Investigation of paint removal by atmospheric pressure plasma jet

Acrylic polyurethane paint on the surface of 2A12 Al alloy was cleaned utilizing an atmospheric pressure plasma jet in this work.The dynamic evolution of the paint removal process during plasma treatment with time was explored through analysis of morphology and chemical states.The results showed that although the thickness of paint could be reduced effectively with an increase in cleaning time,the removal rate of paint gradually decreased with time.During the initial cleaning process range,its original smooth morphology of paint turned rugged quickly and was almost unchanged with further plasma treatment.Element and chemical state analysis showed that the content of C in the paint layer decreased obviously after plasma treatment.In contrast,the O content increased remarkably.The cleaning mechanism could be mainly attributed to the reaction between active O-containing species in air plasma and organic components in the paint.After removal of superficial organic matter,residue inorganic metal oxide substances aggregated on the base.The exposed metal oxides on the one hand elevated the superficial O content,but on the other hand hindered further plasma penetration,resulting in a gradual decrease in cleaning rate with cleaning time.Therefore,physical wiping was proposed to be incorporated with the plasma method and effective removal of paint was realized.

Compared discharge characteristics and film modifications of atmospheric pressure plasma jets with two different electrode geometries

Atmospheric pressure plasma jet shows great potential for polymer film processing. The electrode geometry is the key factor to determine discharge characteristics and film modification of jets. In this paper, we compared the discharge characteristics and the film modifications of atmospheric pressure plasma jets with needle-ring electrode(NRE) and doublering electrode(DRE). The results show that jet with NRE has stronger electric field intensity and higher discharge power,making it present more reactive oxygen particles and higher electron temperature, but its discharge stability is insufficient.In contrast, the jet with DRE has uniform electric field distribution of lower field intensity, which allows it to maintain stable discharge over a wide range of applied voltages. Besides, the modification results show that the treatment efficiency of PET film by NRE is higher than that by DRE. These results provide a suitable atmospheric pressure plasma jets device selection scheme for polymer film processing process.

The effects of radio frequency atmospheric pressure plasma and thermal treatment on the hydrogenation of TiO_(2) thin film

The effects of radio frequency(RF)atmospheric pressure(AP)He/H_(2)plasma and thermal treatment on the hydrogenation of TiO_(2)thin films were investigated and compared in this work.The color of the original TiO_(2)film changes from white to black after being hydrogenated in He/H_(2)plasma at160 W(gas temperature~381℃)within 5 min,while the color of the thermally treated TiO_(2)film did not change significantly even in pure H_(2)or He/H_(2)atmosphere with higher temperature(470℃)and longer time(30 min).This indicated that a more effective hydrogenation reaction happened through RF AP He/H_(2)plasma treatment than through pure H_(2)or He/H_(2)thermal treatment.The color change of TiO_(2)film was measured based on the Commission Internationale d’Eclairage L*a*b*color space system.Hydrogenated TiO_(2)film displayed improved visible light absorption with increased plasma power.The morphology of the cauliflower-like nanoparticles of the TiO_(2)film surface remained unchanged after plasma processing.X-ray photoelectron spectroscopy results showed that the contents of Ti3+species and Ti-OH bonds in the plasma-hydrogenated black TiO_(2)increased compared with those in the thermally treated TiO_(2).X-ray diffraction(XRD)patterns and Raman spectra indicated that plasma would destroy the crystal structure of the TiO_(2)surface layer,while thermal annealing would increase the overall crystallinity.The different trends of XRD and Raman spectra results suggested that plasma modification on the TiO_(2)surface layer is more drastic than on its inner layer,which was also consistent with transmission electron microscopy results.Optical emission spectra results suggest that numerous active species were generated during RF AP He/H_(2)plasma processing,while there were no peaks detected from thermal processing.A possible mechanism for the TiO_(2)hydrogenation process by plasma has been proposed.Numerous active species were generated in the bulk plasma region,accelerated in the sheath region,and bumped toward the TiO_(2)film,which will react with the TiO_(2)surface to form OVs and disordered layers.This leads to the tailoring of the band gap of black TiO_(2)and causes its light absorption to extend into the visible region.

Atmospheric pressure pulsed modulated arc discharge plasma

Direct-current(DC)arc plasma has great application values in the field of the chemical industry,but it has the problem of low energy efficiency.Facing the requirement for improving the energy efficiency of the arc,this paper proposes a unique method of pulsed modulated arc(PMA).This method uses high-frequency pulses and reduces the arc current to improve the control of electron temperature.The electrical characteristics,optical characteristics and products are tested.The test results show that during the PMA process,all of the experimental results which include voltage,current and light will significantly increase.These results are analyzed from the perspective of functionality,repeatability and energy conversion.The analysis results show that although the PMA method does not show good parameter consistency,it has potential application prospects because it increases the energy conversion rate by 4.5%and 8%from the perspective of light and products,respectively.

A homogeneous atmospheric pressure air plasma in a 10 mm gap based on a three-electrode configuration

Generation of atmospheric pressure homogeneous air plasma in a large gap(>4 mm)is a challenge.In this study,an atmospheric pressure homogeneous air plasma generated in a gap up to 10 mm is reported,which is based on a three-electrode configuration,where a high-voltage(HV)electrode and a middle electrode form a surface dielectric barrier discharge(S-DBD),and together with the ground electrode form the main volume discharge.High-speed photographs confirm that the discharge in the main gap is homogeneous.The gas temperature of the plasma estimated from the N_(2)(C^(3)∏_(u)-B^(3)∏_(g))(Δv=-2)emission is about 320 K,which is close to room temperature.A detailed analysis shows that the discharge ignited between the HV electrode and the middle electrode is serving as an electron source,and the electrons deposited on the dielectric plate are due to the S-DBD along with the applied voltage generating a driving force,which results in a high concentration of seed electrons in the main gap and induces the homogeneous plasma.Further analysis shows that the electric field in the main gap is only about18.45 k V·cm^(-1),which is much lower than the typical breakdown electric field of 30 k V·cm^(-1)for atmospheric pressure air discharge.

Enhanced antibacterial activity of cotton via silver nanocapsules deposited by atmospheric pressure plasma jet

In this work,the antibacterial activity of cotton containing silver nanocapsules prepared by atmospheric pressure plasma(APP)deposition is investigated.The nanocapsules consist of a shell and a silver nanoparticle(Ag NP)core,where the core is used to bring antibacterial activity,and the shell is utilized to suppress the potential toxicity of Ag NPs.The surface morphology and the elements of the samples are analyzed by scanning electron microscopy(SEM),energy dispersive x-ray and x-ray photoelectron spectroscopy(XPS).The SEM results show that the skin of the cotton fibers will fall off gradually after APP treatment over 3 min,and the XPS results show that the Ag content will rise to 1.6%after APP deposition for 10 min.Furthermore,the antimicrobial activity tests show that the reduction rates of Escherichia coli and Staphylococcus aureus can achieve 100%when the sample is treated for 10 min,which exhibits excellent antibacterial activity.In addition,the UV absorption properties of the cotton will also be correspondingly improved,which brings a broader application prospect for antibacterial cotton.

Use of a Microwave Plasma Process at Atmospheric Pressure for Bacterial Inactivation without Thermal Effects

An atmospheric microwave plasma argon was used for the inactivation of bacteria E. coli. The employed device, called Axial Injection Torch (or TIA for Torche à Injection Axiale), consisted of a microwave power source, a waveguide and a gas supply system. Using this argon plasma source, we studied the effects of the exposure time, the exposure distance, the input power, and the gas flow rate on the reduction rate of Escherichia coli cells. The first part of the study was carried out with a static sample exposed to the plasma and then in the second part the sample was set in motion relative to the plasma jet. A log reduction number of E. coli of 4 (10-4 CFU/mL) was obtained with UV and active species, for UV only a log of 1 (10-1 CFU/mL) was obtained.

Discharge and mass transfer characteristics of atmospheric pressure gas-solid two-phase gliding arc

In this work,a gas-solid two-phase gliding arc discharge(GS-GAD)reactor was built.Gliding arc was formed in the gap between the blade electrodes,and solid powder was deposited on the sieve plate positioned beneath the blade electrodes.A range of experimental parameters,including the inter-electrode spacing,gas flow rate,applied voltage,and the type of the powder,were systematically varied to elucidate the influence of solid powder matter on the dynamics of gliding arc discharge(GAD).The discharge images were captured by ICCD and digital camera to investigate the mass transfer characteristics of GS-GAD,and the electrical parameters,such as the effective values of voltage,current,and discharge power were record to reveal the discharge characteristics of GS-GAD.The results demonstrate that powder undergoes spontaneous movement towards the upper region of the gliding arc due to the influence of electric field force.Increasing the discharge voltage,decreasing relative dielectric constant of the powder and reducing the electrode-to-sieve-plate distance all contribute to a greater involvement of powder in the GAD process,subsequently resulting in an enhanced powder concentration within the GAD region.Additionally,powder located beneath the gliding arc experiences downward resistance caused by the opposing gas flow and arc.Excessive gas flow rate notably hampers the powder concentration within the discharge region,and the velocity of powder motion in the upper part of the GAD region is reduced.Under the condition of electrode-to-sieve-plate distance of 30 mm,gas flow rate of 1.5 L/min,and peak-to-peak voltage of 31 kV,the best combination of arc gliding and powder spark discharge phenomena can be achieved with the addition of Al_(2)O_(3) powder.

Hydrogen Permeation Characteristics of Pd-CuMembrane in Plasma Membrane Reactor

Hydrogen is an alternative energy source that has the potential to replace fossil fuels.One of the hydrogen applications is as a material for Polymer Electrolyte Membrane Fuel Cells(PEMFC)in fuel cell vehicles.High-purity hydrogen can be obtained using a hydrogen separation membrane to prevent unwanted contaminants from potentially harming the PEMFC components.In this study,we fabricated a plasma membrane reactor and investigated the permeation performance of a hydrogen separation membrane in a plasma membrane reactor utilizing atmospheric pressure plasma.The result showed the hydrogen permeation rate increasing with time as reactor temperature is increased through joule heating.By decreasing the gap length of the reactor from 2 to 1 mm,the hydrogen permeation rate increases by up to 40%.The hydrogen permeation rate increases by 30%when pressure is applied to the plasma membrane reactor by up to 100 kPa.

Atmospheric Pressure Plasma Jet in Ar and O_2/Ar Mixtures:Properties and High Performance for Surface Cleaning

An atmospheric pressure plasma jet generated in Ar and O2/Ar mixtures has been investigated by specially designed equipment with double power electrodes at 20~32 kHz, and their effects on the cleaning of surfaces have been studied. Properties of the jet discharge are studied by electrical diagnostics, including the waveform of discharge voltage, discharge current and the Q-V Lissajous figures. The optical emission spectroscopy is used to measure the plasma parameters, such as the excitation temperature and the gas temperature. It is found that the consumed power and the excitation temperature increase with increase of the discharge frequency. On the other hand, at the same discharge frequency, these parameters in O2/Ar mixture plasma are found to be much larger. The effect on surface cleaning is studied from the changes in the contact angle. For Ar plasma jet, the contact angle decreases with increase of the discharge frequency. For O2/Ar mixture plasma jet, the contact angle decreases with increase of discharge frequency up to 26 kHz, however, further increase of discharge frequency does not show further decrease in the contact angle. At the same discharge frequency, the contact angle after O2/Ar mixture plasma cleaning is found to be much lower compared to the case of pure Ar. From the results of quadrupole mass-spectrum analysis, we can identify more fragment molecules of CO and H2O in the emitted gases after O2/Ar plasma jet treatment compared with Ar plasma jet treatment, which are produced by the decomposition of surface organic contaminants during the cleaning process.

In vitro study of nonthermal atmospheric pressure plasma in improving the durability of the dentin–adhesive interface with an etch-and-rinse system

In this study, we employed a nonthermal atmospheric pressure plasma(NTAPP) jet to evaluate the effect of plasma treatment on the durability of resin–dentin bonding under a thermocycling challenge. Furthermore, we assessed the degradation resistance of plasma-treated collagen under a sodium hypochlorite(NaClO) challenge. We assessed the beneficial effect of NTAPP treatment on the acid-etched dentin–bonding interface by testing the micro-tensile bond strength and examining the morphology. We found that the immediate bonding strength of the dentin significantly increased after NTAPP treatment. Compared with the control group, NTAPP resulted in a more prominent effect on the bonding durability of the dentin–adhesive interface after treatment for 5 or 10 s. Simultaneously, the mechanical strength of dentin collagen under the NaClO challenge was improved. Our results indicate that, in optimal conditions, NTAPP could be a promising method to protect dentin collagen and to improve the bonding durability between dentin and etch-and-rinse adhesives.

Experimental Study on Surface Dielectric Barrier Discharge Plasma Actuator with Different Encapsulated Electrode Widths for Airflow Control at Atmospheric Pressure

The surface dielectric barrier discharge （SDBD） plasma actuator has shown great promise as an aerodynamic flow control device. In this paper, the encapsulated electrode width of a SDBD actuator is changed to study the airflow acceleration behavior. The effects of encapsulated electrode width on the actuator performance are experimentally investigated by measuring the dielectric layer surface potential, time-averaged ionic wind velocity and thrust force. Experimental results show that the airflow velocity and thrust force increase with the encapsulated electrode width. The results can be attributed to the distinct plasma distribution at different encapsulated electrode widths.

Atmospheric pressure gliding arc discharge plasma treatments for improving germination, growth and yield of wheat

Wheat （Triticum aestivum） seeds were treated with atmospheric pressure gliding arc discharge plasmas to investigate the effects on water absorption, seed germination rate, seedling growth and yield in wheat. The surface architectures and functionalities of the seeds were found to modify due to plasma treatments. 6 rain treatment was provided 95%-100% germination rate. For the treatment duration of 3 and 9 rain the growth activity, dry matter accumulation, leaves chlorophyll contents, longest spikes, number of spikes/spikelet and total soluble protein content in shoots were improved. The grain yield of wheat was increased ,--20% by 6 min treatment with H2O/O2 plasma with respect to control.

Three different low-temperature plasma-based methods for hydrophilicity improvement of polyethylene films at atmospheric pressure

Three different low-temperature plasma-based methods were used to improve the surface hydrophilicity of polyethy- lene （PE） films, and all the modification processes were carried out by employing an atmospheric pressure plasma jet （APPJ） system. （a） PE films were directly modified by APPJ using a gas mixture of He and 02. （b） Acrylic acid （AA） was introduced into the system and a polymer acrylic acid （PAA） coating was deposited onto the PE films. （c） AA was grafted onto the PE surface activated by plasma pre-treatment. It was found that the hydrophilicity of the PE films was significantly improved for all the three methods. However, the samples modified by Process （a） showed hydrophobicity recovery after a storage time of 20 days while no significant change was found in samples modified by Process （b） and Process （c）. The Fourier transform infrared spectroscopy （FTIR） results indicated that the most intensive C=O peak was detected on the PE surface modified by Process （c）. According to the X-ray photoelectron spectroscopy （XPS） analysis, the ratios of oxygen-containing polar groups for samples modified by Process （b） and Process （c） were higher than that modified by Process （a）.

Applications of atmospheric pressure plasma in microbial inactivation and cancer therapy: a brief review

Atmospheric pressure cold plasma, with advantages such as high particle activity, no thermal damage, high efficiency and direct and friendly contact with human tissues, is considered to have great potential in biomedical applications. Therefore, 'plasma medicine' as a new interdiscipline has been developed in the past two decades. This review first briefly describes the development of typical plasma sources suitable for biomedical applications, and those with different discharge forms are simply compared, evaluated and summarized. Subsequently, measurement of the crucial gaseous reactive particles(e.g. OH and O) and their spatio-temporal distributions are introduced. Meanwhile, the generation and variation rules and the related critical macroscopic parameters of the plasma-induced aqueous reactive species are summarized. Finally, related studies in the last ten years on the mechanisms of the plasma-driven microbial inactivation and plasma-induced apoptosis of cancer cells are introduced. Moreover, some scientific problems that need to be urgently solved in the field of plasma medicine are also discussed. This review will provide useful guidance for future related research.

Cold atmospheric-pressure air plasma treatment of C6 glioma cells:effects of reactive oxygen species in the medium produced by the plasma on cell death

An atmospheric-pressure air plasma is employed to treat C6 glioma cells in vitro. To elucidate on the mechanism causing cell death and role of reactive species （RS） in the medium produced by the plasma, the concentration of the long-lived RS such as hydrogen peroxide, nitrate, and ozone in the plasma-treated liquid （phosphate-buffered saline solution） is measured. When vitamin C is added to the medium as a ROS quencher, the viability of C6 glioma cells after the plasma treatment is different from that without vitamin C. The results demonstrate that reactive oxygen species （ROS） such as H2O2, and O3 constitute the main factors for inactivation of C6 glioma cells and the reactive nitrogen species （RNS） may only play an auxiliary role in cell death.

Surface Decontamination of Chemical Agent Surrogates Using an Atmospheric Pressure Air Flow Plasma Jet

An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experi- mental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination pro-cess, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride （PVC）, polyethylene （PE）, phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chroma- tism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.

Efficacy of Atmospheric Pressure Plasma as an Antibacterial Agent Against Enterococcus Faecalis in Vitro

Enterococcus faecalis （E. faecalis） is a microorganism that can survive extreme challenges in obturated root canals. The aim of this study was to evaluate the efficacy of a non-thermal atmospheric pressure plasma plume against E. faecalis in vitro. A non-thermal atmospheric pressure plasma jet device which could generate a cold plasma plume carrying a peak current of 300 mA was used. The antibacterial efficacy of this device against E. faecalis and its biofihn un- der different conditions was detected. The antibacterial efficacy of the plasma against E. faecalis and Staphylococcus aureus （S. aureus） was also evaluated. After plasma treatment, the average diameter of inhibition zone on S. aureus and E. faecalis was 2.62±0.26 cm and 1.06±0.30 cm, respectively （P 〈 0.05）. The diameter was increased with prolongation of the treatment dura- tion. The diameters of inhibition zone of the sealed Petri dishes were larger than those of the uncovered Petri dishes. There was significant difference in colony-forming units between plasma group and control group on E. faecalis biofilm （P 〈 0.01）. The transmission electron microscopy revealed that the ultrastructural changes eytoderm of E. faecalis were observed after treatment for 2min. It is concluded that the non-thermal atmospheric pressure plasma could serve as an effective adjunct to standard endodontie microbial treatment.

Development of a new atmospheric pressure cold plasma jet generator and application in sterilization

This paper reports that a new plasma generator at atmospheric pressure, which is composed of two homocentric cylindrical all-metal tubes, successfully generates a cold plasma jet. The inside tube electrode is connected to ground, the outside tube electrode is connected to a high-voltage power supply, and a dielectric layer is covered on the outside tube electrode. When the reactor is operated by low-frequency （6 kHz-20 kHz） AC supply in atmospheric pressure and argon is steadily fed as a discharge gas through inside tube electrode, a cold plasma jet is blown out into air and the plasma gas temperature is only 25-30℃. The electric character of the discharge is studied by using digital real-time oscilloscope （TDS 200-Series）, and the discharge is capacitive. Preliminary results are presented on the decontamination of E.colis bacteria and Bacillus subtilis bacteria by this plasma jet, and an optical emission analysis of the plasma jet is presented in this paper. The ozone concentration generated by the plasma jet is 1.0× 10^16cm^-3 which is acquired by using the ultraviolet absorption spectroscopy.

On the green aurora emission of Ar atmospheric pressure plasma

The Ar atmospheric pressure plasma was found to be an excellent laboratorial source for green aurora emission.However,the characteristic and production mechanism of the green aurora emission of the Ar atmospheric pressure plasma are still not clear.In this work,an Ar plasma in a long glass tube which emits intense green aurora light is investigated.With the long glass tube,it can be concluded that the green aurora emission in the Ar plasma is not owing to the mixture of Ar plasma plume with the surrounding air.It is also found that the green aurora emission often appeared beyond the active electrode when the active electrode is placed at the downstream of the gas flow.The green emission disappears when the traces amount of O_(2) or N_(2)(about 0.05%–0.07%)is added to Ar.This is because the O_(2) molecules deactivate the upper state O(^(1)S),which results in the decrease of the green emission.On the other hand,when N_(2) is added,Ar metastable atoms are quenched by N_(2),which results in the decrease of O atoms and eventually leads to the decrease of the green emission intensity.The intensity of the green aurora emission increases when the driving voltage frequency increases from 1 to 10 k Hz.More importantly,it is found that the green aurora emission is not affected when a grounded stainless steel needle is in contact with the plasma plume.Thus,the green emission is not driven electrically.All these findings are helpful for the understanding of the physics and its applications of atmospheric pressure plasma jet in space physics,laser physics and other application areas.