Preparation,Characterization and Electronic Properties of Fluorine-doped Tin Oxide Films

Tin oxide（SnO2） and fluorine doped tin oxide（FTO） films were prepared on glass substrates by sol-gel spin-coating using SnCl4 and NH4F precursors.Fluorine doping concentration was fixed at 4 at%and 20 at%by controlling precursor sol composition.Films exhibited the tetragonal rutile-type crystal structure regardless of fluorine concentration.Uniform and highly transparent FTO films,with more than 85%of optical transmittance,were obtained by annealing at 600℃.Florine doping of films was verified by analyzing the valence band region obtained by XPS.It was found that the fluorine doping affects the shape of valence band of SnO2 films.In addition,it was observed that the band gap of SnO2 is reduced as well as the Fermi level is upward shifted by the effect of fluorine doping.

Preparation and Characterization of Transparent Conductive Zinc Doped Tin Oxide Thin Films Prepared by Radio-frequency Magnetron Sputtering

High transparent and conductive thin films of zinc doped tin oxide （ZTO） were deposited on quartz substrates by the radio-frequency （RF） magnetron sputtering using a 12 wt% ZnO doped with 88 wt% SnO2 ceramic target.The effect of substrate temperature on the structural,electrical and optical performances of ZTO films has been studied.X-ray diffraction （XRD） results show that ZTO films possess tetragonal rutile structure with the preferred orientation of （101）.The surface morphology and roughness of the films was investigated by the atomic force microscope （AFM）.The electrical characteristic （including carrier concentration,Hall mobility and resistivity） and optical transmittance were studied by the Hall tester and UV- VIS,respectively.The highest carrier concentration of -1.144×1020 cm-3 and the Hall mobility of 7.018 cm2（V ·sec）-1 for the film with an average transmittance of about 80.0% in the visible region and the lowest resistivity of 1.116×10-2 Ω·cm were obtained when the ZTO films deposited at 250 oC.

Investigation of UV photosensor properties of Al-doped SnO_(2) thin films deposited by sol-gel dip-coating method

Transparent conducting aluminum doped tin oxide thin films were prepared by sol-gel dip coating method with differ-ent Al concentrations and characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), UV-Vis spectrophotometry and photoconductivity study. The variation observed in the properties of the measured films agrees with a difference in the film's thickness, which decreases when Al concentration augments. X-ray diffraction analysis reveals that all films are polycrystal-line with tetragonal structure, (110) plane being the strongest diffraction peak. The crystallite size calculated by the Debye Scher-rer’s formula decreases from 11.92 to 8.54 nm when Al concentration increases from 0 to 5 wt.%. AFM images showed grains uni-formly distributed in the deposited films. An average transmittance greater than 80% was measured for the films and an en-ergy gap value of about 3.9 eV was deduced from the optical analysis. Finally, the photosensitivity properties like current-voltage characteristics, ION/IOFF ratio, growth and decay time are studied and reported. Also, we have calculated the trap depth energy using the decay portion of the rise and decay curve photocurrent.

Preparation of High Quality Indium Tin Oxide Film on a Microbial Cellulose Membrane Using Radio Frequency Magnetron Sputtering

Microbial cellulose （MC） membranes produced by Acetobacter xylinum NUST4.1,were used as flexible substrates for the fabrication of transparent indium tin oxide （ITO） electrodes.Transparent and conductive ITO thin films were deposited on MC membrane at room temperature using radio frequency （RF） magnetron sputtering.The optimum ITO deposition conditions were achieved by examining crystalline structure,surface morphology and op-toelectrical characteristics with X-ray diffraction （XRD）,scanning electron microscopy （SEM）,atomic force mi-croscopy （AFM）,and UV spectroscopy.The sheet resistance of the samples was measured with a four-point probe and the resistivity of the film was calculated.The results reveal that the preferred orientation of the deposited ITO crystals is strongly dependent upon with oxygen content （O2/Ar,volume ratio） in the sputtering chamber.And the ITO crystalline structure directly determines the conductivity of ITO-deposited films.High conductive [sheet resis-tance ～120 Ω·square-1 （Ω·sq-1）] and transparent （above 76%） ITO thin films （240 nm thick） were obtained with a moderate sputtering power （about 60 W） and with an oxygen flow rate of 0.25 ml·min-1 （sccm） during the deposi-tion.These results show that the ITO-MC electrodes can find their potential application in optoelectrical devices.

Electrical and optical properties of indium tin oxide/epoxy composite film

The electrical and optical properties of the indium tin oxide （ITO）/epoxy composite exhibit dramatic variations as functions of the ITO composition and ITO particle size. Sharp increases in the conductivity in the vicinity of a critical volume fraction have been found within the framework of percolation theory. A conductive and insulating transition model is extracted by the ITO particle network in the SEM image, and verified by the resistivity dependence on the temperature. The dependence of the optical transmittance on the particle size was studied. Further decreasing the ITO particle size could further improve the percolation threshold and light transparency of the composite film.

Effects of annealing process on characteristics of fully transparent zinc tin oxide thin-film transistor

Annealing effect on the performance of fully transparent thin-film transistor （TTFT）, in which zinc tin oxide （ZnSnO） is used as the channel material and SiO2 as the gate insulator, is investigated. The ZnSnO active layer is deposited by radio frequency magnetron sputtering while a SiO2 gate insulator is formed by plasma-enhanced chemical vapor deposition. The saturation field-effect mobility and on/off ratio of the TTFT are improved by low temperature annealing in vacuum. Maximum saturation field-effect mobility and on/off ratio of 56.2 cm2/（V.s） and 3×10^5 are obtained, respectively. The transfer characteristics of the ZnSnO TPT are simulated using an analytical model and good agreement between measured and the calculated transfer characteristics is demonstrated.

Low Temperature DC Sputtering Deposition on Indium-Tin Oxide Film and Its Application to Inverted Top-emitting Organic Light-emitting Diodes

Indium tin oxide （ITO） ultrathin films were prepared on glass substrate by DC （direct current） magnetron sputtering technique with the assistance of H2O vapor to avoid potential surface damage. The film properties were characterized by X-ray diffraction （XRD） technique, four-point probe method and spectrophotometer. The results show that the deposited ITO film with introduced H2O during sputtering process was almost amorphous. The average visible light transmission of 100 nm ITO film was around 85% and square resistivity was below 80 Ω/square. The film was used as the transparent anode to fabricate an inverted top-emitting organic light-emitting diodes （IT-OLEDs） with the structure of glass substrate/Alq3 （40 nm）/NPB （15 nm）/CuPc （x nm）/ITO anode （100 nm）, where the film thickness of CuPc was optimized. It was found that the luminance of this IT-OLEDs was improved from 25 cd/m^2 to more than 527 cd/m^2 by increasing the thickness of CuPc, and luminance efficiency of 0.24 lm/W at 100 cd/m^2 was obtained, which indicated that the optimized thickness of CuPc layer was around 15 nm.

Infrared laser-induced fast photovoltaic effect observed in orthorhombic tin oxide film

The SnO_2/SnO with an orthorhombic structure is a material known to be stable at high pressures and temperatures and expected to have new optical and electrical properties. The authors report a new finding of the infrared laser induced a fast photovoltaic effect arising from orthorhombic tin oxide film with an indirect band gap（~2.4 e V） which is deposited by pulsed laser deposition. The rising time of the photovoltaic signal is about 3 ns with a peak value of 4.48 mV under the pulsed laser beam with energy density 0.015 m J/mm^2. The relation between the photovoltages and laser positions along the line between two electrodes of the film is also exhibited. A possible mechanism is put forward to explain this phenomenon.All data and analyses demonstrate that the orthorhombic tin oxide with an indirect band gap could be used as a candidate for an infrared photodetector which can be operated at high pressures and temperatures.

Spray Pyrolysis Deposition of Single and Mixed Oxide Thin Films

The influence of processing parameters is investigated on the structural characteristics of single and mixed oxides produced by spray pyrolysis technique. The films were synthesized by spraying precursor solutions through a noz-zle onto a heated alumina substrate. The precursor consisted separately of aqueous solutions of tin chloride for SnO2 and zinc chloride for ZnO for single oxide cases, and aqueous solutions of tin chloride and indium nitrate for SnO2 + In2O3 and zinc chloride and indium nitrate solutions for ZnO + In2O3 for mixed oxide cases. The substrate temperature was varied accordingly for each single and mixed case. The films produced were characterized by X-ray Photoelectron Spectroscopy and Scanning Electron Microscopy. The results indicate that a non-homogenous film is formed at low temperature for both single oxides considered. The temperature has significant effect on the composition of the synthesized films of both single oxides below 450℃. The results for mixed oxides show that the best homogeneous films are obtained for 80 wt% ZnO + 20 wt% In2O3, and 80 wt% SnO2 + 20 wt% In2O3.

Preparation of indium tin oxide targets with a high density and single phase structure by normal pressure sintering process

The present work mainly describes the technology for preparing indium-tin oxide （ITO） targets by cold isostatic pressing （CIP） and normal pressure sintering process. ITO powders were produced by chemical co-precipitation and shaped into an ITO green compact with a relative density of 60% by CIP under 300 MPa. Then, an ITO target with a relative density larger than 99.6% was obtained by sintering this green compact at 1550℃ for 8 h. The effects of forming pressure, sintering temperature and sintering time on the density of the target were inves- tigated. Also, a discussion was made on the sintering atmosphere.

Influence of reflow processing conditions on the uniformity of the chromium passivation film on tinplate

This study aims to systematically analyze the key parameters of the reflow process that influence the uniformity of the chromium passivation film coated on tinplate. The distribution characteristics of the chromium passivation film coated on the tinplate surface under different treatment conditions were systematically characterized using the scanning Kelvin probe technique, X-ray photoelectron spectroscopy, and X-ray diffraction. Results indicate that the use of flux reduces the porosity of tin coating, thereby favoring the uniform growth of the passivation film. Furthermore, an increase in the reflow power and quenching temperature facilitates the homogeneous distribution of the passivation film on the tinplate surface,particularly when treated with electrolytic cathodic sodium dichromate.

Enhancement and Optimization of ATO Nano-crystalline Films Properties by the Addition of Acetylacetone as Modifier in the Sol-gel Process

Sb-doped Sn O2(ATO) thin films have been prepared using the spin coating method by selecting the proper amount of acetylacetone as solution modifier. All ATO powders and films exhibited the cassiterite rutile-like structure in a crystal size below 10 nm under all the experimental conditions and a nonpreviously reported crystal structure was observed at high acetylacetone loads. The acetylacetone molar ratio influenced notably the optical and electrical properties of ATO films. When prepared at an acetylacetone molar ratio of 4, ATO films exhibited optical transparencies above 90% in the visible region and above 40% in the UV region for thicknesses of 100 and 300 nm. Films in a thickness of 100 nm and at an annealing temperature of 650 ℃ accounted for a high transparency of 97% in the visible wavelength. Films prepared at an acetylacetone molar ratio of 4 exhibited an electric resistivity of 1.33×10-3 Ω·cm at an annealing temperature of 650 ℃. The optimal Sb content for ATO films was found to be 8 at%. The relationships among the properties of starting solutions, the experimental parameters, and properties of ATO films are discussed.

Effect of surfactants on the structure and photoelectric properties of ITO films by sol-gel method

The Indium tin oxide（ITO） thin film possesses excellent photoelectric properties that enable it to act as an ideal transparent conductor.To obtain high-quality ITO films through sol-gel method, the ionic surfactant monoethanolamine and the non-ionic surfactant polyethylene glycol（PEG） were added to the ITO precursor slurry.The influences of surfactants on the structural and photoelectric properties of ITO film samples were investigated.XRD patterns indicated that surfactant monoethanolamine contributed to film predominant grain orientation along the（400） plane.The high transmittance（over 95%） was attributed to the preferred orientation and the grain size expansion of ITO films.SEM showed that the surface particle size and the morphology of ITO films were strongly dependent on the kind of surfactants used.Moving to the shortwave region, the absorption edge of the films exhibited the Burstein-Moss shift.

DOPED SnO_2 FILMS GROWN BY THE METALLORGANIC CHEMICAL VAPOUR DEPOSITION TECHNIQUE

1 INTRODUCTIONStannic oxide as a wide-band gap semiconductor（Eg≈3.5eV）,has high transparency in thevisible spectral region（index of refraction,n≈1.9）and resistance to acids and bases at roomtemperature.The SnO2 thin film.the most useful form in application,has been prepared by avariety of physical and chemical deposition processes.It has been found that undoped SnO2films have high resistivity(about 108--15Ω·cm)at room temperature[1].For manyapplications requiring not too low sheet resistance。

模压成型压力对氧化铟锡(ITO)靶材性能影响研究

以化学共沉淀-煅烧法制备的纳米ITO粉体为原料,通过模压、冷等静压成型,采用常压烧结法制备了ITO靶材,研究了模压成型压力对ITO靶材相对密度、电阻率和晶粒尺寸的影响。结果表明,模压成型压力60 MPa且烧结条件适宜时,制得的ITO靶材相对密度为99.81%、电阻率为1.707×10^(-4)Ω·cm、平均晶粒尺寸为7.62μm。研究结果可为ITO靶材的致密化与大型化生产提供借鉴。

Influence of Annealing Temperature on the Microstructure and Electrical Properties of Indium Tin Oxide Thin Films

Indium tin oxide （ITO） thin films were prepared on alumina ceramic substrates by radio frequency magnetron sputtering. The samples were subsequently annealed in air at temperatures ranging from 500 to 1,100 ℃ for 1 h. The influences of the annealing temperature on the microstructure and electrical properties of the ITO thin films were investigated, and the results indicate that the as-deposited ITO thin films are amorphous in nature. All samples were crystallized by annealing at 500 ~C. As the annealing temperature increases, the predominant orientation shifts from （222） to （400）. The carrier concentration decreases initially and then increases when the annealing temperature rises beyond 1,000 ℃. The resistivity of the ITO thin films increases smoothly as the annealing temperature increases to just below 900 ℃. Beyond 900 ℃, however, the resistivity of the films increases sharply. The annealing temperature has a significant effect on the stability of the ITO/Pt thin film thermocouples （TFTCs）. TFTCs annealed at 1,000 ℃ show improved high- temperature stability and Seebeck coefficients of up to 77.73 pV/℃.

Facile synthesis of graphitic carbon-nitride supported antimony-doped tin oxide nanocomposite and its application for the adsorption of volatile organic compounds

Antimony-doped tin oxide(ATO) nanoparticles with an average size of ～ 6 nm were prepared by co-precipitation and subsequent heat treatment. Graphitic carbon nitride(g-CN)/ATO hybrid nanocomposite was designed by the combination of thermally synthesized g-CN and ATO nanoparticles by ultrasonication. The materials were characterized using N2 adsorption/desorption(BET), X-ray diffraction(XRD), scanning electron microscopy(SEM), energy dispersive spectroscopy(EDS), transmission electron microscopy(TEM) and Fourier transform infrared spectroscopy(FTIR). A mixture of five volatile organic compounds(VOCs, chloroform, benzene, toluene, xylene and styrene) was used to compare the adsorption capacity of the samples. The adsorption capacity of ATO nanoparticles was improved by the addition of g-CN. Experimental data showed that, among the five VOCs,chloroform was the least adsorbed, regardless of the samples. The g-CN/ATO showed nearly three times greater adsorption capacity for the VOC mixture than pure ATO. The unchanged efficiency of VOC adsorption during cyclic use demonstrated the completely reversible adsorption and desorption behavior of the nanocomposite at room conditions. This economically and environmentally friendly material can be a practical solution for outdoor and indoor VOC removal.

Preparation and characteristics of Nb-doped indium tin oxide thin films by RF magnetron sputtering

Niobium-doped indium tin oxide （ITO：Nb） thin films are fabricated on glass substrates by radio frequency （RF） magnetron sputtering at different temperatures. Structural, electrical and optical properties of the films are investigated using X-ray diffraction （XRD）, atomic force microscopy （AFM）, ultraviolet-visible （UV-VIS） spectroscopy and electrical measurements. XRD patterns show that the preferential orientation ofpolycrystalline structure changes from （400） to （222） crystal plane, and the crystallite size increases with the increase of substrate temperature. AFM analyses reveal that the film is very smooth at low temperature. The root mean square （RMS） roughness and the average roughness are 2.16 nm and 1.64 nm, respectively. The obtained lowest resistivity of the films is 1.2 × 10^4 Ω-cm, and the resistivity decreases with the increase of substrate temperature. The highest Hall mobility and carrier concentration are 16.5 cmVV.s and 1.88× 10^21 cm^-3, respectively. Band gap energy of the films depends on substrate temperature, which is varied from 3.49 eV to 3.63 eV.

射频磁控溅射工艺参数对掺钨氧化铟锡透明导电薄膜性能的影响

ITO薄膜是目前应用最为广泛的透明导电薄膜,通过在ITO中掺杂其他金属可以进一步改善ITO薄膜的光学和电学性能。本文采用射频(RF)磁控溅射法制备了掺钨氧化铟锡(ITO∶W)透明导电薄膜,研究了薄膜厚度、表面形貌、晶体结构以及光学和电学性能与各溅射参数之间的关系。当溅射功率大于40 W时,制备的ITO∶W薄膜为方铁锰矿结构的多晶薄膜,此时薄膜表面光滑平整而且具有良好的结晶性。在基板温度320℃、溅射功率80 W、溅射时间15 min、工作气压0.6 Pa条件下得到了光学和电学性能优良的ITO∶W薄膜,其方块电阻为10.5Ω/、电阻率为4.41×10^(-4)Ω·cm,对应的载流子浓度为2.23×10^(20)cm^(-3)、迁移率为27.3 cm^(2)·V^(-1)·s^(-1)、可见光(400~700 nm)范围内平均透射率为90.97%。此外,本研究还发现通过调节基板温度影响氧元素的状态可以改变ITO∶W薄膜的电学性能。

Crystalline Structure and Surface Morphology of Tin Oxide Films Grown by DC Reactive Sputtering

Tin oxide thin films were deposited by direct current （DC） reactive sputtering at gas pressures of 0.015 mbar - 0.15 mbar. The crystalline structure and surface morphology of the prepared SnO2 films were introduced by X-ray diffraction （XRD） and atomic force microscopy （AFM）. These films showed preferred orientation in the （110） plane. Due to AFM micrographs, the grain size increased non-uniformly as the working gas pressure increased.