In order to prepare ornamental and anti-corrosive coating on aluminum alloys, preparation technology of black micro-arc ceramic coatings on Al alloys in silicate based electrolyte was studied. The influence of content...In order to prepare ornamental and anti-corrosive coating on aluminum alloys, preparation technology of black micro-arc ceramic coatings on Al alloys in silicate based electrolyte was studied. The influence of content of Na2WO4 and combination additive in solution on the performance of black ceramic coatings was studied; the anticorrosion performances of black ceramic coatings were evaluated through whole-immersion test and electrochemical method in 3.5% NaCl solution at different pH value; SEM and XRD were used to analyze the surface morphology and phase constitutes of the black ceramic coatings. Experimental results indicated that, without combination additives, with the increasing of Na2WO4 content in the electrolyte, ceramic coating became darker and thicker, but the color was not black; after adding combination additive, the coating turned to be black; the black ceramic coating was multi-hole form in surface. There was a small quantity of tungsten existing in the black ceramic coating beside α-Al2O3 phase and β-Al2O3 phase. And aluminum alloy with black ceramic coating exhibited excellent anti-corrosion property in acid, basic and neutral 3.5% NaCl solution.展开更多
The corrosion behavior of B30 Cu-Ni alloy in a sterile seawater and a SRB solution was investigated. The results show that the corrosion potential of specimen in the SRB solution is much lower than that in the sterile...The corrosion behavior of B30 Cu-Ni alloy in a sterile seawater and a SRB solution was investigated. The results show that the corrosion potential of specimen in the SRB solution is much lower than that in the sterile seawater. The polarization resistance of specimen in the SRB solution decreases quickly after a period immersion and becomes much lower than that in the sterile seawater. It is concluded that the SRB accelerates the corrosion process of B30 Cu-Ni alloy greatly. An anti-corrosion electroless Ni-P coating was produced and applied to the alloy. The results show that specimens coated with Ni-P plating exhibit favorable corrosion resistance property in SRB solution. Severe pitting corrosion appears on the uncoated specimens in the SRB solution when the coated specimens are still in good condition. The anti-corrosion mechanism of Ni-P plating was analyzed. It is concluded that coating the B30 Cu-Ni alloy with electroless Ni-P plating is an effective technique against the attack of SRB in marine environment.展开更多
In this work, graphene-modified epoxy-based anti-corrosion coatings were prepared and the influence of graphene on the anti-corrosion performance of the epoxy-based coatings was investigated with water contact angle t...In this work, graphene-modified epoxy-based anti-corrosion coatings were prepared and the influence of graphene on the anti-corrosion performance of the epoxy-based coatings was investigated with water contact angle test ,chemical solution immersion test, and electrochemical test. The water contact angle and chemical solution resistance of the epoxy-based coatings were improved with an increase in graphene content from 0 to 0.4%. These results prove that addition of graphene can significantly improve the hydrophobicity and impermeability of epoxy- based coatings. However, when the graphene content was increased to 0.5%, the performance of the epoxy-based coatings decreased because of graphene aggregation. Tafel polarization results show that graphene addition can significantly reduce the corrosion current density and corrosion potential of epoxy-based coatings, which enhance their anti-corrosion performance.展开更多
Methods for evaluating the resistance to cathodic disbondment （RCD） of anti-corrosion coatings on buried pipelines were reviewed. It is obvious that these traditional cathodic disbondment tests （CDT） have some dis...Methods for evaluating the resistance to cathodic disbondment （RCD） of anti-corrosion coatings on buried pipelines were reviewed. It is obvious that these traditional cathodic disbondment tests （CDT） have some disadvantages and the evaluated results are only simple figures and always rely on the subjective experience of the operator. A new electrochemical method for evaluating the RCD of coatings, that is, the potentiostatic evaluation method （PEM）, was developed and studied. During potentiostatic anodic polarization testing, the changes of stable polarization current of specimens before and after cathodic disbonding （CD） were measured, and the degree of cathodic disbondment of the coating was quantitatively evaluated, among which the equivalent cathodic disbonded distance AD was suggested as a parameter for evaluating the RCD. A series of testing parameters of the PEM were determined in these experiments.展开更多
The effect of cerium dioxide(CeO_2)as an additive on the structure and properties of a melting type coating has been studied by means of microhardness measurement,scanning electron microscopy and thermal analysis. The...The effect of cerium dioxide(CeO_2)as an additive on the structure and properties of a melting type coating has been studied by means of microhardness measurement,scanning electron microscopy and thermal analysis. The results show that cerium dioxide can modify the microstructure and tribological properties of the coating. Model LIC-23 composite coating which contains CeO_2 performs well as a self-lubricating coating in hydrochloric acid solution.展开更多
A novel enviromental protective water based metallic coating were prepared on the surface of AZ91D magnesium alloy. The properties and structure of the coating were investigated by adhension test, hardness test, heat ...A novel enviromental protective water based metallic coating were prepared on the surface of AZ91D magnesium alloy. The properties and structure of the coating were investigated by adhension test, hardness test, heat resisting test, neutral salt spray test and scanning electron microscopy (SEM). The results show that the coating has a stepped structure which can achieve good adhesion of first-grade, heat resistance temperature of 400℃, hardness of HV_ 0.50/30210 and anti-corrosion time of 250h in salt spray test. Meanwhile, the film forming and corrosion mechanism of the coating were also put forward based on the results of the Fourier transform infrared spectroscopy (FTIR) test and electrochemical impedance spectroscopy (EIS) test.展开更多
Fluororesin-based anti-corrosive coatings including graded FEP/PPS were prepared on carbon steel by melt powder coating, the bonding strength of all coating systems was determined by the pull-off test. It is found tha...Fluororesin-based anti-corrosive coatings including graded FEP/PPS were prepared on carbon steel by melt powder coating, the bonding strength of all coating systems was determined by the pull-off test. It is found that the poor adhesion of fluororesin coatings to metallic substrates is improved obviously by the graded coating structure of FEP/PPS, and the bonding strength reaches up to 11.8 MPa for the five-layer system. Examination by electron probe microanalysis （EPMA） verifies that the distribution of main components is graded in the five-layer system, which is responsible for the enhancement of the interfacial bonding.展开更多
An organic-inorganic hybrid sealing agent was fabricated and used in the plasma sprayed Al_(2)O_(3)-13 wt%TiO_(2)coating,and conventional silicone agent was also used for comparison.Protection performance of the coati...An organic-inorganic hybrid sealing agent was fabricated and used in the plasma sprayed Al_(2)O_(3)-13 wt%TiO_(2)coating,and conventional silicone agent was also used for comparison.Protection performance of the coatings was comprehensively evaluated based on both anti-corrosion and anti-biofouling properties.The results reveal that the sealing treatment is remarkably useful to decrease the porosity of the coating,and the porosity of the coating sealed with the hybrid agent is only 0.035%.Immersion corrosion test and Tafel polarization test reveal that the sealed coating with the hybrid agent exhibits a better corrosion resistance by compared with the coating sealed with silicone agent.The corrosion current density i_(corr) of the hybrid agent sealed coating is only 0.7×10^(-6)A·cm^(-2).Moreover,anti-biofouling tests both in the outdoor analogue hydraulic environment and in the natural marine environment prove that the mentioned novel coating presents a better combination of corrosion resistance and anti-biofouling property by compared with the other coatings,and it could be used as a protection of metal components in the marine environment.展开更多
To improve the durability of underwater rotating products,the corrosion characteristics in harsh marine environment were evaluated through various electrochemical experiments on the Al2O3-3TiO2 and CoNiCrAlY coating l...To improve the durability of underwater rotating products,the corrosion characteristics in harsh marine environment were evaluated through various electrochemical experiments on the Al2O3-3TiO2 and CoNiCrAlY coating layers by atmospheric pressure plasma spray coating process.By evaluating the corrosion resistance of these materials,their applicability to environmentally friendly power generation equipment such as blades of tidal current turbines was examined.According to the Tafel analysis for micro-areas including the coating layer,the coating/metal interlayer and the base metal,the Al2O3-3TiO2 coating layer and the CoNiCrAlY coating layer show markedly lower corrosion current density than the base metal.The corrosion current density of the CoNiCrAlY coating layer (9.75316×10-8A/cm2) is about 1.6 times more than that of the Al2O3-3TiO2 coating layer (6.13139×10-8A/cm2).展开更多
Fatigue crack growth tests were carried out on the SEN B3 precracked specimens, with dimensions in accordance with ISO 12108 requirements. The specimens were made of martensitic stainless steel, X17CrNi15-2, and some ...Fatigue crack growth tests were carried out on the SEN B3 precracked specimens, with dimensions in accordance with ISO 12108 requirements. The specimens were made of martensitic stainless steel, X17CrNi15-2, and some of them were modified by the ceramic coating deposition surface treatment. The effects of ceramic coating, on the fatigue crack growth behaviour of hollow shaft specimens, were experimentally investigated. Fatigue crack growth rates, da/dN, were characterised, using the power law relationship between da/dN (in mm/cycle) and the stress intensity factor range, ΔK (in MPa∙m0.5). The two constants of the correlation are 7.9768 × 10−9 and 2.8107 for the parent material, and those for the coated material are 2.4391 × 10−9 and 3.1990, respectively. Microstructural analyses were carried out on the tested specimens, which shows that the maximum hardness of the ceramic coating is higher than that of substrate by a factor of ~3.2. The dimple fracture dominates the final fracture mechanism for the parent material, and the combination of fatigue, ductile fracture and cleavage dominates the final fracture mechanism for the coated material, based on the SEM analyses. EDS tests’ results reveal that the parent material specimen shows higher levels of C at matrix regions along with Fe- and O-rich regions, compared with the coated material specimen.展开更多
基金This work was financially supported bythe Doctoral Foundation ofYanshan University(B41)theScience and Technology Foundation ofYanshan University(YDJJ0169).
文摘In order to prepare ornamental and anti-corrosive coating on aluminum alloys, preparation technology of black micro-arc ceramic coatings on Al alloys in silicate based electrolyte was studied. The influence of content of Na2WO4 and combination additive in solution on the performance of black ceramic coatings was studied; the anticorrosion performances of black ceramic coatings were evaluated through whole-immersion test and electrochemical method in 3.5% NaCl solution at different pH value; SEM and XRD were used to analyze the surface morphology and phase constitutes of the black ceramic coatings. Experimental results indicated that, without combination additives, with the increasing of Na2WO4 content in the electrolyte, ceramic coating became darker and thicker, but the color was not black; after adding combination additive, the coating turned to be black; the black ceramic coating was multi-hole form in surface. There was a small quantity of tungsten existing in the black ceramic coating beside α-Al2O3 phase and β-Al2O3 phase. And aluminum alloy with black ceramic coating exhibited excellent anti-corrosion property in acid, basic and neutral 3.5% NaCl solution.
基金Project (2005JS5144904.01) supported by the State Key Laboratory for Marine Corrosion and Protection, China
文摘The corrosion behavior of B30 Cu-Ni alloy in a sterile seawater and a SRB solution was investigated. The results show that the corrosion potential of specimen in the SRB solution is much lower than that in the sterile seawater. The polarization resistance of specimen in the SRB solution decreases quickly after a period immersion and becomes much lower than that in the sterile seawater. It is concluded that the SRB accelerates the corrosion process of B30 Cu-Ni alloy greatly. An anti-corrosion electroless Ni-P coating was produced and applied to the alloy. The results show that specimens coated with Ni-P plating exhibit favorable corrosion resistance property in SRB solution. Severe pitting corrosion appears on the uncoated specimens in the SRB solution when the coated specimens are still in good condition. The anti-corrosion mechanism of Ni-P plating was analyzed. It is concluded that coating the B30 Cu-Ni alloy with electroless Ni-P plating is an effective technique against the attack of SRB in marine environment.
文摘In this work, graphene-modified epoxy-based anti-corrosion coatings were prepared and the influence of graphene on the anti-corrosion performance of the epoxy-based coatings was investigated with water contact angle test ,chemical solution immersion test, and electrochemical test. The water contact angle and chemical solution resistance of the epoxy-based coatings were improved with an increase in graphene content from 0 to 0.4%. These results prove that addition of graphene can significantly improve the hydrophobicity and impermeability of epoxy- based coatings. However, when the graphene content was increased to 0.5%, the performance of the epoxy-based coatings decreased because of graphene aggregation. Tafel polarization results show that graphene addition can significantly reduce the corrosion current density and corrosion potential of epoxy-based coatings, which enhance their anti-corrosion performance.
基金This work is financially supported by the National Natural Science Foundation of China (No.2992021).
文摘Methods for evaluating the resistance to cathodic disbondment （RCD） of anti-corrosion coatings on buried pipelines were reviewed. It is obvious that these traditional cathodic disbondment tests （CDT） have some disadvantages and the evaluated results are only simple figures and always rely on the subjective experience of the operator. A new electrochemical method for evaluating the RCD of coatings, that is, the potentiostatic evaluation method （PEM）, was developed and studied. During potentiostatic anodic polarization testing, the changes of stable polarization current of specimens before and after cathodic disbonding （CD） were measured, and the degree of cathodic disbondment of the coating was quantitatively evaluated, among which the equivalent cathodic disbonded distance AD was suggested as a parameter for evaluating the RCD. A series of testing parameters of the PEM were determined in these experiments.
基金This is supported by the Youth Research Fund of Chinese Academy of Sciences
文摘The effect of cerium dioxide(CeO_2)as an additive on the structure and properties of a melting type coating has been studied by means of microhardness measurement,scanning electron microscopy and thermal analysis. The results show that cerium dioxide can modify the microstructure and tribological properties of the coating. Model LIC-23 composite coating which contains CeO_2 performs well as a self-lubricating coating in hydrochloric acid solution.
文摘A novel enviromental protective water based metallic coating were prepared on the surface of AZ91D magnesium alloy. The properties and structure of the coating were investigated by adhension test, hardness test, heat resisting test, neutral salt spray test and scanning electron microscopy (SEM). The results show that the coating has a stepped structure which can achieve good adhesion of first-grade, heat resistance temperature of 400℃, hardness of HV_ 0.50/30210 and anti-corrosion time of 250h in salt spray test. Meanwhile, the film forming and corrosion mechanism of the coating were also put forward based on the results of the Fourier transform infrared spectroscopy (FTIR) test and electrochemical impedance spectroscopy (EIS) test.
文摘Fluororesin-based anti-corrosive coatings including graded FEP/PPS were prepared on carbon steel by melt powder coating, the bonding strength of all coating systems was determined by the pull-off test. It is found that the poor adhesion of fluororesin coatings to metallic substrates is improved obviously by the graded coating structure of FEP/PPS, and the bonding strength reaches up to 11.8 MPa for the five-layer system. Examination by electron probe microanalysis （EPMA） verifies that the distribution of main components is graded in the five-layer system, which is responsible for the enhancement of the interfacial bonding.
基金the National Natural Science Foundation of China(No.51379070)the Graduate Research and Innovation Projects of Jiangsu Province(No.KYCX21_0463)。
文摘An organic-inorganic hybrid sealing agent was fabricated and used in the plasma sprayed Al_(2)O_(3)-13 wt%TiO_(2)coating,and conventional silicone agent was also used for comparison.Protection performance of the coatings was comprehensively evaluated based on both anti-corrosion and anti-biofouling properties.The results reveal that the sealing treatment is remarkably useful to decrease the porosity of the coating,and the porosity of the coating sealed with the hybrid agent is only 0.035%.Immersion corrosion test and Tafel polarization test reveal that the sealed coating with the hybrid agent exhibits a better corrosion resistance by compared with the coating sealed with silicone agent.The corrosion current density i_(corr) of the hybrid agent sealed coating is only 0.7×10^(-6)A·cm^(-2).Moreover,anti-biofouling tests both in the outdoor analogue hydraulic environment and in the natural marine environment prove that the mentioned novel coating presents a better combination of corrosion resistance and anti-biofouling property by compared with the other coatings,and it could be used as a protection of metal components in the marine environment.
基金Project supported by the Ministry of Education,Science Technology(MEST)Korea Industrial Technology Foundation(KOTEF)through the Human Resource Training Project for Regional Innovation
文摘To improve the durability of underwater rotating products,the corrosion characteristics in harsh marine environment were evaluated through various electrochemical experiments on the Al2O3-3TiO2 and CoNiCrAlY coating layers by atmospheric pressure plasma spray coating process.By evaluating the corrosion resistance of these materials,their applicability to environmentally friendly power generation equipment such as blades of tidal current turbines was examined.According to the Tafel analysis for micro-areas including the coating layer,the coating/metal interlayer and the base metal,the Al2O3-3TiO2 coating layer and the CoNiCrAlY coating layer show markedly lower corrosion current density than the base metal.The corrosion current density of the CoNiCrAlY coating layer (9.75316×10-8A/cm2) is about 1.6 times more than that of the Al2O3-3TiO2 coating layer (6.13139×10-8A/cm2).
文摘Fatigue crack growth tests were carried out on the SEN B3 precracked specimens, with dimensions in accordance with ISO 12108 requirements. The specimens were made of martensitic stainless steel, X17CrNi15-2, and some of them were modified by the ceramic coating deposition surface treatment. The effects of ceramic coating, on the fatigue crack growth behaviour of hollow shaft specimens, were experimentally investigated. Fatigue crack growth rates, da/dN, were characterised, using the power law relationship between da/dN (in mm/cycle) and the stress intensity factor range, ΔK (in MPa∙m0.5). The two constants of the correlation are 7.9768 × 10−9 and 2.8107 for the parent material, and those for the coated material are 2.4391 × 10−9 and 3.1990, respectively. Microstructural analyses were carried out on the tested specimens, which shows that the maximum hardness of the ceramic coating is higher than that of substrate by a factor of ~3.2. The dimple fracture dominates the final fracture mechanism for the parent material, and the combination of fatigue, ductile fracture and cleavage dominates the final fracture mechanism for the coated material, based on the SEM analyses. EDS tests’ results reveal that the parent material specimen shows higher levels of C at matrix regions along with Fe- and O-rich regions, compared with the coated material specimen.
