A method was proposed to improve the anti-rust property of hot rolled rebar, which uses oil–water emulsion cooling instead of water cooling after hot rolling. The experiments were carried out by two cooling methods, ...A method was proposed to improve the anti-rust property of hot rolled rebar, which uses oil–water emulsion cooling instead of water cooling after hot rolling. The experiments were carried out by two cooling methods, one cooled by water, the other cooled by oil–water emulsion. The results of wet/dry cyclic accelerated corrosion test showed that the anti-rust property of rebar cooled by oil–water emulsion was better than that by water obviously. The results of OM, SEM and EPMA analysis indicated that these two scales contained three layers: an outer Fe_3O_4 layer, an intermediate Fe O layer with island-shaped pro-eutectoid Fe_3O_4, an inner eutectoid Fe_3O_4 layer. For the water cooled rebar, all three layers of oxide scale were relatively thin. Moreover, the scale had plenty of defects such as porosity, and crack. However, for the oil–water emulsion cooled rebar, all three layers of oxide scale were relatively thick and compact, which played an important role in protecting the rebar from atmospheric rust.展开更多
To reduce the roll movement of an air spring passenger car, an active anti-roll system is developed, which is constructed with hydraulic and pneumatic units to change spring rate during cornering. For the comparing re...To reduce the roll movement of an air spring passenger car, an active anti-roll system is developed, which is constructed with hydraulic and pneumatic units to change spring rate during cornering. For the comparing research between the passive and active system, a two-track vehicle model and a co-simulation model of air spring system are built. For the simulation research on the linear movement of the actuator, a mathematical model is considered as dynamical subsystem in the co-simulation model. To active control the roll angle of vehicle body, a sliding-mode controller with optimized control parameters for the test vehicle is introduced into the model. The characteristics of sliding-mode controller is discussed and the validation of active antiroll control is proved by comparison with other control methods. The results show that the roll angle of air spring vehicle is reduced obviously with the active anti-roll actuator in comparison with that of the passive system. Compared with other control methods, sliding-mode controller has an advantage of shortest switching times, which leads to a longer lifetime of actuator and valves.展开更多
During cold rolled production of steel, each change of rolls causes a halt in production and affects the roll＇ s grinding maintenance and consumption. Consequently,rolls are very critical to the costs of steel produc...During cold rolled production of steel, each change of rolls causes a halt in production and affects the roll＇ s grinding maintenance and consumption. Consequently,rolls are very critical to the costs of steel production. Besides the rolling accidents, surface quality problems, including inhomogeneous wear and a decrease of the surface roughness of the rolls are other main reasons for outage and a change of the rolls. Therefore, safe rolls, with superior wear resistance and roughness retentivity will be a future trend in the cold rolling steel industry. In this study, the property characteristics and in-service performance of high-speed steel （HSS） cold rolling work rolls at Baosteel are discussed. The results of this study indicate that in-service performance of HSS cold work rolls has an improvement over conventional rolls. Implementation of HSS work rolls will prolong the rolling campaign and improve the rolling stability, thus, the cost of cold rolling production can be better controlled.展开更多
基金Project(51374069) supported by the National Natural Science Foundation of China
文摘A method was proposed to improve the anti-rust property of hot rolled rebar, which uses oil–water emulsion cooling instead of water cooling after hot rolling. The experiments were carried out by two cooling methods, one cooled by water, the other cooled by oil–water emulsion. The results of wet/dry cyclic accelerated corrosion test showed that the anti-rust property of rebar cooled by oil–water emulsion was better than that by water obviously. The results of OM, SEM and EPMA analysis indicated that these two scales contained three layers: an outer Fe_3O_4 layer, an intermediate Fe O layer with island-shaped pro-eutectoid Fe_3O_4, an inner eutectoid Fe_3O_4 layer. For the water cooled rebar, all three layers of oxide scale were relatively thin. Moreover, the scale had plenty of defects such as porosity, and crack. However, for the oil–water emulsion cooled rebar, all three layers of oxide scale were relatively thick and compact, which played an important role in protecting the rebar from atmospheric rust.
基金Sponsored by German Academic Exchange Service(Deutsche Akademische Austauschdienst)
文摘To reduce the roll movement of an air spring passenger car, an active anti-roll system is developed, which is constructed with hydraulic and pneumatic units to change spring rate during cornering. For the comparing research between the passive and active system, a two-track vehicle model and a co-simulation model of air spring system are built. For the simulation research on the linear movement of the actuator, a mathematical model is considered as dynamical subsystem in the co-simulation model. To active control the roll angle of vehicle body, a sliding-mode controller with optimized control parameters for the test vehicle is introduced into the model. The characteristics of sliding-mode controller is discussed and the validation of active antiroll control is proved by comparison with other control methods. The results show that the roll angle of air spring vehicle is reduced obviously with the active anti-roll actuator in comparison with that of the passive system. Compared with other control methods, sliding-mode controller has an advantage of shortest switching times, which leads to a longer lifetime of actuator and valves.
文摘During cold rolled production of steel, each change of rolls causes a halt in production and affects the roll＇ s grinding maintenance and consumption. Consequently,rolls are very critical to the costs of steel production. Besides the rolling accidents, surface quality problems, including inhomogeneous wear and a decrease of the surface roughness of the rolls are other main reasons for outage and a change of the rolls. Therefore, safe rolls, with superior wear resistance and roughness retentivity will be a future trend in the cold rolling steel industry. In this study, the property characteristics and in-service performance of high-speed steel （HSS） cold rolling work rolls at Baosteel are discussed. The results of this study indicate that in-service performance of HSS cold work rolls has an improvement over conventional rolls. Implementation of HSS work rolls will prolong the rolling campaign and improve the rolling stability, thus, the cost of cold rolling production can be better controlled.
