Application of Anti-seepage Technology in the Construction of Hydraulic Engineering Projects

With the development of China's economy,the implementation scale and scope of hydraulic engineering projects are increasing,and the application of anti-seepage technology has an important influence on the construction quality of hydraulic engineering.In this paper,the significance and problems of the application of anti-seepage technology in the construction of hydraulic engineering projects were mainly analyzed,and specific application strategies were proposed.

Analysis of the Properties and Anti-Seepage Mechanism of PBFC Slurry in Landfill

As the landfill leachate has strong pollution on the underground water,surface water and soil.This paper develops the formula of impervious slurry with low permeability,good durability,strong adsorption and retardant based on the bentonite which is modified by polyvinyl alcohol.Through the simulation experiment,the optimum formula of polyvinyl alcohol is 0.2%.Its osmotic coefficient for 28 days is 0.53×10^-8~1.86×10^-8 cm/s and compressive strength is 0.5~1.5 MPa as well.This paper study on the retardant rule of the consolidation of slurry against the pollution in the leachate by self-made percolation instrument.The experiment shows that the retardant rate of the consolidation against inorganic pollutants and organic pollutants is over 85% and the retardant rate against heavy metal ion such as Hg and Pb is above 99%.The slurry has the characteristics of low permeability,high retardant against pollution,good durability and plasticity,no chemical additives,no pollution,wide source of raw materials and good economy which determine it can be used to new landfill or existing landfill,building foundation pit and water conservancy project.

Discussion on Anti-seepage Wall and Anti-seepage Technology of Water Conservancy Project

The water infiltration problem of water conservancy projects is one of the more common problems in the construction of water conservancy projects,which seriously affects the overall construction quality and safety of water conservancy projects.This article studies the causes of water infiltration in water conservancy projects and introduces related antiseepage technologies,hoping to be a reference for the implementation of anti-seepage projects.Through research,it is found that the factors that cause water infiltration in water conservancy projects include water conservancy project structural changes,environmental factors and construction factors.Relevant personnel can use concrete anti-seepage wall construction technology and high-pressure jet grouting technology to do the relevant anti-seepage work of water conservancy projects.

Discussion on Anti-Seepage Technologies in the Construction of Small-Scale Rural Water Conservancy Projects

In order to ensure the sustainable growth of rural economy,it is necessary to carry out further research on small-scale water conservancy projects and solve the seepage issue in rural areas.Based on the application significance of small-scale rural water conservancy projects and the analysis of anti-seepage technologies,along with specific examples,this paper specifically discusses the application of high-pressure jet technology,so as to provide reference for the development of engineering construction.

A Review of Innovative Design Strategies for Prefabricated Green Buildings

Prefabricated green buildings are becoming a trend in the construction industry of China.The prefabricated components are made using modern technologies like green materials,artificial intelligence,and low-carbon and energy-saving techniques.This makes them an important aspect of the development of the construction industry in China,representing modernization and sustainable development.This article presents a study on the innovative design of prefabricated green buildings.This article serves to promote sustainable development on a macro level.

Anti-cracking Property of EVA-modified Polypropylene Fiber-reinforced Concrete Under Thermal-cooling Cycling Curing

In order to investigate the synergistic effect of re-dispersible powder-ethylene-vinyl acetate copolymer(EVA) and polypropylene fiber on the crack resistance of concrete under thermal fatigue loading, the compressive strength, ultimate tensile strength, ultimate tensile strain and tensile modulus of elasticity were tested. In addition, ultrasonic method and scanning electron microscope analysis were used to explain the microstructure mechanism. The results show that polypropylene fiberreinforced concrete presents a better performance on crack resistance than ordinary concrete, and the synergism of EVA and polypropylene fiber can improve the anti-cracking ability of concrete further.

Influence of polymer on shrinkage and anti-cracking performance of mortar

A self-designed restrained ring test was applied to investigate cracking of mortar.The cracking total weigh W and cracking control rate K were applied to evaluate anti-cracking performance of mortar.Through the above method,the influence of polymer on the shrinkage and anti-cracking performance was studied.The microstructures of mortar specimens were investigated by means of SEM.The results indicated that the addition of polymer can efficiently reduce the shrinkage of mortar and improve the anti-cracking performance of mortar.

Effects of Filler-Asphalt Ratio on the Properties of Lignin and Polyester Fiber Reinforced SMPU/SBS Modified Asphalt Mortar

To understand the effects offiller-asphalt ratio on different properties of lignin and polyesterfiber reinforced shape memory polyurethane(SMPU)/styrene butadiene styrene(SBS)composite modified asphalt mortar(PSAM),as well as to reveal the reinforcing and toughening mechanisms of lignin and polyesterfibers on PSAM,SMPU,SBS and mineral powder werefirst utilized to prepare PSAM.Then the conventional,rheological and anti-cracking properties of ligninfiber reinforced PSAM(LFAM)and polyesterfiber reinforced PSAM(PFAM)at dif-ferentfiller-asphalt ratios were characterized.Test results indicate that the shear strength,deformation resistance and viscosity are increased after adding 0.8wt%ligninfiber or polyesterfiber and increasing thefiller-asphalt ratio from 0.8 to 1.2.The optimalfiller-asphalt ratio of 1.0 is proposed after comprehensive performance assessments of PSAM.Polyesterfiber shows a better reinforcing effect than ligninfiber,but its improvement in the thermal stability of PSAM is not significant at high temperatures.Additionally,the complex modulus,storage modulus,loss modulus and rutting resistance factor of PSAM are improved after adding ligninfiber and polyesterfiber,as well as show an increasing trend as thefiller-asphalt ratio is raised,but the phase angle is gradually decreased.Further,the increase of elastic components in PSAM effectively enhances the anti-deformation ability of PSAM at high temperatures,and polyesterfiber more obviously improves the high-temperature deformation resistance of PSAM than ligninfiber.Finally,the anti-cracking performance of PFAM and LFAM at low temperatures is reduced by 74.2%and 46.7%,respectively,as thefiller-asphalt ratio is raised from 0.8 to 1.2.The low-temperature anti-cracking performance of LFAM is lower than that of PFAM at the samefiller-asphalt ratio,even lower than that of PSA.Compared with ligninfiber,the anti-cracking performance and deformation resistance of PSAM at low temperature is more greatly enhanced by polyester fiber.

Influence of MB-value of Manufactured Sand on the Shrinkage and Cracking of High Strength Concrete

The relation between methylene blue （MB） value of MS and its limestone dust content and clay content was investigated. The effects of MB value ranging from 0.35 to 2.5 on the workability of fresh concrete and crack propagation characteristics at the age of 24 hours, and effects on the mechanical properties, dry shrinkage of the harden concrete were tested. The experimental results show that the MB value is not related with the limestone dust content of MS, but in direct proportion to clay content. With the increase of MB value, the concrete workability decreases, and the flexural strength and 7 d compressive strength reduce markedly, whearas the 28 d compressive strength is not affected. When the MB-value is less than or equal to 1.35, the change of the MB-value has a little influence on early plastic cracking and dry shrinkage property of concrete, but when the MB-value is more than 1.35, the tendency of plastic cracking and dry shrinkage is remarkable.

Optimal Percentage of Reclaimed Asphalt Pavement in Central Plant Hot Recycling Mixture

For determining the optimal percentage of RAP material in central plant hot recycling, binder was recovered from RAP by means of Abson recovery method, and properties tests of mixed binders consisting of recovered asphalt and fresh asphalt at different ratios were performed. In addition, the performances of mixture with different percentages of RAP such as rutting resistance, anti-cracking, moisture susceptibility and fatigue resistance were tested. The binder test results showed that the high temperature performance was improved with the increase of the percentage of the RAP, while the low temperature performance was declined. When the percentage of the recovered binder was less than 30%, the mixed binder could match the technical standards for fresh asphalt. Tests on the mixtures showed that rutting resistance increased gradually as RAP percentage increased, while thermal anti-cracking at low temperature and fatigue properties declined. The effect of the percentage of RAP on moisture susceptibility was limited. It is indicated that low temperature performance and fatigue properties are important for selecting the optimal percentage of RAP. Based on data obtained from binders and mixtures, it is concluded that the maximum percentage of RAP is approximately 30% without the addition of rejuvenating agent.

Retention of clay-solidified grouting curtain to Cd^(2+), Pb^(2+) and Hg^(2+) in landfill of municipal solid waste

The effects of components and their ratio of grouts on anti-seepage capability of clay-solidified grouting curtain and its permeability of heavy metal cations were investigated by permeating experiments, using reactive solute transport model to study the permeation of heavy metals (Cd2+, Pb2+ and Hg2+). The study of permeating for different mixture ratios of cement and clay indicates that hydraulic conductivity of clay-solidified grouting curtain with different ratios of solid to liquid or with the same ratio of solid to liquid but with different ratios of cement to clay is changed. The laboratory simulation test results also show that precipitates produced in heavy metal cation migration process in curtain block up water flowing passage which makes the hydraulic conductivity of the solution-permeated curtain decrease with the leakage time. The permeation velocities for different heavy metal cations vary with ionic concentration, exchange capacity and ion radius etc. The test results indicate that the permeation rapidity order of heavy metals cations in clay-solidified grouting curtain is Hg2+>Pb2+ in the same experimental circumstance. In addition, permeability for different mixture ratios and antisepsis capabilities of clay-solidified grouting curtain were studied in tests.

The Properties of Road Base Course Materials of Granular Soils Stabilized by AGS Granular Soil Stabilizing Cement

The properties of road base course materials of granular soils stabilized by AGS granular soil stabilizing cement were studied.The AGS cement has an expansibility to a certain degree,so the dry shrinkage of AGS cement paste and AGS stabilized granular is much lower than that of Portland slag cement.AGS has a good suitability to granular soils.Granular soils stabilized by AGS have a much higher strength than that of soils stabilized by P S cement.The same strength can be reached with 20% reduction of cement dosage for AGS cement.And their elastic and resilient modulus are similar,but the former has a much higher tensile splitting strength,so the AGS stabilized granular has a much better anti-cracking performance than that of the P S stabilized granular.The reduced value of the strength and the density with the retard time for the granular soils stabilized by AGS is lower than that for P S cement.

Anti-Crack Performance of Phosphorus Slag Concrete

Anti-crack performance of concrete with phosphorus slag and fly ash singly and compositely added is investigated in terms of physical performance, hydration heat, dry shrinkage and creep. Index K is introduced to evaluate the crack resistance of phosphorus slag concrete. Results show that the strength of phosphorus slag concrete increases with the increase of fineness, and when surface specific area is greater than 300 m^2/kg, the tendency slows down. Strength decreases with phosphorus slag content increasing and there is an optimal content existing between 30% and 50%. Both phosphorus slag and fly ash have obvious effect on elongating time setting, reducing hydration heat to a large extent and increasing creep value. Crack resistance of phosphorus slag concrete is divided into three stages, namely early hazardous stage, growth stage and later mature stage. With microstructure analysis, mechanism of effect of phosphorus slag on concrete performances and P and F on cement hydration is explored. It is concluded after comprehensive evaluation that the crack resistance of phosphorus slag concrete is approximate to, even to some extent better than that of fly ash concrete.