Design Concept for an Anchored Diaphragm Wall in the Central Part of Budva, Montenegro

This paper presents a design concept and acceptance test application procedure for a deep pit protection structure. The structure is intended for use in the construction of three underground levels of a residential building： A, B, C and D, located in Block 10C, Budva, Montenegro. The anchored wall will consist of non-gravity cantilevered walls with three levels of ground anchors. Non-gravity cantilevered walls employ continuous walls constructed in slurry trenches （i.e., slurry （diaphragm） walls）, e.g., vertical elements that are drilled to depths below the finished excavation grade. For those non-gravity cantilevered walls, support is provided through the shear and bending stiffness of the vertical wall elements and passive resistance from the soil below the finished excavation grade. Anchored wall support relies on these components as well as lateral resistance provided by the ground anchors to resist horizontal pressures （e.g., earth, water and external loads） acting on the wall. The anchored wall analyzed in this paper will be recommended for use as a temporary supporting structure necessary for the excavation and erection of the underground structure. The design life of the temporary ground anchors is two years. Dynamic loads are not considered in this analysis.

Dynamic response of a slope reinforced by double-row antisliding piles and pre-stressed anchor cables

Large-scale shaking table tests were conducted to study the dynamic response of a slope reinforced by double-row anti-sliding piles and prestressed anchor cables. The test results show that the reinforcement suppressed the acceleration amplification effectively. The axial force time histories are decomposed into a baseline part and a vibration part in this study. The baseline part of axial force well revealed the seismic slope stability, the peak vibration values of axial force of the anchor cables changed significantly in different area of the slope under seismic excitations. The peak lateral earth pressure acting on the back of the anti-sliding pile located at the slope toe was much larger than that acting on the back of the anti-sliding pile located at the slope waist. The test results indicate an obvious load sharing ratio difference between these two anti-slide piles, the load sharing ratio between the two anti-sliding piles located at the slope toe and the slope waist varied mainly in a range of 2-5. The anti-slide pile at the slope waist suppressed the horizontal displacement of the slope surface.

Free-Fall Penetration Behaviors of A New Dynamically Installed Plate Anchor in Marine Clay

A new dynamically installed plate anchor, the Flying Wing Anchor~?, has been developed as a sustainable anchor concept for deep-water offshore wind turbines. The anchor is firstly installed by free-fall penetration and then followed by drag embedment. If the anchor is subjected to environmental loads, it dives deeper to mobilize a higher capacity. This study presents a series of free-fall penetration tests with model anchors in different weights to assess the anchor behavior during the free-fall penetration performance in one-layer soil with a constant shear strength profile. Anchor velocities and embedment depths were measured by a magnetometer. An energy-based model and a force-based model were calibrated against the test results of model anchors with different weights. Based on the calibrated force-based model, a series of design charts were developed to estimate the embedment depth of anchors in different sizes and with different impact velocities in various marine clays. The framework to plot design charts presented herein can be potentially applied to other dynamically installed anchors to predict embedment depth in engineering practice.

A new anchor-siphon drainage combined method used for slope stabilization

A new anchor-siphon drainage combined method used for slope stabilization is proposed in this paper.It includes an anchoring section and a siphon drainage section.The novelty of the anchor-siphon drainage combined method is the realization of the drainage and anchoring in the one inclined borehole.The engineering cost of drilling and the resulting disturbance to the slope is reduced.To validate the feasibility of the proposed method,a numerical method that combines the pore water pressure distribution after siphon drainage and the anchoring force of the anchoring section is used to evaluate the safety of the slope with the anchor-siphon drainage method.The proposed method was illustrated and validated with the Hongpu Village landslide,in Tonglu County,Zhejiang Province,in China.Compared with the common anchor bar with the same length in the anchoring section,the factor of safety(FOS)for Hongpu Village slope with anchorsiphon drainage is increased by 0.085.The calculation method of the optimal length ratio between the drainage section and the anchoring section and its influencing factors were studied.For the different design parameters,there is always an optimal length ratio of the drainage section.Compared with the siphon drainage and full-length anchor bar with the same borehole length,the anchor-siphon drainage combined method shows better landslide prevention ability.Moreover,when the optimized parameters with a bond strength of 560kPa,a borehole inclination of 35°,and no reduction in length are used,the calculated safety factor is 1.316,which is significantly higher than the FOS of 1.131 for the slope with siphon drainage.

Analysis on the anchor mechanism of the full length resin bolt

The purpose of this paper is to reveal the stress distribution characteristic along the full length anchor bolt. Based on the mechanic model set up, the author calculated the anchor mechanism of the full length resin rock bolt. The stress distribution characteristic is different according to different type of surrounding rock. The conclusion is important to optimize the roadway bolt support design.

考虑锚杆预应力作用下隧道围岩力学分析及参数设计

隧道工程中锚杆设计多依靠经验法和类比法,为研究预应力锚杆支护体系下围岩的力学效应,建立预应力锚杆与围岩力学耦合模型,考虑围岩开挖损伤效应,通过弹塑性力学理论推导出隧道开挖后围岩应力分布及径向位移解析表达式,采用有限差分软件FLAC3D进行算例验证并分析预应力锚杆参数对围岩状态的影响。研究结果表明:理论解析和数值模拟中最大切向应力和围岩塑性区半径分别为4.77 MPa、15 m和4.49 MPa、15.86 m,理论解析与数值模拟所计算隧道围岩应力分布、位移基本一致,在Ⅳ、Ⅴ级围岩地层中验证了理论解析解的合理性;随着预紧力增大,处于塑性区的围岩径向位移及塑性区半径逐渐减小,弹性区基本不受影响;当锚杆自由段长度位于塑性区时,随着锚杆长度增加,围岩塑性区径向位移及塑性区半径逐渐减小。在实际工程中应尽量增大锚杆预紧力,锚杆长度增加对围岩位移以及塑性区的发展控制效果有限,应控制锚杆自由段长度在塑性区内。

古金赤水河大桥主桥总体设计

古金赤水河大桥主桥为(83.5+173.5+575+173.5+83.5)m半飘浮体系双塔双索面斜拉桥。主梁采用双边主梁断面钢-混组合梁,由工字钢主梁和混凝土桥面板组成,全宽43.8 m,设置裙板抑制主梁涡振。桥塔为下塔柱内收的A形塔,南、北塔塔高分别为217 m和261 m。由于山区超高桥塔塔墩景观效果欠佳,采用超高塔柱无塔墩方案,桥塔采用嵌岩群桩基础;针对山区桥梁养护不便的情况,索塔锚固采用耐候钢钢锚梁;针对剪力钉在拉拔力作用下承载能力降低问题,采用以开孔板连接件为主的钢-混结合构造实现锚梁牛腿壁板与塔壁连接。斜拉索采用公称直径15.20 mm、标准抗拉强度1860 MPa的钢绞线拉索,全桥共4×23对(184根),空间双索面扇形布置。由于斜拉索锚拉板+外置减振阻尼器景观效果不佳,选用全内置减振阻尼器方案。

考虑多失效模式的桩锚结构鲁棒性设计及经济性优化

目的 研究岩土力学参数的不确定性对桩锚支护体系的整体影响,探究经济性和鲁棒性共同作用的优化设计。方法 选取黄土地区工程案例,考虑支护桩隆起破坏、支护桩倾覆破坏、整体稳定性破坏三类破坏形式,使用蒙特卡洛及点估计法嵌套的方式求出不同设计组合下的失效概率及标准差;同时考虑优化设计的经济性,筛选出桩锚支护结构体系的鲁棒性优化设计方案。结果 随着桩长增加,主控模式由隆起破坏向整体稳定性改变,不同的几何参数对结构鲁棒性影响不同,优化后可以获得同时满足经济性、鲁棒性及可靠度要求的最佳设计方案。结论 在桩锚结构设计中考虑经济性优化及多失效模式的鲁棒性设计是必要的。

从网络主播的形象设计看色彩设计的情感传递

本文从网络主播形象设计的色彩设计入手,从个人形象设计中色彩的形象信息、情感信息、审美信息3个方面阐述网络主播形象设计中色彩设计的情感传递。准确地分析判断设计对象气质形象的特征,恰当巧妙地运用色彩的信息传达,充分发挥色彩的各种作用,注重色彩的情感表达、形象塑造以及审美法则等要素,平衡各要素之间的关系,才能创造出完美、和谐、生动且富有个性的个人形象。

深江铁路洪奇沥公铁两用大桥主桥方案构思与总体设计

深江铁路洪奇沥公铁两用大桥主桥采用(3×100+808+3×100)m超短边跨钢-混组合混合梁斜拉桥,一跨跨越通航水域。该桥公铁分层布置,上层布置8车道城市快速路,下层布置4线铁路。主梁采用倒梯形双主桁截面,桥面布置紧凑、受力明确、经济性好。中跨主梁采用板桁-箱桁组合结构钢梁,桥面结构参与主桁受力,具有高效综合性能。边跨主梁采用矩形钢管混凝土叠合板-桁组合梁,融结构受力和锚固压重于一体,叠合板采用32 cm厚预制板+40 cm厚现浇层。钢-混结合段采用“钢格室+承压板”构造,钢-混结合面位于桥塔向中跨侧4.6 m。桥塔采用H形混凝土塔,基础采用35根直径4.0 m的大直径钻孔灌注桩。斜拉索采用标准抗拉强度2000 MPa的平行钢丝成品索,最大规格为PES(C)7-547。索梁锚固采用副桁弦杆节点兜底钢锚箱结构,传力可靠、抗疲劳性能好。索塔锚固创新地采用自平衡交叉混合锚固技术,以适应大规格斜拉索锚固。钢桁梁采用“纵向分段、横向分区”制造、运输、现场吊装的施工方案。

公铁混合布置大跨度斜拉桥主梁断面形式研究--以赣江公铁大桥西支主桥设计为例

以赣江公铁两用大桥西支主桥设计为例,研究一种适应上层8车道公路、下层对称双线铁路+4车道公路混合布置的主梁断面形式。提出带挑臂双索面箱桁组合断面、带挑臂单索面箱桁组合断面、矩形箱桁组合断面、矩形钢桁梁断面4种主梁断面方案,采用有限元软件分析各方案静动力性能及受力特点,综合考虑方案构造特点、技术指标、工程数量、公铁运营安全、景观效果等,确定该桥选用带挑臂双索面箱桁组合断面。该桥斜拉索最大索力16000 kN,锚固在下层钢箱梁两侧,通过有限元实体分析对锚拉板和钢锚箱式两种索梁锚固形式进行比选研究,钢锚箱形式受力合理、应力水平低、经济性好,设计采用钢锚箱形式。带挑臂双索面箱桁组合断面桥面空间布置合理、下层公铁行车干扰小、梁端竖向变形最小、经济性好,是一种适应公铁混合布置大跨度斜拉桥主梁断面形式。

渐进式滑坡锚索抗滑桩预应力张拉值计算

依据渐进式滑坡蠕变特点,现有锚索抗滑桩计算模型针对渐进式滑坡桩–锚–土三者相互作用过程考虑较少。针对这一问题,将渐进式滑坡缓慢失稳的变形特征和预应力锚索抗滑桩从空载到满载动态工作过程相结合,利用Winkler弹性地基梁理论,优化了锚索抗滑桩桩–锚变形协调条件,考虑桩后土压力渐进变化过程,构建不同工况桩–锚–土协同工作的计算模型,推导了预应力锚索抗滑桩施工阶段初张拉值的计算方法。结合工程算例和有限元软件数值模拟结果,为获取较高精度的计算数值,采用MATLAB软件编译程序进行计算分析。结果表明:1)渐进式滑坡“稳定–蠕动–失稳”阶段性变形特点决定了预应力锚索抗滑桩“空载–加载–满载”三阶段桩–锚动态内力变形过程,明确了各阶段桩后可能存在的土压力模型,单纯进行满载阶段锚索拉力设计不符合渐进式滑坡实际作用机理,进一步证明施工阶段锚索预应力张拉值设计的重要性;2)渐进式滑坡推力由尚未产生的初始空载阶段至完全作用的满载阶段,两阶段并非互相独立存在,二者通过桩–锚变形协调条件相互作用,表明了施工阶段抗滑桩预应力张拉力值大小受满载阶段桩锚内力及变形大小的影响;3)依据渐进式滑坡锚索抗滑桩动态内力变形过程,保证抗滑桩受荷段和锚固段内力大小均衡相等,优化了满载阶段全桩弯矩平衡设计原则,确立了以静止土压力作为施工阶段预应力张拉值设计标准,对比表明,此计算方法优于其余4种现有算法,同时有限元数值模拟结果与本文算法贴合度较高,进一步验证了此计算方法的合理性和可靠性。研究成果可为渐进式滑坡中预应力锚索抗滑桩的设计计算和施工提供技术指导。

一种新型中空注浆锚杆止浆塞的优化设计与试验研究

锚杆在隧道施工中应用广泛,对于提高围岩自承能力,减小结构受力效果显著,中空注浆锚杆经过注浆后可以大幅提高其支护效应,注浆质量直接影响中空锚杆的承载能力。基于一种新型中空注浆锚杆止浆塞,通过数值模拟对其构造形式和结构尺寸进行优化设计研究,并通过室内模型试验和现场试验对研发的新型止浆塞的排气稳压效果进行检验。结论如下:止浆塞最优尺寸为内塞排气槽上端宽8.0 mm,深1.5 mm,下端宽11.3 mm,深1.0 mm;闭气坎高度为3 mm;外塞孔口端直径为51 mm,远离孔口端直径为50 mm。止浆塞对不同锚杆孔孔径具有普适性,当止浆塞与锚杆孔相差0~4 mm时,均能满足其稳压止浆性能要求。试验结果表明,新型止浆塞稳压压力在0.7~1.2 MPa之间,锚杆孔内浆液充盈,浆液密实,止浆效果明显。

掘锚机外喷雾系统的改进设计

外喷雾系统是掘锚机的重要部分,位于截割部上方,对改善工作环境有着非常重要的作用。针对现有外喷雾系统的不足,通过增大系统的压力和流量、改变喷水座、喷嘴的形状和布置方式等方法,设计出一种新型的全断面外喷雾系统,并对其结构和具体实施方案进行详细的阐述。

粘土中的螺旋锚上拔承载力模拟试验及设计优化

为深入研究锚盘间距、锚盘外径以及锚盘数量等结构因素对螺旋锚极限承载力的影响。基于螺旋锚基础设计公式,结合数值模拟推断出类圆柱剪切和类单锚盘失效破坏模式,提出并修订了原有设计方法。研究结果表明,螺旋锚的极限承载力受到锚盘间距、锚盘外径和锚盘数量的影响。优化配置可以显著提高螺旋锚的承载力,并且可以节约材料用量。此外,根据破坏模式重新阐述了圆柱剪切和单锚盘失效破坏,有助于进一步理解黏性土壤中螺旋锚的受力行为,为输电线路工程中螺旋锚基础的设计和实施提供了一定的理论参考。

Bond Mechanical Properties of Glass Fiber Reinforced Polymer Anti-Floating Anchor in Concrete Baseplate

Combined with fiber Bragg grating(FBG)sensing technology,four glass fiber reinforced polymer(GFRP)anti-floating anchors and four steel anti-floating anchors were tested for on-site destructive failure to investigate the anchoring performance and the bonding characteristics between GFRP anti-floating anchor and concrete floor.The test results show that bending GFRP anchor will be broken at the common boundary between vertical anchorage section and bending section during the pullout process,and the spring-back load provided by the rupture contributes to a decrease of bearing capacity and an inflection point on the load-slip curve.The loaddisplacement curve of the straight anchor GFRP anti-floating anchor is smoother and has better predictability than the same type of steel anchor.Additionally,different forms of GFRP anti-floating bolt have different bondslip constitutive relations.By introducing the sliding-slip correction factor of bending bolt,constitutive models describing the rising-section of sliding-slip relation of bending and straight-anchored GFRP anti-floating bolt are established respectively.The model can fit the test results rightly.

椭圆塔空间缆自锚式悬索桥主索鞍系统设计研究

在建万龙大桥工程主桥为世界首座采用椭圆钢桥塔的空间主缆自锚式悬索桥。该桥鞍座采用铸焊结合的自适应式空间缆索主索鞍,鞍座存在以下技术难点:空间主缆主索鞍受力复杂;椭圆塔纵向刚度大,主索鞍的抗滑问题突出;鞍座底部为柔性支撑,索鞍与主塔协同变形,塔-鞍连接结构传力复杂。为掌握椭圆塔空间缆自锚式悬索桥主索鞍及塔-鞍连接结构的关键技术,运用数值分析方法开展系统研究。研究结论如下:(1)当桥梁承受(恒载+汽车+人群+自来水+温度+风)作用时,满足要求的最小摩擦系数μ为0.215,需要设置12 mm竖向摩擦板;(2)主索鞍在最大缆力工况下的最大Von Mises应力为186.2 MPa,最大竖向变形为1.572 mm,满足强度及刚度要求;(3)主索鞍与钢塔连接结构主要通过支承隔板以竖向剪力的形式将主索鞍作用力传至钢塔腹板上,端部支承隔板的剪力显著大于中间隔板,剪力传递的不均匀系数为1.29;(4)主索鞍支承板在鞍座区域的边缘存在一定转角,空缆工况最大纵向转角为0.366‰rad,在鞍座顶推施工中需要加以考虑。

HRB400钢筋与UHPC锚固可靠度分析及锚固设计研究

为给桥梁工程中HRB400钢筋与超高性能混凝土(Ultra-High Performance Concrete,UHPC)锚固设计提供依据,对两者间的粘结性能及锚固长度进行研究。根据中心拔出试验中54个不同参数HRB400钢筋与UHPC锚固试件的粘结强度结果,回归得到粘结强度计算公式;在此基础上利用中心点法进行锚固可靠度分析与基本锚固长度计算,并与国内外规范基本锚固长度计算结果进行对比。结果表明:《混凝土结构设计规范》(GB 50010-2010)和CEB-FIB Model Code 2010计算的基本锚固长度接近,与中心点法相比偏大、偏安全;基于锚固长度计算结果,给出不同保护层厚度下基本锚固长度和钢筋断裂最小锚固长度建议值;提出UHPC相对保护层厚度为0.5时,可采用《混凝土结构设计规范》计算HRB400钢筋与UHPC基本锚固长度和钢筋断裂最小锚固长度;UHPC相对保护层厚度为1.0、1.5、2.0时,可通过修正《混凝土结构设计规范》计算结果取值,基本锚固长度修正系数分别可取0.8、0.65、0.55,钢筋断裂最小锚固长度修正系数分别可取0.85、0.7、0.6。

对掘锚机机载临时支护结构的设计改进

临时支护装置作为掘锚机最为重要的组成部分,其本身的结构与功能会直接影响到煤矿的开采安全。所以,为了最大限度地保证煤矿开采安全,以及掘锚作业人员的人身安全,切实解决掘锚机机载支护问题刻不容缓。鉴于此,本文笔者在总结了相关参考文献的基础上,对煤矿井下地质情况加以分析,提出满足煤矿井下实际作业条件的掘锚机机载临时支护结构设计改进思路,以期为广大同行在掘锚机今后的升级改造工作上提供有益的参考借鉴。

建宁县某水厂边坡支护与排水设计

依托于建宁县某新建水厂边坡支护工程,采用动态设计法对场地的填方段边坡和挖方段边坡进行支护和排水设计,通过对安全性、施工难度、经济性、稳定性、效果等对比分析,最终选择挖方段边坡采用框架锚杆支护,而填方段边坡采用抗滑桩+锚索和挡土墙联合支护方案以及采用地表集水明排+坡体软式透水管或泄水管泄水的排水设计,采用极限平衡法验证了支护后的边坡稳定性。