RESEARCH ON MEMBRANE BIOREACTOR TREATING DOMESTIC WASTEWATER AND RELATED MECHANISMS

Experiments on treatment of domestic wastewater by membrane bioreactors were carried out.The results showed that this process could produce good quality effluent with low COD,turbidity and total count of bacteria.With intermittent operation and continuous aeration,the membrane flux was kept steady.The mechanisms of removing COD through membrane,the structure of membrane and filtration resistance were also discussed.

Effect of sludge retention time on sludge characteristics and membrane fouling of membrane bioreactor

Three identical membrane bioreactors （MBRs） were operated over 2 years at different sludge retention time （SRT） of 10 d, 40 d and no sludge withdrawal （NS）, to elucidate and quantify the effect of SRT on the sludge characteristics and membrane fouling. The hydraulic retention times of these MBRs were controlled at 12 h. With increasing SRT, the sludge concentrations in the MBRs increased, whereas the ratio of volatile suspended solid to the total solid decreased, and the size of sludge granule diminished in the meantime. A higher sludge concentration at long SRT could maintain a better organic removal efficiency, and a longer SRT was propitious to the growth of nitrifiers. The performance of these MBRs for the removal of COD and NH4^＋-N did not change much with different SRTs. However, the bioactivity decreased as SRT increase. The measurement of specific oxygen uptake rates （SOUR） and fluorescence in situ hybridization （FISH） with rRNA-targeted oligonucleotide probes testified that SOUR and the proportion of the bacteria-specific probe EUB338 in all DAPI-stainable bacteria decreased with increasing SRT. The concentrations of total organic carbon, protein, polysaccharides and soluble extracellular polymeric substance （EPS） in the mixed liquor supernatant also decreased with increasing SRT. The membrane fouling rate was higher at shorter SRT, and the highest fouling rate appeared at a SRT of 10 d. Both the sludge cake layer and gel layer had contribution to the fouling resistance, but the relative contribution of the gel layer decreased as SRT increase.

Zeolite powder addition to improve the performance of submerged gravitation-filtration membrane bioreactor

In this study, the effect of zeolite powder addition on submerged membrane bioreactor （SMBR） on membrane permeability, and the removals for COD, NH3-N, TN were investigated. Through the parallel operation of control and test systems, it was found that the zeolite powder addition could alleviate the ultra-filtration membrane fouling and enhance the membrane permeability. On the basis of experimental investigations, a concept of ＂protection coating layer＂ was proposed to illustrate the phenomenon of UF membrane fouling. In addition, the removal for COD in test system was more stable, a little higher compared to the control system. Due to the combination of nitrification and ion exchange, a more excellent removal for NH3-N in test system was obtained regardless of influent NH3-N loading rate. It was also found that a mean 25% higher TN removal took place in the test system, and ion exchange and simultaneous nitrification and de-nitrification were analyzed to be main factors. During the stable operation period, the SOURs of test zeolite powder added sludge and control activated sludge were measured to be 75 mgO2/（gMLVSS, h） and 24 mgO2/（gMLVSS, h） respectively, it meant that the zeolite powder addition could enhance the microorganism activity significantly.

Occurrence and removal of organic micropollutants in the treatment of landfill leachate by combined anaerobic-membrane bioreactor technology

Organic micropollutants,with high toxicity and environmental concern,are present in the landfill leachate at much lower levels than total organic constituents (chemical oxygen demand (COD),biochemical oxygen demand (BOD),or total organic carbon (TOC)),and few has been known for their behaviors in different treatment processes.In this study,occurrence and removal of 17 organochlorine pesticides (OCPs),16 polycyclic aromatic hydrocarbons (PAHs),and technical 4-nonylphenol (4-NP) in landfill leachate in a comb...

A pilot scale anoxic/oxic membrane bioreactor(A/O MBR) for woolen mill dyeing wastewater treatment

A pilot scale(10 m 3/d) anoxic/oxic membrane bioreactor(A/O MBR) was tested for dyeing wastewater treatment of woolen mill without wasting sludge in 125 days operation. Results showed that the effluent quality was excellent, i.e. effluent COD less than 25 mg/L, BOD 5 under 5 mg/L, turbidity lower than 0 65 NTU, and colour less than 30 DT, and met with the reuse water standard of China. The removal rates of COD, BOD 5, colour, and turbidity were 92 4%, 98 4%, 74% and 98 9%, respectively. Constant flux operation mode was carried out in this study, and backwash was effective for reducing membrane fouling and maintaining constant flux. Membrane fouling had heavy impact on energy consumption. More attention should be paid on pipe selection and design for the sidestream MBR system, too.

Effect of powdered activated carbon on Chinese traditional medicine wastewater treatment in submerged membrane bioreactor with electronic control backwashing

Chinese traditional medicine wastewater, rich in macromolecule and easy to foam in aerobic biodegradation such as Glycosides, was treated by two identical bench-scale aerobic submerged membrane bioreactors （SMBRs） operated in parallel under the same feed, equipped with the same electronic control backwashing device. One was used as the control SMBR （CSMBR） while the other was dosed with powdered activated carbon （PAC） （PAC-amended SMBR, PSMBR）. The backwashing interval was 5 min. One suction period was about 90 min by adjusting preestablished backwashing vacuum and pump frequency. The average flux of CSMBR during a steady periodic state of 24 d （576 h） was 5.87 L/h with average hydraulic residence time （HRT） of 5.97 h and that of PSMBR during a steady periodic state of 30 d （720 h） was 5.85 L/h with average HRT of 5.99 h. The average total chemical oxygen demand （COD） removal efficiency of CSMBR was 89.29% with average organic loading rate （OLR） at 4.16 kg COD/（m^3.d） while that of PSMBR was 89.79% with average OLR at 5.50 kg COD/（m^3.d）. COD concentration in the effluent of both SMBRs achieved the second level of the general wastewater effluent standard GB8978-1996 for the raw medicine material industry （300 mg/L）. Hence, SMBR with electronic control backwashing was a viable process for medium-strength Chinese traditional medicine wastewater treatment. Moreover, the increasing rates of preestablished backwashing vacuum, pump frequency, and vacuum and flux loss caused by mixed liquor in PSMBR all lagged compared to those in CSMBR; thus the actual operating time of the PSMBR system without membrane cleaning was extended by up to 1.25 times in contrast with the CSMBR system, and the average total COD removal efficiency of PSMBR was enhanced with higher average OLR.

Simultaneous nitrogen and phosphor removal in an aerobic submerged membrane bioreactor

Simultaneous nitrification and denitrification （SND） effect and phosphor removal were investigated in a one-staged aerobic submerged membrane bioreactor on pilot-scale with mixed liquor suspended solids （MLSS） 19--20 g/L. The effects of DO concentration, sludge floc size distribution on SND were studied. Test results suggested that SND was successfully performed in the membrane bioreactor （MBR） and about 70% total nitrogen removal efficiency was achieved when DO concentration was set to 0.2-- 0.3 mg/L. The main mechanisms governing SND were the suitable sludge floc size and the low DO concentration which was caused by low oxygen transfer rate with such a high MLSS concentration in the MBR. In the meantime, phosphor removal was also studied with polymer ferric sulfate （PFS） addition and 14 mg/L dosage of PFS was proper for the MBR to remove phosphor. PFS addition also benefited the MBR operation owing to its reduction of extracellular polymer substances （EPS） of mixed liquor.

Improvement of antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes （PPMMs）. Attenuated total reflection-Fourier transform infrared spectroscopy （ATR/FT-IR） and field emission scanning electron microscope （FE- SEM） were used to characterize the chemical and morphological changes on the membrane surfaces. Water contact angles and relative pure water fluxes were measured. The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes. To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor （MBR）, filtration for active sludge was performed using synthetic wastewater. With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d, the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.

Bacterial diversity in activated sludge from a consecutively aerated submerged membrane bioreactor treating domestic wastewater

The bacterial diversity of activated sludge from submerged membrane bioreactor (SMBR) was investigated. A 16S rDNA clone library was generated, and 150 clones were screened using restriction fragment length polymorphism (RFLP). Of the screened clones, almost full-length 16S rDNA sequences of 64 clones were sequenced. Phylogenetic tree was constructed with a database containing clone sequences from this study and bacterial rDNA sequences from NCBI for identification purposes. The 90.6% of the clones were a?l...

Modelling the biological performance of a side-stream membrane bioreactor using ASM1

Membrane bioreactors(MBRs) are attracting global interest but the mathematical modeling of the biological performance of MBRs remains very limited. This study focuses on the modelling of a side-stream MBR system using Activated Sludge Model No.1(ASM1), and comparing the results with the modelling of traditional activated sludge processes. ASM1 parameters relevant for the long-term biological behaviour in MBR systems were calibrated(i.e. Y H=0.72gCOD/gCOD, Y A=0.25gCOD/gN, b H=0.25 d -1, b A=0.080 d -1 and f P=0.06), and generally agreed with the parameters in traditional activated sludge processes, with the exception that a higher autotrophic biomass decay rate was observed in the MBR. A sensitivity analysis for steady state operation and DO dynamics suggested that the biological performance of the MBR system(the sludge concentration, effluent quality and the DO dynamics) are very sensitive to the parameters(i.e. Y H, Y A, b H, b A, μ maxH and μ maxA), and influent wastewater components(X I, S S, X S, S NH).

Feasibility and simulation model of a pilot scale membrane bioreactor for wastewater treatment and reuse from Chinese traditional medicine

The lack and pollution of water resource make wastewater reuse necessary. The pilot scale long-term tests for submerged membrane bioreactor were conducted to treat the effluents of anaerobic or aerobic treatment process for the high-strength Chinese traditional medicine wastewater. This article was focused on the feasibility of the wastewater treatment and reuse at shorter hydraulic retention time （HRT） of 5.0, 3.2 and 2.13 h. MLSS growth, membrane flux, vacuum values and chemical cleaning periods were also investigated. The experimental results of treating two-phase anaerobic treatment effluent demonstrated that the CODfilt was less than 100 mg/L when the influent COD was between 500-10000 mg/L at HRT of 5.0 h, which could satisfy the normal discharged standard in China. The experimental results to treat cross flow aerobic reactor effluent demonstrated that the average value of CODfilt was 17.28 mg/L when the average value of influent COD was 192.84 mg/L at HRT of 2.13 h during 106 d, which could completely meet the normal standard for water reuse. The maximum MLSS and MLVSS reached 24000 and 14500 mg/L at HRT of 3.2 h respectively. Membrane flux had maximal resume degrees of 94.7% at vacuum value of 0.02 MPa after cleaning. Chemical cleaning periods of membrane module were 150 d. A simulation model of operational parameters was also established based on the theory of back propagation neural network and linear regression of traditional mathematical model. The simulation model showed that the optimum operational parameters were suggested as follows： HRT was 5.0 h, SRT was 100 d, the range of COD loading rate was between 10.664-20.451 kg/（m3.d）, the range of MLSS was between 7543-13694 mg/L.

Membrane Separation Technology on Pharmaceutical Wastewater by Using MBR (Membrane Bioreactor)

This study demonstrated the feasibility of implementing of MBR in pharmaceutical wastewater independently, and concluded different applications of MBR in industries. Membrane bioreactor (MBR) technology was a new wastewater treatment technology with a combination of membrane separation technology and biological treatment technology, which had unique advantages on pharmaceutical wastewater treatment. The modified membrane rector design provided a significantly lower concentration of NH3-N, Phosphorous, Total Nitrogen and COD around the membranes, and subsequently a more sustainable membrane performance due to much lower overall fouling rates. In this paper, the classification and structure of biological waste water treatment by using MBR technology were summed up along with some examples of MBR in industrial wastewater treatment, which was emphatically analyzed and discussed. Finally, the prospect of MBR in industrial wastewater treatment was described. The industrial wastewater was a high-strength wastewater which had characteristics of complicated constituents, high organics concentration, highly toxic.

Determination and discussion hydraulic retention time in membrane bioreactor system

Based on the microorganism kinetic model, the formula for computing hydraulic retention time in a membrane bioreactor system (MBR) is derived. With considering HRT as an evaluation index a combinational approach was used to discuss factors which have an effect on MBR. As a result, the influencing factors were listed in order from strength to weakness as: maximum specific removal rate K , saturation constant K s, maintenance coefficient m , maximum specific growth rate μ m and observed yield coefficient Y obs . Moreover, the formula was simplified, whose parameters were experimentally determined in petrochemical wastewater treatment. The simplified formula is θ=1.1(1/β-1)(K s +S)/KX 0, for petrochemical wastewater treatment K and K s equaled 0 185 and 154.2, respectively.

Inorganic nitrogen removal of toilet wastewater with an airlift external circulation membrane bioreactor

Removal of inorganic nitrogen （inorganic-N） from toilet wastewater, using a pilot-scale airlift external circulation membrane bioreactor （AEC-MBR） was studied. The results showed that the use of AEC-MBR with limited addition of alkaline reagents and volumetric loading rates of inorganic-N of 0.19-0.40 kg inorganic-N/（m^3·d） helped achieve the desired nitrification and denitrification. Furthermore, the effects of pH and dissolved oxygen （DO） on inorganic-N removal were examined. Under the condition of MLSS at 1.56-2.35 g/L, BODs/ammonia nitrogen （NH4＋-N） at 1.0, pH at 7.0-7.5, and DO at 1.0-2.0 mg/L, the removal efficiencies of NH4^＋-N and inorganic-N were 91.5% and 70.0%, respectively, in the AEC-MBR. The cost of addition of alkaline reagent was approximately 0.5-1.5 RMB yuan/m^3, and the energy consumption was approximately 0.72 kWh/m^3 at the flux of 8 L/（m^2-h）.

Removal of Di-2-Ethyl Hexyl Phthalates by Membrane Bioreactor

A lab scale membrane bioreactor system was built to investigate the removal of Di-2-Ethyl Hexyl Phthalates (DEHP) in wastewater under variation of three runs: two hydraulic retention time (HRT) 24 and 36 hours in addition to two biomass: concentrated and light sludge. Solid phase extraction (SPE) followed by high performance liquid chromatography coupled with tandem mass spectrometry (HPLC-MS/MS) was applied to quantitatively identify DEHP in wastewater samples. Membrane bioreactor was built and operated to investigate DEHP removal. Higher HRT removed DEHP more efficiently than lower HRT. The concentrated MLSS could achieve higher removal efficiency than the lighter MLSS at the same HRT value. The performance of MBR in removing DEHP, TOC and COD from wastewater with a maximum removal efficiency were 29%, 85%, and 98%, respectively. Mass balance of DEHP in the system indicated that a majority was removed by adsorption process rather than filtration or microbiological process.

Effect of components in activated sludge liquor on membranefouling in a submerged membrane bioreactor

By a membrane bioreactor with a settle tank in long-term operation and batch experiments, the effects of floes, soluble microorganism products （SMPs） and metal ions in activated sludge liquor on membrane fouling were investigated. The results showed that foulants absorbed each other and formed a fouling layer as a ＂second membrane＂ influencing the permeability of the membrane. The ＂gel layer＂ caused by SMPs and ＂cake layer＂ by floes showed great differences in morphology by analysis of scanning electron microscope and atomic force microscope. The ＂gel layer＂ was more compact and of poor permeability. When the membrane flux was 40 L/（m^2·h）, the rate of membrane fouling caused by supernatant （0.011 MPa/h） was greater than that by sludgc liquor （0.0063 MPa/h）. SMPs played very important roles on membrane fouling. In the bulking sludge, with SMPs increasing, the rate of membrane fouling （0.0132 MPa/h） was faster. While after flocculation of the SMPs, the rate of fouling decreased to 0.0034 M Pa/h. Floes could keep holes in their overlaps. They could alleviate membrane fouling by preventing the SMPs directly attaching on membrane surface.

Membrane bioreactor process of organic wastewater from brassylic acid manufacturing plant

The wastewater treatment from brassylic acid manufacturing plant using membrane bioreactor (MBR) was studied. The membrane bioreactor consisted of batch-operation biological aeration tank and ultrafiltration evaluation tank. The content of test included the affection of variation operation conditions on ultrafiltration separation, the general characteristics of MBR process, and the difference comparing with the conventional biological treatment. The results are as follows: (1) among the test membrane material, polyether sulphone (PES) membrane is more suitable for the wastewater treatment; (2) when the cutoff molecular weight is among 10000-50000, the higher the cutoff molecular weight, the bigger the water flux is in the test; (3) under the operation pressure, water flux increases accompanying with the increasing of operation pressure; (4) the paper filtered COD concentration has more affection on the water flux than the suspended solid concentration; ( 5) as they volume loading of MBR increases, the accumulation of high molecule organic substance and colloid increases, the membrane,permeate COD concentration and paper filtered COD concentration increase too, meanwhile the water flux reduces; (6) when the sludge retention time of activated sludge of MBR increases, the accumulation of high molecule organic substance and colloid reduces, the membrane permeate (:OD concentration and paper filtered COD concentration reduce too, and the water flux increases; (7) comparing with the conventional biological process, the microbial activity is higher, but the microbial species is less.

Variation of peroxidase isoenzyme and biofilm of Phanerochaete chrysosporium in continuous membrane bioreactor for Reactive Brilliant Red X3-B treatment

The influence of a Reactive Brilliant Red X-3B （RBR X-3B） dye on the peroxidase isoenzyme ofPhanerochaete chrysosporium was determined, and the biofilm structure in a white rot fungal continuous membrane bioreactor （MBR） was also investigated by scanning electron microscope （SEM）. The variation of peroxidase isoenzyme and the decolorization rate in the continuous MBR were evaluated. The results showed that the 100 mg/L RBR X-3B could stimulate the production of the peroxidase isoenzyme in the shaking-flask culture. In addition, two new peroxidase isoenzyme bands with relative mobility （Rf） value of 0.27 and 0.28 appeared, but the activity was lower than the blank control of 11 d. In the continuous MBR, the system worked stably during the first 60 d, the main peroxidase isoenzyme bands existed and three new bands with Rf value of 0.10, 0.27, and 0.28 appeared. Meanwhile, the biofilm grew well and the average decolorization rate could reach 90.6%. But the bands of peroxidase isoenzyme decreased rapidly at day 65, only two bands with Rf value 0.24 and 0.26 existed, and the decolorization rate decreased to 78.3%. Therefore, 5 bottles of P. chrysosporium mycelial pellet were added into the MBR, and then the activity of the peroxidase isoenzyme and the decolorization rate had a slight recovery. Finally, the decolorization rate finally decreased to 75.2%. These results contribute to a comprehensive understanding of the variation of peroxidase isoenzyme and biofilm in continuous MBR by white rot fungi.

Mass Transfer, Gas Holdup, and Kinetic Models of Batch and Continuous Fermentation in a Novel Rectangular Dynamic Membrane Airlift Bioreactor

Compared with conventional cylinder airlift bioreactors(CCABs)that produce coarse bubbles,a novel rectangular dynamic membrane airlift bioreactor(RDMAB)developed in our lab produces fine bubbles to enhance the volumetric oxygen mass transfer coefficient(k_(L)a)and gas holdup,as well as improve the bioprocess in a bioreactor.In this study,we compared mass transfer,gas holdup,and batch and con-tinuous fermentation for RNA production in CCAB and RDMAB.In addition,unstructured kinetic models for microbial growth,substrate utilization,and RNA formation were established.In batch fermentation,biomass,RNA yield,and substrate utilization in the RDMAB were higher than those in the CCAB,which indicates that dynamic membrane aeration produced a high k_(L)a by fine bubbles;a higher k_(L)a is more bene-ficial to aerobic fermentation.The starting time of continuous fermentation in the RDMAB was 20 h ear-lier than that in the CCAB,which greatly improved the biological process.During continuous fermentation,maintaining the same dissolved oxygen level and a constant dilution rate,the biomass accumulation and RNA concentration in the RDMAB were 9.71% and 11.15% higher than those in the CCAB,respectively.Finally,the dilution rate of RDMAB was 16.7% higher than that of CCAB during con-tinuous fermentation while maintaining the same air aeration.In summary,RDMAB is more suitable for continuous fermentation processes.Developing new aeration and structural geometry in airlift bioreac-tors to enhance k_(L)a and gas holdup is becoming increasingly important to improve bioprocesses in a bioreactor.

Anaerobic Membrane Bioreactors (AnMBR) for Wastewater Treatment

This paper focuses on the recent research in the development of anaerobic membrane bioreactors in wastewater treatment. Anaerobic wastewater treatment technology is gaining increasing attention due to its capacity to convert wastewater BODs to usable biogas with relatively low energy consumption. The anaerobic membrane bioreactor (AnMBR), which is a combination of the anaerobic biological wastewater treatment process and membrane filtration, represents a recent development in the high-rate anaerobic bioreactors. This paper reviews applications and performances of AnMBR and the membrane filtration behaviour in AnMBRs.