We proposed a new way to synthesize a nanocomposite consisted of cementite Fe3C nanoparticles and amorphous carbon by radio frequency plasma-enhanced chemical vapor deposition. Transmission electron microscope images ...We proposed a new way to synthesize a nanocomposite consisted of cementite Fe3C nanoparticles and amorphous carbon by radio frequency plasma-enhanced chemical vapor deposition. Transmission electron microscope images show the existence of nanometric dark grains（Fe3C） embedded in a light matrix（amorphous carbon） in the samples. X-ray photoelectron spectroscopy experiment exhibit that the chemical bonding state in the films corresponded to sp3/sp2 amorphous carbon, sp^3 C-N（287.3 eV） and C15 in Fe3C（283.5 eV）. With increasing deposition time, the ratio of amorphous carbon increased. The magnetic measurements show that the value of in-lane coercivity increased with increasing carbon matrix concentration（from about 6.56× 10^3 A/m for film without carbon structures to approximately 2.77× 10^4 and 5.81 × 10^4 AJm for nanocomposite films at room temperature and 10 K, respectively）. The values of saturation magnetization for the synthesized nanocomposites were lower than that of the bulk Fe3C （ 140 Am^2/kg）.展开更多
By direct observations of transmission electron microscopy (TEM), irreversible morphological transformations of as-deposited amorphous Au/Si multilayer (a-Au/a-Si) were observed on heating. The well arrayed sequence o...By direct observations of transmission electron microscopy (TEM), irreversible morphological transformations of as-deposited amorphous Au/Si multilayer (a-Au/a-Si) were observed on heating. The well arrayed sequence of the multilayer changed to zigzag layered structure at 478 K (=Tzig). Finally, the zigzag structure transformed to Au nanoparticles at 508 K. The distribution of the Au nanoparticles was random within the thin film. In situ X-ray diffraction during heating can clarify partial crystallization Si (c-Si) in the multilayer at 450 K (= ), which corresponds to metal induced crystallization (MIC) from amorphous Si (a-Si) accompanying by Au diffusion. On further heating, a-Au started to crystallize at around 480 K (=Tc) and gradually grew up to 3.2 nm in radius, although the volume of c-Si was almost constant. Continuous heating caused crystal Au (c-Au) melting into liquid AuSi (l-AuSi) at 600 K (= ), which was lower than bulk eutectic temperature ( ). Due to the AuSi eutectic effect, reversible phase transition between liquid and solid occurred once temperature is larger than . Proportionally to the maximum temperatures at each cycles (673, 873 and 1073 K), both and Au crystallization temperature approaches to . Using a thermodynamic theory of the nanoparticle formation in the eutectic system, the relationship between and the nanoparticle size is explained.展开更多
The search for active,stable,and cost-effective electrocatalysts for hydrogen evolution reaction(HER)is desirable,but it remains a great challenge in the overall water splitting.Here,we report the synthesis of nickel ...The search for active,stable,and cost-effective electrocatalysts for hydrogen evolution reaction(HER)is desirable,but it remains a great challenge in the overall water splitting.Here,we report the synthesis of nickel boron nanoparticles supported on Vulcan carbon(Ni-B)via a simple,yet scalable,two-step chemical reduction–annealing strategy.The results of the electrochemical measurements suggest that the overpotentials of Ni-B-400 are 114 and 215 mV(in 1 mol L^–1 KOH)at current densities of 10 and 40 mA cm^?2,respectively,indicating an exceedingly good electrocatalytic activity in the HER.More importantly,Ni-B maintains a current density of 7.6 mA cm^-2 at an overpotential of 0.15 V for 20 h in the durability test.The excellent HER activity of Ni-B-400 is derived from the small particle size and the expanded lattice of Ni,which can optimize the hydrogen absorption energy and enhance the electrocatalytic properties.展开更多
A series of Ce-doped Ni-B amorphous alloy catalysts were prepared by a KBH_4 reduction method, characterized by ICP, BET, XRD, H_2-chemisorption, H_2-TPD, etc., and tested in the hydrogenation of 2-ethylanthraquinone....A series of Ce-doped Ni-B amorphous alloy catalysts were prepared by a KBH_4 reduction method, characterized by ICP, BET, XRD, H_2-chemisorption, H_2-TPD, etc., and tested in the hydrogenation of 2-ethylanthraquinone. The results of characterization show that with the addition of Ce the amount of H_2-chemisorption and H_2-TPD areas first increases markedly and then decreases with the maximum appears at the atomic ratio of Ce to Ni of 0.036. The hydrogenation activity also shows the same trend. The effects of Ce are attributed to its dispersion of Ni particles, resulting in the formation of more surface Ni centers. However, much higher Ce contents may result in the decrease of the surface Ni contents. After heat treatment at higher temperatures, the amorphous structure of Ni-B is destroyed.展开更多
A supported Ni-B/TiO2 amorphous catalyst was prepared by impregnation and reduction. It was characterized by XRD, SAED, DSC, XPS, etc.. The catalytic activity of catalyst was measured through the hydrogenation of he...A supported Ni-B/TiO2 amorphous catalyst was prepared by impregnation and reduction. It was characterized by XRD, SAED, DSC, XPS, etc.. The catalytic activity of catalyst was measured through the hydrogenation of heavy arenes in petrochemicals for the first time.展开更多
Uniform Ni-B amorphous alloys about 14 nm have been prepared on CNTs-A support,named Ni-B/CNTs-A. In comparison with the Ni-B/CNTs amorphous catalyst, Ni-B/CNTs-A showed higher nickel loading, determined by ICP and be...Uniform Ni-B amorphous alloys about 14 nm have been prepared on CNTs-A support,named Ni-B/CNTs-A. In comparison with the Ni-B/CNTs amorphous catalyst, Ni-B/CNTs-A showed higher nickel loading, determined by ICP and better catalytic activity and ethylene selectivity in the acetylene hydrogenation reaction.展开更多
The influence of emissions of an active volcano on the composition of nanoparticles and ultrafine road dust was identified in an urban area of the Andes.Although many cities are close to active volcanoes,few studies h...The influence of emissions of an active volcano on the composition of nanoparticles and ultrafine road dust was identified in an urban area of the Andes.Although many cities are close to active volcanoes,few studies have evaluated their influence in road dust composition.Air quality in urban areas is significantly affected by nonexhaust emissions(e.g.road dust,brake wear,tire wear),however,natural sources such as volcanoes also impact the chemical composition of the particles.In this study,elements from volcanic emissions such as Si>Al>Fe>Ca>K>Mg,and Si-Al with K were identified as complex hydrates.Similarly,As,Hg,Cd,Pb,As,H,Cd,Pb,V,and salammoniac were observed in nanoparticles and ultrafine material.Mineral composition was detected in the order of quartz>mullite>calcite>kaolinite>illite>goethite>magnetite>zircon>monazite,in addition to salammoniac,a tracer of volcanic sources.The foregoing analysis reflects the importance of carrying out more studies relating the influence of volcanic emissions in road dust in order to protect human health.The road dust load(RD_(10))ranged between 0.8 and 26.8 mg m^(−2)in the city.展开更多
The molecular dynamics(MD)simulations were used to understand the heat transfer process between the gas phase and the solid skeleton in the nanoporous silica aerogels.The amorphous silica nanoparticles were generated ...The molecular dynamics(MD)simulations were used to understand the heat transfer process between the gas phase and the solid skeleton in the nanoporous silica aerogels.The amorphous silica nanoparticles were generated by the MD simulations and the energy accommodation coefficient(EAC)between the gases and the nanoparticles was calculated based on the results of the nonequilibrium molecular dynamics(NEMD)simulations.The apparent thermal conductivity(ATC)of the gases between the heat source and heat sink was also obtained.The effects of the temperature,the particle diameter and the molecule type on the EAC and the ATC were investigated.The results indicate that the EAC decreases with the increase of temperature within the calculating range.When the preset temperature is constant,the EAC increases with the increasing of the particle diameter and eventually approaches a specific value.When the preset temperature is 300 K and the particle size is 4 nm,the obtained EAC for the N2 gas and the O2 gas is close to each other and both are less than that of the Ar gas.The results also indicate that the heat transferred through the gas-nanoparticle interface is far less than that through the neighbouring nanoparticles in silica aerogels.展开更多
Recently,multifunctional nanoparticles have shown great prospects in cancer treatment,which have the ability to simultaneously deliver the drug,image and target tumor cells.In this paper,we designed a luminescent nano...Recently,multifunctional nanoparticles have shown great prospects in cancer treatment,which have the ability to simultaneously deliver the drug,image and target tumor cells.In this paper,we designed a luminescent nanoparticles platform based on hydrothermal hyaluronic acid/amorphous calcium phosphate(HA-FCNs/ACP)with multifunctional properties for drug delivery,bio-imaging,and targeting treatment.HA-FCNs/ACP shows an ability to load curcumin(Cur)with pH-sensitive responsive drug release behavior and excellent biocompatibility.HA-FCNs/ACP dispersed in the cytoplasm through the overexpressed CD44 receptor that is actively targeted into human lung cancer cells(A549 cells).Meanwhile,the viability of A549 cells was significantly inhibited in vitro.The prepared HA-FCNs and HA-FCNs/ACP both exhibit excellent targeted bioimaging performance on cancer cells.Hence,the as-prepared nanoparticles have promising applications in treating tumor disease.展开更多
Smart nanoparticles that respond to pathophysiological parameters,such as p H,GSH,and H2O2,have been developed with the huge and urgent demand for the high-efficient drug delivery systems(DDS)for cancer therapy.Herein...Smart nanoparticles that respond to pathophysiological parameters,such as p H,GSH,and H2O2,have been developed with the huge and urgent demand for the high-efficient drug delivery systems(DDS)for cancer therapy.Herein,cubic poly(ethylene glycol)(PEG)-modified mesoporous amorphous iron oxide(AFe)nanoparticles(AFe-PEG)have been successfully prepared as p H-stimulated drug carriers,which can combine doxorubicin(DOX)with a high loading capacity of 948 mg/g,forming a novel multifunctional AFe-PEG/DOX nanoparticulate DDS.In an acidic microenvironment,the AFe-PEG/DOX nanoparticles will not only release DOX efficiently,but also release Fe ions to catalyze the transformation of H2O2 to·OH,acting as fenton reagents.In vitro experimental results proved that the AFe-PEG/DOX nanoparticles can achieve combination of chemotherapeutic(CTT)and chemodynamic therapeutic(CDT)effects on Hela tumor cells.Furthermore,the intrinsic magnetism of AFePEG/DOX makes its cellular internalization efficiency be improved under an external magnetic field.Therefore,this work develops a new and promising magnetically targeted delivery and dual CTT/CDT therapeutic nano-medicine platform based on amorphous iron oxide.展开更多
Calcium-based biomaterials have been intensively studied in the field of drug delivery owing to their excellent biocompatibility and biodegradability.Calcium-based materials can also deliver contrast agents,which can ...Calcium-based biomaterials have been intensively studied in the field of drug delivery owing to their excellent biocompatibility and biodegradability.Calcium-based materials can also deliver contrast agents,which can enhance real-time imaging and exert a Ca^(2+)-interfering therapeutic effect.Based on these characteristics,amorphous calcium carbonate(ACC),as a brunch of calcium-based biomaterials,has the potential to become a widely used biomaterial.Highly functional ACC can be either discovered in natural organisms or obtained by chemical synthesis However,the standalone presence of ACC is unstable in vivo.Additives are required to be used as stabilizers or core-shell structures formed by permeable layers or lipids with modified molecules constructed to maintain the stability of ACC until the ACC carrier reaches its destination.ACC has high chemical instability and can produce biocompatible products when exposed to an acidic condition in vivo,such as Ca^(2+) with an immune-regulating ability and CO_(2) with an imaging-enhancing ability.Owing to these characteristics,ACC has been studied for selfsacrificing templates of carrier construction,targeted delivery of oncology drugs,immunomodulation,tumor imaging,tissue engineering,and calcium supplementation.Emphasis in this paper has been placed on the origin,structural features,and multiple applications of ACC.Meanwhile,ACC faces many challenges in clinical translation,and long-term basic research is required to overcome these challenges.We hope that this study will contribute to future innovative research on ACC.展开更多
Although much effort has been focused on the preparation of stable amorphous calcium phosphate （ACP） nanoparticles in aqueous solution, the redispersibility and long-term stability of ACP nanoparticles in aqueous so...Although much effort has been focused on the preparation of stable amorphous calcium phosphate （ACP） nanoparticles in aqueous solution, the redispersibility and long-term stability of ACP nanoparticles in aqueous solution remains an unresolved problem. In this work, stable colloidal ACPs were prepared by using an organic bisphosphonate （BP） as a sterically hindered agent in aqueous solution. The harvested calcium phosphate nanoparticles were characterized by inductively coupled plasma atomic emission spectrometry （ICP-AES）, Fourier transform infrared （FTIR）, X-ray diffraction （XRD）, dynamic light scattering （DLS） and transmission electron microscopy （TEM）. ICP-AES, FTIR and XRD results suggested the particles were ACP. DLS and TEM results indicated that the size of the ACP nanoparticles were in the range of 60 nm with a spherical morphology. The resulting calcium phosphate nanoparticles retained its amorphous nature in aqueous solution for at least 6 months at room temperature due to the stabilizing effect of the organic bisphosphonate. Moreover, the surface of the ACP nanoparticles adsorbed with the organic bisphosphate used showed good redispersibility and high colloid stability both in organic and aqueous solutions.展开更多
The main drawbacks of vanadium oxide as a cathode material are its low conductivity, low practical capacity and poor cycling stability. Adding Cr can improve its conductivity and a metastable amorphous state may provi...The main drawbacks of vanadium oxide as a cathode material are its low conductivity, low practical capacity and poor cycling stability. Adding Cr can improve its conductivity and a metastable amorphous state may provide higher capacity and stability. In this work, metastable amorphous Cr-V-O nano- particles have been successfully prepared through a facile co-precipitation reaction followed by annealing treatment. As a cathode material for lithium batteries, the metastable amorphous Cr-V-O nanoparticles exhibit high capacity （260 mAh/g at 100 mA/g between 1.5-4 V）, low capacity loss （more than 80% was retained after 200 cycles at 100 mA/g） and high rate capability （up to 3 A/g）.展开更多
基金Supported by the National Natural Science Foundation of China(No.50832001)the Science and Technology Develop-ment Program of Jilin Province, China(No.20070501)
文摘We proposed a new way to synthesize a nanocomposite consisted of cementite Fe3C nanoparticles and amorphous carbon by radio frequency plasma-enhanced chemical vapor deposition. Transmission electron microscope images show the existence of nanometric dark grains（Fe3C） embedded in a light matrix（amorphous carbon） in the samples. X-ray photoelectron spectroscopy experiment exhibit that the chemical bonding state in the films corresponded to sp3/sp2 amorphous carbon, sp^3 C-N（287.3 eV） and C15 in Fe3C（283.5 eV）. With increasing deposition time, the ratio of amorphous carbon increased. The magnetic measurements show that the value of in-lane coercivity increased with increasing carbon matrix concentration（from about 6.56× 10^3 A/m for film without carbon structures to approximately 2.77× 10^4 and 5.81 × 10^4 AJm for nanocomposite films at room temperature and 10 K, respectively）. The values of saturation magnetization for the synthesized nanocomposites were lower than that of the bulk Fe3C （ 140 Am^2/kg）.
文摘By direct observations of transmission electron microscopy (TEM), irreversible morphological transformations of as-deposited amorphous Au/Si multilayer (a-Au/a-Si) were observed on heating. The well arrayed sequence of the multilayer changed to zigzag layered structure at 478 K (=Tzig). Finally, the zigzag structure transformed to Au nanoparticles at 508 K. The distribution of the Au nanoparticles was random within the thin film. In situ X-ray diffraction during heating can clarify partial crystallization Si (c-Si) in the multilayer at 450 K (= ), which corresponds to metal induced crystallization (MIC) from amorphous Si (a-Si) accompanying by Au diffusion. On further heating, a-Au started to crystallize at around 480 K (=Tc) and gradually grew up to 3.2 nm in radius, although the volume of c-Si was almost constant. Continuous heating caused crystal Au (c-Au) melting into liquid AuSi (l-AuSi) at 600 K (= ), which was lower than bulk eutectic temperature ( ). Due to the AuSi eutectic effect, reversible phase transition between liquid and solid occurred once temperature is larger than . Proportionally to the maximum temperatures at each cycles (673, 873 and 1073 K), both and Au crystallization temperature approaches to . Using a thermodynamic theory of the nanoparticle formation in the eutectic system, the relationship between and the nanoparticle size is explained.
基金supported by the National Natural Science Foundation of China(21573083)the 1000 Young Talent(to Deli Wang)initiatory financial support from Huazhong University of Science and Technology(HUST)~~
文摘The search for active,stable,and cost-effective electrocatalysts for hydrogen evolution reaction(HER)is desirable,but it remains a great challenge in the overall water splitting.Here,we report the synthesis of nickel boron nanoparticles supported on Vulcan carbon(Ni-B)via a simple,yet scalable,two-step chemical reduction–annealing strategy.The results of the electrochemical measurements suggest that the overpotentials of Ni-B-400 are 114 and 215 mV(in 1 mol L^–1 KOH)at current densities of 10 and 40 mA cm^?2,respectively,indicating an exceedingly good electrocatalytic activity in the HER.More importantly,Ni-B maintains a current density of 7.6 mA cm^-2 at an overpotential of 0.15 V for 20 h in the durability test.The excellent HER activity of Ni-B-400 is derived from the small particle size and the expanded lattice of Ni,which can optimize the hydrogen absorption energy and enhance the electrocatalytic properties.
文摘A series of Ce-doped Ni-B amorphous alloy catalysts were prepared by a KBH_4 reduction method, characterized by ICP, BET, XRD, H_2-chemisorption, H_2-TPD, etc., and tested in the hydrogenation of 2-ethylanthraquinone. The results of characterization show that with the addition of Ce the amount of H_2-chemisorption and H_2-TPD areas first increases markedly and then decreases with the maximum appears at the atomic ratio of Ce to Ni of 0.036. The hydrogenation activity also shows the same trend. The effects of Ce are attributed to its dispersion of Ni particles, resulting in the formation of more surface Ni centers. However, much higher Ce contents may result in the decrease of the surface Ni contents. After heat treatment at higher temperatures, the amorphous structure of Ni-B is destroyed.
基金the NNSFC, RFDP, NSFTC and NNSFCTJ for the financial support (20003006, 2000005520, 99380171 and 031606211).
文摘A supported Ni-B/TiO2 amorphous catalyst was prepared by impregnation and reduction. It was characterized by XRD, SAED, DSC, XPS, etc.. The catalytic activity of catalyst was measured through the hydrogenation of heavy arenes in petrochemicals for the first time.
基金The National Natural Science Foundation of China(No.20263003)supported this work.
文摘Uniform Ni-B amorphous alloys about 14 nm have been prepared on CNTs-A support,named Ni-B/CNTs-A. In comparison with the Ni-B/CNTs amorphous catalyst, Ni-B/CNTs-A showed higher nickel loading, determined by ICP and better catalytic activity and ethylene selectivity in the acetylene hydrogenation reaction.
文摘The influence of emissions of an active volcano on the composition of nanoparticles and ultrafine road dust was identified in an urban area of the Andes.Although many cities are close to active volcanoes,few studies have evaluated their influence in road dust composition.Air quality in urban areas is significantly affected by nonexhaust emissions(e.g.road dust,brake wear,tire wear),however,natural sources such as volcanoes also impact the chemical composition of the particles.In this study,elements from volcanic emissions such as Si>Al>Fe>Ca>K>Mg,and Si-Al with K were identified as complex hydrates.Similarly,As,Hg,Cd,Pb,As,H,Cd,Pb,V,and salammoniac were observed in nanoparticles and ultrafine material.Mineral composition was detected in the order of quartz>mullite>calcite>kaolinite>illite>goethite>magnetite>zircon>monazite,in addition to salammoniac,a tracer of volcanic sources.The foregoing analysis reflects the importance of carrying out more studies relating the influence of volcanic emissions in road dust in order to protect human health.The road dust load(RD_(10))ranged between 0.8 and 26.8 mg m^(−2)in the city.
文摘The molecular dynamics(MD)simulations were used to understand the heat transfer process between the gas phase and the solid skeleton in the nanoporous silica aerogels.The amorphous silica nanoparticles were generated by the MD simulations and the energy accommodation coefficient(EAC)between the gases and the nanoparticles was calculated based on the results of the nonequilibrium molecular dynamics(NEMD)simulations.The apparent thermal conductivity(ATC)of the gases between the heat source and heat sink was also obtained.The effects of the temperature,the particle diameter and the molecule type on the EAC and the ATC were investigated.The results indicate that the EAC decreases with the increase of temperature within the calculating range.When the preset temperature is constant,the EAC increases with the increasing of the particle diameter and eventually approaches a specific value.When the preset temperature is 300 K and the particle size is 4 nm,the obtained EAC for the N2 gas and the O2 gas is close to each other and both are less than that of the Ar gas.The results also indicate that the heat transferred through the gas-nanoparticle interface is far less than that through the neighbouring nanoparticles in silica aerogels.
基金financially supported by the National Natural Science Foundation of China (31700689)Natural Science Foundation of Shanxi Province (201901D111115)+1 种基金Scientific and Technological Innovation Programs of Higher Education Institutions in Shanxi (172040098-S)Transformation of Scientific and Technological Achievements Programs of Higher Education Institutions in Shanxi (2020CG015)
文摘Recently,multifunctional nanoparticles have shown great prospects in cancer treatment,which have the ability to simultaneously deliver the drug,image and target tumor cells.In this paper,we designed a luminescent nanoparticles platform based on hydrothermal hyaluronic acid/amorphous calcium phosphate(HA-FCNs/ACP)with multifunctional properties for drug delivery,bio-imaging,and targeting treatment.HA-FCNs/ACP shows an ability to load curcumin(Cur)with pH-sensitive responsive drug release behavior and excellent biocompatibility.HA-FCNs/ACP dispersed in the cytoplasm through the overexpressed CD44 receptor that is actively targeted into human lung cancer cells(A549 cells).Meanwhile,the viability of A549 cells was significantly inhibited in vitro.The prepared HA-FCNs and HA-FCNs/ACP both exhibit excellent targeted bioimaging performance on cancer cells.Hence,the as-prepared nanoparticles have promising applications in treating tumor disease.
基金supported by the National Natural Science Foundation of China(No.51473152 and No.51573174)Scientific Research Foundation for Young Talents from Fujian Provincial Department of Education(No.JT180494)Scientific Research Platform Construction Project from Fujian Provincial Department of Science and Technology(No.2018H2002)。
文摘Smart nanoparticles that respond to pathophysiological parameters,such as p H,GSH,and H2O2,have been developed with the huge and urgent demand for the high-efficient drug delivery systems(DDS)for cancer therapy.Herein,cubic poly(ethylene glycol)(PEG)-modified mesoporous amorphous iron oxide(AFe)nanoparticles(AFe-PEG)have been successfully prepared as p H-stimulated drug carriers,which can combine doxorubicin(DOX)with a high loading capacity of 948 mg/g,forming a novel multifunctional AFe-PEG/DOX nanoparticulate DDS.In an acidic microenvironment,the AFe-PEG/DOX nanoparticles will not only release DOX efficiently,but also release Fe ions to catalyze the transformation of H2O2 to·OH,acting as fenton reagents.In vitro experimental results proved that the AFe-PEG/DOX nanoparticles can achieve combination of chemotherapeutic(CTT)and chemodynamic therapeutic(CDT)effects on Hela tumor cells.Furthermore,the intrinsic magnetism of AFePEG/DOX makes its cellular internalization efficiency be improved under an external magnetic field.Therefore,this work develops a new and promising magnetically targeted delivery and dual CTT/CDT therapeutic nano-medicine platform based on amorphous iron oxide.
基金supported by Beijing Nova Program(Z211100002121127 and 20220484219,China)Beijing Natural Science Foundation(L212059,China)+1 种基金Fundamental Research Funds for the Central Universities(3332021101,China)CAMS Innovation Fund for Medical Sciences(CIFMS,2021-I2M-1-026 and 2021-I2M-1-028,China).
文摘Calcium-based biomaterials have been intensively studied in the field of drug delivery owing to their excellent biocompatibility and biodegradability.Calcium-based materials can also deliver contrast agents,which can enhance real-time imaging and exert a Ca^(2+)-interfering therapeutic effect.Based on these characteristics,amorphous calcium carbonate(ACC),as a brunch of calcium-based biomaterials,has the potential to become a widely used biomaterial.Highly functional ACC can be either discovered in natural organisms or obtained by chemical synthesis However,the standalone presence of ACC is unstable in vivo.Additives are required to be used as stabilizers or core-shell structures formed by permeable layers or lipids with modified molecules constructed to maintain the stability of ACC until the ACC carrier reaches its destination.ACC has high chemical instability and can produce biocompatible products when exposed to an acidic condition in vivo,such as Ca^(2+) with an immune-regulating ability and CO_(2) with an imaging-enhancing ability.Owing to these characteristics,ACC has been studied for selfsacrificing templates of carrier construction,targeted delivery of oncology drugs,immunomodulation,tumor imaging,tissue engineering,and calcium supplementation.Emphasis in this paper has been placed on the origin,structural features,and multiple applications of ACC.Meanwhile,ACC faces many challenges in clinical translation,and long-term basic research is required to overcome these challenges.We hope that this study will contribute to future innovative research on ACC.
基金financial supports from the Natural Science Foundation of China(No.50973069)the project of Postgraduate Degree Construction,Southwest University for Nationalities(No.2013XWD-S0703)
文摘Although much effort has been focused on the preparation of stable amorphous calcium phosphate （ACP） nanoparticles in aqueous solution, the redispersibility and long-term stability of ACP nanoparticles in aqueous solution remains an unresolved problem. In this work, stable colloidal ACPs were prepared by using an organic bisphosphonate （BP） as a sterically hindered agent in aqueous solution. The harvested calcium phosphate nanoparticles were characterized by inductively coupled plasma atomic emission spectrometry （ICP-AES）, Fourier transform infrared （FTIR）, X-ray diffraction （XRD）, dynamic light scattering （DLS） and transmission electron microscopy （TEM）. ICP-AES, FTIR and XRD results suggested the particles were ACP. DLS and TEM results indicated that the size of the ACP nanoparticles were in the range of 60 nm with a spherical morphology. The resulting calcium phosphate nanoparticles retained its amorphous nature in aqueous solution for at least 6 months at room temperature due to the stabilizing effect of the organic bisphosphonate. Moreover, the surface of the ACP nanoparticles adsorbed with the organic bisphosphate used showed good redispersibility and high colloid stability both in organic and aqueous solutions.
文摘The main drawbacks of vanadium oxide as a cathode material are its low conductivity, low practical capacity and poor cycling stability. Adding Cr can improve its conductivity and a metastable amorphous state may provide higher capacity and stability. In this work, metastable amorphous Cr-V-O nano- particles have been successfully prepared through a facile co-precipitation reaction followed by annealing treatment. As a cathode material for lithium batteries, the metastable amorphous Cr-V-O nanoparticles exhibit high capacity （260 mAh/g at 100 mA/g between 1.5-4 V）, low capacity loss （more than 80% was retained after 200 cycles at 100 mA/g） and high rate capability （up to 3 A/g）.
