Preparation of Hydroxyapatite-titanium Dioxide Coating on Ti6Al4V Substrates using Hydrothermal-electrochemical Method

Ti6Al4V substrates were anodized in a 0.5 mol/L H_2SO_4 solution at applied voltages of 90-140 V.A hydroxyapatite-titanium oxide（HA-TiO2）coating was then deposited on the anodized Ti6Al4 V substrates via a hydrothermal-electrochemicalmethod at a constant current.The obtained films and coatings were characterized by X-ray diffraction,scanning electron microscopy,energy-dispersive X-ray spectroscopy,and Fourier-transform infrared spectrometry.The microstructures of the porous films on the Ti6Al4 V substrates were studied to investigate the effect of the anodizing voltage on the phase and morphology of the HATiO_2 coating.The results indicated that both the phase composition and the morphology of the coatings were significantly influenced by changes in the anodizing voltage.HA-TiO_2 was directly precipitated onto the surface of the substrate when the applied voltage was between 110 and 140 V.The coatings had a gradient structure and the HA exhibited both needle-like and cotton-like structures.The amount of cotton-like HA structures decreased with an increase in voltage from 90 to 120 V,and then increased slightly when the voltage was higher than 120 V.The orientation index of the（002）plane of the coating was at a minimum when the Ti6Al4 V substrate was pretreated at 120 V.

Effect of rare earth Eu on anti-passivation of metal oxide anode coating

The anti passivation effect of metal oxide anode coating doped with rare earth element Eu was discussed. The morphology and the composition distribution of the metal oxide coating anode before and after electrolysis were studied by SEM and EDX analyses. The results show that the erosion of the electrolyte at the defects is the main cause for the failure of the coating. The erosion rate of the electrolyte is anisotropic. In area with high density of defects, the erosion rate is very fast and the failure of the coating is very quick. Moreover, the life time of the coating is prolonged by the doping of Eu. [

Electrochemical behavior of mesh and plate oxide coated anodes during zinc electrowinning

The catalytic performance of two oxides coated anodes （OCSs） meshes and one OCA plate was investigated in a zinc electrowinning electrolyte at 38 ℃. Their electrochemical behaviors were compared with that of a conventional Pb-0.7%Ag alloy anode. Electrochemical measurements such as cyclic voltammetric, galvanostatic, potentiodynamic, open-circuit potential （OCP） and in situ electrochemical noise measurements were considered. After 2 h of OCP test, the linear polarization shows that the corrosion current density of the Ti/（IrO2-Ta2O5） mesh electrode is the lowest （3.37μA/cm^2） among the three OCAs and shows excellent performance. Additionally, after 24 h of galvanostatic polarization at 50 mA/cm^2and 38 ℃, the Ti/MnO2mesh anode has the highest potential （1.799 V）, followed by the Ti/（IrO2-Ta2O5） plate （1.775 V） and Ti/（IrO2-Ta2O5） mesh （1.705 V） anodes. After 24 h of galvanostatic polarization followed by 16 h of decay, the linear polarization method confirms the sequence obtained after 2 h of OCP test, and the Ti/（IrO2-Ta2O5） mesh attains the lowest corrosion current density. The Ti/（IrO2-Ta2O5） mesh anode also shows better performance after 24 h of galvanostatic polarization with the overpotential lower than that of the conventional Pb-Ag anode by about 245 mV.

Improvement of stability of trivalent chromium electroplating of Ti based IrO_2+Ta_2O_5 coating anodes

The preparation process and properties of the thermally prepared Ti anodes coated with IrO2+Ta2O5 was studied. The structure and morphologies of the IrO2+Ta2O5 coatings were determined by XRD and SEM. Their electrochemical properties were studied by polarization curve and cyclic voltammetry. Trivalent chromium electroplating using Ti/IrO2+Ta2O5 anodes is carried out and the results were analyzed. Results show that this anode exhibits excellent electrochemical activity and stability in sulfate electrolysis. The electrocatalytic activity is determined not only by the content of IrO2 but also the structure and morphology of the anode coatings. The electroplating results indicats that Ti/IrO2+Ta2O5 anodes have excellent capabilities and merits in improving the stability of trivalent chromium electroplating in sulfate system.

Sub-100 nm hollow SnO_2@C nanoparticles as anode material for lithium ion batteries and significantly enhanced cycle performances

Rational designing and controlling of nanostructures is a key factor in realizing appropriate properties required for the high-performance energy fields. In the present study, hollow Sn O2@C nanoparticles（NPs） with a mean size of 50 nm have been synthesized in large-scale via a facile hydrothermal approach.The morphology and composition of as-obtained products were studied by various characterized techniques. As an anode material for lithium ion batteries（LIBs）, the as-prepared hollow Sn O2@C NPs exhibit significant improvement in cycle performances. The discharge capacity of lithium battery is as high as 370 m Ah g 1, and the current density is 3910 m A g 1（5 C） after 573 cycles. Furthermore, the capacity recovers up to 1100 m Ah g 1at the rate performances in which the current density is recovered to 156.4 m A g 1（0.2 C）. Undoubtedly, sub-100 nm Sn O2@C NPs provide significant improvement to the electrochemical performance of LIBs as superior-anode nanomaterials, and this carbon coating strategy can pave the way for developing high-performance LIBs.