Effects of operational factors on soluble microbial products in a carrier anaerobic baffled reactor treating dilute wastewater

The effects of feed strength, hydraulic residence time （HRT）, and operational temperatures on soluble microbial product （SMP） production were investigated, to gain insights into the production mechanism. A carrier anaerobic baffled reactor （CABR） treating dilute wastewater was operated under a wide range of operational conditions, namely, feed strengths of 300-600 mg/L, HRTs of 9- 18 h, and temperatures of 10-28℃. Generally, SMP production increased with increasing feed strength and decreasing temperature. At high temperature （28℃）, SMP production increased with decreasing HRT. As the temperature was decreased to 18 and 10℃, the SMP production was at its peak for 12 h HRT. Therefore, temperature could be an important determinant of SMP production along with HRT. A higher SMP to soluble chemical oxygen demand （SCOD） ratio was found at high temperature and long HRT because of complete volatile fatty acid degradation. SMP accounted for 50%-75% of the SCOD in the last chamber of the CABR. As a secondary metabolite, some SMP could be consumed at lower feed strength.

Effects of Temperature and Hydraulic Residence Time (HRT) on Treatment of Dilute Wastewater in a Carrier Anaerobic Baffled Reactor

Objective To examine the effect of hydraulic residence time （HRT） on the performance and stability, to treat dilute wastewater at different operational temperatures in a carrier anaerobic baffled reactor （CABR）, and hence to gain a deeper insight into microbial responses to hydraulic shocks on the base of the relationships among macroscopic performance, catabolic intermediate, and microcosmic alternation. Methods COD, VFAs, and microbial activity were detected with constant feed strength （300 mg/L） at different HRTs （9-18 h） and temperatures （10℃-28℃） in a CABR. Results The removal efficiencies declined with the decreases of HRTs and temperatures. However, the COD removal load was still higher at short HRT than at long HRT. Devastating reactor performance happened at temperature of 10℃ and at HRT of 9 h. HRTs had effect on the VFAs in the reactor slightly both at high and low temperatures, but the reasons differed from each other. Microbial activity was sensitive to indicate changes of environmental and operational parameters in the reactor. Conclusion The CABR offers to certain extent an application to treat dilute wastewater under a hydraulic-shock at temperatures from 10℃to 28℃.

A review of modified and hybrid anaerobic baffled reactors for industrial wastewater treatment

This review discusses high-strength wastewater treatment using anaerobic baffled reactors(ABRs)and modified ABRs.The research findings and applications of ABRs in treating various types of high strength wastewater generated from food companies,livestock,and industries were summarized and reported.Measurement parameters affecting the performance of ABRs are briefly discussed.The state-of-the-art laboratory studies are compiled and critically reviewed.Critical challenges and suggestions for future investigation are also addressed.

Hydrodynamic characteristics of a four-compartment periodic anaerobic baffled reactor

Periodic anaerobic baffled reactor （PABR） is a novel reactor based on the design concept of anaerobic baffled reactor （ABR）. Residence time distribution （RTD） studies on both clean and working reactors at the same hydraulic residence time （HRT） of 2 d were carded out to investigate the dead spaces and mixing patterns in PABRs at different organic loading rates （OLRs） in various switching manners and frequencies. The results showed that the fraction of dead space in PABR was similar to that in ABR, which was low in comparison with other reactor designs. Dead space may be divided into two categories, hydraulic and biological. In RTD studies without biomass, the hydraulic dead space in the PABR run in an ＂every second＂ switching manner with T = 2 d was the lowest whereas that in the PABR run in a T = ∞ （ABR） switching manner was the highest. The same trend was obtained with the total dead space in RTD studies with biomass no matter what the OLR was. Biological dead space was the major contributor to dead space but affected decreasingly at higher OLR whichever switching manner the PABR run in. The flow patterns within the PABRs were intermediate between plug-flow and perfectly mixed under all the conditions tested,

Effects of hydraulic retention time, temperature, and effluent recycling on efficiency of anaerobic filter in treating rural domestic wastewater

With rural population expansion and improvement of the socio-economic standard of living, treatment of rural domestic wastewater has rapidly become a major aspect of environmental concern. Selection of a suitable method for treatment of rural domestic wastewater depends on its efficiency, simplicity, and cost-effectiveness. This study investigated the effects of hydraulic retention time （HRT）, temperature, and effluent recycling on the treatment efficiency of an anaerobic filter （AF） reactor. The first round of experimental operations was run for three months with HRTs of one, two, and three days, temperatures of 18℃, 21℃, and 24℃, and no effluent recycling. The second round of experimental operations was conducted for another three months with HRTs of three and four days; temperatures of 30.67℃, 30.57℃, and 26.91 ℃ ; and three effluent recycling ratios of 1：1, 1：2, and 2：1. The first round of operations showed removal rates of 32% to 44% for COD, 30% to 35% for TN, 32% to 36% for NH4-N, 19% to 23% for NO3-N, and 12% to 22% for TE In the second round of operations, the removal rates varied from 75% to 81% for COD, 35% to 41% for TN, 31% to 39% for NH4-N, 30% to 34% for NO3-N, and 41% to 48% for TP. The average gas production rates were 6.72 L/d and 7.26 L/d for the first and second rounds of operations, respectively. The gas production rate increased in the second round of operations as a result of applied effluent recycling. The best removal efficiency was obtained for an optimum HRT of three days, a temperature of 30℃, and an effluent recycling ratio of 2：1. The results show that the removal efficiency of the AF reactor was affected by HRT, temperature, and effluent recycling.

Application of Froude dynamic similitude in anaerobic baffled reactors to prediction of hydrodynamic characteristics of a prototype reactorusing a model reactor

An anaerobic baffled reactor is a system developed in recent decades and has been used as part of the treatment of high-strength wastewater. Since the function of this system is based on its hydrodynamic features, hydrodynamics and the regime of the flow through the reactor are crucial. In this study, a prototype reactor with eight chambers, which had a total volume of 48 L, and a model reactor, whose dimensions were half of those of the prototype reactor, were used. The Froude dynamic similitude in these reactors was investigated. The results show that the curve dimensionless variances were 0.089 and 0.096 for the prototype and model reactors, respectively, the short-circuiting indices were 0.483 and 0.489 for the prototype and model reactors, respectively, the effective volume and short-circuiting index measurement errors were both 1%, the hydraulic efficiency error was 2%, and the Peclet and dispersion number errors were both 7%. Most of the compared indices were close to one another in value. Therefore, the model reactor can be used based on the Froude dynamic similitude to determine hydrodynamic charac-teristics of a baffled reactor at a full scale.

Microbiological Characteristics of Anaerobic Granular Sludge in Hybrid Anaerobic Baffled Reactor

Anaerobic granular sludge is of key importance for highly effective operation of hybrid anaerobic baffled reactor(HABR).An observation and analysis on the composition of anaerobic granular sludge in each separation compartment of HABR was conducted by using scanning electron microscope(SEM)and molecular biotechnology,and specific methanogenic activity(SMA)and coenzyme F420 content were determined.It was indicated that the disparity of microbial composition was significant among these separation compartments of HABR,and the HABR encouraged phase separation.The results show the understanding of microbiological characteristics of anaerobic granular sludge in HABR is helpful for cultivating granular sludge,which ensures the effective operation of the reactor.

A novel approach to treat combined domestic wastewater and excess sludge in MBR

Domestic wastewater was treated by combined anaerobic biofilm aerobic membrane bioreactor(MBR) process, and part biomass in MBR was withdrawn to treat with ozone, then the ozonated sludge was returned to anaerobic inlet. In aerobic MBR, MLSS and DO were controlled at 3000—3500 mg/L and 0 8 mg/L respectively. Comparing the experimental results of two stages, it was noticed that ozonation did not affect the removal efficiency for organics but had a significant influence on the removals of NH 3 N and TN. During the ozonation period of two months, no excess sludge was wasted, and a zero sludge yield was obtained.

Hydraulic characteristics of an anaerobic baffled reactor as onsite wastewater treatment system

The feasibility of using anaerobic baffled reactor （ABR） as onsite wastewater treatment system was discussed. The ABR consisted of one sedimentation chamber and three up-flow chambers in series was experimented under different peak flow factors （PFF of 1 to 6）, superficial gas velocities （between 0.6 and 3.1 cm/hr） and hydraulic retention times （HRT） （24, 36 and 48 hr）. Residence time distribution （RTD） analyses were carded out to investigate the hydraulic characteristics of the ABR. It was found that the PFF resulted in hydraulic dead space. The dead space did not exceed 13% at PFF of 1, 2 and 4 while there was 2-fold increase （26%） at PFF of 6. Superficial gas velocities did not result in more （biological） dead space. The mixing pattern of ABR tended to be a completely- mixed reactor when PFF increased. Superficial gas velocities did not affect mixing pattern. The effects of PFF on mixing pattern could be minimized by higher HRT （48 hr）. The tank-in-series （TIS） model （N = 4） was suitable to describe the hydraulic behaviour of the studied system. The HRT of 48 hr was able to maintain the mixing pattern under different flow patterns, introducing satisfactory hydraulic efficiency. Chemical oxygen demand （COD） and total suspended solids （TSS） removals under all flow patterns were achieved more than 85% and 90%, respectively. The standard deviation of effluent COD and TSS concentration did not exceed 15 mg/L.

Pretreatment of coking wastewater using anaerobic sequencing batch reactor (ASBR)

A laboratory-scale anaerobic sequencing batch reactor (ASBR) was used to pretreat coking wastewater. Inoculated anaerobic granular biomass was acclimated for 225 d to the coking wastewater, and then the biochemical methane potential (BMP)of the coking wastewater in the acclimated granular biomass was measured. At the same time, some fundamental technological factors, such as the filling time and the reacting time ratio (tf/tr), the mixing intensity and the intermittent mixing mode, that affect anaerobic pretreatment of coking wastewater with ASBR, were evaluated through orthogonal tests. The COD removal efficiency reached 38％～50％ in the stable operation period with the organic loading rate of 0.37～0.54 kg COD/(m3.d) at the optimum conditions of tf/tr, the mixing intensity and the intermittent mixing mode. In addition, the biodegradability of coking wastewater distinctly increased after the pretreatment using ASBR. At the end of the experiment, the microorganism forms on the granulated sludge in the ASBR were observed using SEM (scanning electron microscope) and fluoroscope. The results showed that the dominant microorganism on the granular sludge was Methanosaeta instead of Methanosarcina dominated on the inoculated sludge.

Anaerobic-aerobic processes for the treatment of textile dyeing wastewater containing three commercial reactive azo dyes:Effect of number of stages and bioreactor type

In this study,the effect of number of stages and bioreactor type on the removal performance of a sequential anaerobic-aerobic process employing activated sludge for the treatment of a simulated textile dyeing wastewater containing three commercial reactive azo dyes was considered.Two stage processes performed better than one stage ones,both in terms of overall organic and color removal,as well as the higher contribution of anaerobic stage to the overall removal performance,thereby making them a more energy efficient option.The employment of a moving bed sequencing batch biofilm reactor,which uses both suspended and attached biomass,for the implementation of the anaerobic stage of the process,was compared with a sequencing batch reactor that only employs suspended biomass.The results showed that,although there was no meaningful difference in biomass concentration between the two bioreactors,the latter reactor had better performance in terms of chemical oxygen demand(COD)removal efficiency and rate and color removal rate.Further exploratory tests revealed a difference between the roles of suspended and attached bacterial populations,with the former yielding better color removal whilst the latter had better COD removal performance.The sequential anaerobic–aerobic process,employing an aerobic membrane bioreactor in the aerobic stage resulted in COD and color removal of 77.1±7.9%and 79.9±1.5%,respectively.The incomplete COD and color removal was attributed to the presence of soluble microbial products in the effluent and the autoxidation of dye reduction metabolites,respectively.Also,aerobic partial mineralization of the dye reduction metabolites,was experimentally observed.

Treatment of methanol wastewater in external circulation anaerobic reactor with different inoculums

In order to guide the inoculums selection for the anaerobic treatment of methanol wastewater in the engineering application,two 7 L bench-scale external circulation (EC) anaerobic reactors were operated to investigate the inoculums of anaerobic granular sludge and anaerobic digested sludge,focusing on the efficiency and process stability.The effect of impact concentration and temperature on the performance was studied.The results demonstrated that anaerobic granular sludge as the inoculums could complete the start-up more rapidly than the anaerobic digested sludge,and above 90% COD removal were achieved at the organic loading rate of 10 to 15 kgCOD/(m3·d).The effect of impact COD on the methanogenic activity of sludge was weak and the removal efficiencies recovered gradually in the two reactors.The COD removal efficiencies reduced swiftly to 50%-60% due to the impact temperature.The results indicated that the complex bacterial groups in anaerobic digested sludge benefited to enhance the reactor's capacity for withstanding the temperature shock at some extent.

Anaerobic Membrane Bioreactor as Highly Efficient and Reliable Technology for Wastewater Treatment—A Review

In this review paper, Anaerobic Membrane Bioreactor (AnMBR) is considering as highly efficient and reliable technology for organic material removal from wastewater with no additional energy requirement for aeration. AnMBR is a combination of conventional anaerobic technology and modern membrane system. AnMBR is cost effective alternative technology with pros of anaerobic microbial activity because Methogenic microorganism can convert organic pollutant load of wastewater into renewable energy in the form of methane rich biogas, this conversion is mainly done by transformation of organic matter into energy by high chemical oxygen demand (COD), total suspended solid (TSS) and pathogens removal. Methane rich biogas can be used as a storable source of supplemental energy for the production of heat or power thus AnMBR technology provides improved effluent quality, reliability, and efficiency over the other traditional technologies. This review paper is included the overview of AnMBR, the advantages over other wastewater treatment technology, operational constraints and the concerned factors that has affected the performances of implemented systems, applications of AnMBR for various types of wastewaters, research and development summary and future perspective for further research.

CHARACTERISTICS OF THERMOPHILIC ANAEROBIC ACIDOGENESIS OF STARCH WASTEWATER

Acidogenic dissimilation of synthetic starch wastewater (1 000～10 000 mg COD·L -1 ) was studied in a thermophilic (55 ℃) upflow anaerobic sludge blanket (UASB) reactor.The production of volatile fatty acids (VFA) was proportional to the chemical oxygen demand (COD) loading rate.The yield of VFA was around 0.28 g VFA/g COD over the COD loading rate from 1.25 to 30 g COD·L -1 ·d -1 and the hydraulic retention time from 8.8 h to 24 h.Distribution of organic acids,the contents of propionic and butyric acids in the effluent in particular were also dependent on the COD loading rate.The thermophilic UASB reactor showed a stable performance on hydrolysis and acidogenesis of starch as well as suspended solid removal at short hydraulic retention times and high influent pH(10～11),during the operation of 110 d.

Characteristics of high-sulfate wastewater treatment by two-phase anaerobic digestion process with Jet-loop anaerobic fluidized bed

A new anaerobic reactor, Jet-loop anaerobic fluidized bed （JLAFB）, was designed for treating high-sulfate wastewater. The treatment characteristics, including the effect of influent COD/SO42 ratio and alkalinity and sulfide inhibition in reactors, were discussed for a JLAFB and a general anaerobic fiuidized bed （AFB） reactor used as sulfate-reducing phase and methane-producing phase, respectively, in two-phase anaerobic digestion process. The formation of granules in the two reactors was also examined. The results indicated that COD and sulfate removal had different demand of influent COD/SO4^2- ratios. When total COD removal was up to 85%, the ratio was only required up to 1.2, whereas, total sulfate removal up to 95% required it exceeding 3.0. The alkalinity in the two reactors increased linearly with the growth of influent alkalinity. Moreover, the change of influent alkalinity had no significant effect on pH and volatile fatty acids （VFA） in the two reactors. Influent alkalinity kept at 400-500 mg/L could meet the requirement of the treating process. The JLAFB reactor had great advantage in avoiding sulfide and free-H2S accumulation and toxicity inhibition on microorganisms. When sulfate loading rate was up to 8. 1 kg/（m^3.d）, the sulfide and free-H2S concentrations in JLAFB reactor were 58.6 and 49.7 mg/L, respectively. Furthermore, the granules, with offwhite color, ellipse shape and diameters of 1.0-3.0 mm, could be developed in JLAFB reactor. In granules, different groups of bacteria were distributed in different layers, and some inorganic metal compounds such as Fe, Ca, Mg etc. were found.

Start-up and Performance of a Novel Reactor----Jet Biogas Inter-loop Anaerobic Fluidized Bed

A novel anaerobic reactor, jet biogas inter-loop anaerobic fluidized bed （JBILAFB）, was designed and constructed. The start-up and performance of the reactor was investigated in the Process. of .artificial glucose wastewater treatment. With the wastewater recycle ratio of 2.5 ： 1, the recycled wastewater with biogas could mix sludge and wastewater in the JBILAFB reactor completely. The start-up of the JBILAFB reactor could be completed in less than 70 d through maintenance of hydraulic retention time （HR^I＂） and stepwise increase of feed total organic carbon （TOC） concentration. After the start-up, with the volumetric TOC loadings of 14.3 kg·m ^-3·d^-1, the TOC removal ratio, the effluent pH, and the volatile fatty acids （VFA）/alkalinity of the JBILAFB reactor were more than 80%, close to 7.0 and less than 0.4, respectively. Moreover, CH4 was produced at more than 70% of the theoretical value, The reactor exhibited high stability under the condition of high volumetric TOC loading. Sludge granules in the JBILAFB reactor were developed during the start-up and their sizes were enlarged with the stepwise increase of volumetric TOC loadings from 0.8 kg.m^-3.d ^-1 to 14.3 kg.m^-3.d^-1. Granules, an offwhite color and a similar spherical shape, were mainly comprised of global-like bacteria. These had good methanogenic activity and settleability, which were formed probably through adhesion of the bacteria. Some inorganic metal compounds such as Fe, Ca, Mg, Al, etc. were advantageous to the formation of the granules.

Function of anaerobic portion in a conventional sequencing batch reactor

The performance of SBRs treating two kinds of wastewater(synthetic wastewater con- taining polyvinyl alcohol and effluent from a coke-plant wastewater treatment system)was investi- gated in this study,in order to examine the exact function of anaerobic portion in a conventional SBR.The set up of 4-or 8-hour anaerobic mixing period in a SBR's cycle did not benefit for PVA degradation.While an anaerobic reactor seeded with anaerobic sludge could partly hydrolyse and acidify PVA into readily-degradable intermediates.During the anaerobic fill period of an SBR treat- ing the effluent from a coke-plant wastewater treatment system,the organic concentration was re- duced to certain extent due to the adsorption of activated sludge and dilution of the mixed liquor from the previous cycle.Parts of readily-degradable organics in the influent were utilised by denitri- fiers as carbon source.The biomass in a conventional SBR was alternatively imposed to aerobic and anaerobic conditions in its operating cycle,the environmental conditions needed for anaerobic hy- drolization and acidification of refractory organics could not occur in such an SBR.

Treatment of methanol wastewater with two-stage and two-phase anaerobic process

The two-stage and two-phase anaerobic process (TSTP) composed of hydrolytic acidification reactor,first-order and second-order external circulation anaerobic reactors (EC) was taken to treat methanol wastewater. Test results show that TSTP process is quick start-up in 51 d, and the maximum VFA of hydrolytic acidification reactor effluent reaches 876 mg/L. Under the condition of volume loading of 6.56 kgCOD/m3·d, COD removal rate of the first-order EC reactor is about 85%, and under the condition of volume loading of 1.02 kgCOD/m3·d, COD removal rate of the second-order EC reactor is about 50%. When the inflow COD of TSTP process is between 7000-11000 mg/L, its effluent COD is lower than 600 mg/L. In the biological conversion process of methanol into methane,the production of acetic acids as an intermediate product can be ignored and the direct production of methane from methanol is predominant.

Performance and bioparticle growth of anaerobic baffled reactor （ABR） fed with low-strength domestic sewage

We investigated the performance of a 15.3 L capacity anaerobic baffled reactor （ABR） toward the treatment of low-strength domestic wastewater. The start- up period of the ABR was finished within approximately 130 days at a temperature below 25~C. The average CODcr in the effluent was 165 mg.L 1 and the corresponding CODcr removal efficiency of the ABR was 52.3%. During the third stage （from day 130 to day 233） of ABR operation, the average CODcr in the effluent reached 71 mg· L^-1, which meets the secondary discharge requirement of the Integrated Wastewater Discharge Standard （GB 18918-2002, China）. Moreover, partial microbial separa- tion was observed along the five ABR compartments through scanning electron microscopic images. The geometric mean diameter of bioparticles in the five compartments increased from 0.050 mm to 0.111, 0.107, 0.104, 0.110, and 0.103 mm during the start-up stage. After operation for 179days, the further increased to 0.376, corresponding diameters 0.225, 0.253, 0.239, and 0.288mm, respectively. The fractal dimensions of the bioparticles indicated that these particles have smoother surfaces and more compact structures during ABR operation. Morphological analysis of the bioparticle sections demonstrated that the bioparticles have a pore volume of 30%-55%. The highest porosity was observed for the bioparticles in the second ABR compartment, whereas the lowest fractal dimension ofbioparticle section was observed in the fifth compartment.

Effect of operational parameters on the performance of an anaerobic sequencing batch reactor(AnSBR)treating protein-rich wastewater

Treating protein-rich wastewater using cost-effective and simple-structured single-stage reactors presents several challenges.In this study,we applied an anaerobic sequencing batch reactor(AnSBR)to treat protein-rich wastewater from a slaughterhouse.We focused on identifying the key factors influencing the removal of chemical oxygen demand(COD)and the settling performance of the sludge.The AnSBR achieved a maximum total COD removal of 90%,a protein degradation efficiency exceeding 80%,and a COD to methane conversion efficiency of over 70%at organic loading rates of up to 6.2 g COD L^(-1)d^(-1).We found that the variations in both the organic loading rate within the reactor and the hydraulic retention time in the buffer tank had a significant effect on COD removal.The hydraulic retention time in the buffer tank and the reactor,which determined the ammonification efficiencies and the residual carbohydrate concentrations in the reactor liquid,affected the sludge settleability.Furthermore,the genus Clostridium sensu stricto 1,known as protein-and lipids-degraders,was predominant in the reactor.Statistical analysis showed a significant correlation between the core microbiome and ammonification efficiency,highlighting the importance of protein degradation as the governing process in the treatment.Our results will provide valuable insights to optimise the design and operation of AnSBR for efficient treatment of protein-rich wastewater.