New Fatigue Test and Statistical Method for Metallic Materials Used in Vehicle Transmissions

Aim To improve the efficiency of fatigue material tests and relevant statistical treatment of test data. Methods\ Least square approach and other special treatments were used. Results and Conclusion\ The concepts of each phase in fatigue tests and statistical treatment are clarified. The method proposed leads to three important properties. Reduced number of specimens brings to the advantage of lowering test expenditures. The whole test procedure has more flexibility for there is no need to conduct many tests at the same stress level as in traditional cases.

Modal Identification of Offshore Platforms Using Statistical Method Based on ERA

Identification of modal parameters of a linear structure with output-only measurements has received much attention over the past decades. In the paper, the Natural Excitation Technique (NExT) is used for acquisition of the impulse signals from the structural responses. Then Eigensystem Realization Algorithm (ERA) is utilized for modal identification. For disregarding the fictitious ‘computational modes', a procedure, Statistically Averaging Modal Frequency Method (SAMFM), is developed to distinguish the true modes from noise modes, and to improve the precision of the identified modal frequencies of the structure. An offshore platform is modeled with the finite element method. The theoretical modal parameters are obtained for a comparison with the identified values. The dynamic responses of the platform under random wave loading are computed for providing the output signals used for identification with ERA. Results of simulation demonstrate that the proposed method can determine the system modal frequency with high precision.

Statistical damage detection method for frame structures using a confidence interval

A novel damage detection method is applied to a 3-story frame structure, to obtain statistical quantification control criterion of the existence, location and identification of damage. The mean, standard deviation, and exponentially weighted moving average （EWMA） are applied to detect damage information according to statistical process control （SPC） theory. It is concluded that the detection is insignificant with the mean and EWMA because the structural response is not independent and is not a normal distribution. On the other hand, the damage information is detected well with the standard deviation because the influence of the data distribution is not pronounced with this parameter. A suitable moderate confidence level is explored for more significant damage location and quantification detection, and the impact of noise is investigated to illustrate the robustness of the method.

Evaluation of natural gas hydrate resources in the South China Sea using a new genetic analogy method

Natural gas hydrate(NGH)has attracted much attention as a new alternative energy globally.However,evaluations of global NGH resources in the past few decades have casted a decreasing trend,where the estimate as of today is less than one ten-thousandth of the estimate forty years ago.The NGH researches in China started relatively late,but achievements have been made in the South China Sea(SCS)in the past two decades.Thirty-five studies had been carried out to evaluate NGH resource,and results showed a flat trend,ranging from 60 to 90 billion tons of oil equivalent,which was 2-3 times of the evaluation results of technical recoverable oil and gas resources in the SCS.The big difference is that the previous 35 group of NGH resource evaluations for the SCS only refers to the prospective gas resource with low grade level and high uncertainty,which cannot be used to guide exploration or researches on development strategies.Based on the analogy with the genetic mechanism of conventional oil and gas resources,this study adopts the newly proposed genetic method and geological analogy method to evaluate the NGH resource.Results show that the conventional oil and gas resources are 346.29×10^(8)t,the volume of NGH and free dynamic field are 25.19×10^(4)km^(3) and(2.05-2.48)×10^(6)km^(3),and the total amount of in-situ NGH resources in the SCS is about(4.47-6.02)×10^(12)m^(3).It is considered that the resource of hydrate should not exceed that of conventional oil and gas,so it is 30 times lower than the previous estimate.This study provides a more reliable geological basis for further NGH exploration and development.

Statistical Monitoring Method for Pesticides and Harmful Substances

A statistical monitoring method has been developedfor accurate, safety surveillance methods of γ-BHC resideueor harmful substances in foods or feeds. It is very importantfor safety monitoring and arbitrament inspections. This paperintroduces a calculation formula by a six-point calibrationmethod and an example for detection of Y-BHC in corn.The method can guarantee the accuracy of the results,and it does very substantially reduce the probability of an er-ror by one-point calibration.

The efficiency and accuracy of probability diagram, spatial statistic and fractal methods in the identification of shear zone gold mineralization: a case study of the Saqqez gold ore district,NW Iran

In this study,geochemical anomaly separation was carried out with methods based on the distribution model,which includes probability diagram(MPD),fractal(concentration-area technique),and U-statistic methods.The main objective is to evaluate the efficiency and accuracy of the methods in separation of anomalies on the shear zone gold mineralization.For this purpose,samples were taken from the secondary lithogeochemical environment(stream sediment samples)on the gold mineralization in Saqqez,NW of Iran.Interpretation of the histograms and diagrams showed that the MPD is capable of identifying two phases of mineralization.The fractal method could separate only one phase of change based on the fractal dimension with high concentration areas of the Au element.The spatial analysis showed two mixed subpopulations after U=0 and another subpopulation with very high U values.The MPD analysis followed spatial analysis,which shows the detail of the variations.Six mineralized zones detected from local geochemical exploration results were used for validating the methods mentioned above.The MPD method was able to identify the anomalous areas higher than 90%,whereas the two other methods identified 60%(maximum)of the anomalous areas.The raw data without any estimation for the concentration was used by the MPD method using aminimum of calculations to determine the threshold values.Therefore,the MPD method is more robust than the other methods.The spatial analysis identified the detail soft hegeological and mineralization events that were affected in the study area.MPD is recommended as the best,and the spatial U-analysis is the next reliable method to be used.The fractal method could show more detail of the events and variations in the area with asymmetrical grid net and a higher density of sampling or at the detailed exploration stage.

Method“Monte Carlo”in healthcare

In public health,simulation modeling stands as an invaluable asset,enabling the evaluation of new systems without their physical implementation,experimentation with existing systems without operational adjustments,and testing system limits without real-world repercussions.In simulation modeling,the Monte Carlo method emerges as a powerful yet underutilized tool.Although the Monte Carlo method has not yet gained widespread prominence in healthcare,its technological capabilities hold promise for substantial cost reduction and risk mitigation.In this review article,we aimed to explore the transformative potential of the Monte Carlo method in healthcare contexts.We underscore the significance of experiential insights derived from simulated experimentation,especially in resource-constrained scenarios where time,financial constraints,and limited resources necessitate innovative and efficient approaches.As public health faces increasing challenges,incorporating the Monte Carlo method presents an opportunity for enhanced system construction,analysis,and evaluation.

Exploration of the Impact Mechanism of Government Credibility Based on Variable Screening Method

Government credibility is an important asset of contemporary national governance, an important criterion for evaluating government legitimacy, and a key factor in measuring the effectiveness of government governance. In recent years, researchers’ research on government credibility has mostly focused on exploring theories and mechanisms, with little empirical research on this topic. This article intends to apply variable selection models in the field of social statistics to the issue of government credibility, in order to achieve empirical research on government credibility and explore its core influencing factors from a statistical perspective. Specifically, this article intends to use four regression-analysis-based methods and three random-forest-based methods to study the influencing factors of government credibility in various provinces in China, and compare the performance of these seven variable selection methods in different dimensions. The research results show that there are certain differences in simplicity, accuracy, and variable importance ranking among different variable selection methods, which present different importance in the study of government credibility issues. This study provides a methodological reference for variable selection models in the field of social science research, and also offers a multidimensional comparative perspective for analyzing the influencing factors of government credibility.

An Application of the Adjoint Method to a Statistical-Dynamical Tropical-Cyclone Prediction Model （SD-90）Ⅱ：Real Tropical Cyclone Cases

In the first paper in this series, a variational data assimilation of ideal tropical cyclone （TC） tracks was performed for the statistical-dynamical prediction model SD-90 by the adjoint method, and a prediction of TC tracks was made with good accuracy for tracks containing no sharp turns. In the present paper, the cases of real TC tracks are studied. Due to the complexity of TC motion, attention is paid to the diagnostic research of TC motion. First, five TC tracks are studied. Using the data of each entire TC track, by the adjoint method, five TC tracks are fitted well, and the forces acting on the TCs are retrieved. For a given TC, the distribution of the resultant of the retrieved force and Coriolis force well matches the corresponding TC track, i.e., when a TC turns, the resultant of the retrieved force and Coriolis force acts as a centripetal force, which means that the TC indeed moves like a particle; in particular, for TC 9911, the clockwise looping motion is also fitted well. And the distribution of the resultant appears to be periodic in some cases. Then, the present method is carried out for a portion of the track data for TC 9804, which indicates that when the amount of data for a TC track is sufficient, the algorithm is stable. And finally, the same algorithm is implemented for TCs with a double-eyewall structure, namely Bilis （2000） and Winnie （1997）, and the results prove the applicability of the algorithm to TCs with complicated mesoscale structures if the TC track data are obtained every three hours.

Optimization of Rolling Process for Bi(2223)/Ag Superconducting Tapes by a Statistical Method

Ag-sheathed (Bi,Pb)(2)SoCa(2)Cu(3)O(x) tapes were prepared by the powder-in-tube method. The influences of rolling parameters on superconducting characteristics of Bi(2223)/Ag tapes were analyzed qualitatively with a statistical method. The results demonstrate that roll diameter and reduction per pass significantly influence the properties of Bi(2223)/Ag superconducting tapes while roll speed does less and working friction the least. An optimized rolling process was therefore achieved according to the above results.

Dynamic thermo-mechanical coupled simulation of statistically inhomogeneous materials by statistical second-order two-scale method

In this paper,a statistical second-order twoscale（SSOTS） method is developed to simulate the dynamic thcrmo-mechanical performances of the statistically inhomogeneous materials.For this kind of composite material,the random distribution characteristics of particles,including the shape,size,orientation,spatial location,and volume fractions,are all considered.Firstly,the repre.sentation for the microscopic configuration of the statistically inhomogeneous materials is described.Secondly,the SSOTS formulation for the dynamic thermo-mechanical coupled problem is proposed in a constructive way,including the cell problems,effective thermal and mechanical parameters,homogenized problems,and the SSOTS formulas of the temperatures,displacements,heat flux densities and stresses.And then the algorithm procedure corresponding to the SSOTS method is brought forward.The numerical results obtained by using the SSOTS algorithm are compared with those by classical methods.In addition,the thermo-mechanical coupling effect is studied by comparing the results of coupled case with those of uncoupled case.It demonstrates that the coupling effect on the temperatures,heat flux densities,displacements,and stresses is very distinct.The results show that the SSOTS method is valid to predict the dynamic thermo-mechanical coupled performances of statistically inhomogeneous materials.

THE STOCHASTIC BOUNDARY ELEMENT METHOD IN STATISTICAL ANALYSIS OF MODERATELY THICK PLATES

In this paper a stochastic boundary element method (SEEM) is developed to analyze moderately thick plates with random material parameters and random thickness. Based on the Taylor series expansion, the boundary integration equations concerning the mean and deviation of the generalized displacements are derived, respectively. It is found that the randomness of material parameters is equivalent to a random load, so the mean and covariance matrices of unknown generalized boundary displacements and tractions can be obtained. Furthermore, the mean and covariance of generalized displacements and forces at internal points can also be obtained. A numerical example has been worked out with the method proposed and necessary analysis is made for the results.

Problems and Recommendations for Rural Statistics and Survey Methods

With constant deepening of the reform and opening-up,national economic system has changed from planned economy to market economy,and rural survey and statistics remain in a difficult transition period. In this period,China needs transforming original statistical mode according to market economic system. All levels of government should report and submit a lot and increasing statistical information. Besides,in this period,townships,villages and counties are faced with old and new conflicts. These conflicts perplex implementation of rural statistics and survey and development of rural statistical undertaking,and also cause researches and thinking of reform of rural statistical and survey methods.

Causal inference and related statistical methods

Statistical approaches for evaluating causal effects and for discovering causal networks are discussed in this paper.A causal relation between two variables is different from an association or correlation between them.An association measurement between two variables and may be changed dramatically from positive to negative by omitting a third variable,which is called Yule-Simpson paradox.We shall discuss how to evaluate the causal effect of a treatment or exposure on an outcome to avoid the phenomena of Yule-Simpson paradox. Surrogates and intermediate variables are often used to reduce measurement costs or duration when measurement of endpoint variables is expensive,inconvenient,infeasible or unobservable in practice.There have been many criteria for surrogates.However,it is possible that for a surrogate satisfying these criteria,a treatment has a positive effect on the surrogate,which in turn has a positive effect on the outcome,but the treatment has a negative effect on the outcome,which is called the surrogate paradox.We shall discuss criteria for surrogates to avoid the phenomena of the surrogate paradox. Causal networks which describe the causal relationships among a large number of variables have been applied to many research fields.It is important to discover structures of causal networks from observed data.We propose a recursive approach for discovering a causal network in which a structural learning of a large network is decomposed recursively into learning of small networks.Further to discover causal relationships,we present an active learning approach in terms of external interventions on some variables.When we focus on the causes of an interest outcome, instead of discovering a whole network,we propose a local learning approach to discover these causes that affect the outcome.

The Continuous Analogy of Newton’s Method for Solving a System of Linear Algebraic Equations

We propose a continuous analogy of Newton’s method with inner iteration for solving a system of linear algebraic equations. Implementation of inner iterations is carried out in two ways. The former is to fix the number of inner iterations in advance. The latter is to use the inexact Newton method for solution of the linear system of equations that arises at each stage of outer iterations. We give some new choices of iteration parameter and of forcing term, that ensure the convergence of iterations. The performance and efficiency of the proposed iteration is illustrated by numerical examples that represent a wide range of typical systems.

Dynamic thermo-mechanical coupled response of random particulate composites:A statistical two-scale method

This paper focuses on the dynamic thermo-mechanical coupled response of random particulate composite materials. Both the inertia term and coupling term are considered in the dynamic coupled problem. The formulation of the problem by a statistical second-order two-scale （SSOTS） analysis method and the algorithm procedure based on the finite-element difference method are presented. Numerical results of coupled cases are compared with those of uncoupled cases. It shows that the coupling effects on temperature, thermal flux, displacement, and stresses are very distinct, and the micro- characteristics of particles affect the coupling effect of the random composites. Furthermore, the coupling effect causes a lag in the variations of temperature, thermal flux, displacement, and stresses.

Infant Mortality Rate Statistic Method and Difference Analysis in China

Infant mortality rate (IMR) has been viewed as the vital index which can be used to measure the health level of a country or a district, and also can indirectly illustrate the economic development level of the country or district. In this paper, the authors 1) introduce three calculation methods of IMR and compare the differences among them;2) calculate the IMR using one method above, and find the IMRs recorded in China Population Statistic Yearbook (CPSY) from National Statistics Institute and in China Health Statistic Yearbook from Ministry of National Hygiene are both overestimated;3) point out three main reasons for this overestimation: firstly, confusion of methods of calculation and concepts, secondly, inconsistent statistical caliber among different yearbooks, thirdly, flaws within the registration system.

Collecting Statistical Methods for the Analysis of Climate Data as Service for Adaptation Projects

The development of adaptation measures to climate change relies on data from climate models or impact models. In order to analyze these large data sets or an ensemble of these data sets, the use of statistical methods is required. In this paper, the methodological approach to collecting, structuring and publishing the methods, which have been used or developed by former or present adaptation initiatives, is described. The intention is to communicate achieved knowledge and thus support future users. A key component is the participation of users in the development process. Main elements of the approach are standardized, template-based descriptions of the methods including the specific applications, references, and method assessment. All contributions have been quality checked, sorted, and placed in a larger context. The result is a report on statistical methods which is freely available as printed or online version. Examples of how to use the methods are presented in this paper and are also included in the brochure.

A Statistical Comparison of Traffic Measurements from the Moving versus Stationary Observer Methods

Data of traffic flow, speed and density are required for planning, designing, and modelling of traffic stream for all parts of the road system. Specialized equipments such as stationary counts are used to record volume and speed;but they are expensive, difficult to set up, and require periodic maintenance. The moving observer method was proposed in 1954 by Wardrop and Charlesworth to estimate these variables inexpensively. Basically, the observer counts the number of vehicles overtaken, the number of vehicles passed, and the number of vehicles encountered while traveling in the opposite direction. The trip time is reported for both travel directions. Additionally, the length of road segment is measured. These variables are then used in estimating speeds and volumes. In a westbound direction from Interstate Highway 30 (I-30) in the DFW area, this study examined the accuracy and feasibility of this method by comparing it with stationary observer method as the standard method for such counts. The statistical tests were used to test the accuracy. Results show that this method provides accurate volume and speed estimates when compared to the stationary method for the road segment with three lanes per direction, especially when several runs are taken.

Research on the statistics index system and evaluation method of high and new technology industry development

During the evolution of the global economic, high and new technology industry has become the main driver to impel the global economy growth via technological advancement, and the main means to guarantee the sustainable development of the global economy. In the view of China’s situation, this article analyzes the experiences of OECD in high and new technology industry and gives a statistics index system along with the evaluation method to estimate the development of high and new technology industry.