High-Power Raman Soliton Generation at 1.7 μm in All-Fiber Polarization-Maintaining Erbium-Doped Amplifier

An all-fiber polarization maintaining high-power laser system operating at 1.7 μm based on the Ramaninduced soliton self-frequency shifting effect is demonstrated. The entirely fiberized system is built by erbiumdoped oscillator and two-stage amplifiers with polarization maintaining commercial silica fibers and devices, which can provide robust and stable soliton generation. High-power soliton laser with the average power of 0.28 W,the repetition rate of 42.7 MHz, and pulse duration of 515 fs is generated directly from the main amplifier.Our experiment provides a feasible method for high-power all-fiber polarization maintaining femtosecond laser generation working at 1.7 μm.

Broadband Dual-Input Doherty Power Amplifier Design Based on a Simple Adaptive Power Dividing Ratio Function

In this paper,a simple adaptive power dividing function for the design of a dual-input Doherty power amplifier(DPA)is presented.In the presented approaches,the signal separation function(SSF)at different frequency points can be characterized by a polynomial.And in the practical test,the coefficients of SSF can be determined by measuring a small number of data points of input power.Same as other dualinput DPAs,the proposed approach can also achieve high output power and back-off efficiency in a broadband operation band by adjusting the power distribution ratio flexibly.Finally,a 1.5-2.5 GHz highefficiency dual-input Doherty power amplifier is implemented according to this approach.The test results show that the peak power is 48.6-49.7d Bm,and the 6-d B back-off efficiency is 51.0-67.0%,and the saturation efficiency is 52.4-74.6%.The digital predistortion correction is carried out at the frequency points of 1.8/2.1GHz,and the adjacent channel power ratio is lower than-54.5d Bc.Simulation and experiment results can verify the effectiveness and correctness of the proposed method.

Harmonic balance simulation of the influence of component uniformity and reliability on the performance of a Josephson traveling wave parametric amplifier

A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.

A Hybrid Integrated and Low-Cost Multi-Chip Broadband Doherty Power Amplifier Module for 5G Massive MIMO Application

In this paper,a hybrid integrated broadband Doherty power amplifier(DPA)based on a multi-chip module(MCM),whose active devices are fabricated using the gallium nitride(GaN)process and whose passive circuits are fabricated using the gallium arsenide(GaAs)integrated passive device(IPD)process,is proposed for 5G massive multiple-input multiple-output(MIMO)application.An inverted DPA structure with a low-Q output network is proposed to achieve better bandwidth performance,and a single-driver architecture is adopted for a chip with high gain and small area.The proposed DPA has a bandwidth of 4.4-5.0 GHz that can achieve a saturation of more than 45.0 dBm.The gain compression from 37 dBm to saturation power is less than 4 dB,and the average power-added efficiency(PAE)is 36.3%with an 8.5 dB peak-to-average power ratio(PAPR)in 4.5-5.0 GHz.The measured adjacent channel power ratio(ACPR)is better than50 dBc after digital predistortion(DPD),exhibiting satisfactory linearity.

Three-channel CMOS transimpedance amplifier for LiDAR sensor receiver

For time-of-flight(TOF)light detection and ranging(LiDAR),a three-channel high-performance transimpedance amplifier(TIA)with high immunity to input load capacitance is presented.A regulated cascade(RGC)as the input stage is at the core of the complementary metal oxide semiconductor(CMOS)circuit chip,giving it more immunity to input photodiode detectors.A simple smart output interface acting as a feedback structure,which is rarely found in other designs,reduces the chip size and power consumption simultaneously.The circuit is designed using a 0.5μm CMOS process technology to achieve low cost.The device delivers a 33.87 dB?transimpedance gain at 350 MHz.With a higher input load capacitance,it shows a-3 dB bandwidth of 461 MHz,indicating a better detector tolerance at the front end of the system.Under a 3.3 V supply voltage,the device consumes 5.2 mW,and the total chip area with three channels is 402.8×597.0μm2(including the test pads).

5G Wideband Bandpass Filtering Power Amplifiers Based on a Bandwidth-Extended Bandpass Matching Network

In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.

Design and performance of a high-speed and low-noise preamplifier for SiPM

Considering the R&D for upgrading the K^(0)_(L) andμdetectors in the Belle II experiment using a scintillator and silicon pho-tomultiplier(SiPM),we designed a compact high-speed and low-noise preamplifier.The preamplifier demonstrated a good gain stability,bandwidth of 426 MHz,baseline noise level ofσ≈0.6 mV,dynamic range of up to170 mV of the input signal amplitude,good time resolution of 20 ps,and it can be comprehensively applied to SiPMs.Adopting pole-zero-cancelation in the preamplifier reduces both the rise and fall times of the SiPM signal,which can significantly improve the time resolution and reduce the pile-up when using a large SiPM or an array of SiPMs.Various combinations of the preamplifier and several types of SiPMs demonstrated time resolutions better than 50 ps for most cases;when the number of detected photons was larger than 60,a time resolution of approximately 25 ps was achieved.

Impact of amplified spontaneous emission noise on the SRS threshold of high-power fiber amplifiers

Impact of amplified spontaneous emission(ASE)noise on the stimulated Raman scattering(SRS)threshold of highpower fiber amplifiers is demonstrated numerically through a spectral evolution approach.The simulation results confirm that ASE noise in the Raman wavelength band could reduce the SRS threshold of high-power fiber amplifiers significantly.As for ASE noise originated the main amplifier,it becomes stronger and reduces the SRS threshold at shorter operation wavelength below 1052 nm.As for ASE noise originated from the seed laser,it reduces the SRS threshold at different operation wavelength under the condition that the Raman ratio is over-90 dB in the seed laser.The theoretical method and results in this work could provide a well reference to extend the operation wavelength of high-power fiber lasers.

Improving source-in-the-middle continuous-variable quantum key distribution using a heralded hybrid linear amplifier

A hybrid linear amplifier is inserted at the output of the source-in-the-middle distribution protocol to overcome the shortcomings of the transmission distance.The modified protocol aims to maintain a high key rate for long-distance transmission under high noise.It has the potential to significantly broaden the application range of the continuous variable quantum key distribution protocol.The effects of amplifier parameters and noise on the modified protocol are analyzed in detail with regard to applying it to a practical system.To make the simulation more realistic,the effect of finite size on the new protocol is taken into account.It will serve as a guideline for the future use of hybrid linear amplifiers.Different parameters can be adjusted to achieve the best performance for key rates of different quantum channels.

Piezomagnetic vibration energy harvester with an amplifier

We study the effect of an amplification mechanism in a nonlinear vibration energy harvesting system where a ferromagnetic beam resonator is attached to the vibration source through an additional linear spring with a damper.The beam moves in the nonlinear double-well potential caused by interaction with two magnets.The piezoelectric patches with electrodes attached to the electrical circuit support mechanical energy transduction into electrical power.The results show that the additional spring can improve energy harvesting.By changing its stiffness,we observed various solutions.At the point of the optimal stiffness of the additional spring,the power output is amplified a few times depending on the excitation amplitude.

Channel Pre-emphasis Equalization for a 270km 40×40 Gbit/s WDM System with Cascaded EDFAs/Raman Amplifiers

Optical channel pre-emphasis equalization is experimentally researched for a 270 km 40 × 40 Gbit/s wavelength division multiplexing （WDM） transmission system with three Erbium-doped fiber amplifiers （ED- FAs） and Raman amplifiers concatenated as booster amplifier. The channel imbalance of the overall system changes with different sets of power launched into EDFAs. By appropriately choosing the power input to concatenated EDFAs, the output spectrum of 40 channel signal can be equalized to the most extent. The merit of benefit can be around 5.5 dB by this pre-emphasis equalization. The requirement for the gain equalizer is therefore greatly released. Then the gain imbalance of the overall system and the power imbalance of 40 channels are compared and the two almost matches, but the significant difference lies on some channels. Finally, the pump power into Raman amplifier is also optimized, and another 1.3 dB improvement of channel equaliza- tion can be further achieved.

Research Towards Terahertz Power Amplifiers in Silicon-Based Process

In view of the existing design challenges for Terahertz(THz)power amplifiers(PAs),the common design methods and the efforts of the State Key Laboratory of Millimeter Wave,Southeast University,China in the development of silicon-based THz PAs,mainly including silicon-based PAs with operating frequencies covering 100–300 GHz,are summarized in this paper.Particularly,we design an LC-balun-based two-stage differential cascode PA with a center frequency of 150 GHz and an output power of 14 dBm.Based on a Marchand balun,we report a 220 GHz three-stage differential cascode PA with a saturated output power of 9.5 dBm.To further increase the output power of THz PA,based on a four-way differential power combining technique,we report a 211–263 GHz dual-LC-tank-based broadband PA with a recorded 14.7 dBm Psat and 16.4 dB peak gain.All the above circuits are designed in a standard 130 nm silicon germanium(SiGe)BiCMOS process.

Vertical vibration control using nonlinear energy sink with inertial amplifier

To reduce additional mass, this work proposes a nonlinear energy sink(NES)with an inertial amplifier(NES-IA) to control the vertical vibration of the objects under harmonic and shock excitations. Moreover, this paper constructs pure nonlinear stiffness without neglecting the gravity effect of the oscillator. Both analytical and numerical methods are used to evaluate the performance of the NES-IA. The research findings indicate that even if the actual mass is 1% of the main oscillator, the NES-IA with proper inertia angles and mass distribution ratios can still effectively attenuate the steady-state and transient responses of the main oscillator. Nonlinear stiffness and damping also have important effects. Due to strongly nonlinear factors, the coupled system may exhibit higher branch responses under harmonic excitation. In shock excitation environment, the NES-IA with a large dynamic mass can trigger energy capture of both main resonance and high-frequency resonance. Furthermore, the comparison with the traditional NES also confirms the advantages of the NES-IA in overcoming mass dependence.

Nonlinear Absorption and Low-threshold Two-photon Pumped Amplified Stimulated Emission from FAPbBr_(3) Nanocrystals

Formamidinium lead bromide(FAPbBr_(3))nanocrystals(NCs)have been considered to be a good optoelectronic material due to their pure green emission,excellent stability and superior carrier transport characteristics.However,two-photon pumped amplified spontaneous emission(ASE)and the corresponding nonlinear optical properties of FAPbBr_(3) NCs are scarcely revealed.Herein,we synthesized colloidal FAPbBr_(3) NCs with different sizes by changing the molar ratio of FABr/PbBr_(2) in the precursor solution,using ligand assisted precipitation(LARP)technology at room temperature.Photoluminescence(PL)and time resolved photoluminescence(TRPL)spectroscopy were measured to characterize their ASE properties.And their nonlinear optical properties were studied through the Zscan technique and the two-photon excited fluorescence method.The stimulated emission properties including oneand two-photon pumped ASE have been realized from FAPbBr_(3) NCs.With large two-photon absorption coefficient(0.27 cm/GW)and high non-linear absorption cross-section(7.52×10^(5) GM),ASE with threshold as low as 9.8μJ/cm^(2) and 487μJ/cm^(2) have been obtained from colloidal FAPbBr_(3) NCs using one-and two-photon excitations.These results indicate that as a new possible green-emitting frequency-upconversion material with low thresholds,FAPbBr_(3) NCs hold great potential in the development of high-performance two-photon pump lasers.

EDFA的原理分析及应用探究

互联网信息技术迅猛发展,传统的光电转换技术一定程度上已无法满足现代电信传输的要求。掺铒光纤放大器(EDFA)在泵浦光的作用下可以直接放大光信号,适用于现代光纤通信。该文分析了EDFA的基本原理,探究了EDFA技术的应用及发展趋势。

基于FPGA和ARM架构的EDFA平台方案

EDFA (Erbium Doped Fiber Amplifier)多应用于光纤通讯网络中,特定的应用场景和模式需要其硬件控制为相对独立的智能化嵌入式设备,文中提出了一种基于FPGA(现场可编程门阵列)和ARM(精简命令集处理器)结构的嵌入式EDFA控制平台。依靠ARM对FPGA做配置处理,FPGA作为内部模块的核心处理器,通过调用FPGA内嵌的NIOS内核,完成对EDFA的各驱动电路的高速并行处理,同时又对EDFA平台的工作原理和硬件结构进行阐述,并详细介绍了此平台的各个硬件功能模块。

Step memory polynomial predistorter for power amplifiers with memory

To reduce the number of digital predistortion coefficients, a step memory polynomial （SMP）predistorter is presented. The number of predistortion coefficients is decreased by adjusting the maximum nonlinear order for different memory orders in the traditional memory polynomial （MP）predistorter. The proposed SNIP predistorter is identified by an offline learning structure on which the coefficients can be extracted directly from the sampled input and output of a PA. Simulation results show that the SMP predistorter is not tied to a particular PA model and is, therefore, robust. The effectiveness of the SMP predistorter is demonstrated by simulations and experiments on an MP model, a parallel Wiener model, a Wiener-Hammerstein model, a sparsedelay memory polynomial model and a real PA which is fabricated based on the Freescale LDMOSFET MRF21030. Compared with the traditional MP predistorter, the SMP predistorter can reduce the number of coefficients by 60%.

Single Event Transients of Operational Amplifier and Optocoupler

The single event transient effects of the operational amplifier LM124J and the optocoupler HCPL 5231 are investigated by a pulsed laser test facility. The relation of transient pulse shape to pulsed laser equivalent LET is tested,the sensitive areas of the SET effects are identified in voltage follower application mode of LM124J, and the mechanism is initially analyzed. The transient amplitude and duration of HCPL5231 at various equivalent LET are examined,and the SET cross-section is measured. The results of our test and heavy ion experimental data coincide closely,indicating that a pulsed laser test facility is a valid tool for single event effect evaluation.

All-Optical Sampling Using Nonlinear Polarization Rotation in a Single Semiconductor Optical Amplifier

We propose a novel all-optical sampling method using nonlinear polarization rotation in a semiconductor optical amplifier. A rate-equation model capable of describing the all-optical sampling mechanism is presented in this paper. Based on this model, we investigate the optimized operating parameters of the proposed system by simulating the output intensity of the probe light as functions of the input polarization angle, the phase induced by the polarization controller, and the ori- entation of the polarization beam splitter. The simulated results show that we can obtain a good linear slope and a large linear dynamic range,which is suitable for all-optical sampling. The operating power of the pump light can be less than lmW. The presented all-optical sampling method can potentially operate at a sampling rate up to hundreds GS/s and needs low optical power.

SiGe HBT Class AB Power Amplifier for Wireless Communications

Good performance SiGe power amplifiers applicable to wireless communications are demonstrated.The output power can reach more than 30dBm in class B mode.And in class AB mode,the output power at 1dB compression point ( P 1dB ) is 24dBm,the output third order intercept (TOI) power is 39dBm under V cc of 4V.The highest power added efficiency (PAE) and PAE at 1dB compression point are 34% and 25%,respectively.The adjacent channel power rejection for CDMA signal is more than 42dBc,which complies with IS95 specification.