纤维加筋层厚度对边坡抗蚀性影响试验研究

纤维加筋土对边坡有良好的防护效果,为确定纤维加筋层最佳厚度,分别按纤维长度为5、10、20、30 mm和加筋率(纤维质量占干土质量的比例)为0.1%、0.2%、0.3%、0.4%、0.5%,制作麦秸秆纤维加筋土试样,通过崩解试验确定纤维长20 mm、加筋率0.3%为麦秸秆纤维加筋土最佳配比,进而按此配比设置麦秸秆纤维加筋层厚度分别为0、3、6、9 cm的45°边坡,进行强度为12 mm/h、持续时间为9 h的模拟降雨冲刷试验。试验结果表明:在强降雨情况下,麦秸秆纤维加筋层提高边坡抗蚀性的效果明显,纤维加筋层厚度越大边坡土体体积含水率越高、冲蚀量越小,纤维加筋层厚度为3、6、9 cm边坡的冲蚀量分别较无纤维加筋层边坡的冲蚀量减少53.4%、66.0%、67.0%,但厚度达到6 cm后随厚度继续增大边坡土体含水率不再明显增大、冲蚀量不再明显减小。从纤维加筋层对边坡土体含水率和抗蚀性的影响、整体防护效果及成本等方面综合分析,认为麦秸秆纤维加筋层最优厚度为6 cm。

侵犯商业秘密罪评价标准的修正与规范解读

《刑法修正案(十一)》完成了侵犯商业秘密罪由数额犯到情节犯的全面转型,但未跟进更新的司法解释易使得司法实务将情节犯作数额犯化处理,仅关注数额要素对于犯罪评价的影响。侵犯商业秘密罪所保护的是复合法益:一是商业秘密权利人对商业秘密享有的私权利,二是市场竞争秩序,后者又可还原为具体的个人法益——商业秘密权。以此为逻辑起点,侵犯商业秘密罪的评价体系应当坚持区分性、形式与实质相统一、强保护的原则,建构综合评价体系。各要素不可单独作为入罪标准,而应综合考量,建构起以数额要素为主,非数额要素为辅的“情节严重”解释体系。

Study on the Relationship between the Main Secondary Metabolites and Polysaccharide in Fruits of Lycium barbarum at Different Application Amounts of Nitrogen

[Objective] The aim of this study is to investigate the optimum application amount of nitrogen in Lycium barbarum based on considering the relationship between main secondary metabolites and polysaccharide.[Method]Under field conditions,the effects of different application amounts of nitrogen on main secondary metabolites of betaine,carotenoid and flavone of Lycium barbarum and the relationship between main secondary metabolites and polysaccharide.[Result] The main secondary metabolites of betaine,carotenoid and flavone of Lycium barbarum varied under different application amounts of nitrogen.The proper application amount of nitrogen(600-900 kg/hm2)was beneficial to the formation and accumulation of secondary metabolites such as carotenoids.Correlation analysis results showed that polysaccharide were negatively correlated with betaine,carotenoid and flavone at significant probability level.[Conclusion]Considering the relationship between the output and quality of the fruits of Lycium barbarum,the optimum nitrogen application amount should be 600-900 kg/hm2.

不同固化剂加固滨海软土的强度特性室内试验研究

为提高固化剂加固滨海软土的强度特性与时效性,通过室内试验研究固化剂类型、固化剂掺量、水灰比、搅拌均匀性、养护条件等因素作用下固化滨海软土强度的演化规律。试验结果表明:不同固化剂加固软土的抗压强度随着养护期龄的延长持续增加,将水泥替换为HR软土固化剂可有效提高软土加固体的抗压强度。拌合时间越长,软土加固体的抗压强度越高;相同的拌合时间,水泥软土加固体的抗压强度远低于HR固化剂加固软土的抗压强度;利用HR软土固化剂加固软土能够在保障施工质量的基础上,有效缩短施工工期。随着水灰比的增加,软土加固体的抗压强度明显降低;相同的水灰比,HR固化剂加固软土的抗压强度均大于水泥软土加固体的抗压强度。软土加固体在养护过程中,温度与湿度在固化剂水化过程中发挥重要作用,影响软土加固体的抗压强度;相同的固化剂掺量,标准养护条件下软土加固体的抗压强度比低温养护提高2倍以上;软土加固体早期抗压强度随着养护期龄的延长增加显著,当期龄达到14 d后,随着期龄的增加软土加固体的抗压强度增长趋势明显变缓。

Analysis on the Contribution of Artificial Precipitation Enhancement Amount to Annual Water Resources in Liaoning

Based on the water resource balance,the correlation between both the Liaoning water resource and precipitation and total amount of water resource from 1991 to 2004 was analyzed by assuming Liaoning to be an enclosed region.And the calculation methods were developed to quantitatively determine the increase of rainfall due to artificial precipitation,and consequently ascertain the contribution of artificial rainfall amount to water resources.

模糊PID玉米免耕机排种施肥控制方法研究

为了实现免耕机播种量和施肥量的精确控制,基于模糊PID控制,设计了控制系统。首先,建立排种量模型,以排种轴转速为控制量;其次,建立施肥量控制模型,分析排肥轴转速、排肥轴长度和免耕机前进速度对于排肥量误差的影响,选择排肥轴转速为控制量;再次,采用模糊PID控制的方法,对驱动电机进行调速,进而实现对排肥轴和排种轴转速的控制,完成排种量和排肥量的调整;最后,对系统进行测试。测试结果表明:电机转速从0调整到50 r/min的响应时间为0.8 s,施肥量变异系数分布区间为[2.6,4.1]。

Monthly variation in litterfall and the amount of nutrients in an Aleurites montana plantation

In this study, the dynamics of monthly variation in litterfall and the amount of nutrients, i.e., organic C, N, P and K, in an Aleurites montana plantation were analyzed, based on a field study and experiments over one year. The results show that the litterfall mass of A. montana collected generally presents an ascending trend with maximum defoliation occurring in the autumn and winter （October-December）, accounting for 75.67% of the total amount of annual litterfalk The sequence in the amount of nutrients in A. montana litter was as follows： organic C 〉 N 〉 K 〉 P; their monthly amounts show various dynamic curves. Similar to the dynamics of the mass of monthly litterfall, the monthly returns of C, N, P and K generally show an ascending trend with their peak values all occurring in December. The mass of A. montana litterfall and the dynamics of its monthly nutrient return provide, to a certain degree, a scientific reference for planting and fertilizing A. montana.

Effects of Chemical Components on the Amount of Green Tea Cream

The relationship between the amount of tea cream and the chemical components contents in the original green tea infusion was investigated. The results showed that the amounts of tea cream in the green tea infusions obtained from different cultivars and different parts of new shoots were varied. There were many chemical components participating in the formation of green tea cream. However, there were only the contents of caffeine （Y=0.85, P〈0.01） and polyphenols （Y=0.65, P〈0.05） in the original green tea infusion highly correlated with the amount of green tea cream. Stepwise regression analysis of overall chemical components indicated that the contents of caffeine and gallated catechins in the original green tea infusion had a significant effect （P〈0.01） on green tea cream levels. Cream （g L-1）=-172.071＋ 0.129×Ccaffeine＋0.024×Ggallated catechins （R2=0.936）. The amount of green tea cream can be predicted by the contents of gallated catechins and caffeine in the original tea infusion. Principal component analysis also indicated that catechins, minerals, and polysaccharides were the important chemical components in the formation of green tea cream.

Study on the Optimum Moisture Amount Added to Brown Rice once during the Wet Conditioning

In the experiment, the brown rice whose moisture content was 12.5% was used as raw material. The brown rice was grouped, then moisturized differently and milled. While milling, the energy consumption, the rate of broken rice and the crack rate were tested. It is confirmed that the stress crack owing to the moisture added to the brown rice can be avoided when the moisture amount added once is limited to no more than 1.5%. It is also proved that the energy consumption can be reduced, the yielding rate of rice can be increased and that the quality of rice can be improved.

Research on the effect of the heavy nuclei amount on the temperature reactivity coefficient in a small modular molten salt reactor

Small modular thorium-based graphite-moderated molten salt reactors (smTMSRs), which combine the advantages of small modular reactors and molten salt reactors, are regarded as a wise development path to speed deployment time. In a smTMSR, low enriched uranium and thorium fuels are used in once-through mode, which makes a marked difference in their neutronic properties compared with the case when a conventional molten salt breeder reactor is used. This study investigated the temperature reactivity coefficient (TRC) in a smTMSR, which is mainly affected by the molten salt volume fraction (VF) and the heavy nuclei concentration in the fuel salt (HN). The fourfactor formula method and the reaction rate method were used to indicate the reasons for the TRC change, including the fuel density effect, the fuel Doppler effect, and the graphite thermal scattering effect. The results indicate that only the fuel density has a positive effect on the TRC in the undermoderated region. Thermal scattering from both salt and graphite has a significant negative influence on the TRC in the overmoderated region. The maximal effective multiplication factor, which shows the highest fuel utilization, is located at 10% VF and 12 mol% HN and is still located in the negative TRC region. In addition, on increasing the heavy nuclei amount from 2 mol% HN to 12 mol% HN (VF = 10%), the total TRC undergoes an obvious change from - 11 to - 3 pcm/K, which implies that the change in the HN caused by the fuel feed online should be small to avoid potential trouble in the reactivity control scheme.

Proper In deposition amount for on-demand epitaxy of InAs/GaAs single quantum dots

The test-QD in-situ annealing method could surmount the critical nucleation condition of InAs/GaAs single quantum dots（SQDs） to raise the growth repeatability.Here,through many growth tests on rotating substrates,we develop a proper In deposition amount（θ） for SQD growth,according to the measured critical θ for test QD nucleation（θ;）.The proper ratio θ/θ;,with a large tolerance of the variation of the real substrate temperature(T;),is 0.964-0.971 at the edge and> 0.989 but < 0.996 in the center of a 1/4-piece semi-insulating wafer,and around 0.9709 but < 0.9714 in the center of a 1/4-piece N;wafer as shown in the evolution of QD size and density as θ/θ;varies.Bright SQDs with spectral lines at 905 nm-935 nm nucleate at the edge and correlate with individual 7 nm-8 nm-height QDs in atomic force microscopy,among dense 1 nm-5 nm-height small QDs with a strong spectral profile around 860 nm-880 nm.The higher T;in the center forms diluter,taller and uniform QDs,and very dilute SQDs for a proper θ/θ;:only one 7-nm-height SQD in25 μm;.On a 2-inch（1 inch = 2.54 cm） semi-insulating wafer,by using θ/θ;= 0.961,SQDs nucleate in a circle in 22%of the whole area.More SQDs will form in the broad high-T;region in the center by using a proper θ/θ;.

Amount and temperature effects responsible for precipitation isotope variation in the southern slope of Himalayas

Seasonal variation of stable isotopes in precipitation of Kathmandu Valley on the southem slope of Himalaya was carried out to understand the controlling mechanism of amount and temperature effect on the basis of one year stable isotope data from 2010 to 2011. Highly depleted isotope values in major rainy period are obtained just after the onset of precipitation in summer, which ac- counts for ＂amount effect＂ due to saturation isotopic compositions in high moisture condition, whereas, the higher values in winter are indicative to regional vapors （temperature effect） recycling of various sources. An abrupt depletion of isotope values in mid- June, indicates the onset date of monsoon precipitation, by the replacement of winter air mass with southem monsoon. Thus, pre- cipitation isotopes are a tool revealing the onset date of summer monsoon and temporal features of variability, in local and regional monsoons precipitations. A comparison of long term monthly values of 5180, temperature, and precipitation with GNIP 6180 data shows the temporal variations of stable isotopes are mostly controlled by amount and temperature effects. During summer mon- soon, the amount effects are stronger for high values of precipitation （R=0.7） and altitude effect appears for low moisture in late rainy season, thus from December to June （winter to pre-monsoon） the controlling features of isotopes remains under the temper- ature effect. A temporal rate of temperature effect is derived as 0.04%0 per year which indicates a dry signal of atmospheric condition and a temperature relation 5180=（0.371±0.08）T＋（0.156±0.05） is obtained from this analysis. The meteoric water lines of Kathmandu before and after monsoon onset of 2011, are found as 5D=（4.36±0.3）5180＋（15.66±1.2） and 5D=（6.91±0.2）S180-（7.92±2.26） from lab samples result, and 5D=9.25180＋11.725 and 5D=8.535180＋16.65 from GNIP data, which lacks the consistency both for slopes and intercepts values for the study period. The mean lapse rate values of δ18O and δD from GNIP data are obtained as -0.002‰/m and -0.015 ‰/m, which indicate the altitudinal effects in regional precipitation of the southern slope of Himalayas. This study estimates new stable isotopes data in recent precipitation using simple methodology which can be important for regional precipitation monitoring systems, environmental change and paleo-climatic studies.

Information About Low Cloud Amount Recorded in δ^(13)C Series of Tree Ring Cellulose of Pinus Koraiensis in Antu Area, Jilin

Relationship between the δ 13C of tree ring cellulose from Pinus Koraiensis and climate parameters was investigated. A significantly negative correlation between δ 13C and mean low-cloud amount from May to July was discovered, which contributes to reconstructing the mean low-cloud amount from May to July at Antu in recent 200 years. Periodicals of quasi-8-year, quasi-4-year and quasi-2-year were detected both in δ 13C series and in the reconstructed low cloud amount series with 95% confidence level. Quasi-8-year period may reflect the integrated influence of solar activity, monsoon activity and local regional factors. Quasi-4-year and quasi-2-year periods indicate the influences of ENSO and Quasi Biennial Oscillation (QBO) of East Asian monsoon, respectively.

Study on the Total Amount Control of Atmospheric Pollutant Based on GIS

To provide effective environmental management for total amount control of atmospheric pollutants. Methods An atmospheric diffusion model of sulfur dioxide on the surface of the earth was established and tested in Shantou of Guangdong Province on the basis of an overall assessment of regional natural environment, social economic state of development, pollution sources and atmospheric environmental quality. Compared with actual monitoring results in a studied region, simulation values fell within the range of two times of error and were evenly distributed in the two sides of the monitored values. Predicted with the largest emission model method, the largest emission of sulfur dioxide would be 54 279.792 tons per year in 2010. Conclusion The mathematical model established and revised on the basis of GIS is more rational and suitable for the regional characteristics of total amount control of air pollutants.

Gastrointestinal Tract Development in Unweaned Calves Feeding Different Amounts of Milk and Different Starters

This study was conducted to determine the effect of different starter diets and different amounts of milk on growth performance and gastrointestinal tract development in unweaned calves. 16 calves were assigned to 4 groups, 4 calves in each group. These four groups received the following treatments respectively: 1) high milk (6 L) + low starch (21%), high NDF (28%), high molasses (10%) starter (HMLS group);2) high milk (6L) + high starch (40%), low NDF (14%), low molasses (5%) starter (HMHS group);3) low milk (3 L) + low starch (21%), high NDF (28%), high molasses (10%) starter (LMLS group);4) low milk (3 L) + high starch (40%), low NDF (14%), low molasses (5%) starter (LMHS group). The trial was of 2 × 2 factorial design. All calves had free access to hay and water. Results showed that the low milk allowance increased calf concentrate dry matter intake (DMI) and total DMI, reduced body height at 4 weeks of age, reduced heart girth at 6 weeks of age (P < 0.05). The low milk allowance increased complex stomach full weight, reticulorumen full weight, and the percentages of stomach full weight and reticulorumen full weight over body weight (P < 0.05). The low starch, high fiber, high molasses starters reduced the complex stomach full weight, the proportion of the complex stomach empty weight over body weight, reticulorumen empty weight, abomasum full weight, the proportion of abomasum empty weight over body weight and reticulorumen volume (P < 0.05). The low milk allowance increased calf intestine length, small intestine full weight, the proportion of small intestine full weight over body weight, but reduced the jejunum villus width (P < 0.05), increased ruminal pH (P < 0.05). The low milk allowance reduced papilla length in rumen anterior ventral blind sac, but increased papilla length in the posterior ventral sac

Minimum Amount of Extracting Solvent of a Separation of Two Rare Earth Components

A significant development in the theory of countercurrent extraction will be presented in this article. New expressions of the term in countercurrent extraction process analysis, “Adjacent Stage Impurity Ratio” (ASIR), are deduced. Furthermore, based on the term together with mass balance and extraction equilibrium, the conditions where a given countercurrent extraction separation operation can have minimum amounts of both extracting solvent and scrubbing agent solution can be estimated, and the equations of the two minimum amounts can be deduced. It was found that the equations for a two-component separation using a single aqueous or organic feed are exactly the same as they appeared in the theory initially established in 1970s. Unlike its earlier version, the present derivation does not involve feed-stage-composition hypothesis, and also has the advantage of dealing with a double-feed system where both aqueous and organic feeds are simultaneously employed whereas the earlier theory can only analyze a separation using a single aqueous or organic feed.

The effect of particle size and amount of inoculum on fungal treatment of wheat straw and wood chips

Background： The aim of this study was to optimize the fungal treatment of lignocellulosic biomass by stimulating the colonization. Wheat straw and wood chips were treated with Ceriporiopsis subvermispora and Lentinula edodes with various amounts of colonized millet grains（0.5, 1.5 or 3.0 % per g of wet weight of substrate） added to the substrates. Also, wheat straw and wood chips were chopped to either 0.5 or 2 cm.Effectiveness of the fungal treatment after 0, 2, 4, 6, or 8 wk of incubation was determined by changes in chemical composition, in vitro gas production（IVGP） as a measure for rumen degradability, and ergosterol content as a measure of fungal biomass.Results： Incomplete colonization was observed for C. subvermispora treated wheat straw and L. edodes treated wood chips. The different particle sizes and amounts of inoculum tested, had no significant effects on the chemical composition and the IVGP of C. subvermispora treated wood chips. Particle size did influence L.edodes treatment of wheat straw. The L. edodes treatment of 2 cm wheat straw resulted in a more selective delignification and a higher IVGP than the smaller particles. Addition of 1.5 % or 3 % L. edodes inoculum to wheat straw resulted in more selective delignification and a higher IVGP than addition of 0.5 % inoculum.Conclusion： Particle size and amount of inoculum did not have an effect on C. subvermispora treatment of wood chips. At least 1.5 % L. edodes colonized millet grains should be added to 2 cm wheat straw to result in an increased IVGP and acid detergent lignin（ADL） degradation.

Effect of Straw Mixing Amount on Mechanical Properties of Admixture-adding Hollow Block

The bonding mechanism between straw and concrete was analyzed through testing the compressive strength and flexural strength of hollow block, with different straw amount and different dosage and types of admixtures. The test results show that the mechanical properties of hollow blocks reduced after adding straws, and the more straws was added, the more hollow block density decreased. But adding A12（SO4）3 and CaC12 could improve the dense degree between rice straw and concrete. And when the proportion of straw mixing amount was 10%, the flexural strength of the early strength agent （2% A12（SO4）3, CaC12） added hollow block reached as maximal as 3.1 MPa, while the compressive strength was 9.1 MPa, consisting with the strength grade of common concrete hollow block MU7.5.

Calculating Model of Interference Amount for Miniaturized Gear and Shaft Shrink Fit

Based on miniaturized components＇ characteristics, the method of assembling miniaturized gear and shaft together with corresponding calculating model of the interference amount are proposed. On the basis of main effecting factors analysis on the gear and shaft assembling interference amount, calculating formula including all factors effective on the interference amount necessary for reliable system running was built up. The methods of reverse calculating theoretical model was used to build up the equivalent simulation model of the theoretical one, together with simulation verification and case study for calculating formula. The results show that the cold assembling method is applicable for miniaturized gear and shaft, but in the assembling process, the interference amount compensating the shape error of contacting surfaces takes a large proportion, which is the main cause of stress variance on contacting surfaces.