Ultra-Wideband Log Periodic Dipole Antenna (LPDA) for Wireless Communication Applications

This paper proposes a printed log-periodic dipole antenna (LPDA) for ultra wide bandwidth (UWB) applications. The antenna comprises of cascading four U shaped elements of different line lengths with balun circuit to improve the antenna impedance matching. The proposed antenna dimensions are 50 × 50 mm2 with FR4 substrate thickness 0.8 mm. Full-wave EM solver HFSS (High Frequency Structure Simulator) is used for modeling the proposed antenna. The pulse distortion is verified by the measured the proposed antenna performance with virtually steady group delay. The simulation and experimental results show that the proposed antenna exhibits good impedance matching, stable radiation patterns throughout the whole operating frequency bands, acceptable gain and stable group delay over the entire operating band. An UWB extended from 1.85 GHz to 11 GHz is obtained, and the average antenna gain is about 5.5 dBi over the operating band with peak gain around 6.5 dBi and 70% average radiation efficiency.

A Compact UHF Antenna Based on Hilbert Fractal Elements and a Serpentine Arrangement for Detecting Partial Discharg

Efforts to protect electric power systems from faults have commonly relied on the use of ultra-high frequency(UHF)antennas for detecting partial discharge(PD)as a common precursor to faults.However,the effectiveness of existing UHF antennas suffers from a number of challenges such as limited bandwidth,relatively large physical size,and low detection sensitivity.The present study addresses these issues by proposing a compact microstrip patch antenna with fixed dimensions of 100 mm×100 mm×1.6 mm.The results of computations yield an optimized antenna design consisting of 2nd-order Hilbert fractal units positioned within a four-layer serpentine arrangement with a fractal unit connection distance of 3.0 mm.Specifically,the optimized antenna design achieves a detection bandwidth for which the voltage standing wave ratio is less than 2 that is approximately 97.3%of the UHF frequency range(0.3–3 GHz).Finally,a prototype antenna is fabricated using standard printed circuit board technology,and the results of experiments demonstrate that the proposed antenna is capable of detecting PD signals at a distance of 8 m from the discharge source.

New Antenna Array Beamforming Techniques Based on Hybrid Convolution/Genetic Algorithm for 5G and Beyond Communications

Side lobe level reduction(SLL)of antenna arrays significantly enhances the signal-to-interference ratio and improves the quality of service(QOS)in recent and future wireless communication systems starting from 5G up to 7G.Furthermore,it improves the array gain and directivity,increasing the detection range and angular resolution of radar systems.This study proposes two highly efficient SLL reduction techniques.These techniques are based on the hybridization between either the single convolution or the double convolution algorithms and the genetic algorithm(GA)to develop the Conv/GA andDConv/GA,respectively.The convolution process determines the element’s excitations while the GA optimizes the element spacing.For M elements linear antenna array(LAA),the convolution of the excitation coefficients vector by itself provides a new vector of excitations of length N=(2M−1).This new vector is divided into three different sets of excitations including the odd excitations,even excitations,and middle excitations of lengths M,M−1,andM,respectively.When the same element spacing as the original LAA is used,it is noticed that the odd and even excitations provide a much lower SLL than that of the LAA but with amuch wider half-power beamwidth(HPBW).While the middle excitations give the same HPBWas the original LAA with a relatively higher SLL.Tomitigate the increased HPBWof the odd and even excitations,the element spacing is optimized using the GA.Thereby,the synthesized arrays have the same HPBW as the original LAA with a two-fold reduction in the SLL.Furthermore,for extreme SLL reduction,the DConv/GA is introduced.In this technique,the same procedure of the aforementioned Conv/GA technique is performed on the resultant even and odd excitation vectors.It provides a relatively wider HPBWthan the original LAA with about quad-fold reduction in the SLL.

Spin Supercurrent in Phenomena of Quantum Non-Locality (Quantum Correlations, Magnetic Vector Potential) and in Near-Field Antenna Effect

It is shown that such phenomena as quantum correlations (interaction of space-separated quantum entities), the action of magnetic vector potential on quantum entities in the absence of magnetic field, and near-field antenna effect (the existence of superluminally propagating electromagnetic fields) may be explained by action of spin supercurrents. In case of quantum correlations between quantum entities, spin supercurrent emerges between virtual particles pairs (virtual photons) created by those quantum entities. The explanation of magnetic vector potential and near-field antenna effect is based on contemporary principle of quantum mechanics: the physical vacuum is not an empty space but the ground state of the field consisting of quantum harmonic oscillators (QHOs) characterized by zero-point energy. Using the properties of the oscillators and spin supercurrent, it is proved that magnetic vector potential is proportional to the moment causing the orientation of spin of QHO along the direction of magnetic field. The near-field antenna effect is supposed to take place as a result of action of spin supercurrent causing secondary electromagnetic oscillations. In this way, the electromagnetic field may spread at the speed of spin supercurrent. As spin supercurrent is an inertia free process, its speed may be greater than that of light, which does not contradict postulates of special relativity that sets limits to the speed of inertial systems only.

Central Force Optimization with Gravity <0, Elitism, and Dynamic Threshold Optimization: An Antenna Application, 6-Element Yagi-Uda Arrays

This paper investigates the effect of adding three extensions to Central Force Optimization when it is used as the Global Search and Optimization method for the design and optimization of 6-elementYagi-Uda arrays. Those extensions are Negative Gravity, Elitism, and Dynamic Threshold Optimization. The basic CFO heuristic does not include any of these, but adding them substantially improves the algorithm’s performance. This paper extends the work reported in a previous paper that considered only negative gravity and which showed a significant performance improvement over a range of optimized arrays. Still better results are obtained by adding to the mix Elitism and DTO. An overall improvement in best fitness of 19.16% is achieved by doing so. While the work reported here was limited to the design/optimization of 6- element Yagis, the reasonable inference based on these data is that any antenna design/optimization problem, indeed any Global Search and Optimization problem, antenna or not, utilizing Central Force Optimization as the Global Search and Optimization engine will benefit by including all three extensions, probably substantially.

Spherical Near-Field - Far-Field Transformation for Quasi-Planar Antennas from Irregularly Spaced Data

An effective near-field - far-field (NF - FF) transformation with spherical scanning for quasi-planar antennas from irregularly spaced data is developed in this paper. Two efficient approaches for evaluating the regularly spaced spherical samples from the nonuniformly distributed ones are proposed and numerically compared. Both the approaches rely on a nonredundant sampling representation of the voltage measured by the probe, based on an oblate ellipsoidal modelling of the antenna under test. The former employs the singular value decomposition method to reconstruct the NF data at the points fixed by the nonredundant sampling representation and can be applied when the irregularly acquired samples lie on nonuniform parallels. The latter is based on an iterative technique and can be used also when such a hypothesis does not hold, but requires the existence of a biunique correspondence between the uniform and nonuniform samples, associ- ating at each uniform sampling point the nearest irregular one. Once the regularly spaced spherical samples have been recovered, the NF data needed by a probe compensated NF - FF transformation with spherical scanning are efficiently evaluated by using an optimal sampling interpolation algorithm. It is so possible to accurately compensate known posi- tioning errors in the NF - FF transformation with spherical scanning for quasi-planar antennas. Some numerical tests assessing the accuracy and the robustness of the proposed approaches are reported.

Synthesis of Antennas for Field and Polarization Control

This article presents a procedure for electromagnetic field and polarization control with antennas. The concept previously introduced by the authors for spatially distributed three-dimensional electromagnetic polarization (as time varies) is discussed and extended also to include non-ideal antennas and the control of electromagnetic field distributions (at a given instant of time). These polarizations and fields are herein referred to as “3D”, although time is also inherent to them. Even that the main objective is to introduce a mathematically/numerically consistent synthesis technique for controlling the 3D electromagnetic fields and polarizations, an effort is made to present and discuss possible applications, including but not limited to torus-knotted distributions and spatial multiplexing for transmission of information in wireless digital communication systems.

Assessment of the performance of the TOPGNSS and ANN-MB antennas for ionospheric measurements using low-cost u-blox GNSS receivers

Low-cost GNSS receivers have recently been gaining reliability as good candidates for ionospheric studies. In line with these gains are genuine concerns about improving the performance of these receivers. In this work, we present a comprehensive investigation of the performances of two antennas(the u-blox ANN-MB and the TOPGNSS TOP-106) used on a low-cost GNSS receiver known as the u-blox ZED-F9P. The two antennas were installed on two identical and co-located u-blox receivers. Data used from both receivers cover the period from January to June 2022. Results from the study indicate that the signal strengths are dominantly greater for the receiver with the TOPGNSS antenna than for the receiver with the ANN-MB antenna, implying that the TOPGNSS antenna is better than the ANN-MB antenna in terms of providing greater signal strengths. Summarily, the TOPGNSS antenna also performed better in minimizing the occurrence of cycle slips on phase TEC measurements. There are no conspicuous differences between the variances(computed as 5-min standard deviations) of phase TEC measurements for the two antennas, except for a period around May-June when the TOPGNSS gave a better performance in terms of minimizing the variances in phase TEC. Remarkably, the ANN-MB antenna gave a better performance than the TOPGNSS antenna in terms of minimizing the variances in pseudorange TEC for some satellite observations. For precise horizontal(North and East) positioning, the receiver with the TOPGNSS antenna gave better results, while the receiver with the ANN-MB antenna gave better vertical(Up) positioning. The errors for the receivers of both antennas are typically within about 5 m(the monthly mean was usually smaller than 1 m) in the horizontal direction and within about 10 m(the monthly mean was usually smaller than 4 m) in the vertical direction.

Microstrip Patch Antenna with an Inverted T-Type Notch in the Partial Ground for Breast Cancer Detections

This study designs a microstrip patch antenna with an inverted T-type notch in the partial ground to detect tumorcells inside the human breast.The size of the current antenna is small enough(18mm×21mm×1.6mm)todistribute around the breast phantom.The operating frequency has been observed from6–14GHzwith a minimumreturn loss of−61.18 dB and themaximumgain of current proposed antenna is 5.8 dBiwhich is flexiblewith respectto the size of antenna.After the distribution of eight antennas around the breast phantom,the return loss curveswere observed in the presence and absence of tumor cells inside the breast phantom,and these observations showa sharp difference between the presence and absence of tumor cells.The simulated results show that this proposedantenna is suitable for early detection of cancerous cells inside the breast.

Performance of joint dual links dynamic power control and smart antenna for TDMA/TDD cellular mobile communications

Interference cancellation is made available by using smart antenna at cellular base stations. Well distributed cumulative probability of signal to interference plus noise power ratio appears to be vital for cellular mobile multimedia communications. A scenario of dual links dynamic power control combined to a solution of smart antenna is proposed to adjust the instant transmission power in terms of the disparity from the favorite range. Simulation results show that this method is quite effective to improve the cumulative distribution probability performance. Meanwhile, accompanying low power consumption is also obtained at both base stations and mobile stations.

Multiband LTE-A/WWAN Antenna for a Tablet

In this paper, an internal multiband antenna is proposed for LTE-A/WWAN wireless applications in tablet computer. The proposed antenna is configured to have two branch radiators. These two branch radiators are a U-shaped driven monopole and a nonuniform wrapped inverted U-shaped monopole. The impedance bandwidths across dual operating bands are 89.7 MHz and 4185 MHz at the LTE-A/WWAN bands. Various techniques, such as branching and parasitic element are used to enhance the antenna’s bandwidth, the matching, and the size of the proposed antenna. The antenna is presented on an area of 50 × 15 mm2. Experimental results of this antenna show nearly omni-directional coverage and stable gain variation across the LTE-A/WWAN bands.

Design and Implementation of Step-Constant Tapered Slot Antennas for UWB Application

This paper presents the analytical design and high performance of step-constant tapered slot antenna (STSA) for ultra-wideband application. The return loss, radiation pattern, antenna gain, and level of cross polarization of this antenna are presented and analyzed. Utilizing Rogers (RO3006) substrate having a relative permittivity of 6.15, the proposed antenna provides the ultra-wideband (UWB) from 3.1 GHz to 10.6 GHz. It is observed that the return loss and gain are increased with increasing the step size. It has been observed from the simulation results incorporating CST microwave studio commercial software version 2015, the optimum return loss, directivity and gain are ?43 dB, 10.52 dBi and 10.20 dB, respectively, for 15 step size. Therefore, the newly proposed antenna will be a decent candidate for ultra-wideband application.

Impact of antenna and beam-selection-based sectored relay planning for 備 performance evaluation of 4G LTE-A tri-sectored cell

The deployment of Relay Nodes (RNs) in 4G LTE-A networks, mainly originating from the wireless backhaul link, provides an excellent network planning tool to enhance system performance. Better coordination between the base station and relays to mitigate inter-cell interference becomes an important aspect of achieving the required system performance, not only in the single-cell scenario, but also in multi-cell scenarios. In this paper, we model and analyze two basic approaches for designing a 4G LTE-A tri-sectored cellular system. The approaches are based on Antenna Selection Sectored Relaying (ASSR) and Beam Selection Sectored Relaying (BSSR). The main purpose of the proposed schemes is to enhance system performance by improving the quality of the wireless relay backhaul link. In this technique, antenna selection takes into consideration Non-Line-Of-Sight (NLOS) communication, whereas BSSR considers the case of Line-Of-Sight (LOS) communication using heuristic beam forming approach. The resource allocation problem has also been investigated for relay based cooperative LTE-A trisectored cell in the downlink. The best possible location for relay node in the sector, power allocation and MIMO channel modeling is formulated as an optimization problem with the aim of maximizing the end to end link rate and the Signal to Interference plus Noise Ratio (SINR) of 4G LTE-A systems. Power allocation/optimization has been solved by means of the duality equation of the stationary Karush-Kuhn-Tucker (KKT) cond让ion and is used to derive optimal values for the beam forming vector on both the relay as well as the access link. The performance of the proposed scheme is verified through simulations carried out using MATLAB software. The simulation results show a significant improvement in the SINR, throughput capacity, and coverage area of the 4G LTE-A cell, while guaranteeing better quality of service.

A Genetic Algorithm-Based Smart Antenna Technique for Anti-Collision of Multiple SAW ID-Tags

In the radio frequency identification (RFID) system based on surface acoustic wave (SAW) technique, some tags often locate in the field of a transceiver at the same time. These tags produce simultaneous echo signals which "collide" when they arrive back at the transceiver, which leads to difficult identification. In this paper, smart antenna technique is presented to implement anti-collision in SAW RFID system. The direction of arrivals (DOAs) are used to denote the locations of tags, and genetic algorithm (GA) is suggested to find the optimal estimates of the DOAs in complex multimodal search spaces. Once the DOAs are obtained, the array weights are formed and the signals of tags are recovered to implement decoding. The experimental results show that the GA-based smart antenna technique works well in some occasions.

Prediction of Bandwidth of Metamaterial Antenna Using Pearson Kernel-Based Techniques

The use of metamaterial enhances the performance of a specific class of antennas known as metamaterial antennas.The radiation cost and quality factor of the antenna are influenced by the size of the antenna.Metamaterial antennas allow for the circumvention of the bandwidth restriction for small antennas.Antenna parameters have recently been predicted using machine learning algorithms in existing literature.Machine learning can take the place of the manual process of experimenting to find the ideal simulated antenna parameters.The accuracy of the prediction will be primarily dependent on the model that is used.In this paper,a novel method for forecasting the bandwidth of the metamaterial antenna is proposed,based on using the Pearson Kernel as a standard kernel.Along with these new approaches,this paper suggests a unique hypersphere-based normalization to normalize the values of the dataset attributes and a dimensionality reduction method based on the Pearson kernel to reduce the dimension.A novel algorithm for optimizing the parameters of Convolutional Neural Network(CNN)based on improved Bat Algorithm-based Optimization with Pearson Mutation(BAO-PM)is also presented in this work.The prediction results of the proposed work are better when compared to the existing models in the literature.

DESIGN AND ANALYSIS OF MULTI-STEP AMPLITUDE QUANTIZATION WEIGHTED 2-D SOLID-STATE ACTIVE PHASED ARRAY ANTENNAS

An aperture design technique using multi-step amplitude quantization for two-dimensional solid-state active phased arrays to achieve low sidelobe is described. It can be applied to antennas with arbitrary complex aperture. Also, the gain drop and sidelobe degradation due to random amplitude and phase errors and element (or T/R module) failures are investigated.

Effect of antenna helicity on discharge characteristics of helicon plasma under a divergent magnetic field

The characteristics of the blue core phenomenon observed in a divergent magnetic field helicon plasma are investigated using two different helical antennas, namely right-handed and lefthanded helical antennas. The mode transition, discharge image, spatial profiles of plasma density and electron temperature are diagnosed using a Langmuir probe, a Nikon D90 camera,an intensified charge-coupled device camera and an optical emission spectrometer, respectively.The results demonstrated that the blue core phenomenon appeared in the upstream region of the discharge tube at a fixed magnetic field under both helical antennas. However, it is more likely to appear in a right-handed helical antenna, in which the plasma density and ionization rate of the helicon plasma are higher. The spatial profiles of the plasma density and electron temperature are also different in both axial and radial directions for these two kinds of helical antenna. The wavelength calculated based on the dispersion relation of the bounded whistler wave is consistent with the order of magnitude of plasma length. It is proved that the helicon plasma is part of the wave mode discharge mechanism.

Design and Analysis of a Compact Band Notch UWB Antenna for Body Area Network

This paper presents the design of a small printed ultra wideband antenna with Band Notched characteristics. Both the free space and on-body performances of this antenna were investigated through simulation. The newly designed UWB antenna is more revised small form factor sized, with the ability to avoid interference caused by WLAN (5.15 - 5.825 GHz) and WiMAX (5.25 - 5.85 GHz) systems with a band notch. The return loss response, gain, radiation pattern on free space of the antenna were investigated. After that, the on-body performances were tested on 3-layer human body model with radiation pattern, gain, return loss, and efficiency at 3.5, 5.7, 8, 10 GHz and all the results were compared with free space results. As the on-body performance was very good, the proposed antenna will be suitable to be used for multi-purpose medical applications and sports performance monitoring.

A Combined Antenna Array Deployment with High Positioning Accuracy and Low Angular Measurement Error

In this paper,an antenna array composed of circular array and orthogonal linear array is proposed by using the design of long and short baseline“orthogonal linear array”and the circular array ambiguity resolution design of multi-group baseline clustering.The effectiveness of the antenna array in this paper is verified by sufficient simulation and experiment.After the system deviation correction work,it is found that in the L/S/C/X frequency bands,the ambiguity resolution probability is high,and the phase difference system error between each channel is basically the same.The angle measurement error is less than 0.5°,and the positioning error is less than 2.5 km.Notably,as the center frequency increases,calibration consistency improves,and the calibration frequency points become applicable over a wider frequency range.At a center frequency of 11.5 GHz,the calibration frequency point bandwidth extends to 1200 MHz.This combined antenna array deployment holds significant promise for a wide range of applications in contemporary wireless communication systems.

Nelder-Mead Based Iterative Algorithm for Optimal Antenna Beam Patterns in Ad Hoc Networks

Directional antennas shape transmission patterns to provide greater coverage distance and reduced coverage angle. Use of adaptive directional antenna arrays can minimize interference while also being more energy efficient. When used in an ad-hoc network, this reduces interference among transmitting nodes and thereby increases throughput. Such “smart antennas” use digital beamforming based on signal processing algorithms to compute the appropriate weights to form effective antenna patterns. Smart antennas require the knowledge of the signal received at each antenna in the antenna array, thereby increasing the complexity of hardware and cost. Also, conventional smart antennas optimize results for each individual node, while it is preferable to have a global optimal solution. A problem that has not been addressed is how to compute individual beam patterns that maximize some measure of global network performance. Historically, the focus has been on finding node antenna patterns that give locally optimal performance. In this paper, we investigate a low hardware complexity beamforming approach aimed at improving global performance that uses average Noise-to-Signal ratio as the performance measure. Given a multi-hop route from source to destination, beam patterns are shaped to maximize average signal-to-noise ratio across all nodes on the route, which reduces bit-error rates and extends battery and network lifetime. The antenna weights are sequentially adjusted across all nodes in the route to achieve optimization across the network. By using phase-only weights, hardware costs are minimized. The performance of the algorithm using different path loss models is explored.