Experimental Study on Surface Dielectric Barrier Discharge Plasma Actuator with Different Encapsulated Electrode Widths for Airflow Control at Atmospheric Pressure

The surface dielectric barrier discharge （SDBD） plasma actuator has shown great promise as an aerodynamic flow control device. In this paper, the encapsulated electrode width of a SDBD actuator is changed to study the airflow acceleration behavior. The effects of encapsulated electrode width on the actuator performance are experimentally investigated by measuring the dielectric layer surface potential, time-averaged ionic wind velocity and thrust force. Experimental results show that the airflow velocity and thrust force increase with the encapsulated electrode width. The results can be attributed to the distinct plasma distribution at different encapsulated electrode widths.

Effects of Oxygen Concentration on Pulsed Dielectric Barrier Discharge in Helium-Oxygen Mixture at Atmospheric Pressure

In this work the effects of O_2 concentration on the pulsed dielectric barrier discharge in helium-oxygen mixture at atmospheric pressure have been numerically researched by using a one-dimensional fluid model in conjunction with the chosen key species and chemical reactions.The reliability of the used model has been examined by comparing the calculated discharge current with the reported experiments. The present work presents the following significant results. The dominative positive and negative particles are He_2~＋ and O_2^-, respectively, the densities of the reactive oxygen species（ROS） get their maxima nearly at the central position of the gap, and the density of the ground state O is highest in the ROS. The increase of O_2 concentration results in increasingly weak discharge and the time lag of the ignition. For O_2 concentrations below 1.1%,the density of O is much higher than other species, the averaged dissipated power density presents an evident increase for small O_2 concentration and then the increase becomes weak. In particular,the total density of the reactive oxygen species reaches its maximums at the O_2 concentration of about 0.5%. This characteristic further convinces the experimental observation that the O_2 concentration of 0.5% is an optimal O_2/He ratio in the inactivation of bacteria and biomolecules when radiated by using the plasmas produced in a helium oxygen mixture.

Preparation of Diamond-like Carbon Film Assisted in the Plasma of Dielectric Barrier Discharge at Atmospheric Pressure

Dielectric barrier discharge at atmospheric presure has been applied to prepare hydrocarbon films on large- area glass and silicon substrates. When hydrogen and methane mixture(2:1) is used as discharge gas and the substrate is heated to 300 C, hard hydrogenated amorphous carbon film is deposited. From the IR deconvolution analysis of the C-H stretching absorption for the coating, the hydrocarbon group ration (CH3:CH2:CH) and C-C bond type ratio (sp3c/sp2c) are about 10%: 21%: 69% and 3:1~6:1,respectively. Their Knoop hardness is up to 10Gpa. No film isdeposited when the content of methane in the mixed gases is decreased to 5% at 300 C silicon substrate.

Nanosecond Repetitively Pulsed Dielectric Barrier Discharge in Air at Atmospheric Pressure

Dielectric barrier discharge （DBD） between two cylindrical glass containers with salt water generated by a nanosecond repetitively pulsed power generator is reported. The electrical parameters, luminous images and spectrum diagnosis are presented. It is shown that the DBD possesses a large discharge current and an intense optical emission from the nitrogen second positive system below 400 nm. The gas temperature remains very close to room temperature regardless of pulse polarity. Luminous photographs with a short exposure time down to 2 ns indicate that no filament is observed and the discharge is homogeneous.

Generation of reactive species in atmospheric pressure dielectric barrier discharge with liquid water

Atmospheric pressure helium/water dielectric barrier discharge（DBD） plasma is used to investigate the generation of reactive species in a gas–liquid interface and in a liquid. The emission intensity of the reactive species is measured by optical emission spectroscopy（OES）with different discharge powers at the gas–liquid interface. Spectrophotometry is used to analyze the reactive species induced by the plasma in the liquid. The concentration of OH radicals reaches 2.2 μm after 3 min of discharge treatment. In addition, the concentration of primary longlived reactive species such as H;O;, NO;and O;are measured based on plasma treatment time.After 5 min of discharge treatment, the concentration of H;O;, NO;, and O;increased from 0 mg?·?L;to 96 mg?·?L;, 19.5 mg?·?L;, and 3.5 mg?·?L;, respectively. The water treated by plasma still contained a considerable concentration of reactive species after 6 h of storage. The results will contribute to optimizing the DBD plasma system for biological decontamination.

Deposition of Thin Titania Films by Dielectric Barrier Discharge at Atmospheric Pressure

A homogeneous atmospheric pressure dielectric barrier discharge is studied. It is in argon with small admixtures of titanium tetrachloride vapour and oxygen for the deposition of thin titania films on glass substrates. A special electrode configuration was applied in order to deposit the titania film uniformly. The sustaining voltage （6 kV to 12 kV）, current density （about 3 mA/cm^2） and total optical emission spectroscopy were monitored to characterize the discharge in the gap of 2 mm. Typical deposition rates ranged from approximately 30 nm/min to 120 nm/min. The film morphology was investigated by using scanning electron microscopy （SEM） and the composition was determined with an energy dispersive x-ray spectroscopy （EDS） analysis tool attached to the SEM. The crystal structure and phase composition of the films were studied by x-ray diffraction （XRD）. Several parameters such as the discharge power, the ratio of carrier gas to the precursor gas, the deposition time on the crystallization behavior, the deposition rate and the surface morphology of the titania film were extensively studied.

Spectroscopic Study of a Radio-Frequency Atmospheric Pressure Dielectric Barrier Discharge with Anodic Alumina as the Dielectric

This paper presents the fabrication and a spectroscopic study of a stable radio- frequency dielectric barrier discharge （RF DBD） in Ar with a novel dielectric, anodic alumina, at atmospheric pressure. Dielectric electrodes are fabricated from commercially available low cost impure aluminum strips by a two-step anodization process in 0.3 M solution of oxalic acid. The discharge is found to be stable with excellent spatial uniformity for the RF input power range of 30～80 W. Excitation and rotational temperatures measured in the experiment range of 1472～3255 K and 434～484 K, respectively, as the input power changes from 30 W to 80 W. These temperature ranges are suitable for surface modification applications.

Atmospheric Pressure Radio Frequency Dielectric Barrier Discharges in Nitrogen/Argon

This work reports the experimental results on the characteristics of radio frequency dielectric barrier N2/Ar discharges. Depending on the nitrogen content in the feed gas and the input power, the discharge can operate in two different modes： a homogeneous glow discharge and a constricted discharge. With increasing input power, the number of discharge columns increases. The discharge columns have starlike structures and exhibit symmetric self-organized arrangement. Optical emission spectroscopy was performed to estimate the plasma temperature. Spatially resolved gas temperature measurements, determined from NO emission rotational spectroscopy were taken across the 4.4 mm gap filled by the discharge. Gas temperature in the middle of the gas gap is lower than that close to the electrodes.

Transition of Streamer, Corona and Glow Discharges in Needle-to-plane Dielectric Barrier Discharge at Atmospheric Pressure Air

To discuss the modes of dielectric barrier discharge(DBD) between needle-to-plane electrodes in air,DBD is generated and observed on a needle-to-plane device at atmospheric pressure air.Fast images of the DBD are taken by using a charge couple device(CCD) cinema with a macro lens,while the electrical and photo-electricity waveforms of the DBD are recorded.The current waveforms show that under an applied voltage of 3 kV,there are numerous short current pulses in both positive and negative half-periods of discharges.However,under 6 kV,there are still the numerous short current pulses in the positive half-periods,but only one wide current pulse in each negative half-period.This difference is also found in the photoelectric signals.The streamer,corona and glow discharges are observed from the images of the discharges at different applied voltages.The structure of glow discharge in the negative period is exactly the same as that of the low pressure glow discharge.However,in the positive period of discharge there is always a streamer.In the negative period of discharge,while the applied voltage increases,the transition from corona to glow discharge is observed.The progress of a transition between streamer and glow discharge at 6 kV during one period is analyzed.The glow discharge appearance is determined by two factors: the discharge current is limited to a certain extent by the dielectric layer; the charges deposited on the dielectric layer during the last half period enhance the intensity of the electric field.At an insufficient applied voltage,the cathode drop leads to no glow discharge,but Trichel pulses.

Simulation of transition from Townsend mode to glow discharge mode in a helium dielectric barrier discharge at atmospheric pressure

The dielectric barrier discharge characteristics in helium at atmospheric pressure are simulated based on a one- dimensional fluid model. Under some discharge conditions, the results show that one discharge pulse per half voltage cycle usually appears when the amplitude of external voltage is low, while a glow-like discharge occurs at high voltage. For the one discharge pulse per half voltage cycle, the maximum of electron density appears near the anode at the beginning of the discharge, which corresponds to a Townsend discharge mode. The maxima of the electron density and the intensity of electric field appear in the vicinity of the cathode when the discharge current increases to some extent, which indicates the formation of a cathode-fall region. Therefore, the discharge has a transition from the Townsend mode to the glow discharge mode during one discharge pulse, which is consistent with previous experimental results.

Preparation of Copper Nanoparticles Using Dielectric Barrier Discharge at Atmospheric Pressure and its Mechanism

Dielectric barrier discharge （DBD） cold plasma at atmospheric pressure was used for preparation of copper nanoparticles by reduction of copper oxide （CuO）. Power X-ray diffraction （XRD） was used to characterize the structure of the copper oxide samples treated by DBD plasma. Influences of H2 content and the treating time on the reduction of copper oxide by DBD plasma were investigated. The results show that the reduction ratio of copper oxide was increased initially and then decreased with increasing H2 content, and the highest reduction ratio was achieved at 20% H2 content. Moreover, the copper oxide samples were gradually reduced by DBD plasma into copper nanoparticles with the increase in treating time. However, the average reduction rate was decreased as a result of the diffusion of the active hydrogen species. Optical emission spectra （OES） were observed during the reduction of the copper oxide samples by DBD plasma, and the reduction mechanism was explored accordingly. Instead of high-energy electrons, atomic hydrogen （H） radicals, and the heating effect, excited-state hydrogen molecules are suspected to be one kind of important reducing agents. Atmospheric-pressure DBD cold plasma is proved to be an efficient method for preparing copper nanoparticles.

Numerical study on the discharge characteristics and nonlinear behaviors of atmospheric pressure coaxial electrode dielectric barrier discharges

The discharge characteristics and temporal nonlinear behaviors of the atmospheric pressure coaxial electrode dielectric barrier discharges are studied by using a one-dimensional fluid model. It is shown that the discharge is always asymmetrical between the positive pulses and negative pulses. The gas gap severely affects this asymmetry. But it is hard to acquire a symmetrical discharge by changing the gas gap. This asymmetry is proportional to the asymmetric extent of electrode structure, namely the ratio of the outer electrode radius to the inner electrode radius. When this ratio is close to unity, a symmetrical discharge can be obtained. With the increase of frequency, the discharge can exhibit a series of nonlinear behaviors such as period-doubling bifurcation, secondary bifurcation and chaotic phenomena. In the period-doubling bifurcation sequence the period-n discharge becomes more and more unstable with the increase of n. The period-doubling bifurcation can also be obtained by altering the discharge gas gap. The mechanisms of two bifurcations are further studied.It is found that the residual quasineutral plasma from the previous discharges and corresponding electric field distribution can weaken the subsequent discharge, and leads to the occurrence of bifurcation.

Characteristic of Atmospheric Pressure Plasma Jet in Coplanar Dielectric Barrier Discharge

Non-thermal plasma jet at atmospheric pressure has recently attracted lots of attention because of its applications in plasma bullet or plasma plume.Thus,we studied on generating plasma jet by coplanar dielectric barrier discharge in a device driven by sinusoidal voltage.The processes of plasma discharges in both positive and negative half cycles were recorded using a high-speed ICCD(intensified charge-coupled device)camera;based on the results we estimated the velocity of plasma propagation,and investigated the influence of gas flow on the plasma development.It is shown that the plasma bullets,which have velocity in the order of 103～104m/s,exist only outside the cathode.APPJ(atmospheric pressure plasma jet)is created by the electron beam from the cathode,and then sustained by a strong radial electric field near and outside the cathode.The gas flow influences the APPJ length in air but not the APPJ discharge,while the discharge is affected significantly by the applied voltage.

Two-Dimensional Simulation of Spatial-Temporal Behaviors About Period Doubling Bifurcation in an Atmospheric-Pressure Dielectric Barrier Discharge

As a spatially extended dissipated system, atmospheric-pressure dielectric barrier discharges （DBDs） could in principle possess complex nonlinear behaviors. In order to improve the stability and uniformity of atmospheric-pressure dielectric barrier discharges, studies on tem- poral behaviors and radial structure of discharges with strong nonlinear behaviors under different controlling parameters are much desirable. In this paper, a two-dimensional fluid model is devel- oped to simulate the radial discharge structure of period-doubling bifurcation, chaos, and inverse period-doubling bifurcation in an atmospheric-pressure DBD. The results show that the period-2n （n = 1, 2... ） and chaotic discharges exhibit nonuniform discharge structure. In period-2n or chaos, not only the shape of current pulses doesn＇t remains exactly the same from one cycle to an- other, but also the radial structures, such as discharge spatial evolution process and the strongest breakdown region, are different in each neighboring discharge event. Current-voltage characteris- tics of the discharge system are studied for further understanding of the radial structure.

Effect of Duty Cycle on the Characteristics of Pulse-Modulhted Radio-Frequency Atmospheric Pressure Dielectric Barrier Discharge

Using a one-dimensional fluid model, the pulse-modulated radio-frequency dielectric barrier discharge in atmospheric helium is described. The influences of the pulse duty cycle on the discharge characteristics are studied. The numerical results show that the dependence of discharge characteristics on the duty cycle is sensitive in the region of around 40% duty cycle under the given simulation parameters. In the case of a larger duty cycle, the plasma density is higher, the discharge becomes more intense, but the power consumption is higher. When the duty cycle is lower, one can get a weaker discharge, lower plasma density and higher electron temperature in the bulk plasma. In practical applications, in order to get a higher plasma density and a lower power consumption, it is more important to choose a suitable duty cycle to modulate the RF power supply.

Numerical studies of atmospheric pressure glow discharge controlled by a dielectric barrier between two coaxial electrodes

The glow discharge in pure helium at atmospheric pressure, controlled by a dielectric barrier between coaxial electrodes, is investigated based on a one-dimensional self-consistent fluid model. By solving the continuity equations for electrons, ions, and excited atoms, with the current conservation equation and the electric field profile, the time evolution of the discharge current, gas voltage and the surface density of charged particles on the dielectric barrier are calculated. The simulation results show that the peak values of the discharge current, gas voltage and electric field in the first half period are asymmetric to the second half. When the current reaches its positive or negative maximum, the electric field profile, and the electron and ion densities represent similar properties to the typical glow discharge at low pressures. Obviously there exist a cathode fall, a negative glow region, and a positive column. Effects of the barrier position in between the two coaxial electrodes and the discharge gap width on discharge current characteristics are also analysed. The result indicates that, in the case when the dielectric covering the outer electrode only, the gas is punctured earlier during the former half period and later during the latter half period than other cases, also the current peak value is higher, and the difference of pulse width between the two half periods is more obvious. On reducing the gap width, the multiple current pulse discharge happens.

Electrical features of radio-frequency atmospheric pressure helium discharge with and without dielectric electrodes

A comparative study of radio-frequency atmospheric pressure glow discharge(rf APGD)generated in helium with and without dielectric electrodes to investigate the effect of electrodes insulation on electrical features of APGD is presented. In the α mode, both the rf APGDs remain volumetric, stable and uniform. In the γ mode, the APGD without dielectric electrodes shrinks into a constricted plasma column whereas APGD with dielectric electrodes remains stable and retains the same volume without plasma constriction even at higher densities of discharge current. A comparison of electrical features of both rf APGDs in normal and abnormal glow discharge regimes is presented. In both APGDs with and without dielectric electrodes,impedance measurements have been performed and compared with equivalent circuit models.The measured impedance data is found to be in good agreement with simulated data.

The Role of Metastable Atoms in a Homogeneous Atmospheric Pressure Barrier Discharge in Helium

A one-dimensional fluid model for homogeneous atmospheric pressure barrier discharges in helium is presented by considering elementary processes of excitation and ionization including a metastable atom effect. Using this model we investigate the behaviours of the helium metastable atoms in discharges as well as their influence on the discharge characteristics. It is shown that the metastable atoms with a relatively high concentration during the discharge are mainly produced in the active phase of the discharge and dissolved in the off phase. It is also found that the metastable atom collisions can not only provide seed electrons for discharges but also influence the concentration of ions. A reduction of matestable atom density results in a drop in the charged particle densities and causes a qualitative change in the discharge patterns.

Effects of the transverse electric field on nanosecond pulsed dielectric barrier discharge in atmospheric airflow

In this paper,an asymmetric electrode geometry(the misalignment between the ends of highvoltage and grounded electrodes)is proposed in order to investigate the effects of the transverse electric field on nanosecond pulsed dielectric barrier discharge(DBD).The results show that diffuse discharge manifests in the misaligned region and the micro-discharge channel in the aligned region moves directionally.Moreover,the diffuse discharge area increases with the decrease of the discharge gap and pulse repetition frequency,which is consistent with the variation of the moving velocity of the micro-discharge channel.When airflow is introduced into the discharge gap in the same direction as the transverse electric field,the dense filamentary discharge region at the airflow inlet of asymmetric electrode geometry is larger than that of symmetric electrode geometry.However,when the direction of the airflow is opposite to that of the transverse electric field,the dense filamentary discharge region of asymmetric electrode geometry is reduced.The above phenomena are mainly attributed to the redistribution of the space charges induced by the transverse electric field.

A Computational Study on the Discharge Characteristics of Atmospheric Dielectric Barrier Discharges at a Constant Power

The study on homogeneous DBDs at atmospheric pressure has attracted much attention for their advantages in applications. Tremendous work has been conducted both experimentally and numerically at a constant applied voltage or driving frequency. However the investigation of dielectric barrier discharges is still scarce for a constant power or power density. In this work, a new computational approach for DBDs is developed to explore atmospheric DBDs at a constant power based on a one-dimensional fluid model. The frequency and gap spacing effects on the atmospheric plasmas are systematically analyzed based on computational data. The computational results show that at a constant power both the current density and the amplitude of the applied voltage decrease, whereas the current pulse width increases, with increasing frequency. The simulation also indicates that as the gap spacing is raised with a fixed power and frequency, the current density and electron density increase initially, then reach their peak values, and then decrease, which means that there are maximum values for both of them. These results are significant for many industrial applications, as they can be used to optimize plasma devices of DBDs with the consideration of power consumption.