Broadband Dual-Input Doherty Power Amplifier Design Based on a Simple Adaptive Power Dividing Ratio Function

In this paper,a simple adaptive power dividing function for the design of a dual-input Doherty power amplifier(DPA)is presented.In the presented approaches,the signal separation function(SSF)at different frequency points can be characterized by a polynomial.And in the practical test,the coefficients of SSF can be determined by measuring a small number of data points of input power.Same as other dualinput DPAs,the proposed approach can also achieve high output power and back-off efficiency in a broadband operation band by adjusting the power distribution ratio flexibly.Finally,a 1.5-2.5 GHz highefficiency dual-input Doherty power amplifier is implemented according to this approach.The test results show that the peak power is 48.6-49.7d Bm,and the 6-d B back-off efficiency is 51.0-67.0%,and the saturation efficiency is 52.4-74.6%.The digital predistortion correction is carried out at the frequency points of 1.8/2.1GHz,and the adjacent channel power ratio is lower than-54.5d Bc.Simulation and experiment results can verify the effectiveness and correctness of the proposed method.

Three-channel CMOS transimpedance amplifier for LiDAR sensor receiver

For time-of-flight(TOF)light detection and ranging(LiDAR),a three-channel high-performance transimpedance amplifier(TIA)with high immunity to input load capacitance is presented.A regulated cascade(RGC)as the input stage is at the core of the complementary metal oxide semiconductor(CMOS)circuit chip,giving it more immunity to input photodiode detectors.A simple smart output interface acting as a feedback structure,which is rarely found in other designs,reduces the chip size and power consumption simultaneously.The circuit is designed using a 0.5μm CMOS process technology to achieve low cost.The device delivers a 33.87 dB?transimpedance gain at 350 MHz.With a higher input load capacitance,it shows a-3 dB bandwidth of 461 MHz,indicating a better detector tolerance at the front end of the system.Under a 3.3 V supply voltage,the device consumes 5.2 mW,and the total chip area with three channels is 402.8×597.0μm2(including the test pads).

Channel estimation in integrated radar and communication systems with power amplifier distortion

To reduce the negative impact of the power amplifier(PA)nonlinear distortion caused by the orthogonal frequency division multiplexing(OFDM)waveform with high peak-to-average power ratio(PAPR)in integrated radar and communication(RadCom)systems is studied,the channel estimation in passive sensing scenarios.Adaptive channel estimation methods are proposed based on different pilot patterns,considering nonlinear distortion and channel sparsity.The proposed methods achieve sparse channel results by manipulating the least squares(LS)frequency-domain channel estimation results to preserve the most significant taps.The decision-aided method is used to optimize the sparse channel results to reduce the effect of nonlinear distortion.Numerical results show that the channel estimation performance of the proposed methods is better than that of the conventional methods under different pilot patterns.In addition,the bit error rate performance in communication and passive radar detection performance show that the proposed methods have good comprehensive performance.

OPTIMIZATION DESIGN METHOD FOR INPUT IMPEDANCE MATCHING NETWORK OF LOW NOISE AMPLIFIER

According to the theories of optimal noise match and optimal power match, a method for calculating the optimal source impedance of low noise amplifier （LNA） is proposed based on the input reflection coefficient S11. Moreover.with the help of Smith chart, the calculation process is detailed, and the trade-off between the lowest noise figure and the maximum power gain is obtained during the design of LNA input impedance matching network. Based on the Chart 0. 35-μm CMOS process, a traditional cascode LNA circuit is designed and manufactured. Simulation and experimental results have a good agreement with the theoretical analysis, thus proving the correctness of theoretical analysis and the feasibility of the method.

东海OBN和三维DAS-VSP数据的联合采集与处理方法研究

近年来,光纤传感技术已经应用于地面地震数据、海洋地震数据、井中地震数据和井地联合地震数据的采集,推动了光纤传感技术在地球物理特别是地震数据采集中的应用。井地或井海联合地震勘探是陆地或海洋三维地震与三维DAS-VSP勘探相结合形成的三维立体地震勘探方法,利用井海联采的三维DAS-VSP数据,可以获得地下井周围准确的时深关系、地层速度、反褶积算子、球面扩散补偿因子、吸收衰减因子、各向异性参数和井筒周围的高分辨率构造成像,这些参数可以基于井驱处理提高陆地或海洋三维地震数据的处理质量。在中国东海某OBN数据勘探中首次开展了井下套管内铠装光缆同步采集的三维DAS-VSP数据的处理方法研究以及成像处理。首先,采用常规的三维VSP数据成像处理技术对三维DAS-VSP数据进行常规处理,具体处理流程包括:观测系统定义、预处理、初至拾取、静校正、振幅补偿、反褶积、波场分离、速度分析与建模和利用上行反射波进行井周围地层的构造成像;然后,再根据海上三维DAS-VSP数据下行多次波的特点,研发了海上三维DAS-VSP数据的下行多次波成像技术,扩展了三维DAS-VSP数据成像范围,提高了三维DAS-VSP数据成像的整体质量。与本工区早期的三维OBC数据成像结果相比,本次三维DAS-VSP数据的下行多次波成像结果表明,井周围三维构造成像质量得到了显著改进,大幅度扩展了成像范围;新采集的OBN数据和三维DAS-VSP数据的成像结果展示了更为详细和较高分辨率的构造成像,基于新的成像资料,对储层顶部和储层内流体的识别与追踪变得更加容易和清晰。井海联采技术生产效率高且成本低,既能快速获得三维DAS-VSP数据及成像,还能对三维海洋地震数据进行井驱提高分辨率处理。此外,三维OBN或OBC数据和三维DAS-VSP数据还能够进行融合处理,实现井地或井海同步采集数据的联合偏移成像,可以大幅度提高三维海洋地震数据的成像品质,值得在有条件的地方推广应用。

基于“脑肠轴理论”探讨龟羚帕安丸对PD大鼠纹状体DA及血清CCK、VIP水平影响的研究

目的:基于“脑肠轴理论”探讨龟羚帕安丸对PD大鼠纹状体裂解液多巴胺(Dopamine,DA)、血清胆囊收缩素(cholecystokinin,CCK)及血管活性肠肽(vasoactive intestinal peptide,VIP)水平的影响。方法:采用6-羟基多巴胺注射法制作PD大鼠模型,随机分为模型组、西药组、中药高、中、低剂量组,每组15只,另设15只假手术组。模型组及假手术组给予等容积生理盐水灌胃,其余组给予相应药物灌胃,连续给药4周。酶联免疫吸附测定法(ELISA)检测纹状体裂解液DA及血清CCK、VIP水平。结果:模型组大鼠纹状体DA、血清CCK及VIP水平显著降低;中药各剂量组、西药组大鼠纹状体DA、血清CCK及VIP水平明显均增加(P<0.01)。结论:龟羚帕安丸具有明显神经保护作用,作用机制与激活脑肠轴、增加血清CCK及VIP水平、增加中脑黑质纹状体DA的水平、发挥改善肠道功能作用有关。

采用非稳相偏振滤波的DAS-VSP数据P/S波分离方法及其应用

分布式光纤声学传感(DAS)因成本低、易布设以及高密度采样等优势正成为重要的地震观测技术,尤其是越来越多地与垂直地震剖面(VSP)结合,用于主动地震勘探或被动地震监测.DAS传感器通过感知弹性波场产生的轴向应变或应变速率来观测地震波场振动.然而,目前单分量DAS-VSP数据未完整地记录地下弹性波场的三维矢量振动信号,因此如何从中分离出P波或S波用于后续地震成像与参数反演是重要且很有挑战的课题.以弹性波传播理论为基础,本文根据P波和S波的频散关系估算接收点处各自的偏振方向,通过随频率和空间位置变化的偏振滤波实现DAS-VSP数据的P/S波分离.理论模型合成数据与东海实际DAS-VSP数据实验结果表明,该方法能有效地将P波和S波信号从单分量DAS-VSP数据中分离出来,可为后续纵横波速度反演、PP与PS波成像提供关键的数据预条件处理.

Active Damping of Milling Vibration Using Operational Amplifier Circuit

The problem of chatter vibration is associated with adverse consequences that often lead to tool impairment and poor surface finished in a workpiece, and thus, controlling or suppressing chatter vibrations is of great significance to improve machining quality. In this paper, a workpiece and an actuator dynamics are considered in modeling and controller design. A proportional-integral controller(PI) is presented to control and actively damp the chatter vibration of a workpiece in the milling process. The controller is chosen on the basis of its highly stable output and a smaller amount of steady-state error. The controller is realized using analog operational amplifier circuit. The work has contributed to planning a novel approach that addresses the problem of chatter vibration in spite of technical hitches in modeling and controller design. The method can also lead to considerable reduction in vibrations and can be beneficial in industries in term of cost reduction and energy saving. The application of this method is verified using active damping device actuator(ADD) in the milling of steel.

基于SDRS数据的钻石DA20飞机故障分析及处理

基于使用困难报告系统(SDRS)对钻石DA20飞机的故障数据进行分析。基于SDRS系统收集到的数据,结合故障分类方法,对钻石DA20飞机的不同故障进行研究,并提出相应的解决措施,有利于提高钻石DA20飞机机队的可靠性和安全性。

Adaptive Digital Predistortion Schemes to Linearize RF Power Amplifiers with Memory Effects

To compensate for nonlinear distortion introduced by RF power amplifiers （PAs） with memory effects, two correlated models, namely an extended memory polynomial （EMP） model and a memory lookup table （LUT） model, are proposed for predistorter design. Two adaptive digital predistortion （ADPD） schemes with indirect learning architecture are presented. One adopts the EMP model and the recursive least square （RLS） algorithm, and the other utilizes the memory LUT model and the least mean square （LMS） algorithm. Simulation results demonstrate that the EMP-based ADPD yields the best linearization performance in terms of suppressing spectral regrowth. It is also shown that the ADPD based on memory LUT makes optimum tradeoff between performance and computational complexity.

High-Gm Differential Regulated Cascode Transimpedance Amplifier

A differential cross-coupled regulated cascode(RGC)transimpedance amplifier(TIA)is proposed. The theory of multi-stage common-source(CS) configuration as an auxiliary amplifier to enhance the bandwidth and output impedance of RGC topology is analyzed. Additionally, negative Miller capacitance and shunt active inductor compensation are exploited to further expand the bandwidth. The proposed RGC TIA is simulated based on UMC 0.18 μm standard CMOS process. The simulation results demonstrate that the proposed TIA has a high transimpedance of 60.5 d B?, and a-3 d B bandwidth of 5.4 GHz is achieved for 0.5 p F input capacitance. The average equivalent input noise current spectral density is about 20 p A/Hz^(1/2) in the interested frequency, and the TIA consumes 20 m W DC power under 1.8 V supply voltage. The voltage swing is 460 m V pp, and the saturation input current is 500 μA.

Adaptive Polarization Control of Fiber Amplifier Based on SPGD Algorithm

We demonstrate an adaptive polarization control system of a 10.2 W non-polarization-maintaining fiber amplifier based on stochastic parallel gradient decent(SPGD)algorithm.The experimental investigation shows that the system can used to compensate for the polarization fluctuation of the fiber amplifier effectively and perform well over a long-time observation.When the adaptive polarization control system is in closed loop,the extinction ratio increases from 2.28 dB to 11.54 dB,and more than 93.4%of the total power in desired polarization direction is achieved.

A 58-dBΩ20-Gb/s inverter-based cascode transimpedance amplifier for optical communications

This work presents a high-gain broadband inverter-based cascode transimpedance amplifier fabricated in a 65-nm CMOS process.Multiple bandwidth enhancement techniques,including input bonding wire,input series on-chip inductive peak-ing and negative capacitance compensation,are adopted to overcome the large off-chip photodiode capacitive loading and the miller capacitance of the input device,achieving an overall bandwidth enhancement ratio of 8.5.The electrical measure-ment shows TIA achieves 58 dBΩup to 12.7 GHz with a 180-fF off-chip photodetector.The optical measurement demonstrates a clear open eye of 20 Gb/s.The TIA dissipates 4 mW from a 1.2-V supply voltage.

Adaptive Quasi-PID Control Method for Switching Power Amplifiers

Quasi-PID control method that is able to effectively inhibit the inherent tracking error of PI control method is proposed on the basis of a rounded theoretical analysis of a model of switching power amplifiers (SPAs). To avoid the harmful impacts of the circuit parameter variations and the random disturbances on quasi-PID control method, a single neuron is introduced to endow it with self-adaptability. Quasi-PID control method and the single neuron combine with each other perfectly, and their formation is named as single-neuron adaptive quasi-PID control method. Simulation and experimental results show that single-neuron adaptive quasi-PID control method can accurately track both the predictable and the unpredictable waveforms. Quantitative analysis demonstrates that the accuracy of single-neuron adaptive quasi-PID control method is comparable to that of linear power amplifiers (LPAs) and so can fulfill the requirements of some high-accuracy applications, such as protective relay test. Such accuracy is very difficult to be achieved by many modern control methods for converter controls. Compared with other modern control methods, the programming realization of single-neuron adaptive quasi-PID control method is more suitable for real-time applications and realization on low-end microprocessors for its simple structure and lower computational complexity.

A virtual lock-in amplifier,spectrum analyzer,impedance meter and semiconductor analyzer implemented on an SR7265 hardware target

Lock-in amplifiers are used to detect and measure very small alternating current(AC)signals down to the range of nVs.Accurate measurements can be made even when the small signals are buried by noise thousands of times larger.With the digital signal processing(DSP)technology involved in modern instrumentation,a lock-in amplifier is more versatile in sensing and recovering small signals.Combining the virtual instrumentation technology,we reorganize the functional blocks of a programmable lock-in amplifier and build it as a virtual spectrum analyzer,virtual impedance meter,virtual network analyzer,virtual semiconductor parameter analyzer,signal generator,etc.A 4 layer model is used to implement these virtual instruments.The same virtual instrument can also be implemented on a general purpose FPGA developing board.

Optical Pulse Compression Based on High-doped Erbium Fiber Amplifier and Standard Single-mode Fiber

Proposed is a novel optical pulse compression technique based on high-doped erbium fiber amplifier and standard single-mode fiber(SMF). We used the amplifier with the erbium ion concentration of 6.3×10-3 to amplify a hyperbolic secant pulse from a regeneratively mode-locked fiber laser. The central wavelength, pulsewidth and peak power of the pulse are 1 550 nm, 12.5 ps and 3 mW, respectively. Then the amplified pulse with peak power level corresponding to a higher-order soliton is compressed when it propagates through a 3-km-long single-mode fiber. Studied are the compressed pulses under different pump powers and fiber lengths. The results show that it can get a narrower pulse, and solve the difficulty that pulses at low power can not be compressed directly in the fiber. And the construct is compact.

Adaptation of a Digitally Predistorted RF Amplifier Using Selective Sampling

In this paper, a reduced-cost method of measuring residual nonlinearities in an adaptive digitally predistorted amplifier is proposed. Measurements obtained by selective sampling of the amplifier output are integrated over the input envelope range to adapt a fourth-order polynomial predistorter with memory correction. Results for a WCDMA input with a 101 carrier configuration show that a transmitter using the proposed method can meet the adjacent channel leakage ratio （ACLR） specification. Inverse modeling of the nonlinearity is proposed as a future extension that will reduce the cost of the system further.

Design of Low Voltage, Low Power (IF) Amplifier Based-On MOSFET Darlington Configuration

This paper presents a different approach of Intermediate Frequency (IF) amplifier using 0.18 μm MIETEC technology channel length of MOSFET Darlington transistors. In contrast to Bipolar conventional Darlingtonpair, a MOSFET Darlington configuration is employed to reduce supply voltage (VDD) and DC consumption power (Pc). The frequency response parameters of the proposed design such as bandwidth, gain bandwidth product, input/output noises and noise figure (NF) are improved in proposed (IF) amplifier. Moreover, a dual-input and dual-output (DIDO) IF amplifier constructed from two symmetrical single input and single output (SISO) (IF) amplifier is proposed too. The idea is to achieve improved bandwidth, and flat response, because these parameters are very important in high frequency applications. Simulation results that obtained by P-SPICE program are 1.2 GHz Bandwidth (BW), 3.4 GHz (gain bandwidth product), 0.5 mW DC consumption power (Pc) and the low total output noise is 12 nV with 1.2 V single supply voltage.

An X-Band Low Noise Amplifier Design for Marine Navigation Radars

In this paper, the design of a 9.1 GHz Low Noise Amplifier (LNA) of a RADAR receiver that is used in the Navy is presented. For the design of the LNA, we used GaAs Field-Effect Transistors (FETs) from Agilent ADS component library. In order to keep the cost of the circuit in low prices and the performance high, we design a two-stage LNA.

A 40-Gbit/s 1-to-2 Photonic Data Distributor Employing a Single Semiconductor Optical Amplifier

A simple design of 1-to-2 photonic data distributor is proposed.A proof-of-concept experiment is performed at 40 Gbit/s employing four-wave mixing and cross gain modulation in a single semiconductor optical amplifier.Correct output logic signals with high extinction ratios(over 11 dB)and clear open eyes are obtained,without using any additional input light beam.The scheme would be a promising candidate for future ultrafast all-optical signal processing applications.