Highly Improved Electrochemical Performances of the Nanocrystalline and Amorphous Mg_2Ni-type Alloys by Substituting Ni with M (M=Cu,Co,Mn)

The element Ni in the Mg2Ni alloy is partially substituted by M（M = Cu, Co, Mn） in order to ameliorate the electrochemical hydrogen storage performances of Mg2Ni-type electrode alloys. The nanocrystalline and amorphous Mg20Ni10-xMx（M = None, Cu, Co, Mn; x = 0-4） alloys were prepared by melt spinning. The effects of the M（M = Cu, Co, Mn） content on the structures and electrochemical hydrogen storage characteristics of the as-cast and spun alloys were comparatively studied. The analyses by XRD, SEM and HRTEM reveal that all the as-cast alloys have a major phase of Mg2Ni but the M（M = Co, Mn） substitution brings on the formation of some secondary phases, MgCo2 and Mg for the（M = Co） alloy, and Mn Ni and Mg for the（M = Mn） alloy. Besides, the as-spun（M = None, Cu） alloys display an entirely nanocrystalline structure, whereas the as-spun（M = Co, Mn） alloys hold a nanocrystalline/amorphous structure, suggesting that the substitution of M（M = Co, Mn） for Ni facilitates the glass formation in the Mg2Ni-type alloys. The electrochemical measurements indicate that the variation of M（M = Cu, Co, Mn） content engenders an obvious effect on the electrochemical performances of the as-cast and spun alloys. To be specific, the cyclic stabilities of the alloys augment monotonously with increasing M（M = Cu, Co, Mn） content, and the capacity retaining rate（S20） is in an order of（M = Cu） 〉（M = Co） 〉（M = Mn） 〉（M = None） for x≤1 but changes to（M = Co） 〉（M = Mn） 〉（M = Cu） 〉（M = None） for x≥2. The discharge capacities of the as-cast and spun alloys always grow with the rising of M（M = Co, Mn） content but first mount up and then go down with increasing M（M = Cu） content. Whatever the M content is, the discharge capacities are in sequence：（M = Co） 〉（M = Mn） 〉（M = Cu） 〉（M = None）. The high rate discharge abilities（HRDs） of all the alloys grow clearly with rising M（M = Cu, Co） content except for（M = Mn） alloy, whose HRD has a maximum value with varying M（M = Mn） content. Furthermore, for the as-cast alloys, the HRD is in order of（M = Co） 〉（M = Mn） 〉（M = Cu） 〉（M = None）, while for the as-spun（20 m·s^-1） alloys, it changes from（M = Co） 〉（M = Mn） 〉（M = Cu） 〉（M = None） for x = 1 to（M = Cu） 〉（M = Co） 〉（M = None） 〉（M = Mn） for x = 4.

Hydrogen-induced amorphization of Zr-Cu-Ni-Al alloy

Arc melting was utilized in this study to produce Zr_(55)Cu_(30)Ni_5Al_(10) alloys under mixed atmospheres with various ratios of high-purity hydrogen to argon. The influences of hydrogen addition on the solidification structure and glass-forming ability of Zr_(55)Cu_(30)Ni_5Al_(10) alloy were determined by examining microstructures in different parts of the cast ingots. The results showed that different degrees of crystallization structures were obtained in the ascast button ingots after arc melting in high-purity Ar, and the cross-sectional solidification morphology of arcmelted ingots was found to consist of crystals with varying from the bottom up. By contrast, there were completely amorphous structures in the middle and upper areas of the as-cast button ingots fabricated by adding 10% H_2 to the high-purity Ar atmosphere. A clear solidification interface was found between the crystal and glass in the ascast button ingots, which indicates that hydrogen addition can enhance the Zr_(55)Cu_(30)Ni_5Al_(10) alloy's glass-forming ability. The precise mechanism responsible for this was also investigated.

Effects of Chromium Addition on Preparation and Properties of Bulk Cementite

Bulk cementites with the Cr contents of 0,3.01,6.03,8.22,and 11.51mass% were prepared by mechanical alloying（MA）and spark plasma sintering（SPS）.The results indicated that when the Cr content was low（3.01mass%）,the phases were composed of cementite with a small amount ofα-Fe at a sintering temperature of 1 173 K,but the microstructure became single-phase alloyed cementite as the Cr content was further increased.It showed that microaddition of Cr was beneficial for promoting the formation of cementite.Furthermore,the mechanical performance of cementite can be greatly affected by the variation of Cr content.The hardness,elastic modulus and elastic recovery presented a remarkably increasing tendency with the addition of Cr,and the maximum micro-hardness and elastic modulus values reached 1 070.74 HV and 199.32 GPa,respectively,which were similar to the precipitation phase（cementite）obtained by melting and casting techniques.Moreover,when the Cr content was below 11.51mass%,the crystal structure of Fe3C-type cementite would not change with increasing the Cr content.A Cr atom replaced an Fe atom in the lattice of the cementite,and voids appeared when Cr was doped into the cementite at content of about11.51mass%,causing the relative density to decrease.