Ni-W alloys and their composite deposits are electroplated on the metals when an appropriate complex agent is selected on the base of the theories of electrochemistry and complex chemistry, and the principle of induce...Ni-W alloys and their composite deposits are electroplated on the metals when an appropriate complex agent is selected on the base of the theories of electrochemistry and complex chemistry, and the principle of induced codeposition. Effects of the bath composition, pH value, temperature and current density on the electrode position of Ni-W alloys and their composite deposits have been investigated, and the effect of heat treatment temperature on the hardness, structure and cohesive force of the amorphous Ni-W alloys and their composite deposits are also discussed. Results showed that the alloys containing more than 44 wt pct W content and the composite deposits containing 7.8 wt pct SiC content could be obtained by making use of the appropriate bath composition and plating conditions. Alloys and their composite deposits with over 44 wt pct W content show amorphous structure. The hardness of amorphous Ni-W alloys and their composite deposits increases obviously when heated, and can reach to 1350 HV and 1520 HV respectively for 46 wt pct W content. The cohesion on Cu, carbon steel and stainless steel is very good.展开更多
Cobalt-molybdenum （Co-Mo） amorphous alloy thin films were deposited on copper substrates by the electrochemical method at pH 4.0. Among the experimental electrodeposition parameters,only the concentration ratio of m...Cobalt-molybdenum （Co-Mo） amorphous alloy thin films were deposited on copper substrates by the electrochemical method at pH 4.0. Among the experimental electrodeposition parameters,only the concentration ratio of molybdate to cobalt ions （[MoO4^2-]/[Co^2＋]） was varied to analyze its influence on the mechanism of induced cobalt-molybdenum codeposition. Voltammetry was one of the main techniques,which was used to examine the voltammetric response,revealing that cobalt-molybdenum codeposition depended on the nature of the species in solution. To correlate the type of the film to the electrochemical response,various cobalt-molybdenum alloy thin films obtained from different [MoO4^2-]/[Co^2＋] solutions were tested. Crack-free homogeneous films could be easily obtained from the low molybdate concentrations （[MoO4^2-]/[Co^2＋]≈0.05） applying low deposition potentials. Moreover,the content of molybdenum up to 30wt% could be obtained from high molybdate concentration; in this case,the films showed cracks. The formation of these cracked films could be predicted from the observed distortions in the curves of electric current-time （j-t） deposition transients. The films with amorphous structure were obtained. The hysteresis loops suggested that the easily magnetized axis was parallel to the surface of the films. A saturation magnetization of 137 emu·g^-1 and a coercivity of 87 Oe of the film were obtained when the deposition potential was -1025mV,and [ MoO4^2-]/[Co^2＋] was 0.05 in solution,which exhibited a nicer soft-magnetic response.展开更多
The formation mechanism of the amorphous Ni-Fe-P coating was studied by analysis of the forming thermodynamics, dynamics, and crystallography of the amorphous alloy. The results show that, in the initial stage of depo...The formation mechanism of the amorphous Ni-Fe-P coating was studied by analysis of the forming thermodynamics, dynamics, and crystallography of the amorphous alloy. The results show that, in the initial stage of deposition a thin 'crystal epitaxial growth' layer first forms, and then transforms to amorphous gradually. The cross section in Ni-Fe-P coatings by electrolytic etching exhibits a banded structure of alternate dark and light bands. It is proposed that the banded structure is caused by a change in the P content with thickness,which is due to alternated depletion and enrichment of [OH-] in the diffusion layer resulting from the generation and evolution of hydrogen gas. The amorphous Ni-Fe-P coating will be formed in proper composition, high nucleation rate and strongly hindered growth of the crystal nucleus. Amorphous Ni-Fe-P alloys form as islands, and grow up by layer.展开更多
To strengthen the properties of Ni-W alloy, dimethylamine borane （DMAB） was added to an alloy Ni-W electrolyte solution and a ternary Ni-W-B alloy was electrodeposited. The electrodeposition, crystallographic struct...To strengthen the properties of Ni-W alloy, dimethylamine borane （DMAB） was added to an alloy Ni-W electrolyte solution and a ternary Ni-W-B alloy was electrodeposited. The electrodeposition, crystallographic structure, surface morphology, heat treatment and corrosion resistance, of the alloy were studied by DSC, XRD, SEM and electrochemical techniques. The results showed that the structure of the alloy was greatly affected by the cooperation of boron compound. DSC experiment combined with X-ray diffractometry indicated that the obtained Ni-W-B alloy was still in amorphous structure although W content in the alloy was decreased by the addition of DMAB. After heat treatment at 400 ℃ for 1 h, the microhardness was increased from 612 to 947 kg.mm^-2 that was com- parative to Cr coating. The appearance of the as-plated coating was in f＇me and slice grains and kept almost no change after heat treatment. In w=0.03 NaC1 solution the as-plated coating presented very good corrosion resistance. After the coating was heat-treated its corrosion resistance was enhanced.展开更多
A new technique of electroplating amorphous Fe-Ni-W alloy deposits was proposed.The structure and morphology o Fe-Ni-W alloy deposit were detected by XRD and SEM.The friction and wear behavior of Fe-Ni-W alloy deposit...A new technique of electroplating amorphous Fe-Ni-W alloy deposits was proposed.The structure and morphology o Fe-Ni-W alloy deposit were detected by XRD and SEM.The friction and wear behavior of Fe-Ni-W alloy deposit were studied and compared with that of chromium deposit.The corrosion properties against 5% sodium chloride,5% sulfuric acid and 5% sodium hydroxide were also discussed.The experimental results indicate that Fe-Ni-W alloy deposits have superior properties against wea than hard chromium deposits under dry sliding condition.Under oil sliding condition,except their better wear resistance,the deposits can protect their counterparts against wear.The deposits plated on brass and AISI 1045 steel show good behavior against corrosion o 5% sodium chloride,5% sulfuric acid and 5% sodium hydroxide.The bath of electroplating amorphous Fe-Ni-W alloy deposits is environmentally friendly and would find widely use in industry.展开更多
The microstructures, friction and wear behavior under dry sliding condition of electrodeposited amorphous Fe-Co-W alloy deposits heat treated at different temperatures were studied. A comparative study of hard chrome ...The microstructures, friction and wear behavior under dry sliding condition of electrodeposited amorphous Fe-Co-W alloy deposits heat treated at different temperatures were studied. A comparative study of hard chrome deposit under the same testing condition was also made. The experimental results show that the hardness and wear resistance of amorphous Fe-Co-W alloy deposits are improved with the increasing of heat treatment temperature, and reach the maximum value at 800 ℃, then decrease above 800 ℃. Under 40 N load, the wear resistance properties of the alloy deposits heat treated at 800 ℃ are superior to those of hard chrome deposit. The main wear mechanisms of amorphous Fe-Co-W alloy deposits heat treated below 600 ℃ are peeling, plastic and flowing deformation; when the deposits are heat treated above 700 ℃, they are plastic and flowing deformation. While the main wear mechanisms of hard chrome are abrasive wear, fatigue and peeling.展开更多
文摘Ni-W alloys and their composite deposits are electroplated on the metals when an appropriate complex agent is selected on the base of the theories of electrochemistry and complex chemistry, and the principle of induced codeposition. Effects of the bath composition, pH value, temperature and current density on the electrode position of Ni-W alloys and their composite deposits have been investigated, and the effect of heat treatment temperature on the hardness, structure and cohesive force of the amorphous Ni-W alloys and their composite deposits are also discussed. Results showed that the alloys containing more than 44 wt pct W content and the composite deposits containing 7.8 wt pct SiC content could be obtained by making use of the appropriate bath composition and plating conditions. Alloys and their composite deposits with over 44 wt pct W content show amorphous structure. The hardness of amorphous Ni-W alloys and their composite deposits increases obviously when heated, and can reach to 1350 HV and 1520 HV respectively for 46 wt pct W content. The cohesion on Cu, carbon steel and stainless steel is very good.
文摘Cobalt-molybdenum （Co-Mo） amorphous alloy thin films were deposited on copper substrates by the electrochemical method at pH 4.0. Among the experimental electrodeposition parameters,only the concentration ratio of molybdate to cobalt ions （[MoO4^2-]/[Co^2＋]） was varied to analyze its influence on the mechanism of induced cobalt-molybdenum codeposition. Voltammetry was one of the main techniques,which was used to examine the voltammetric response,revealing that cobalt-molybdenum codeposition depended on the nature of the species in solution. To correlate the type of the film to the electrochemical response,various cobalt-molybdenum alloy thin films obtained from different [MoO4^2-]/[Co^2＋] solutions were tested. Crack-free homogeneous films could be easily obtained from the low molybdate concentrations （[MoO4^2-]/[Co^2＋]≈0.05） applying low deposition potentials. Moreover,the content of molybdenum up to 30wt% could be obtained from high molybdate concentration; in this case,the films showed cracks. The formation of these cracked films could be predicted from the observed distortions in the curves of electric current-time （j-t） deposition transients. The films with amorphous structure were obtained. The hysteresis loops suggested that the easily magnetized axis was parallel to the surface of the films. A saturation magnetization of 137 emu·g^-1 and a coercivity of 87 Oe of the film were obtained when the deposition potential was -1025mV,and [ MoO4^2-]/[Co^2＋] was 0.05 in solution,which exhibited a nicer soft-magnetic response.
文摘The formation mechanism of the amorphous Ni-Fe-P coating was studied by analysis of the forming thermodynamics, dynamics, and crystallography of the amorphous alloy. The results show that, in the initial stage of deposition a thin 'crystal epitaxial growth' layer first forms, and then transforms to amorphous gradually. The cross section in Ni-Fe-P coatings by electrolytic etching exhibits a banded structure of alternate dark and light bands. It is proposed that the banded structure is caused by a change in the P content with thickness,which is due to alternated depletion and enrichment of [OH-] in the diffusion layer resulting from the generation and evolution of hydrogen gas. The amorphous Ni-Fe-P coating will be formed in proper composition, high nucleation rate and strongly hindered growth of the crystal nucleus. Amorphous Ni-Fe-P alloys form as islands, and grow up by layer.
基金Project supported by the Natural Science Foundation of Fujian Province （No. E0210005） and the National Natural Science Foundation of China （No. 29773039）.
文摘To strengthen the properties of Ni-W alloy, dimethylamine borane （DMAB） was added to an alloy Ni-W electrolyte solution and a ternary Ni-W-B alloy was electrodeposited. The electrodeposition, crystallographic structure, surface morphology, heat treatment and corrosion resistance, of the alloy were studied by DSC, XRD, SEM and electrochemical techniques. The results showed that the structure of the alloy was greatly affected by the cooperation of boron compound. DSC experiment combined with X-ray diffractometry indicated that the obtained Ni-W-B alloy was still in amorphous structure although W content in the alloy was decreased by the addition of DMAB. After heat treatment at 400 ℃ for 1 h, the microhardness was increased from 612 to 947 kg.mm^-2 that was com- parative to Cr coating. The appearance of the as-plated coating was in f＇me and slice grains and kept almost no change after heat treatment. In w=0.03 NaC1 solution the as-plated coating presented very good corrosion resistance. After the coating was heat-treated its corrosion resistance was enhanced.
基金Project(04GK1007) supported by the Science and Technology Office of Hunan Province,China
文摘A new technique of electroplating amorphous Fe-Ni-W alloy deposits was proposed.The structure and morphology o Fe-Ni-W alloy deposit were detected by XRD and SEM.The friction and wear behavior of Fe-Ni-W alloy deposit were studied and compared with that of chromium deposit.The corrosion properties against 5% sodium chloride,5% sulfuric acid and 5% sodium hydroxide were also discussed.The experimental results indicate that Fe-Ni-W alloy deposits have superior properties against wea than hard chromium deposits under dry sliding condition.Under oil sliding condition,except their better wear resistance,the deposits can protect their counterparts against wear.The deposits plated on brass and AISI 1045 steel show good behavior against corrosion o 5% sodium chloride,5% sulfuric acid and 5% sodium hydroxide.The bath of electroplating amorphous Fe-Ni-W alloy deposits is environmentally friendly and would find widely use in industry.
文摘The microstructures, friction and wear behavior under dry sliding condition of electrodeposited amorphous Fe-Co-W alloy deposits heat treated at different temperatures were studied. A comparative study of hard chrome deposit under the same testing condition was also made. The experimental results show that the hardness and wear resistance of amorphous Fe-Co-W alloy deposits are improved with the increasing of heat treatment temperature, and reach the maximum value at 800 ℃, then decrease above 800 ℃. Under 40 N load, the wear resistance properties of the alloy deposits heat treated at 800 ℃ are superior to those of hard chrome deposit. The main wear mechanisms of amorphous Fe-Co-W alloy deposits heat treated below 600 ℃ are peeling, plastic and flowing deformation; when the deposits are heat treated above 700 ℃, they are plastic and flowing deformation. While the main wear mechanisms of hard chrome are abrasive wear, fatigue and peeling.
