A Combined Antenna Array Deployment with High Positioning Accuracy and Low Angular Measurement Error

In this paper,an antenna array composed of circular array and orthogonal linear array is proposed by using the design of long and short baseline“orthogonal linear array”and the circular array ambiguity resolution design of multi-group baseline clustering.The effectiveness of the antenna array in this paper is verified by sufficient simulation and experiment.After the system deviation correction work,it is found that in the L/S/C/X frequency bands,the ambiguity resolution probability is high,and the phase difference system error between each channel is basically the same.The angle measurement error is less than 0.5°,and the positioning error is less than 2.5 km.Notably,as the center frequency increases,calibration consistency improves,and the calibration frequency points become applicable over a wider frequency range.At a center frequency of 11.5 GHz,the calibration frequency point bandwidth extends to 1200 MHz.This combined antenna array deployment holds significant promise for a wide range of applications in contemporary wireless communication systems.

Wireless Strain Measurement Based on a Microstrip Patch Antenna

Wireless interrogation of a rectangular microstrip patch antenna for strain measurement is investigated by simulations.To analyze the antenna performance,a microstrip line-feeding patch antenna at 10 GHz is designed.A patch antenna wirelessly fed by a horn is proposed to measure the strain.The direction information of strain detected by the patch antenna is also considered.The strain can be detected both in the width and length directions.It is shown that the strain can be measured wirelessly using a standard horn antenna.This kind of wireless strain-sensing technique offers significant potential for wireless structural health monitoring(SHM),especially for high-end equipment.

Metallic spherical anechoic chamber for antenna pattern measurement

Anechoic chambers are used for indoor antenna measurements. The common method of constructing an anechoic chamber is to cover all inside walls by the electromagnetic absorbers. In this paper, a fully metallic spherical chamber structure is presented in which the propagation of the electromagnetic waves inside the chamber is controlled and they are guided to an absorber. In the proposed method, an appropriate quiet zone is obtained, and unlike ordinary anechoic chambers, the absorber usage amount is reduced greatly. The performance of the chamber is evaluated by simulation. The results show that the proposed method could provide a useful technique for the indoor antenna measurements.

Wireless contactless pressure measurement of an LC passive pressure sensor with a novel antenna for high-temperature applications

In this paper, a novel antenna is proposed for high-temperature testing, which can make the high-temperature pressure characteristics of a wireless passive ceramic pressure sensor demonstrated at up to a temperature of 600℃. The design parameters of the antenna are similar to those of the sensor, which will increase the coupling strength between the sensor and testing antenna. The antenna is fabricated in thick film integrated technology, and the properties of the alumina ceramic and silver ensure the feasibility of the antenna in high-temperature environments. The sensor, coupled with the ceramic antenna, is investigated using a high-temperature pressure testing platform. The experimental measurement results show that the pressure signal in a harsh environment can be detected by the frequency diversity of the sensor.

Particle Velocity Sensor and Its Application in Near-Field Noise Scanning Measurement

The Particle Velocity Sensor (PVS) is a kind of acoustic transducer which measures the particle velocity directly with figure-of-eight directivity. This paper proposes a near-field noise scanning technology based on the research of PVS, pressure-particle velocity (P-U) probe, and its application in noise source identification. Firstly, the principle and characteristics of PVS are presented. Secondly, a P-U probe is designed on the basis of PVS development. Finally, the noise measurement experiment for a single source is arranged and conducted. The result shows that the proposed P-U probe performs well in near-field noise source identification and localization.

Intelligent Antenna Attitude Parameters Measurement Based on Deep Learning SSD Model

Due to the consideration of safety,non-contact measurement methods are be-coming more acceptable.However,massive measurement will bring high labor-cost and low working efficiency.To address these limitations,this paper introduces a deep learning model for the antenna attitude parameter measurement,which can be divided into an an-tenna location phase and a calculation phase of the attitude parameter.In the first phase,a single shot multibox detector(SSD)is applied to automatically recognize and discover the antenna from pictures taken by drones.In the second phase,the located antennas’fea-ture lines are extracted and their attitude parameters are then calculated mathematically.Experiments show that the proposed algorithms outperform existing related works in effi-ciency and accuracy,and therefore can be effectively used in engineering applications.

Antenna Mechanical Pose Measurement Based on Structure from Motion

Antenna mechanical pose measurement has always been a crucial issue for radio frequency(RF)engineers,owning to the need for mechanical pose adjustment to satisfy the changing surroundings.Traditionally,the pose is estimated in the contact way with the help of many kinds of measuring equipment,but the measurement accuracy cannot be well assured in this way.We propose a non-contact measuring system based on Structure from Motion(SfM)in the field of photogrammetry.The accurate pose would be estimated by only taking several images of the antenna and after some easy interaction on the smartphone.Extensive experiments show that the error ranges of antenna's downtilt and heading are within 2degrees and 5 degrees respectively,with the shooting distance in 25 m.The GPS error is also under 5 meters with this shooting distance.We develop the measuring applications both in PC and android smartphones and the results can be computed within 3 minutes on both platforms.The proposed system is quite safe,convenient and efficient for engineers to use in their daily work.To the best of our knowledge,this is the first pipeline that solves the antenna pose measuring problem by the photogrammetry method on the mobile platform.

Towards Near-Field Communications for 6G:Challenges and Opportunities

Extremely large-scale multiple-input multiple-output(XL-MIMO)and terahertz(THz)communications are pivotal candidate technologies for supporting the development of 6G mobile networks.However,these techniques invalidate the common assumptions of far-field plane waves and introduce many new properties.To accurately understand the performance of these new techniques,spherical wave modeling of near-field communications needs to be applied for future research.Hence,the investigation of near-field communication holds significant importance for the advancement of 6G,which brings many new and open research challenges in contrast to conventional far-field communication.In this paper,we first formulate a general model of the near-field channel and discuss the influence of spatial nonstationary properties on the near-field channel modeling.Subsequently,we discuss the challenges encountered in the near field in terms of beam training,localization,and transmission scheme design,respectively.Finally,we point out some promising research directions for near-field communications.

Improved Measurement Method of Circularly-Polarized Antennas Based on Linear-Component Amplitudes

An improved measurement method of circularly-polarized (CP) antennas based on linear-component amplitudes is proposed in this paper. By utilizing two sets of orthogonal linear polarization (LP) amplitudes, measurement on axial ratio (AR) of CP antennas can be realized without phase information. However, the rotation sense of the co-polarization cannot be determined due to the absence of the phase information. Above problem is discussed here for the first time, and a solution is presented to determine the rotation sense of the co-polarization by using common auxiliary CP antennas. In addition, there will be some particular cases with large errors in actual measurement. Here a corresponding solution method is given. Finally, co-polarization and cross-polarization patterns can be further obtained from AR results. To verify this improved method, a self-developed CP microstrip array was measured. The measured results are in agreement with the simulated results, which prove this method is correct, effective and practical.

Capacity and Spatial Correlation Measurements of Compact MIMO Antennas

The dual-port compact multiple-input multiple-output(MIMO)dipole antennas with close spacing d of 0.5λand 0.3λare designed,and some electromagnetic band gap(EBG)structures are inserted between them to reduce mutual coupling.Those MIMO antennas with d=0.5λand 0.3λ,and with different mutual couplings are fabricated and measured,the channel capacity and correlation coefficient(CC)are analyzed and compared in a rich multipath reverberation chamber(RC),an office and a conference room.Results show that if d is reduced from 0.5λto 0.3λ,in the RCs,channel capacities of all the antennas are very close to that of the i.i.d.Rayleigh channel,although the average CCs are increased from 0.168 in the nonlossy RC to 0.269 in the lossy RC.In the office and conference rooms,compared with the RC,the average capacities of those antennas get a slight reduction,however,in most cases,the capacity of d=0.5λis larger than that of d=0.3λ,and the antennas with EBG have a larger capacity compared with the antennas without EBG,with a corresponding reduction of CC.A non-line-of-sight(NLOS)scenario of through-the-wall is also investigated.

The Measurement and Uncertainty Analysis of Antenna Factor of Microwave Antennas Based on Standard Site Method

A method of Standard Site Method (SSM) in the American National Standards Institute’s ANSI C63.5 is described in the frequency ranges from 30 MHz to 1000 MHz. And a measurement system is set up for determining antenna factors (AF) of antennas on an Open Area Test Sites (OATS). AF of antennas including log-periodic antenna and biconical antenna is measured with SSM method by Shanghai Institute of Measurement and Testing Technology (SIMT), which shows good agreement to data measured by National Institute of Metrology (NIM). In the end, it analyzes the measurement uncertainty of SIMT in the 30 MHz to 1000 MHz frequency band and does comparison to that of NIM.

Emulation of Realistic Multi-Path Propagation Channels inside an Anechoic Chamber for Antenna Diversity Measurements

As antennas are inherently included recommended in Over-The-Air (OTA) testing, it is important to also consider realistic channel models for the multiple-input multiple-output (MIMO) device performance evaluation. This paper aims to emulate realistic multi-Path propagation channels in terms of angles of arrivals (AoA) and cross-polarization ratio (XPR) with Rayleigh fading, inside an anechoic chamber, for antenna diversity measurements. In this purpose, a practical multi-probe anechoic chamber measurement system (MPAC) with 24 probe antennas (SATIMO SG24) has been used. However, the actual configuration of this system is not able to reproduce realistic channels. Therefore, a new method based on the control of the SG24 probes has been developed. At first time, this method has been validated numerically through the comparison of simulated and analytical AoA probability density distributions. At the second time, the performance of an antenna diversity system inside the SG24 has been performed in terms of the correlation coefficient and diversity gain (DG) using an antenna reference system. Simulated and measurements results have shown a good agreement.

Wearable Antenna Measurements in Vicinity of Human Body

This paper presents measurements techniques of wearable antennas and RF medical systems in vicinity of human body. The antennas radiation characteristics on human body have been measured by using a phantom. The phantom electrical characteristics represent the human body electrical characteristics. The phantom has a cylindrical shape with a 40 cm diameter and a length of 1.5 m. The phantom electrical characteristics are similar to the human body electrical characteristics. The antenna under test was placed on the phantom during the measurements of the antennas radiation characteristics. The phantom was employed to compare the electrical performance of several new wearable antennas. The phantom was also employed to measure the electrical performance of several antenna belts in vicinity of human body. The results of antenna with thinner belt are better than the results of the same antenna array with thicker belt.

Decoupling technique of patch antenna arrays with shared substrate by suppressing near-field magnetic coupling using magnetic metamaterials

In this paper,we propose the decoupling technique of patch antenna array by suppressing near-field magnetic coupling（NFMC） using magnetic metamaterials.To this end,a highly-integrated magnetic metamaterials,the substrate-integrated split-ring resonator（SI-SRR）,is firstly proposed to achieve negative permeability at the antenna operating frequency.By integrating SI-SRR in between two closely spaced antennas,magnetic fields are blocked in the shared substrate due to negative permeability of SI-SRR,reducing NFMC between the two antennas.To verify the technique,a prototype was fabricated and measured.The measured results demonstrated that the isolation can be enhanced by more than 17 dB even when the gap between the two patch antennas is only about 0.067 A.Due to high integration,this technique provides an effective alternative to high-isolation antenna array.

A Novel Millimeter-Wave Channel Measurement Platform for 6G Intelligent Railway Scenarios

This paper presented a novel millimeterwave channel measurement platform for the 6G intelligent railway.This platform used phased array antenna with 64 elements and can support instant bandwidth up to 1 GHz.Combined with improved multi-tone sounding signals,the platform can enhance dynamic measurement capability in high-speed railway scenarios.We performed calibration works about frequency flatness,frequency offset and proved platform reliability with channel emulator based closed-loop verification.We also carried out field trials in high-speed railway carriage scenarios.Based on measurement results,we extracted channel characteristic parameters of path loss,power delay profile and delay spread to further verify the field measurement performance of the platform.

Spin Supercurrent in Phenomena of Quantum Non-Locality (Quantum Correlations, Magnetic Vector Potential) and in Near-Field Antenna Effect

It is shown that such phenomena as quantum correlations (interaction of space-separated quantum entities), the action of magnetic vector potential on quantum entities in the absence of magnetic field, and near-field antenna effect (the existence of superluminally propagating electromagnetic fields) may be explained by action of spin supercurrents. In case of quantum correlations between quantum entities, spin supercurrent emerges between virtual particles pairs (virtual photons) created by those quantum entities. The explanation of magnetic vector potential and near-field antenna effect is based on contemporary principle of quantum mechanics: the physical vacuum is not an empty space but the ground state of the field consisting of quantum harmonic oscillators (QHOs) characterized by zero-point energy. Using the properties of the oscillators and spin supercurrent, it is proved that magnetic vector potential is proportional to the moment causing the orientation of spin of QHO along the direction of magnetic field. The near-field antenna effect is supposed to take place as a result of action of spin supercurrent causing secondary electromagnetic oscillations. In this way, the electromagnetic field may spread at the speed of spin supercurrent. As spin supercurrent is an inertia free process, its speed may be greater than that of light, which does not contradict postulates of special relativity that sets limits to the speed of inertial systems only.

Mapping an on-chip terahertz antenna by a scanning near-field probe and a fixed field-effect transistor

In the terahertz（THz） regime,the active region for a solid-state detector usually needs to be implemented accurately in the near-field region of an on-chip antenna.Mapping of the near-field strength could allow for rapid verification and optimization of new antenna/detector designs.Here,we report a proof-of-concept experiment in which the field mapping is realized by a scanning metallic probe and a fixed AlGaN/GaN field-effect transistor.Experiment results agree well with the electromagnetic-wave simulations.The results also suggest a field-effect THz detector combined with a probe tip could serve as a high sensitivity THz near-field sensor.

Spherical Near-Field - Far-Field Transformation for Quasi-Planar Antennas from Irregularly Spaced Data

An effective near-field - far-field (NF - FF) transformation with spherical scanning for quasi-planar antennas from irregularly spaced data is developed in this paper. Two efficient approaches for evaluating the regularly spaced spherical samples from the nonuniformly distributed ones are proposed and numerically compared. Both the approaches rely on a nonredundant sampling representation of the voltage measured by the probe, based on an oblate ellipsoidal modelling of the antenna under test. The former employs the singular value decomposition method to reconstruct the NF data at the points fixed by the nonredundant sampling representation and can be applied when the irregularly acquired samples lie on nonuniform parallels. The latter is based on an iterative technique and can be used also when such a hypothesis does not hold, but requires the existence of a biunique correspondence between the uniform and nonuniform samples, associ- ating at each uniform sampling point the nearest irregular one. Once the regularly spaced spherical samples have been recovered, the NF data needed by a probe compensated NF - FF transformation with spherical scanning are efficiently evaluated by using an optimal sampling interpolation algorithm. It is so possible to accurately compensate known posi- tioning errors in the NF - FF transformation with spherical scanning for quasi-planar antennas. Some numerical tests assessing the accuracy and the robustness of the proposed approaches are reported.

A Rigorous Analysis of Vehicle-to-Vehicle Range Performance in a Rural Channel Propagation Scenario as a Function of Antenna Type and Location via Simulation and Field Trails

Vehicle-to-Everything(V2X) communications will be an essential part of the technology in future autonomous drive decision systems.A fundamental procedure is to establish a robust communication channel between end-to-end devices.Due to the antenna placed at different positions on vehicles,the existing cellular electro-magnetic(EM) wave propagation modelling does not fit properly for V2X direct communication application.In order to figure out a feasible understanding of this problem,this paper focuses on the propagation channel analysis in a rural Vehicle-to-Vehicle(V2V) scenario for vehicular communication with antenna position experiments at different heights.By adopting the ray-tracing algorithm,a rural scenario simulation model is built up via the use of a commercial-off-the-shelf(COTS) EM modelling software package,that computes the path loss received power and delay spread for a given propagation channel.Next,a real-world vehicle measurement campaign was performed to verify the simulation results.The simulated and measured receiver power was in good agreement with each other,and the results of this study considered two antenna types located at three different relative heights between the two vehicles.This research provides constructive guidance for the V2V antenna characteristics,antenna placement and vehicle communication channel analysis.

Y因子法测量天线噪声温度的不确定性分析

介绍了Y因子法测量天线噪声温度的原理方法,分析了常温负载和低噪声放大器噪声温度的不确定性对天线噪声温度测量的影响,推导了天线噪声温度测量的绝对误差计算公式,研究了低噪声放大器噪声温度对天线噪声温度测量精度的影响,提出了改善天线噪声温度测量精度的方法。最后,给出了65 m射电望远镜天线L波段、C波段和X波段噪声温度测量结果。测量结果的误差分析表明:65 m射电望远镜天线噪声温度测量的绝对误差≤±2.48 K。