A preliminary analysis of arcuate structures-relationship of the island arc and deep-sea trench to the dip angle of Benioff zone

The origin of arcuate islands and deep-sea trenches has been studied for a long time and various interpretations have been proposed. In this paper, some analytical models are put forward from a geometrical viewpoint and then the theoretical dip angles of the underthrusting slabs of circum-Pacific island arcs are computed and compared with those of the Benioff zone. As a result, it is found that the dip angle of the underthrusting slab is one of the main factors determining the curvature of the arcuate structure. The authors consider that this result may contribute to the plate theory.

Characteristics analyzing and parametric modeling of the arc sound in CO_2 GMAW for on-line quality monitoring

For on-line monitoring of welding quality, the characteristics of the arc sound signals in short circuit CO2 GMAW were analyzed in the time and frequency domains. The arc sound presents a series of ringing-like oscillations that occur at the end of short circuit i. e. the moment of arc re-ignition, and distributes mainly in the frequency band below 10 kHz. A concept of the arc tone channel and its equivalent electrical model were suggested, which is considered a time-dependent distributed parametric system of which the transmission properties depend upon the geometric and physical characteristics of the arc and surroundings, and is excited by the sound source results from the change of arc energy so that results in arc sound. The linear prediction coding （ LPC ） model is an estimation of the tone channel. The radial basis function （ RBF ） neural networks were built for on-line pattern recognition of the gas-lack in welding, in which the input vectors were formed with the LPC coefficients. The test results proved that the LPC model of arc sound and the RBF networks are feasible in on-line quality monitoring.

PHYSICAL VALUE MAPPING ALGORITHM OF MESH IN FINE CAE ANALYSIS OF AUTOMOBILE BODY STRUCTURE

A physical value mapping （PVM） algorithm based on finite element mesh from the stamped part in stamping process to the product is presented, In order to improve the efficiency of the PVM algorithm, a search way from the mesh of the product to the mesh of the stamped part will be adopted. At the same time, the search process is divided into two steps： entire search （ES） and local search （LS）, which improve the searching efficiency. The searching area is enlarged to avoid missing projection elements in ES process. An arc-length method is introduced in LS process. The validity is confirmed by the results of the complex industry-forming product.

Contact Resistance and Arc Erosion of Tungsten-copper Contacts in Direct Currents

The arc erosion under medium direct currents in the argon flow was tested on tungsten-copper（W-Cu） contacts which were processed by hot extrusion and heat treatment. The scanning electron microscopy（SEM） and transmission electron microscopy（TEM） were used to study the microstructure of the W-Cu powders and compacts. The contact resistance, arcing energy, and arcing time were continuously measured by JF04C contact materials test system. Changes in tungsten-copper contact surface were observed by SEM. The test results showed that the arcing time and arcing energy all increase with current and voltage, but the changes of average contact resistance are more complicated. For a short arcing time, the average contact resistance decreases with increasing current due to the vaporization of Cu. However, for a longer arcing time, it slightly increases due to the formation of high resistant films, compound copper tungsten. The formation of compound copper tungsten was confirmed by the increased Rc kept in the range from 1.1 to 1.6 mΩ. The compound copper tungsten is first exposed with a tungsten and copper-rich surface, and then totally exposed due to evaporation of copper from the surface. At last a stabilized surface is created and the crystals decrease from 8 μm to 2 μm caused by the arc erosion.

On the Arc Consistency Problem

In this paper, we propose a new arc consistency algorithm, AC-8,which requires less computation time and space than AC-6 and AC-7. The main ideaof the optimization is the divide-and-conquer strategy, thereby decomposing an arcconsistency problem into a series of smaller ones and trying to solve them in sequence.In this way, not only the space complexity but also the time complexity can be reduced. The reason for this is that due to the ahead of time performed inconsistencypropagation (in the sense that some of them are executed before the entire inconsis-tency checking has been finished), each constraint subnetwork will be searched with agradually shrunk domain. In addition, the technique of AC-6 can be integrated intoour algorithm, leading to a further decrease in computational complexity.