Experimental Study on the Electrochemical Performance of PEMFC under Different Assembly Forces

Proton exchange membrane fuel cell(PEMFC)is of paramount significance to the development of clean energy.The components of PEMFC are assembled using many pairs of nuts and bolts.The assembly champing bolt torque is critical to the electrochemical performance and mechanical stability of PEMFC.In this paper,a PEMFC with the threechannel serpentine flow field was used and studied.The different assembly clamping bolt torques were applied to the PEMFC in three uniform assembly bolt torque and six non-uniform assembly bolt torque conditions,respectively.And then,the electrochemical performance experiments were performed to study the effect of the assembly bolt torque on the electrochemical performance.The test results show that the assembly bolt torque significantly affected the electrochemical performance of the PEMFC.In uniform assembly bolt torque conditions,the maximal power density increased initially as the assembly bolt torque increased,and then decreased on further increasing the assembly torque.It existed the optimum assembly torque which was found to be 3.0 N·m in this work.In non-uniform assembly clamping bolt torque conditions,the optimum electrochemical performance appeared in the condition where the assembly torque of each bolt was closer to be 3.0 N·m.This could be due to the change of the contact resistance between the gas diffusion layer and bipolar plate and mass transport resistance for the hydrogen and oxygen towards the catalyst layers.This work could optimize the assembly force conditions and provide useful information for the practical PEMFC stack assembly.

Numerical Study on the Effect of Gap Diffraction on the Hydrodynamic Performance of A Floating Breakwater

Two-dimensional(2D)flume experiments are useful in investigating the performances of floating breakwaters(FBs),including hydrodynamic performances,motion responses,and mooring forces.Designing a reasonable gap between the flume wall and the FBs is a critical step in 2D flume tests.However,research on the effect of the gap on the accuracy of 2D FB experimental results is scarce.To address this issue,a numerical wave tank is developed using CFD to estimate the wave-FB interaction of a moored dual-cylindrical FB,and the results are compared to experimental data from a previously published work.There is good agreement between them,indicating that the numerical model is sufficiently accurate.The numerical model is then applied to explore the effect of gap diffraction on the performance of FBs in2D experiments.It was discovered that the nondimensional gap length L_(Gap)/W_(Pool)should be smaller than 7.5%to ensure that the relative error of the transmission coefficient is smaller than 3%.The influence of the gap is also related to the entering wave properties,such as the wave height and period.

Development of Experiential Live-action Performance Products in Tai’an City:A Case Study of“Chinese Taishan·Fengshan Grand Ceremony”

Live-action performances are a new form of performances that combine culture and tourism.The rise of live-action performance products has brought new vitality to the development of tourism,has strong development potential,can better meet the needs of tourists for immersive experience,and maintain long-term development of tourism in a region.In this paper,a live-action tourism performance product“Chinese Taishan·Fengshan Grand Ceremony”was studied to discuss the development of experiential live-action tourism performance products in Tai’an City.Through the investigation and data statistics of tourists,by using the experience economy theory,tourist experience theory,statistical analysis and other means,some strategies for the development of live-action tourism performance products in Tai’an City were proposed to promote the development of tourism performance products in Tai’an City.

Influence of Blade Wrap Angle on Centrifugal Pump Performance by Numerical and Experimental Study

The existing research on improving the hydraulic performance of centrifugal pumps mainly focuses on the design method and the parameter optimization. The traditional design method for centrifugal impellers relies more on experience of engineers that typically only satisfies the continuity equation of the fluid. In this study, on the basis of the direct and inverse iteration design method which simultaneously solves the continuity and motion equations of the fluid and shapes the blade geometry by controlling the wrap angle, three centrifugal pump impellers are designed by altering blade wrap angles while keeping other parameters constant. The three-dimensional flow fields in three centrifugal pumps are numerically simulated, and the simulation results illustrate that the blade with larger wrap angle has more powerful control ability on the flow pattern in impeller. The three pumps have nearly the same pressure distributions at the small flow rate, but the pressure gradient increase in the pump with the largest wrap angle is smoother than the other two pumps at the design and large flow rates. The pump head and efficiency are also influenced by the blade wrap angle. The highest head and efficiency are also observed for the largest angle. An experiment rig is designed and built to test the performance of the pump with the largest wrap angle. The test results show that the wide space of its efficiency area and the stability of its operation ensure the excellent performance of the design method and verify the numerical analysis. The analysis on influence of the blade wrap angle for centrifugal pump performance in this paper can be beneficial to the optimization design of the centrifugal pump.

Numerical and Experimental Studies on the Propulsion Performance of A Wave Glide Propulsor

This paper introduces a newly developed Unmanned Wave Glide Vehicle （UWGV）, which is driven only by extracting energy from gravity waves, and presents a comprehensive study on the propulsion performance of the UWGV＇s propulsor-Wave Glide Propulsor （WGP） in a regular wave. By simplifying the WGP as six 2D tandem asynchronous flapping foils （TAFFs）, a CFD method based on Navier-Stokes equations was first used to analyze the hydrodynamic performance of TAFFs with different parameters of non-dimensional wave length rn and non-dimensional wave height n. Then, a series of hydrodynamic experiments were performed. The computational results agree well with the experimental results when n〈0.07 and both of them show the thrust force and input power of the WGP are larger at smaller m or larger n. By analyzing the flow field of TAFFs, we can see that a larger m is beneficial to the forming, merging and shredding of the TAFFs＇ vortices; as TAFFs are arranged in tandem and have the same motions, the leading edge vortex and wake vortex of the TAFFs are meaningful for improving the thrust force of their adjacent ones.

Model experiment on anti-deformation performance of a self-supporting transmission tower in a subsidence area

A large number of high-voltage power transmission towers have recently been constructed in mining areas prone to subsidence. In order to ensure the safety of the transmission towers and the safe operation of transmission systems, it is imperative to carry out research on the anti-deformation performance of transmission towers. In our study, we performed experiments on the anti-deformation performance of a transmission tower in a subsidence area on a scale model with a geometric scale ratio of 1:5 and analyzed the failure mechanism of the tower members. The results show that, when the axial distance between two supports changes, destabilization failure most likely occurs in the members of the bottom transverse layer because some parts of the main diagonal member bars yield under the action of compression. The failure mechanism of the tower members basically coincides with the lever principle.

Environmental regulation and firms'performance:a quasi-natural experiment from China

This paper investigates whether environmental regulation affects firm's performance including productivity,wage and employment using firm-level data in 1996-2007.The identification uses Two Control Zones(TCZ)policy implemented by the Chinese government in 1998,in which tougher environmental regulations were imposed in TCZ cities but not others.By difference-indifferences estimation,we find that tougher environmental regulation leads to larger increase on both total factor productivity and wage,and firms tend to employ fewer workers under pressure of environmental protection.Heterogeneous tests show that the impacts are better for nonpollution intensive firms,non-exporters and SOEs.Finally,we find that R&D input and exiting firms among industry are the driving forces for enhancing TFP and increasing wage and unemployment.

Influence of specific speed on hydraulic performances and pressure fluctuations in mixed-flow pumps

A series of steady and unsteady numerical calculations of the internal flow in mixed-flow pumps with three different specific speeds were carried out based on the N-S equation coupled with the standard k-εturbulence model under different operating conditions to investigate the relationship between the impeller specific speed and the pump performance as well as pressure pulsations.Meanwhile,the pump performance and pressure pulsations inside the mixed-flow pump with three different specific speeds were also analyzed and compared with the corresponding test data.From the results,the averaged deviations between the predicted and tested head among different impellers are below 5%,and with respect to the equivalent impeller specific speeds of 280 and 260,the values are 4.30%and 3.69%,respectively.For all the impeller schemes,the best efficiency point of the mixed-flow pump is found at the flow rate of 1.2 Q_(d) and the higher head deviation occurs at lower flow rates.Especially,it can be found that the specific speed has a slight effect on the pressure fluctuation in the impellers.Eventually,it is determined that the pump performance curves calculated by numerical simu-lations have good agreement with the relevant experimental results,which verifies that the numerical methods used in the present study are accurate to a certain extent.Furthermore,the results also provide some references to the pressure pulsation analysis and the performance improvement of the mixed-flow pump design.

Hydrodynamic Performance and Power Absorption of A Coaxial DoubleBuoy Wave Energy Converter

As an important wave energy converter(WEC),the double-buoy device has advantages of wider energy absorption band and deeper water adaptability,which attract an increasing number of attentions from researchers.This paper makes an in-depth study on double-buoy WEC,by means of the combination of model experiment and numerical simulation.The Response Amplitude Operator(RAO)and energy capture of the double-buoy under constant power take-off(PTO)damping are investigated in the model test,while the average power output and capture width ratio(CWR)are calculated by the numerical simulation to analyze the influence of the wave condition,PTO,and the geometry parameters of the device.The AQWA-Fortran united simulation sy stem,including the secondary developme nt of AQWA software coupled with the flowchart of the Fortran code,models a new dynamic system.Various viscous damping and hydraulic friction from WEC system are measured from the experimental results,and these values are added to the equation of motion.As a result,the energy loss is contained in the final numerical model the by united simulation system.Using the developed numerical model,the optimal period of energy capture is identified.The power capture reaches the maximum value under the outer buoy's natural period.The paper gives the peak value of the energy capture under the linear PTO damping force,and calculates the optimal mass ratio of the device.

Effect of Glycyrrhiza Polysacchride on Growth Performance and Immunity Function of Mice

Aniso-dose glycyrrhiza polysaccharide was injected into abdominal cavity of mice. The effect of glycyrrhiza polysaccharide on growth performance and immune ruction of mice was determined. The results showed that the growth performance and immune function of mice were improved and there were significant differences among the treatment groups and control group.

Studies on Aerodynamic Behavior and Performance of Aerospike Nozzles

Experimental and numerical studies are carried out on a 6-cell tile-shaped aerospike nozzle, a 6-cell aerospike nozzle with round-to-rectangle primary nozzles and a 1-cell linear aerospike nozzle. Good altitude compensation capacities and high efficiencies are obtained in the tests. The efficiencies of 6-cell tile-shaped aerospike nozzle and 1-cell linear aerospike nozzle at design altitude approach to 100 %, and that of 6-cell aerospike nozzle with round-to-rectangle primary nozzles in the same condition is about 95 % due to the imperfect cell contour and manufacturing defects. Numerical results are in good agreements with test data. The effects of ambient pressure on exhaust and then on base behavior are analyzed, The effects of variation in the amount of base bleed on performance are also examined in the tests.

A Comparative Study on Hydrodynamic Performance of Double Deflector Rectangular Cambered Otter Board

In the present work,the hydrodynamic performance of the double deflector rectangular cambered otter board was studied using wind tunnel experiment,flume tank experiment and numerical simulation.Results showed that the otter board had a good hydrodynamic performance with the maximum lift-to-drag ratio(K_(MAX) = 3.70).The flow separation occurred when the angle of attack(AOA) was at 45?,which revealed that the double deflector structure of the otter board can delay the flow separation.Numerical simulation results showed a good agreement with experiment ones,and could predict the critical AOA,which showed that it can be used to study the hydrodynamic performance of the otter board with the advantage of flow visualization.However,the drag coefficient in flume tank was much higher than that in wind tunnel,which resulted in a lower lift-to-drag ratio.These may be due to different fluid media between flume tank and wind tunnel,which result in the big difference of the vortexes around the otter board.Given the otter boards are operated in water,it was suggested to apply both flume tank experiment and numerical simulation to study the hydrodynamic performance of otter board.

Experimental study on seismic behavior of semi-rigid connection between steel beam and concrete wall

Beam-column or beam-wall connections are an important problem in high-rise buildings. In this study, based on the analysis of an example structure, an analytical model for design of the semi-rigid connections between steel beams and RC walls in high-rise hybrid buildings is proposed. Also, the mechanical characteristics of these connections subjected to low-reversed cyclic loading are investigated through comparison of experimental results from three semi-rigid connections and two rigid connections. Moreover, some latent problems for design of these connections as well as the corresponding solutions are discussed. The results from the experiments and analyses indicate that semi-rigid connections exhibit satisfactory capacity and seismic performance, and the proposed design can be used in practice.

Performance comparison for oil-water heat transfer of circumferential overlap trisection helical baffle heat exchanger

The performance tests were conducted on oil–water heat transfer in circumferential overlap trisection helical baffle heat exchangers with incline angles of 12°, 16°, 20°, 24° and 28°, and compared with a segmental baffle heat exchanger. The results show that the shell side heat transfer coefficient h_o and pressure drop Δp_o both increase while the comprehensive index h_o/Δp_o decreases with the increase of the mass flow rate of all schemes. And the shell side heat transfer coefficient, pressure drop and the comprehensive index ho/Δpo decrease with the increase of the baffle incline angle at a certain mass flow rate. The average values of shell side heat transfer coefficient and the comprehensive index h_o/Δp_o of the 12° helical baffled scheme are above 50% higher than those of the segmental one correspondingly, while the pressure drop value is very close and the ratios of the average values are about 1.664 and 1.596, respectively. The shell-side Nusselt number Nu_o and the comprehensive index Nu_o·Eu_(zo)^(-1) increase with the increase of Reynolds number of the shell side axial in all schemes, and the results also demonstrate that the small incline angled helical scheme has better comprehensive performance.

Experiment on mechanical properties of steel fiber reinforced concrete and application in deep underground engineering

Specimens of steel fiber reinforced concrete （SFRC） in volume ratios of 0%, 0.5%, 1% and 1.5% were prepared to study the supporting effect of SFRC at these diffterent volume ratios in a deep soft rock tunnel. Experiments with mechanical properties of compressive strength in cubic specimens, cleave strength in cylindrical specimens and four-point flexure strength of sheet metal specimens were carded out. The experimental results indicate that SFRC in a volume ratio of 1% is superior in ranking to other volume ratios in terms of technique and economics. By means of a numerical simulation, given the characteristics of soft rock deformation and damage at great depth, a new support substitution scheme of SFRC to replace plain concrete is proposed. The results of an industrial trial show that the support provided by SFRC can withstand large deformations of the surrounding rock. Good resuits have been obtained in a practical anplication.

Flexural failure experiment on cracked PC simply supported box girders

Long-term load and flexural failure experiments are carried out on two prestressed concrete(PC) simply supported box girders. In the long-term load experiment, girder-1(G1) is in an elastic state, while girder-2(G2) is in a cracking state. To investigate the influence of cracking on the flexural behaviors of PC simply supported box beams, the experiment results are analyzed from many aspects, such as load–deflection, load–strain, and failure mode. Experiment results show the following: 1) the shrinkage and creep of concrete have considerable influences on the long-term deflection and strain of the two girders; 2) in the flexural failure experiment, the cracks and ultimate loads of the two girders are close. The rigidity degeneration of G2 is significantly faster than that of G1, and thus G2 shows nonlinear characteristics earlier; 3) to prove the validity and rationality of the current code, the cracking load and ultimate load of the two girders are calculated according to the current code.

WRIST FORCE SENSOR'S DYNAMIC PERFORMANCE CALIBRATION BASED ON NEGATIVE STEP RESPONSE

Negative step response experimental method is used in wrist force sensor＇s dynamic performance calibration. The exciting manner of negative step response method is the same as wrist force sensor＇s load in working. This experimental method needn＇t special experiment equipments. Experiment＇s dynamic repeatability is good. So wrist force sensor＇s dynamic performance is suitable to be calibrated by negative step response method. A new correlation wavelet transfer method is studied. By wavelet transfer method, the signal is decomposed into two dimensional spaces of time-frequency. So the problem of negative step exciting energy concentrating in the low frequency band is solved. Correlation wavelet transfer doesn＇t require that wavelet primary function be orthogonal and needn＇t wavelet reconstruction. So analyzing efficiency is high. An experimental bench is designed and manufactured to load the wrist force sensor orthogonal excitation force/moment. A piezoelectric force sensor is used to setup soft trigger and calculate the value of negative step excitation. A wrist force sensor is calibrated. The pulse response function is calculated after negative step excitation and step response have been transformed to positive step excitation and step response. The pulse response function is transferred to frequency response function. The wrist force sensor＇s dynamic characteristics are identified by the frequency response function.

Experimental investigation on the energy-saving diffuser of a main fan

The main fan diffuser in a coal mine is an energy-recycling equipment with a dynamic energy loss for the main fan. Engineering practices and related researches show that the body structures of three types of diffusers are irrational. To solve the problem, an energy-saving diffuser is designed on the basis of the velocity potential theory. Under conditions of inlet velocity from 7 m/s to 32 m/s, 7 condition experiments using the energy-saving diffuser of 2.31 AER （area-enlarging ratio） and 5 condi- tion experiments using the energy-saving diffuser of 2.00 AER were conducted. Through a comparative analysis of the experi- ments, the results show that the COP （coefficient of performance） of the energy-saving diffuser of 2.31 AER is better than that of the energy-saving diffuser of 2.00 AER.

Design of Calibration Experiments for Identification of Manipulator Elastostatic Parameters

The paper is devoted to the elastostatic calibration of industrial robots, which is used for precise machining of large-dimensional parts made of composite materials. In this technological process, the interaction between the robot and the workpiece causes essential elastic deflections of the manipulator components that should be compensated by the robot controller using relevant elastostatic model of this mechanism. To estimate parameters of this model, an advanced calibration technique is applied that is based on the non-linear experiment design theory, which is adopted for this particular application. In contrast to previous works, it is proposed a concept of the user-defined test-pose, which is used to evaluate the calibration experiments quality. In the frame of this concept, the related optimization problem is defined and numerical routines are developed, which allow generating optimal set of manipulator configurations and corresponding forces/torques for a given number of the calibration experiments. Some specific kinematic constraints are also taken into account, which insure feasibility of calibration experiments for the obtained configurations and allow avoiding collision between the robotic manipulator and the measurement equipment. The efficiency of the developed technique is illustrated by an application example that deals with elastostatic calibration of the serial manipulator used for robot-based machining.