α-Fe_(2)O_(3)/epoxy resin composite superhydrophobic coating was prepared withα-Fe_(2)O_(3) nanoparticles and epoxy resin by spin coating method.The coating without epoxy resin has higher contact angle(CA)and lower ...α-Fe_(2)O_(3)/epoxy resin composite superhydrophobic coating was prepared withα-Fe_(2)O_(3) nanoparticles and epoxy resin by spin coating method.The coating without epoxy resin has higher contact angle(CA)and lower ice adhesion strength(IAS),but the mechanical properties are poor.Theα-Fe_(2)O_(3)/epoxy resin composite superhydrophobic coating exhibits good mechanical durability.In addition,compared with the bare aluminum substrate,the Ecorr of the composite coating is positive and the Jcorr is lower.The inhibition efficiency of the composite coating is as high as 99.98%in 3.5 wt%NaCl solution.The difference in the microstructure caused by the two preparation methods leads to the changes in mechanical properties and corrosion resistance of composite superhydrophobic coating.展开更多
The formation of ice on the leading edge of aircraft engines is a serious issue,as it can have catastrophic consequences.The Swirl Anti-Icing(SAI)system,driven by ejection,circulates hot fluid within a 360°annula...The formation of ice on the leading edge of aircraft engines is a serious issue,as it can have catastrophic consequences.The Swirl Anti-Icing(SAI)system,driven by ejection,circulates hot fluid within a 360°annular chamber to heat the engine inlet lip surface and prevent icing.This study employs a validated Computational Fluid Dynamics(CFD)approach to study the impact of key geometric parameters of this system on flow and heat transfer characteristics within the anti-icing chamber.Additionally,the entropy generation rate and exergy efficiency are analyzed to assess the energy utilization in the system.The research findings indicate that,within the considered flow range,reducing the nozzle specific areaφfrom 0.03061 to 0.01083 can enhance the ejection coefficient by over 60.7%.This enhancement increases the air circulating rate,thereby intensifying convective heat transfer within the SAI chamber.However,the reduction inφalso leads to a significant increase in the required bleed air pressure and a higher entropy generation rate,indicating lower exergy efficiency.The nozzle angleθnotably affects the distribution of hot and cold spots on the lip surface of the SAI chamber.Increasingθfrom 0°to 20°reduces the maximum temperature difference on the anti-icing chamber surface by 60 K.展开更多
BACKGROUND Syphilis is an infectious disease caused by Treponema pallidum that can invade the central nervous system,causing encephalitis.Few cases of anti-N-methyl-Daspartate receptor autoimmune encephalitis(AE)secon...BACKGROUND Syphilis is an infectious disease caused by Treponema pallidum that can invade the central nervous system,causing encephalitis.Few cases of anti-N-methyl-Daspartate receptor autoimmune encephalitis(AE)secondary to neurosyphilis have been reported.We report a neurosyphilis patient with anti-γ-aminobutyric acid-B receptor(GABABR)AE.CASE SUMMARY A young man in his 30s who presented with acute epileptic status was admitted to a local hospital.He was diagnosed with neurosyphilis,according to serum and cerebrospinal fluid(CSF)tests for syphilis.After 14 d of antiepileptic treatment and anti-Treponema pallidum therapy with penicillin,epilepsy was controlled but serious cognitive impairment,behavioral,and serious psychiatric symptoms were observed.He was then transferred to our hospital.The Mini-Mental State Examination(MMSE)crude test results showed only 2 points.Cranial magnetic resonance imaging revealed significant cerebral atrophy and multiple fluidattenuated inversion recovery high signals in the white matter surrounding both lateral ventricles,left amygdala and bilateral thalami.Anti-GABABR antibodies were discovered in CSF(1:3.2)and serum(1:100).The patient was diagnosed with neurosyphilis complicated by anti-GABABR AE,and received methylprednisolone and penicillin.Following treatment,his mental symptoms were alleviated.Cognitive impairment was significantly improved,with a MMSE of 8 points.Serum anti-GABABR antibody titer decreased to 1:32.The patient received methylprednisolone and penicillin after discharge.Three months later,the patient’s condition was stable,but the serum anti-GABABR antibody titer was 1:100.CONCLUSION This patient with neurosyphilis combined with anti-GABABR encephalitis benefited from immunotherapy.展开更多
Pavement snow and icing are worldwide problems, but effective countermeasures are just beginning to be developed in China. The two most common snow and ice removal methods are mechanical clearance and chemical melting...Pavement snow and icing are worldwide problems, but effective countermeasures are just beginning to be developed in China. The two most common snow and ice removal methods are mechanical clearance and chemical melting, and the advantages and disadvantages of each approach are discussed here, including environmental and structural damage caused by corrosive snow melting agents. New developments in chemical melting agents and mechanical equipment are discussed, and an overview of alternative thermal melting systems is presented, including the use of geothermy and non-geothermal heating systems utilizing solar energy, electricity, conductive pavement materials, and infrared/microwave applications. Strategic recommendations are made for continued enhancement of public safety in snow and ice conditions.展开更多
Aluminum is widely used in transmission lines, and the accumulation of ice on aluminum conductor may inflict serious damage such as tower collapse and power failure. In this study, super-hydrophobic surface （SHS） on...Aluminum is widely used in transmission lines, and the accumulation of ice on aluminum conductor may inflict serious damage such as tower collapse and power failure. In this study, super-hydrophobic surface （SHS） on alurninurn conductor with rnicro-nanostructure was fabricated using the preferential etching principle of crystal defects. The surface rnicrostructure and wettability were investigated by scanning electron microscope and contact angle measurement, respectively. The icing progress was observed with a self-made icing experiment platform at different environment temperature. The results showed that, due to jumping and rolling down of coalesced droplets from SHS of aluminum conductor at low temperature, the formation of icing on SHS could be delayed. Dynamic icing experiment indicated that SHS on aluminum conductor could restrain the formation of icing in certain temperature range, but could not exert influence on the accumulation of icing. This study offers new insight into understanding the anti-icing performance of actual aluminum conductor.展开更多
The title complex [Cu(tssb)2]2[(H3O)Cl]4H2O (C18H34Cl2CuN2O14S2) (tssb = tau- rine salicylaldehyde Schiff base) has been synthesized by the reaction of taurine salicylaldehyde Schiff base (tssb) and copper acetate in ...The title complex [Cu(tssb)2]2[(H3O)Cl]4H2O (C18H34Cl2CuN2O14S2) (tssb = tau- rine salicylaldehyde Schiff base) has been synthesized by the reaction of taurine salicylaldehyde Schiff base (tssb) and copper acetate in water-ethanol. Its single-crystal structure was determined by X-ray diffraction method. The crystal structure belongs to triclinic, space group P1 with a = 0.7407(1), b = 1.3329(3), c = 1.5736(3) nm, ?= 103.800(4), ?= 95.030(4), ?= 104.416(4)? Mr = 701.06, V = 1.4433(5) nm3, Z = 2, Dc = 1.613 g/cm3, = 1.153 mm-1 and F(000) = 726. The compound is an infinitely expanding three-dimensional network connected with hydrogen bonds. The Cu(Ⅱ) atom is coordinated by two nitrogen and two oxygen atoms to form a distorted planar coordination compound which adopts anti-configuration because two sulfonic acid groups are posi- tioned diagonally on a plane.展开更多
Novel hydrophilic NaYF4:Yb^3+,Tm^3+@NaGdF4:Ce^3+,Eu^3+double-jacket microtubes(DJMTs)with upconversion/downconversion dual-mode luminescence were designed and prepared through epitaxial growth of NaGdF4:Ce^3+,Eu^3+she...Novel hydrophilic NaYF4:Yb^3+,Tm^3+@NaGdF4:Ce^3+,Eu^3+double-jacket microtubes(DJMTs)with upconversion/downconversion dual-mode luminescence were designed and prepared through epitaxial growth of NaGdF4:Ce^3+,Eu^3+shell onto the NaYF4:Yb^3+,Tm^3+microtube via poly(acrylic acid)(PAA)mediated hydrothermal method.It is demonstrated that PAA ligand played an important role in guiding the direct growth of NaGdF4:Ce^3+,Eu^3+shell onto the surface of NaYF4:Yb^3+,Tm^3+parent microtubes.The growth of NaGdF4:Ce^3+,Eu^3+shell experienced a crystal phase transition fromβ-NaGdF4 andβ-NaYF4 mixture toβ-NaYF4@NaGdF4 composite crystal,and morphology evolution from mixture ofβ-NaGdF4:Ce^3+,Eu^3+nanorods andβ-NaYF4:Yb^3+,Tm^3+microtubes to NaYF4:Yb^3+,Tm^3+@NaGdF4:Ce^3+,Eu^3+DJMTs.The formation mechanism of DJMTs was the dissolution−renucleation ofβ-NaGdF4:Ce^3+,Eu^3+nanorods and the growth ofβ-NaGdF4:Ce^3+,Eu^3+shell via the classical Ostwald ripening mechanism.The as-prepared DJMTs could exhibit blue upconversion and red downconversion luminescence,which was further made into environmentally benign luminescent inks for creating highly secured and fluorescent-based anti-counterfeiting patterns via inkjet printing.展开更多
The icing of transmission lines threatens the security of power system. This paper proposes a novel anti-icing method based on reducing voltage of the transmission lines. The line voltage can be reduced by regulating ...The icing of transmission lines threatens the security of power system. This paper proposes a novel anti-icing method based on reducing voltage of the transmission lines. The line voltage can be reduced by regulating the ratio of the transformers which install the both ends of the transmission lines. The line current can be increased and the power loss of the transmission lines can also be increased, which means the heat generated by power loss increases and the icing process of the transmission lines can be restrained. When the icing may occur in the atrocious weather, the anti-icing transformers installed the both ends of transmission line are put into operation. The ratios of transformers are regulated to the appropriate value. The current of transmission line can be increased to the value that is a little greater than the critical current, which can realize the purpose of anti-icing. At the same time, the conditions of normal running in the load side are kept invariably, which can ensure the security of power system. This method can be applicable to a wide range. It's an effective measure to prevent the icing of the transmission lines.展开更多
In this work,the super-hydrophobic(SH)surface was prepared through chemical vapor deposition process by an argon atmospheric pressure plasma jet source with HMDSN(hexamethyldisilazane)as the polymerization precursor.P...In this work,the super-hydrophobic(SH)surface was prepared through chemical vapor deposition process by an argon atmospheric pressure plasma jet source with HMDSN(hexamethyldisilazane)as the polymerization precursor.Plasma synthesized organosilicon(SiOxCyHz)thin films with water contact angle over 160°and sliding angle below 5°,were able to be achieved.FTIR and XPS analysis indicates a large number of hydrocarbon compositions were polymerized in the thin films enduing the latter very-low surface free energy.SEM shows the SH films display micro-nanostructure and with high degree of averaged surface roughness 190 nm evaluated by AFM analysis.From experiments under controlled low-temperature and moisture conditions,the prepared SH surface exhibits good anti-icing effects.Significantly prolonging freezing time was achievable on the SH thin films for both static and sliding water droplets.This investigation demonstrates the anti-icing potentials of SH surface prepared through low-cost simple atmospheric-pressure plasma polymerization process.展开更多
Many flight and icing conditions should be considered in order to design an efficient ice protection system to prevent ice accretion on the aircraft surface. The anti-icing heat load is the basic knowledge for the des...Many flight and icing conditions should be considered in order to design an efficient ice protection system to prevent ice accretion on the aircraft surface. The anti-icing heat load is the basic knowledge for the design of a thermal anti-icing system. In order to help the design of the thermal anti-icing system and save the design time, a fast and efficiency method for prediction the anti-icing heat load is investigated. The computation fluid dynamics (CFD) solver and the Messinger model are applied to obtain the snapshots. Examples for the calculation of the anti-icing heat load using the proper orthogonal decomposition (POD) method are presented and compared with the CFD simulation results. It is shown that the heat loads predicted by POD method are in agreement with the CFD computation results. Moreover, it is obviously to see that the POD method is time-saving and can meet the requirement of real-time prediction.展开更多
基金Supported by the National Natural Science Foundation of China(No.51801058)the Special Program for Guiding Local Science and Technology Development by the Central Government of Hubei Province(No.2019ZYYD006)the Education and Teaching Research Project of Hubei Polytechnic University(No.2021B01)。
文摘α-Fe_(2)O_(3)/epoxy resin composite superhydrophobic coating was prepared withα-Fe_(2)O_(3) nanoparticles and epoxy resin by spin coating method.The coating without epoxy resin has higher contact angle(CA)and lower ice adhesion strength(IAS),but the mechanical properties are poor.Theα-Fe_(2)O_(3)/epoxy resin composite superhydrophobic coating exhibits good mechanical durability.In addition,compared with the bare aluminum substrate,the Ecorr of the composite coating is positive and the Jcorr is lower.The inhibition efficiency of the composite coating is as high as 99.98%in 3.5 wt%NaCl solution.The difference in the microstructure caused by the two preparation methods leads to the changes in mechanical properties and corrosion resistance of composite superhydrophobic coating.
基金Shenyang Key Laboratory of Aircraft Icing and Ice Protection,Grant Number XFX20220303Education Department of Hunan Province,China,Grant Number 23A0504National Natural Science Foundation of China,Grant Number 52275108.
文摘The formation of ice on the leading edge of aircraft engines is a serious issue,as it can have catastrophic consequences.The Swirl Anti-Icing(SAI)system,driven by ejection,circulates hot fluid within a 360°annular chamber to heat the engine inlet lip surface and prevent icing.This study employs a validated Computational Fluid Dynamics(CFD)approach to study the impact of key geometric parameters of this system on flow and heat transfer characteristics within the anti-icing chamber.Additionally,the entropy generation rate and exergy efficiency are analyzed to assess the energy utilization in the system.The research findings indicate that,within the considered flow range,reducing the nozzle specific areaφfrom 0.03061 to 0.01083 can enhance the ejection coefficient by over 60.7%.This enhancement increases the air circulating rate,thereby intensifying convective heat transfer within the SAI chamber.However,the reduction inφalso leads to a significant increase in the required bleed air pressure and a higher entropy generation rate,indicating lower exergy efficiency.The nozzle angleθnotably affects the distribution of hot and cold spots on the lip surface of the SAI chamber.Increasingθfrom 0°to 20°reduces the maximum temperature difference on the anti-icing chamber surface by 60 K.
文摘BACKGROUND Syphilis is an infectious disease caused by Treponema pallidum that can invade the central nervous system,causing encephalitis.Few cases of anti-N-methyl-Daspartate receptor autoimmune encephalitis(AE)secondary to neurosyphilis have been reported.We report a neurosyphilis patient with anti-γ-aminobutyric acid-B receptor(GABABR)AE.CASE SUMMARY A young man in his 30s who presented with acute epileptic status was admitted to a local hospital.He was diagnosed with neurosyphilis,according to serum and cerebrospinal fluid(CSF)tests for syphilis.After 14 d of antiepileptic treatment and anti-Treponema pallidum therapy with penicillin,epilepsy was controlled but serious cognitive impairment,behavioral,and serious psychiatric symptoms were observed.He was then transferred to our hospital.The Mini-Mental State Examination(MMSE)crude test results showed only 2 points.Cranial magnetic resonance imaging revealed significant cerebral atrophy and multiple fluidattenuated inversion recovery high signals in the white matter surrounding both lateral ventricles,left amygdala and bilateral thalami.Anti-GABABR antibodies were discovered in CSF(1:3.2)and serum(1:100).The patient was diagnosed with neurosyphilis complicated by anti-GABABR AE,and received methylprednisolone and penicillin.Following treatment,his mental symptoms were alleviated.Cognitive impairment was significantly improved,with a MMSE of 8 points.Serum anti-GABABR antibody titer decreased to 1:32.The patient received methylprednisolone and penicillin after discharge.Three months later,the patient’s condition was stable,but the serum anti-GABABR antibody titer was 1:100.CONCLUSION This patient with neurosyphilis combined with anti-GABABR encephalitis benefited from immunotherapy.
基金supported by the National Natural Science Fund of China(No.41121061)the National Key Basic Research and Development Program(No.2012CB026102)the Fund of the "Hundred People Plan" of CAS(to WenBing Yu)
文摘Pavement snow and icing are worldwide problems, but effective countermeasures are just beginning to be developed in China. The two most common snow and ice removal methods are mechanical clearance and chemical melting, and the advantages and disadvantages of each approach are discussed here, including environmental and structural damage caused by corrosive snow melting agents. New developments in chemical melting agents and mechanical equipment are discussed, and an overview of alternative thermal melting systems is presented, including the use of geothermy and non-geothermal heating systems utilizing solar energy, electricity, conductive pavement materials, and infrared/microwave applications. Strategic recommendations are made for continued enhancement of public safety in snow and ice conditions.
基金supported by the National Natural Science Foundation of China (No.51272208)
文摘Aluminum is widely used in transmission lines, and the accumulation of ice on aluminum conductor may inflict serious damage such as tower collapse and power failure. In this study, super-hydrophobic surface （SHS） on alurninurn conductor with rnicro-nanostructure was fabricated using the preferential etching principle of crystal defects. The surface rnicrostructure and wettability were investigated by scanning electron microscope and contact angle measurement, respectively. The icing progress was observed with a self-made icing experiment platform at different environment temperature. The results showed that, due to jumping and rolling down of coalesced droplets from SHS of aluminum conductor at low temperature, the formation of icing on SHS could be delayed. Dynamic icing experiment indicated that SHS on aluminum conductor could restrain the formation of icing in certain temperature range, but could not exert influence on the accumulation of icing. This study offers new insight into understanding the anti-icing performance of actual aluminum conductor.
基金Supported by the NSF of Guangxi Province (No. 0339034) and the Science Research Foundation of Guangxi Universities
文摘The title complex [Cu(tssb)2]2[(H3O)Cl]4H2O (C18H34Cl2CuN2O14S2) (tssb = tau- rine salicylaldehyde Schiff base) has been synthesized by the reaction of taurine salicylaldehyde Schiff base (tssb) and copper acetate in water-ethanol. Its single-crystal structure was determined by X-ray diffraction method. The crystal structure belongs to triclinic, space group P1 with a = 0.7407(1), b = 1.3329(3), c = 1.5736(3) nm, ?= 103.800(4), ?= 95.030(4), ?= 104.416(4)? Mr = 701.06, V = 1.4433(5) nm3, Z = 2, Dc = 1.613 g/cm3, = 1.153 mm-1 and F(000) = 726. The compound is an infinitely expanding three-dimensional network connected with hydrogen bonds. The Cu(Ⅱ) atom is coordinated by two nitrogen and two oxygen atoms to form a distorted planar coordination compound which adopts anti-configuration because two sulfonic acid groups are posi- tioned diagonally on a plane.
基金Project(51874129)supported by the National Natural Science Foundation of ChinaProjects(2018JJ3115,2019JJ60049)supported by the Science Foundation of Hunan Province,ChinaProjects(19B153,19B158)supported by the Scientific Research Fund of Hunan Provincial Education Department,China。
文摘Novel hydrophilic NaYF4:Yb^3+,Tm^3+@NaGdF4:Ce^3+,Eu^3+double-jacket microtubes(DJMTs)with upconversion/downconversion dual-mode luminescence were designed and prepared through epitaxial growth of NaGdF4:Ce^3+,Eu^3+shell onto the NaYF4:Yb^3+,Tm^3+microtube via poly(acrylic acid)(PAA)mediated hydrothermal method.It is demonstrated that PAA ligand played an important role in guiding the direct growth of NaGdF4:Ce^3+,Eu^3+shell onto the surface of NaYF4:Yb^3+,Tm^3+parent microtubes.The growth of NaGdF4:Ce^3+,Eu^3+shell experienced a crystal phase transition fromβ-NaGdF4 andβ-NaYF4 mixture toβ-NaYF4@NaGdF4 composite crystal,and morphology evolution from mixture ofβ-NaGdF4:Ce^3+,Eu^3+nanorods andβ-NaYF4:Yb^3+,Tm^3+microtubes to NaYF4:Yb^3+,Tm^3+@NaGdF4:Ce^3+,Eu^3+DJMTs.The formation mechanism of DJMTs was the dissolution−renucleation ofβ-NaGdF4:Ce^3+,Eu^3+nanorods and the growth ofβ-NaGdF4:Ce^3+,Eu^3+shell via the classical Ostwald ripening mechanism.The as-prepared DJMTs could exhibit blue upconversion and red downconversion luminescence,which was further made into environmentally benign luminescent inks for creating highly secured and fluorescent-based anti-counterfeiting patterns via inkjet printing.
文摘The icing of transmission lines threatens the security of power system. This paper proposes a novel anti-icing method based on reducing voltage of the transmission lines. The line voltage can be reduced by regulating the ratio of the transformers which install the both ends of the transmission lines. The line current can be increased and the power loss of the transmission lines can also be increased, which means the heat generated by power loss increases and the icing process of the transmission lines can be restrained. When the icing may occur in the atrocious weather, the anti-icing transformers installed the both ends of transmission line are put into operation. The ratios of transformers are regulated to the appropriate value. The current of transmission line can be increased to the value that is a little greater than the critical current, which can realize the purpose of anti-icing. At the same time, the conditions of normal running in the load side are kept invariably, which can ensure the security of power system. This method can be applicable to a wide range. It's an effective measure to prevent the icing of the transmission lines.
基金partly supported by the State Key Laboratory of Advanced Electromagnetic Engineering and Technology(No.AEET 2018KF003)National Natural Science Foundation of China(Nos.51637002,11405144)+3 种基金the Fundamental Research Funds for the Central Universities(Nos.2018CDXYTW0031,20720150022)the Construction Committee of Chongqing(No.2018-1-3-6)the International Science&Technology Cooperation Program of China(No.2015DFR70390)the Natural Science Foundation of Hunan Province(No.2018JJ3587)
文摘In this work,the super-hydrophobic(SH)surface was prepared through chemical vapor deposition process by an argon atmospheric pressure plasma jet source with HMDSN(hexamethyldisilazane)as the polymerization precursor.Plasma synthesized organosilicon(SiOxCyHz)thin films with water contact angle over 160°and sliding angle below 5°,were able to be achieved.FTIR and XPS analysis indicates a large number of hydrocarbon compositions were polymerized in the thin films enduing the latter very-low surface free energy.SEM shows the SH films display micro-nanostructure and with high degree of averaged surface roughness 190 nm evaluated by AFM analysis.From experiments under controlled low-temperature and moisture conditions,the prepared SH surface exhibits good anti-icing effects.Significantly prolonging freezing time was achievable on the SH thin films for both static and sliding water droplets.This investigation demonstrates the anti-icing potentials of SH surface prepared through low-cost simple atmospheric-pressure plasma polymerization process.
文摘Many flight and icing conditions should be considered in order to design an efficient ice protection system to prevent ice accretion on the aircraft surface. The anti-icing heat load is the basic knowledge for the design of a thermal anti-icing system. In order to help the design of the thermal anti-icing system and save the design time, a fast and efficiency method for prediction the anti-icing heat load is investigated. The computation fluid dynamics (CFD) solver and the Messinger model are applied to obtain the snapshots. Examples for the calculation of the anti-icing heat load using the proper orthogonal decomposition (POD) method are presented and compared with the CFD simulation results. It is shown that the heat loads predicted by POD method are in agreement with the CFD computation results. Moreover, it is obviously to see that the POD method is time-saving and can meet the requirement of real-time prediction.
