Stress environment of entry driven along gob-side through numerical simulation incorporating the angle of break

Angle of break(AOB)is the acute angle created by the coal seam bedding plane and caving line formed by roof strata movement after extraction of a longwall panel.It has a significant influence on stress redistribution both in the gob and abutment.Throughout numerical simulation investigations up to now,little attention has been paid to it or an AOB of 90°was used,which however,is not realistic.This paper presents a detailed numerical modelling incorporating the AOB against Zhenchengdi Coal Mine.The AOB was obtained through cross-measure boreholes.Hoek-Brown constitutive model was used to simulate the rock masses.Double-yield constitutive model,which was best fitted by Salamon's model,was used to simulate the gob.The results show that a‘‘/\shape"shear failure zone develops around the gob.The shear failure in the floor along the panel edge is due to opposite shear of rock mass on two sides of the caving line,and the number of yielded zones within the gob floor close to the gob edge is smaller.According to the research,the entry was determined to be driven under the gob edge employing splitlevel longwall panel layout(SLPL).The other numerical simulation for SLPL shows that stress around the god-side entry is much smaller than pre-mining stress,and the area of intact rock mass at the elevating section is larger than conventional layout.Numerical modelling was then validated by field observation.

Numerical Simulation Study on the Surface Deflection of Cylindrical Shallow Shell

The increasing applications of new materials such as high strength low alloy (HSAL) steels and aluminum alloy sheets have lead to greater focus on the surface deflections of auto body panels in the automobile industry in recent years.The finite element models of cylindrical shallow shell that can represent auto body panels are established.Numerical simulations of forming and unloading of cylindrical shallow shell are carried out.And a measurement and evaluation method of the surface deflection is introduced.The simulations of surface deflections with various blank homing forces (BHF) show great agreement with the experi- mental results.The influence laws of sheet thickness and material properties such as yield strengthσs,strain-hardening exponent n,anisotropy parameter r and strength coefficient k on the surface deflection are achieved by simulations,which give a basic refer- ence for controlling surface deflections.

Numerical Simulation of Wake Deflection Control around NACA0012 Airfoil Using Active Morphing Flaps

This study demonstrates an active flow control for deflecting a direction of wake vortex structures behind a NACA0012 airfoil using an active morphing flap. Two-dimensional direct numerical simulations are performed for flows at the chord Reynolds number of 10,000, and the vortex pattern in the controlled and noncontrolled wakes as well as the effect of an actuation frequency on the control ability are rigorously investigated. It is found that there is an optimum actuation-frequency regime at around F + = 2.00 which is normalized by the chord length and freestream velocity. The wake vortex pattern of the well-controlled case is classified as the 2P wake pattern according to the Williamson’s categorization [1] [2], where the forced oscillation frequency corresponds to the natural vortex shedding frequency without control. The present classification of wake vortex patterns and finding of the optimum frequency regime in the wake deflection control can lead to a more robust design suitable for vortex-induced-vibration (VIV) related engineering systems.

Experimental and Three-Dimensional Numerical Simulation of Phenomena Induced by Submerged Oblique Jet Scouring

Scouring experiments were conducted using a three-dimensional laser scanning technology for angles of the jet spanning the interval from 0°to 30°,and the characteristics of the scour hole in equilibrium conditions were investigated accordingly.The results indicate that the optimal scouring effects occur when the jet angle is in the ranges between 15°and 20°.Moreover,the dimensionless profiles of the scour hole exhibit a high degree of similarity at different jet angles.Numerical simulations conducted using the Flow-3D software to investigate the bed shear stress along the jet impingement surface have shown that this stress is influenced by both the resultant force and the jet impingement surface area.It reaches its maximum value when the jet is vertical,decreases rapidly as the jet starts to tilt,then increases slightly,and decreases again significantly when the angle exceeds 20°.

Numerical study on gas production via a horizontal well from hydrate reservoirs with different slope angles in the South China Sea

It is important to study the effect of hydrate production on the physical and mechanical properties of low-permeability clayey–silty reservoirs for the largescale exploitation of hydrate reservoirs in the South China Sea.In this study,a multiphysical-field coupling model,combined with actual exploration drilling data and the mechanical experimental data of hydrate cores in the laboratory,was established to investigate the physical and mechanical properties of low-permeability reservoirs with different slope angles during 5-year hydrate production by the depressurization method via a horizontal well.The result shows that the permeability of reservoirs severely affects gas production rate,and the maximum gas production amount of a 20-m-long horizontal well can reach186.8 m3/day during the 5-year hydrate production.Reservoirs with smaller slope angles show higher gas production rates.The depressurization propagation and hydrate dissociation mainly develop along the direction parallel to the slope.Besides,the mean effective stress of reservoirs is concentrated in the near-wellbore area with the on-going hydrate production,and gradually decreases with the increase of the slope angle.Different from the effective stress distribution law,the total reservoir settlement amount first decreases and then increases with the increase of the slope angle.The maximum settlement of reservoirs with a 0°slope angle is up to 3.4 m,and the displacement in the near-wellbore area is as high as2.2 m after 5 years of hydrate production.It is concluded that the pore pressure drop region of low-permeability reservoirs in the South China Sea is limited,and various slope angles further lead to differences in effective stress and strain of reservoirs during hydrate production,resulting in severe uneven settlement of reservoirs.

Influence of Blade Wrap Angle on Centrifugal Pump Performance by Numerical and Experimental Study

The existing research on improving the hydraulic performance of centrifugal pumps mainly focuses on the design method and the parameter optimization. The traditional design method for centrifugal impellers relies more on experience of engineers that typically only satisfies the continuity equation of the fluid. In this study, on the basis of the direct and inverse iteration design method which simultaneously solves the continuity and motion equations of the fluid and shapes the blade geometry by controlling the wrap angle, three centrifugal pump impellers are designed by altering blade wrap angles while keeping other parameters constant. The three-dimensional flow fields in three centrifugal pumps are numerically simulated, and the simulation results illustrate that the blade with larger wrap angle has more powerful control ability on the flow pattern in impeller. The three pumps have nearly the same pressure distributions at the small flow rate, but the pressure gradient increase in the pump with the largest wrap angle is smoother than the other two pumps at the design and large flow rates. The pump head and efficiency are also influenced by the blade wrap angle. The highest head and efficiency are also observed for the largest angle. An experiment rig is designed and built to test the performance of the pump with the largest wrap angle. The test results show that the wide space of its efficiency area and the stability of its operation ensure the excellent performance of the design method and verify the numerical analysis. The analysis on influence of the blade wrap angle for centrifugal pump performance in this paper can be beneficial to the optimization design of the centrifugal pump.

Numerical simulation of dynamic process for liquid film spreading by lattice Boltzmann method and its experimental verification

Combined with the kinetic model of liquid film spreading, a new numerical method of solid-liquid-gas three-phase flow was developed for the moving of contact line, which was a hybrid method of computational fluid dynamics and lattice Boltzmalm method （LBM）. By taking the effect of molecule force in droplet and the wall surface on liquid film into account, the changing law of contact angle with different surface tensions was analyzed on glass and aluminum foil surfaces. Compared with experimental results, the standard deviation by using LBM is less than 0.5°, which validates the feasibility of LBM simulation on the dynamic process of liquid film spreading. In addition, oscillations are discovered both at the initial and end phases. The phenomenon of retraction is also found and the maximum retraction angle is 7.58°. The obtained result shows that the retraction is proved to be correlative with precursor film by tracking the volume change of liquid film contour. Furthermore, non-dimensional coefficient 2 is introduced to measure the liquid film retraction capacity.

NUMERICAL SIMULATION OF ORIENTATION DISTRIBUTION FUNCTION OF CYLINDRICAL PARTICLE SUSPENSIONS

The orientation distribution function of cylindrical particle suspensions was deduced and numerically simulated, and an application was taken in a wedge-shaped flow field. The relationship between the orientation distribution function and particle orientation angles was obtained. The results show that comparing with the most probable angle distribution which comes to being in short time, the distribution of the steady state doesn't vary much. in range; the main difference is the anti-clockwise rotation in the right and upper field, that is, particles rotate more at the points where the velocity gradients are larger. The most probable orientations are close to the direction of local streamlines. In the direction of streamlines, with poleradius decreasing, the most probable angles increase, but the angles between their orientations and the local streamlines decrease.

Effect of slope angle on fractured rock masses under combined influence of variable rainfall infiltration and excavation unloading

Intense precipitation infiltration and intricate excavation processes are crucial factors that impact the stability and security of towering and steep rock slopes within mining sites.The primary aim of this research was to investigate the progression of cumulative failure within a cracked rock formation,considering the combined effects of precipitation and excavation activities.The study was conducted in the Huangniuqian eastern mining area of the Dexing Copper Mine in Jiangxi Province,China.An engineering geological investigation was conducted,a physical model experiment was performed,numerical calculations and theoretical analysis were conducted using the matrix discrete element method(Mat-DEM),and the deformation characteristics and the effect of the slope angle of a fractured rock mass under different scenarios were examined.The failure and instability mechanisms of the fractured rock mass under three slope angle models were analyzed.The experimental results indicate that as the slope angle increases,the combined effect of rainfall infiltration and excavation unloading is reduced.A novel approach to simulating unsaturated seepage in a rock mass,based on the van Genuchten model(VGM),has been developed.Compared to the vertical displacement observed in a similar physical experiment,the average relative errors associated with the slope angles of 45,50,and 55were 2.094%,1.916%,and 2.328%,respectively.Accordingly,the combined effect of rainfall and excavation was determined using the proposed method.Moreover,the accuracy of the numerical simulation was validated.The findings contribute to the seepage field in a meaningful way,offering insight that can inform and enhance existing methods and theories for research on the underlying mechanism of ultra-high and steep rock slope instability,which can inform the development of more effective risk management strategies.

On the effect of pitch and yaw angles in oblique impacts of smallcaliber projectiles

A terminal ballistic analysis of the effects of 7.62 mm × 51 AP P80 rounds on inclined high-strength armor steel plates is the focus of the presented study.The findings of an instrumented ballistic testing combined with 3D advanced numerical simulations performed using the IMPETUS Afea? software yielded the conclusions.The experimental verification proved that slight differences in the pitch-andyaw angles of a projectile upon an impact caused different damage types to the projectile’s core.The residual velocities predicted numerically were close to the experimental values and the calculated core deviations were in satisfactory agreement with the experimental results.An extended matrix of the core deviation angles with combinations of pitch-and-yaw upon impact angles was subsequently built on the basis of the numerical study.The presented experimental and numerical investigation examined thoroughly the influence of the initial pitch and yaw angles on the after-perforation projectile’s performance.

Analysis of Influence on Aerodynamic Noise of Wind Turbine Blades under Different Pitch Angles

Aiming at the influence of blade pitch Angle on aerodynamic noise of wind turbines, the sound field and flow field distribution at 0˚, 5˚, 10˚ and 15˚ are calculated by numerical simulation. Then, through the distribution of pressure field and velocity field calculated by flow field, the influence of different pitch angles on wind turbine blade aerodynamic noise and the reasons for its influence are analyzed. The results show that when the pitch Angle increases within 0˚ - 10˚, the aerodynamic noise pressure level of the blade decreases. However, the sound pressure level of aerodynamic noise increases in the range of 10˚ - 15˚. The changes of static pressure gradient and pressure pulsation on the blade surface make the aerodynamic noise change, and the changes of the two are positively correlated. At the same time, the fluid velocity and fluid motion state on the blade surface are closely related to the aerodynamic noise of the blade. The greater the fluid velocity, the more complex the fluid motion state and the greater the turbulent kinetic energy of the wind turbine blade, and the aerodynamic noise of the wind turbine blade will also increase.

Numerical evaluation of the ground response induced by dewatering in a multi-aquifer system

This study presents a numerical investigation of dewatering-induced settlement and wall deflection during pumping tests in Tianjin,China.Based on the measured groundwater head and building settlement during the pumping test,a three-dimensional liquid-solid coupling model is established by using the finite element method(FEM).The void ratio,hydraulic conductivity,and elastic modulus of each layer are back-calculated through the numerical model.The groundwater drawdown,seepage field,ground settlement,horizontal ground displacement,and diaphragm wall lateral deflection are analyzed using the FEM model.The simulated results demonstrate that(i)the maximum ground settlement outside of the excavation reaches to 82 mm due to the leakage effect of aquitards;(ii)large horizontal displacement occurs in the soil during the pumping test with a maximum value of 28.3 mm,and the installation of the diaphragm wall in the aquifer can reduce the horizontal displacement of the ground;(iii)long-term pumping causes a large lateral deflection of the diaphragm wall,and a maximum value of 23.2 mm occurs at the layer where the screens of the wells are located;and(iv)long-term large-scale pumping should be avoided before excavation.

Effect of Cone Angle on the Hydraulic Characteristics of Globe Control Valve

Globe control valve is widely used in chemical, petroleum and hydraulic industries, and its throttling feature is achieved by the adopting of valve plug. However, very limited information is available in literature regarding the influence of valve plug on the internal and external features in globe control valves. Thus the effect of valve plug is studied by CFD and experiment in this paper. It is obtained from external features that the pressure drop between upstream and downstream pressure-sampling position increases exponentially with flow rate. And for small valve opening, the increment of pressure drop decreases with the increase of cone angle（β）. However, with the increase of valve opening, the effect of cone angle diminishes significantly. It is also found that the cone angle has little effect on flow coefficient（Cv） when the valve opening is larger than 70%. But for the cases less than 70%, Cv curve varies from an arc to a straight line. The variation of valve performance is caused by the change of internal flow. The results of internal flow show that cone angle has negligible effect on flow properties for the cases of valve opening larger than 70%. However, when valve opening is smaller than 70%, the pressure drop of orifice decreases with the increase of β, making the reduction in value and scope of the high speed zone around the conical surface of valve plug, and then results in a decreasing intensity of adjacent downstream vortex. Meanwhile, it is concluded from the results that the increase of cone angle will be beneficial for the anti-cavitation and anti-erosion of globe control valve. This paper focuses on the internal and external features of globe control valve that caused by the variation of cone angle, arriving at some results beneficial for the design and usage of globe control valve.

A Combined Experimental and Numerical Study of Shotcrete Jets and Related Wet Spray Nozzles

In this research,the dynamics of wet spray nozzles with different geometries,used to accelerate shotcrete,are investigated on the basis of a suitable three-dimensional mathematical model and related numerical method.Simulations have been conducted in the frame of the SIMPLEC algorithm.The k-εturbulence model has been used to account for turbulent effects.The study shows that when the angle of the convergent section is less than 3°,it has a scarce effect on the dynamics of the jet of shotcrete;with the increase of the convergence angle,the shotcrete jet velocity decreases and the nozzle wear increases;when this angle is greater than 6°,the concrete outlet jet velocity is very small and the nozzle can easily be blocked.Experimental results are in good agreement with the outcomes of the numerical simulations,which indicates that the used approach is reliable.

Effect of blade pitch angle on aerodynamic performance of straight-bladed vertical axis wind turbine

Wind energy is one of the most promising renewable energy sources, straight-bladed vertical axis wind turbine(S-VAWT) appears to be particularly promising for the shortage of fossil fuel reserves owing to its distinct advantages, but suffers from poor self-starting and low power coefficient. Variable-pitch method was recognized as an attractive solution to performance improvement, thus majority efforts had been devoted into blade pitch angle effect on aerodynamic performance. Taken into account the local flow field of S-VAWT, mathematical model was built to analyze the relationship between power outputs and pitch angle. Numerical simulations on static and dynamic performances of blade were carried out and optimized pitch angle along the rotor were presented. Comparative analyses of fixed pitch and variable-pitch S-VAWT were conducted, and a considerable improvement of the performance was obtained by the optimized blade pitch angle, in particular, a relative increase of the power coefficient by more than 19.3%. It is further demonstrated that the self-starting is greatly improved with the optimized blade pitch angle.

Influence of Wind Deviation Angle on n-Hexane Evaporation Loss of Internal Floating-Roof Tanks

With the increasing attention to environmental protection,it is still necessary to strictly control the oil evaporation loss from the IFRT(internal floating-roof tank)to the atmosphere.Upon using n-hexane as a representative of light oil,the effects of the WDAs(wind deviation angles)on airflow distribution,the wind speed,the n-hexane vapor concentration,and the evaporation loss rate in the IFRT were investigated,and the mass transfer of the vapor-air was analyzed.The results are shown as follows:when the WDA is 0°,the vapor concentration in the gas space above the floating deck is the lowest;when the WDA is 22.5°,the oil evaporation loss rate is the largest;when the WDA is 45°,the vapor concentration is the highest,but the evaporation loss rate is the smallest.It is recommended to arrange the vent to the wind direction with an angle of 45°to reduce the evaporation loss and protect the atmospheric environment.

Numerical study on hydraulic performance of submerged propellers in oxidation ditch

The submerged propeller is an efficient diving mix device,which is applicable for oxidation ditch treatment in industry,city and village wastewater-treatment plant. The impeller structure and reasonable rotating speed are important factors that determine flow field distribution and energy conversion efficiency. So it is necessary to use modern design methods to develop new kinds of high efficiency submerged propellers,and research the flow field characteristics of submerged propellers. On the basis of the existing form drawing,three-dimensional model of submerged propellers and unstructured tetrahedral mesh were generated. Based on Navier- Stokes equations and standard k- ε turbulence model,the flow was simulated by using a simple algorithm. Through changing some design parameters of propellers,the corresponding numerical simulation results reveal that for the same impeller diameter and service area of submerged propellers,the power consumption could be reduced effectively by optimizing blade mounting angle,which can determine the best blade mounting angle and most suitable rotational speed under given conditions. The study can provide theoretical and project guidance for submerged propellers design.

Effect of Free-fall Nozzle Channel Dispersion Angle on TC4 Discontinuous Droplets Pre-breakup in EIGA

The effect of the inlet gas pressure,supplementary gas pressure and nozzle channel dispersion angle on the pre-breakup behavior of Ti-6Al-4V(TC4)discontinuous droplets during EIGA was investigated by combining numerical simulation with experiments.The results show that the axial velocity at the recirculation zone before the stagnation location was first increased and decreased then increased significantly after the peak value,while the pressure of the recirculation zone increased with the increase in inlet pressure.With the supplementary pressure increasing,the velocity magnitude and range of the recirculation zone gradually decreased.As the dispersion angle of the nozzle channel increased,the pre-breakup efficiency of droplets gradually decreased,but the adhesion phenomenon of droplets on the inner wall surface of the nozzle channel(IWSNC)gradually weakened.Under the inlet pressure of 4 MPa,a supplementary pressure of 0.05 MPa,and the dispersion angle of 15°,the uniform and spherical TC4 powders with diameter of 70μm were prepared,which was consistent with the simulation results.The optimized process parameters is a balance between the size of the pre-atomized particles and the back-spraying and bonding phenomenons of droplets.

Effect of tapered angles in an artery on distribution of blood flow pressure with gravity considered

The tapered angles of an artery significantly influence the local hemodynamics. However, as gravity is considered, little is known about the effect of tapered angles on the hemodynamics. In this study, we explored whether the effect of tapered angles on the distribution of blood flow pressure (DBFP) differed with gravity considered or not. Numerical simulations of the DBFP in a single vessel were performed based on such tapered angles as 0°, 0.5° and 1°. In the model used for simulation, gravity was introduced as a body force. We obtained the following simulations: i) The larger the tapered angles were, the better distributed the blood flow pressure;ii) The tapered effect was an important factor leading to nonlinearity in blood flow pressure;iii) Gravity affected DBFP coupling with the tapered angles, yet independently influenced the dimension of the DBFP. At the same time, the effective intensity of gravity decreased with the increase of tapered angles.

Simulation of Vertical Solar Power Plants with Different Turbine Blades

The performances of turbine blades have a significant impact on the energy conversion efficiency of vertical solar power plants.In the present study,such a relationship is assessed by considering two kinds of airfoil blades,designed by using the Wilson theory.In particular,numerical simulations are conducted using the SST K−ω model and assuming a wind speed of 3–6 m/s and seven or eight blades.The two airfoils are the NACA63121(with a larger chord length)and the AMES63212;It is shown that the torsion angle of the former is smaller,and its wind drag ratio is larger;furthermore,the resistance is increased by about 66.3%on average.Within the scope of the study,the results show that the NACA63212 airfoil is better than the AMES63212 airfoil in terms of power,with an average improvement of about 2.8%.The simulation results have a certain guiding significance for selecting turbine blade airfoils and improving turbine efficiency.