Anisotropy effect on strengths of metamorphic rocks

This paper aims to study the effect of anisotropy on strengths of several metamorphic rocks of southern(Cine) submassif of Menderes metamorphic massif in southwest Turkey. Four different metamorphic rocks including foliated phyllite, schist, gneiss and marble(calcschist) were selected and examined.Discontinuity surveys were made along lines for each rock and evaluated with DIPS program. L-type Schmidt hammer was applied in the directions parallel and perpendicular to foliation during the field study. Several hand samples and rock blocks were collected during the field study for measurements of dry and saturated densities, dry and saturated unit weights and porosity, and for petrographic analysis and strength determination in laboratory. L-and N-type Schmidt hammers were applied in the directions perpendicular(anisotropy angle of 0°) and parallel(anisotropy angle of 90) to the foliation on selected blocks of phyllite, schist, gneiss and marble(calcschist). The phyllite and schist have higher porosity and lower density values than the other rocks. However, coarse crystalline gneiss and marble(calcschist) have higher rebound values and strengths, and they are classified as strong-very strong rocks. Generally, the rebound values in the direction perpendicular to the foliation are slightly higher than that in the direction parallel to foliation. Rebound values of N-type Schmidt hammer are higher than the L-type values except for phyllite. Sometimes, the rebound values of laboratory and field applications gave different results. This may result from variable local conditions such as minerals differentiation,discontinuities, water content, weathering degree and thickness of foliated structure.

A simplified approach to directly consider intact rock anisotropy in Hoek——Brown failure criterion

Many rock types have naturally occurring inherent anisotropic planes, such as bedding planes, foliation,or flow structures. Such characteristic induces directional features and anisotropy in rocks＇ strength anddeformational properties. The HoekeBrown （HeB） failure criterion is an empirical strength criterionwidely applied to rock mechanics and engineering. A direct modification to HeB failure criterion toaccount for rock anisotropy is considered as the base of the research. Such modification introduced a newdefinition of the anisotropy as direct parameter named the anisotropic parameter （Kb）. However, thecomputation of this parameter takes much experimental work and cannot be calculated in a simple way.The aim of this paper is to study the trend of the relation between the degree of anisotropy （Rc） and theminimum value of anisotropic parameter （Kmin）, and to predict the Kmin directly from the uniaxialcompression tests instead of triaxial tests, and also to decrease the amount of experimental work. 2014 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Production and hosting byElsevier B.V. All rights reserved.

A novel approach to structural anisotropy classification for jointed rock masses using theoretical rock quality designation formulation adjusted to joint spacing

Rock quality designation(RQD)has been considered as a one-dimensional jointing degree property since it should be determined by measuring the core lengths obtained from drilling.Anisotropy index of jointing degree(AI_(jd))was formulated by Zheng et al.(2018)by considering maximum and minimum values of RQD for a jointed rock medium in three-dimensional space.In accordance with spacing terminology by ISRM(1981),defining the jointing degree for the rock masses composed of extremely closely spaced joints as well as for the rock masses including widely to extremely widely spaced joints is practically impossible because of the use of 10 cm as a threshold value in the conventional form of RQD.To overcome this limitation,theoretical RQD(TRQD_(t))introduced by Priest and Hudson(1976)can be taken into consideration only when the statistical distribution of discontinuity spacing has a negative exponential distribution.Anisotropy index of the jointing degree was improved using TRQD_(t) which was adjusted to wider joint spacing by considering Priest(1993)’s recommendation on the use of variable threshold value(t)in TRQD_(t) formulation.After applications of the improved anisotropy index of a jointing degree(AI'_(jd))to hypothetical jointed rock mass cases,the effect of persistency of joints on structural anisotropy of rock mass was introduced to the improved AI'_(jd) formulation by considering the ratings of persistency of joints as proposed by Bieniawski(1989)’s rock mass rating(RMR)classification.Two real cases were assessed in the stratified marl and the columnar basalt using the weighted anisotropy index of jointing degree(W_AI'_(jd)).A structural anisotropy classification was developed using the RQD classification proposed by Deere(1963).The proposed methodology is capable of defining the structural anisotropy of a rock mass including joint pattern from extremely closely to extremely widely spaced joints.

Anisotropy of strength and deformability of fractured rocks

Anisotropy of the strength and deformation behaviors of fractured rock masses is a crucial issue for design and stability assessments of rock engineering structures, due mainly to the non-uniform and non- regular geometries of the fracture systems. However, no adequate efforts have been made to study this issue due to the current practical impossibility of laboratory tests with samples of large volumes con- taining many fractures, and the difficulty for controlling reliable initial and boundary conditions for large-scale in situ tests. Therefore, a reliable numerical predicting approach for evaluating anisotropy of fractured rock masses is needed. The objective of this study is to systematically investigate anisotropy of strength and deformability of fractured rocks, which has not been conducted in the past, using a nu- merical modeling method. A series of realistic two-dimensional （2D） discrete fracture network （DFN） models were established based on site investigation data, which were then loaded in different directions, using the code UDEC of discrete element method （DEM）, with changing confining pressures. Numerical results show that strength envelopes and elastic deformability parameters of tested numerical models are significantly anisotropic, and vary with changing axial loading and confining pressures. The results indicate that for design and safety assessments of rock engineering projects, the directional variations of strength and deformability of the fractured rock mass concerned must be treated properly with respect to the directions of in situ stresses. Traditional practice for simply positioning axial orientation of tunnels in association with principal stress directions only may not be adequate for safety requirements. Outstanding issues of the present study and su^zestions for future study are also oresented.

Anisotropic time-dependent behaviors of shale under direct shearing and associated empirical creep models

Understanding the anisotropic creep behaviors of shale under direct shearing is a challenging issue.In this context,we conducted shear-creep and steady-creep tests on shale with five bedding orientations (i.e.0°,30°,45°,60°,and 90°),under multiple levels of direct shearing for the first time.The results show that the anisotropic creep of shale exhibits a significant stress-dependent behavior.Under a low shear stress,the creep compliance of shale increases linearly with the logarithm of time at all bedding orientations,and the increase depends on the bedding orientation and creep time.Under high shear stress conditions,the creep compliance of shale is minimal when the bedding orientation is 0°,and the steady-creep rate of shale increases significantly with increasing bedding orientations of 30°,45°,60°,and 90°.The stress-strain values corresponding to the inception of the accelerated creep stage show an increasing and then decreasing trend with the bedding orientation.A semilogarithmic model that could reflect the stress dependence of the steady-creep rate while considering the hardening and damage process is proposed.The model minimizes the deviation of the calculated steady-state creep rate from the observed value and reveals the behavior of the bedding orientation's influence on the steady-creep rate.The applicability of the five classical empirical creep models is quantitatively evaluated.It shows that the logarithmic model can well explain the experimental creep strain and creep rate,and it can accurately predict long-term shear creep deformation.Based on an improved logarithmic model,the variations in creep parameters with shear stress and bedding orientations are discussed.With abovementioned findings,a mathematical method for constructing an anisotropic shear creep model of shale is proposed,which can characterize the nonlinear dependence of the anisotropic shear creep behavior of shale on the bedding orientation.

Research on unloading nonlinear mechanical characteristics of jointed rock masses

Geological environments of rock mass projects are always very complicated, and further investigations on rock mechanical characteristics are needed. There are considerable distinctions in rock mechanical characteristics under unloading and loading conditions. A series of tests are conducted to study the stress-strain relationship of rock masses under loading and unloading conditions. Also, the anisotropy, the size effect, and the rheological property of unloading rock mass are investigated. The tests presented in the paper include model test and granite rheological test, which are conducted considering geological condition, rock mass structure, in-situ stress field of the permanent shiplock of the Three Gorges Project. The main differences between loading and unloading rock masses are stress paths, yield criteria, deformation and strength parameters, etc.. Different structural plane directions affect unloading rock mass evidently. With increasing size, the tensile strength, the compressive strength, the deformation modulus, the Poisson’s ratio and the anisotropy of rock mass all decrease. For sandstone samples with parallel bedding planes, the cohesion c increases but the internal friction angle ? decreases under unloading condition when compared with the values under loading condition. While for samples with vertical bedding planes, the trend is adverse. The rheological property of rocks has close relationship with the tensile stresses of rock masses. When the sandstone samples are tested under high stress condition, their rheological properties are very obvious with the unloading of confining pressure, and three typical rheological stages are shown. Rheological rate changes with the variations in axial stress and confining pressure.

A modified failure criterion for transversely isotropic rocks

A modified failure criterion is proposed to determine the strength of transversely isotropic rocks. Me-chanical properties of some metamorphic and sedimentary rocks including gneiss, slate, marble, schist, shale, sandstone and limestone, which show transversely isotropic behavior, were taken into consider-ation. Afterward, introduced triaxial rock strength criterion was modified for transversely isotropic rocks. Through modification process an index was obtained that can be considered as a strength reduction parameter due to rock strength anisotropy. Comparison of the parameter with previous anisotropy in-dexes in literature showed reasonable results for the studied rock samples. The modified criterion was compared to modified Hoek-Brown and Ramamurthy criteria for different transversely isotropic rocks. It can be concluded that the modified failure criterion proposed in this study can be used for predicting the strength of transversely isotropic rocks.

Analysis of stresses at the center of transversely isotropic Brazilian disk

This article presents the stresses at the center of a Brazilian disk(BD)for transversely isotropic rocks.It is shown that the solution of stresses at the center of an anisotropic disk is a function of the disk radius and the magnitude of applied load,as well as the material orientation with respect to the load axis and two dimensionless ratios with specific physical meanings and limitations.These two dimensionless parameters are the ratios of Young’s modulus and apparent shear modulus,although the ratio of apparent shear modulus will be eliminated if the Saint-Venant assumption is considered.Considerable finite element simulations are carried out to find the stresses at the disk center concerning the material orientation and the two dimensionless parameters.Also,an approximate formula obtained from analytical results,previously proposed in the literature for solving the tensile and compressive stresses at the disk center,is re-written and simplified based on these new definitions.The results of the approximate formula fitted to the analytical results are compared to those obtained from numerical solutions,suggesting a good agreement between the numerical and analytical methods.An approximate equation for the shear stress at the disk center is also formulated based on the numerical results.Finally,the influence of the assumptions for simplification of the proposed formula for the tensile,compressive,and shear stresses at the disk center is discussed,and simple and practical equations are proposed as estimations for the stresses at the center of the BD specimen for low to moderate anisotropic rocks.For highly anisotropic rocks,the reference plots can be used for more accuracy.