution in the joints is uneven. Mg alloy welds present a fine equiaxed grain structure. There exists a transition layer consisting mainly of AlFe, AlFe3 and Mg（Fe, Al）2O4 phases at Mg/steel interface, and it is the weakest link in Mg？steel joints. The welding heat input and weld Al content have the significant effect on the joint strength. The joint strength increases with increasing the heat input from 1680 J/cm to 2093 J/cm, due to promoting Mg/steel interface reaction. When weld Al content is increased to 6.20%, the joint strength reaches 192 MPa, 80% of Mg alloy base metal strength. It is favorable to select the suitable welding heat input and weld Al content for improving joint strength.

Effect of welding process on the microstructure and properties of dissimilar weld joints between low alloy steel and duplex stainless steel

To obtain high-quality dissimilar weld joints, the processes of metal inert gas （MIG） welding and tungsten inert gas （TIG） welding for duplex stainless steel （DSS） and low alloy steel were compared in this paper. The microstructure and corrosion morphology of dissimilar weld joints were observed by scanning electron microscopy （SEM）; the chemical compositions in different zones were detected by en- ergy-dispersive spectroscopy （EDS）; the mechanical properties were measured by microhardness test, tensile test, and impact test; the corro- sion behavior was evaluated by polarization curves. Obvious concentration gradients of Ni and Cr exist between the fusion boundary and the type II boundary, where the hardness is much higher. The impact toughness of weld metal by MIG welding is higher than that by TIG weld- ing. The corrosion current density of TIG weld metal is higher than that of MIG weld metal in a 3.5wt% NaC1 solution. Galvanic corrosion happens between low alloy steel and weld metal, revealing the weakness of low alloy steel in industrial service. The quality of joints pro- duced by MIG welding is better than that by TIG welding in mechanical performance and corrosion resistance. MIG welding with the filler metal ER2009 is the suitable welding process for dissimilar metals jointing between UNS $31803 duplex stainless steel and low alloy steel in practical application.

Microstructures and properties analysis of dissimilar metal joint in the friction stir welded copper to aluminum alloy

This paper mainly concentrated on the feasibility of friction stir welding of dissimilar metal of aluminum alloy to copper （I2） and a preliminary analysis of welding parameters influencing on the microstructures and properties of joint was carried out. The results indicated that the thickness of workpiece played an important role in the welding parameters which could succeed in the friction stir welding of dissimilar metal of copper to aluminum alloy, and the parameters were proved to be a narrow choice. The interfacial region between copper and aluminum in the dissimilar joint was not uniformly mixed, constituted with part of incomplete mixing zone, complete mixing zone, dispersion zone and the most region＇ s boundary was obvious. Meantime a kind banded structure with inhomogeneous width was formed. The intermetallic compounds generated during friction stir welding in the interfacial region were mainly CugAl4, Al2Cu etc, and their hardness was higher than oihers.

Microstructure and mechanical properties of laser beam welded TC4/TA15 dissimilar joints

The microstructure and mechanical properties of laser beam welded dissimilar joints in TC4 and TA15 titanium alloyswere investigated. The results showed that the coarse columnar grains containing a large amount of acicular α and martensite α′ werepresent in the fusion zone (FZ), some residual α phases and martensite structure were formed in the heat-affected zone (HAZ) onTC4 side, and bulk equiaxed α phase of the HAZ was on TA15 side. An asymmetrical microhardness profile across the dissimilarjoint was observed with the highest microhardness in the FZ and the lowest microhardness in TA15 BM. The orders of yield strengthand ultimate tensile strength were as follows: TC4 BM > TC4/TC4 similar joint > TA15 BM > TA15/TA15 similar joint > TC4/TA15dissimilar joint, and increased while hardening capacity and strain hardening exponent decreased with increasing strain rate from1×10?4 s?1 to 1×10?2 s?1. The TC4/TA15 dissimilar joints failed in the TA15 BM, and had characteristics of ductile fracture atdifferent strain rates.

Microstructure and tensile properties of friction stir welded dissimilar AA6061-AA5086 aluminium alloy joints

The fusion welding of dissimilar heat treatable and non-heat treatable aluminium alloy faced many problems related to solidification. The difficulties can be overcome to achieve the combined beneficial properties of both aluminium alloys using friction stir welding(FSW). The microstructural features and tensile properties of friction stir welded(FSW) similar and dissimilar joints made of AA6061 and AA5086 aluminium alloys were investigated. The microstructures of various regions were observed and analyzed by means of optical and scanning electron microscopy. Microhardness was measured at various zones of the welded joints. The tensile properties of the joints were evaluated and correlated with the microstructural features and microhardness values. The dissimilar joint exhibits a maximum hardness of HV 115 and a joint efficiency of 56%. This was attributed to the defect free stir zone formation and grain size strengthening.

Microstructure and mechanical properties of friction stir weld of dissimilar AZ31-O magnesium alloy to 6061-T6 aluminum alloy

Dissimilar friction stir welding between AZ31-O Mg and 6061-T6 Al alloys was investigated. 3 mm thick plates of aluminum and magnesium were used. Friction stir welding operations were performed at different rotation and travel speeds. The rotation speeds varied from 600 to 1400 r/min, and the travel speed varied from 20 to 60 mm/min. Defect-free weld was obtained with a rotation speed of 1000 r/min and travel speed of 40 mm/min. Metallographic studies showed that the grain size in the stir zone is much finer than that in the base metals. Complex flow pattern was formed in the stir zone. Microhardness measurement revealed an uneven distribution in the stir zone. Tensile test results indicated that the tensile strength of the welded specimen is about 76% of AZ31 Mg alloy and 60% of the 6061 Al alloy in tensile strength. SEM fracture surface image of the welded specimen indicated that the welded specimen failed through brittle-mode fracture.

Effect of welding heat input and post-weld aging time on microstructure and mechanical properties in dissimilar friction stir welded AA7075-AA5086

The effects of welding heat input and post-weld heat treatment on the mechanical and microstructural aspects of dissimilarfriction stir welds of age-hardened AA7075-T6and strain hardenable AA5086-H32aluminium alloys were investigated.X-raydiffraction(XRD)residual stress analysis and tensile testing together with optical metallography and transmission electronmicroscopy(TEM)were performed to assess the effects of process parameters on welded joints.It was discovered that jointsproduced without heat sink exhibited more homogeneous stir zones than other joints.Of the natural aging time studied,higheramount of solid solution during rapid cooling of welds produced higher driving force for increase in hardness in the AA7075sideduring natural aging.Natural aging within stirring zone and thermo-mechanical affected zone of AA7075side resulted in a10to25MPa reduction in the residual stress in these zones;its effect decreased considerably in the welds performed without heat sink.Inaddition,natural aging had no noticeable effect on the joint strength.