Simulation of Droplet-gas Flow in the Effervescent Atomization Spray with an Impinging Plate

Abstract A comprehensive three-dimensional model of droplet-gas flow was presented to study the evolution of spray in the effervescent atomization spray with an impinging plate. For gas phase, the N-S equation with the κ-ε turbulence model was solved, considering two-way coupling interaction between droplets and gas phase. Dispersed droplet phase is modeled as Lagrangian entities, accounting for the physics of droplet generation from primary and secondary breakup, droplet collision and coalescence, droplet momentum and heat transfer. The mean size and sta- tistical distribution of atomized droplets at various nozzle-to-plate distances were calculated. Some simulation resuits were compared well with experimental data. The results show that the existence of the impinging plate has a pronounced influence on the droplet mean size, size distribution and the droplet spatial distribution. The air-to-liquid ratio has obvious effects on the droplet size and distribution.

Coordination of distinctive pesticide adjuvants and atomization nozzles on droplet spectrum evolution for spatial drift reduction

Pesticide adjuvants,as crop protection products,have been widely used to reduce drift loss and improve utilization efficiency by regulating droplet spectrum.However,the coordinated regulation mechanisms of adjuvants and nozzles on droplet spectrum remain unclear.Here,we established the relationship between droplet spectrum evolution and liquid atomization by investigating the typical characteristics of droplet diameter distribution near the nozzle.Based on this,the regulation mechanisms of distinctive pesticide adjuvants on droplet spectrum were clarified,and the corresponding drift reduction performances were quantitively evaluated by wind tunnel experiments.It shows that the droplet diameter firstly shifts to the smaller due to the liquid sheet breakup and then prefers to increase caused by droplet interactions.Reducing the surface tension of sprayed liquid facilitates the uniform liquid breakup and increasing the viscosity inhibits the liquid deformation,which prolong the atomization process and effectively improve the droplet spectrum.As a result,the drift losses of flat-fan and hollow cone nozzles are reduced by about 50%after adding organosilicon and vegetable oil adjuvants.By contrast,the air induction nozzle shows a superior anti-drift ability,regardless of distinctive adjuvants.Our findings provide insights into rational adjuvant design and nozzle selection in the field application.

AgNi15 composite particles prepared by ultrasonic arc spray atomization method

Ultrasonic arc spray atomization (UASA) method was used to prepare high-melting-point, immiscible AgNi15 (mass fraction, %) composite particles. Sieving was used to determine the size distribution of the AgNi15 particles. The morphology, rapidly solidified structure and metastable solution expansion of the AgNi15 particles were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS), respectively. The results show that the AgNi15 composite particles are spherical and well-dispersed, and the mass fractions of the particles with diameters <74μm and <55 μm are 99.5% and 98%, respectively. The rapidly solidified structure of the AgNi15 particles consists of spherical nickel-richβ(Ni)-phase particles dispersed throughout a silver-richα(Ag)-phase matrix andα(Ag)-phase nanoparticles dispersed throughout largerβ(Ni)-phase particles. The silver and nickel in the AgNi15 particles form a reciprocally extended metastable solution, and the solid solubility of nickel in the silver matrix at room temperature is in the range of 0.16%?0.36% (mole fraction).

Analysis of Solidification in Spray Atomized and Codeposited Metal-matrix Composites Part Ⅰ: Atomization

Fluid mechanics, heat transfer and liquid-to-solid phase transformation are assessed in optimizing the spray atomization and codeposition process parameters for size refinement and microstructural uniformity of the deposited material. Atomization gas velocities, atomized droplets velocities, convective heat transfer coefficients, thermal histories of the solidifying droplets, freezing rates, fraction solid evolution and solid-liquid interface propagation velocity are calculated. The influence, on the deposit microstructural features, of process parameters like the atomization gas pressure, the pouring tube orifice diameter, the geometrical features of the atomization device,the potency of , pre-existing or injected as reinforcement, nucleation sites, the wetting angle between the liquid melt bnd impurity particles acting as preferred nucleation sites, the in-flight distance of the solidifying droplets in the atomization chamber, i5 evaluated. As a result of the evaluation, appropriate choice of the adjustable process parameters for the production of powders and/or deposits with desired grain size and microstructure, can be made.

Resonant behaviors of ultra-sonic gas atomization nozzle with zero mass-flux jet actuator

The resonant behaviors of an ultra-sonic gas atomization nozzle with a zero mass-flux jet actuator were numerically investigated with FLUENT software by using a double precision unsteady two-dimensional pressure-based solver. The Spalart-Allmaras turbulence model was adopted in the simulations. Numerical results indicated that the oscillation properties of the gas efflux were effectively improved. Several resonatory frequencies corresponding to different vibration modes of gas were distinguished in the nozzle. With the changing of nozzle geometric parameters, different characters among those modes were elucidated by analyzing the propagations of pressure waves.

Effects of atomization parameters of dust removal nozzles on the de-dusting results for different dust sources

In order to obtain appropriate spray pressure and enhance the spraying and dust removal efficiency, various factors including the dust characteristics, nozzle spraying angle, effective spraying range, water consumption and droplet size are taken into account. The dust characteristics from different mines and atomization parameters of different pressure nozzles were measured. It was found that the internal pressure of coal cutters and roadheaders should be kept at 2 MPa, which could ensure large droplet size, large spraying angle and low water consumption and hence realizing a large-area covering and capture for large particle dusts. However, the external spray pressure should be kept at 4 MPa for smaller droplet size and longer effective spraying range, leading to effective dust removal in the operator zone. The spray pressure of support moving, drawing opening, and stage loader on a fully mechanized caving face and stage loader on a fully mechanized driving face should be kept at 8 MPa, under which the nozzles have long effective spraying range, high water flow and small droplet size for the rapid capture of instantaneous, high-concentration and small size dust groups. From the applications on the caving and driving faces in the coal mines, it is indicated that the optimization of spray pressure in different spraying positions could effectively enhance dust removal efficiency. Selecting appropriate nozzles according to the dust characteristics at different positions is also favorable for dust removal efficiency. With the selected nozzles under optimal pressures, the removal rates of both total dust and respirable dust could reach over70%, showing a significant de-dusting effect.

Numerical calculation of temperature and phase change during the process of atomizing spray quenching on drilling pipe

A finite element method (FEM) procedure was developed in order to simulatethe quenching process for drilling pipe (DP). The calculating model was based ontime-temperature-transformation (TTT) diagrams, and incorporated with material properties dependenton temperature. The procedure was used to calculate the temperature-time histories, describe thephase transformations of atomizing spray quenching for DP in the welding zone, and predict thehardness distribution in radius direction after quenching in the zone. The calculated results metwell with that of experiments. It was easy to determine the parameters such as volume and pressureof the cooling water and compressed gas by use of the numerical calculation and experiments, becausethe value of convection coefficient was decided greatly by the mixture of the cooling water andcompressed gas. Moreover, the simulating results were helpful not only to design the quenchingequipment, but also to optimize the quenching process for DP's welding zone.

Spray Atomized and Codeposited Al-Li Based Metal-matrix Composites Processing and Properties

In spray atomization and codeposition, a molten stream of metal is disintegrated into a fine dispersion of droplets by high velocity gas jets. The resulting semi-solidified droplets are directed towards a substrate where they impact and collect as rapidly solidified splats. Relatively high rates of solidification are achieved as a result of the thinness of the splats and the rapid heat extraction during flight and upon impacting with the substrate. The processing method uses codeposition of the metallic semi-solidified droplets (metallic matrix) with the injected reinforcement ceramic particles. In the present paper, the microstructures, mechanical properties, interfacial properties, thermal stability and aging behaviour of spray atomized and codeposited Al-Li-X MMC's (injected X=SiC, Al2O3) are reported and correlated to the processing conditions.

Analysis of Solidification in Spray Atomized and Codeposited Metal-matrix Composites Part Ⅱ:Reinforcement Injection and Deposition

The influence of the injection of reinforcing particles (for the production of metal matrix composites and of the droplets-to-substrate heat transfer on the resulting microstructural uniformity of spray atomized and codeposited composite material is analyzed. The reinforcement particles injection velocity has to be limited between an upper and a lower critical values. in order to ensure entrapment into the matrix droplets in flight. The thermal history of the injected droplets during the deposition stage is calculated with the assumption that the in-flight solidifying droplets reach the substrate while containing still at least 20% liquid volume fraction, in order to avoid porosity of the deposited material. The substrate to pouring-tube orifice distance where that condition is achieved depends strongly on the atomization pressure and the convective heat transfer coefficient of the substrate. It is demonstrated that 'tailoring' the microstructures and the reinforcement volume percent in the deposited material is feasible. The critical process parameters : the atomization pressure, the melt flow rate. the substrate to pouring-tube orifice distance, the reinforcement particles injection location and rate can all be adequately chosen in order to obtain any desired microstructure, grain size, reinforcement volume percent, with the additional benefit, if wanted, of rapid solidification processing

SPRAY FORMED NICKEL-BASE SUPERALLOYS

In this paper,part of the research and development work in the field of spray formed superalloys at BIAM of China is briefly summarized. With an experimental spray forming facility,whose melting capacity is suitable for making disk and columnar shaped integral-dense and clean Ni-base superalloy preforms with low oxygen content,fine grain, uniform chemistry and improved forgeability, a series of Ni-base superalloys have been spray atomized and deposited, among which three alloys have been chosen for microstructural and mechanical properties evaluation.

Microstructure of a Spray Deposited Intermetallic Compound Alloy of Ni-Al-Mo System

The microstructure of a spray deposited intermetallic compound alloy of Ni-Al-Mo system（Ni3Al-Mo intermetallic compound alloy） prepared by a spray atomization deposition was studied in detail by using optical metallography,XRD,DTA,SEM,TEM,HREM and computer simulation.The preform consists of uniform and equiaxial grains,ranging from 10-40 μm,with some microporosity.Besides the main phases of the matrix alloy γ＇ and γ,Ni2Mo and Ni3Mo phases are also found within the γ network.A new Ni enriched phase in the γ phase was identified to have face-centered cubic structure with a lattice constant α=1.09 nm and space group Fm3m.

Dynamic evolution of low-viscosity fuel particle distribution driven by constant flow

The effects of mass concentration and injection pressure on the atomization characteristics of low-viscosity fuel spray are studied in a constant-volume chamber.Microscopic spray parameters are measured by laser diffraction at different axial and radial positions downstream of the nozzle.The results show that the atomization effect is inhibited linearly with the increase of mass concentration.The increase of injection pressure promotes the droplet breakup.However,the trend gradually weakens and becomes more noticeable at high concentrations.Comparing with the concentration,the influence of the injection pressure on the atomization characteristics is dominant.Although low concentration and high injection pressure can promote the droplet breakup,they also increase the probability of droplet collision,resulting in droplet aggregation.This is more evident in low-viscosity fuels.The droplet size increases in the axial direction owing to the aggregation.However,the diameter decreases in the radial direction owing to the outward deflection of small droplets caused by air turbulence and entrainment.In addition,the high-velocity airflow significantly promotes the droplet breakup near the nozzle and spray axis regions and inhibits the aggregation effect.However,the lower-viscosity fuels keep smaller droplet sizes and better atomization in the whole spraying process,which is easier to realize than the higher-viscosity fuels.Overall,low concentration,high injection pressure,and low viscosity of fuel have beneficial effects on the droplet breakup.This is very important for improving the atomization effect of fuel.

Numerical simulation of flow in Hartmann resonance tube and flow in ultrasonic gas atomizer

The gas flow in the Hartmann resonance tube is numerically investigated by the finite volume method based on the Roe solver. The oscillation of the flow is studied with the presence of a needle actuator set along the nozzle axis. Numerical results agree well with the theoretical and experimental results available. Numerical results indicate that the resonance mode of the resonance tube will switch by means of removing or adding the actuator. The gas flow in the ultrasonic gas atomization （USGA） nozzle is also studied by the same numerical methods. Oscillation caused by the Hartmann resonance tube structure, coupled with a secondary resonator, in the USGA nozzle is investigated. Effects of the variation of parameters on the oscillation are studied. The mechanism of the transition of subsonic flow to supersonic flow in the USGA nozzle is also discussed based on numerical results.

Properties of acoustic resonance in double-actuator ultra-sonic gas nozzle:numerical study

The ultra-sonic gas atomization （USGA） nozzle is an important apparatus in the metal liquid air-blast atomization process. It can generate oscillating supersonic gas effiux, which is proved to be effective to enforce the atomization and produce narrow-band particle distributions. A double-actuator ultra-sonic gas nozzle is proposed in the present paper by joining up two active signals at the ends of the resonance tubes. Numerical sim- ulations axe adopted to study the effects of the flow development on the acoustic resonant properties inside the Haxtmann resonance cavity with/without actuators. Comparisons show that the strength and the onset process of oscillation are enhanced remarkably with the actuators. The multiple oscillating amplitude peaks are found on the response curves, and two kinds of typical behaviors, i.e., the Hartmann mode and the global mode, are discussed for the corresponding frequencies. The results for two driving actuators are also investigated. When the amplitudes, the frequencies, or the phase difference of the input signals of the actuators are changed, the oscillating amplitudes of gas effiux can be altered effectively.

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF PARTICULATE REINFORCED MATRIX COMPOSITE

TiB2 - particulate- reinforced Ni3 Al composites were prepared by spray a tom-ization co-deposition technique. The reinforcement particulate can be uniformly distributedin matrix alloy, and no interaction would be found at interface between TiB, and Ni,Al.In a word, the composites possess comprehensive mechanical properties.

Modeling on effervescent atomization:A review

The study and modeling process of effervescent atomization are reviewed. The mechanism of droplet events and the treatment of liquid fragmentation process and dispersed particles are systematically presented, which includes the primary atomization of Newtonian and non-Newtonian fluid, instability analysis, turbulence treatment, particle tracking, secondary atomization and droplets collision. The review on the sub-models involved in the simulation of effervescence is followed by a summary of the achievements of modeling. First is the validation of models; then the parametric study is summarized; the third part introduces the fitting formula of droplet mean size and impinging factors, and finally the scope of future study is indicated.

Analysis of pneumatic atomizer spray profiles

Our objective is to analyze the atomization processes of a pneumatic atomizer by measuring the size and velocity distributions of droplets in a liquid paint spray. The droplet size and velocity distributions have been determined at different axial positions in the spray; a mathematical description of how these quan- tities vary throughout the spray is then proposed. Additionally, the relative number density of droplets and the relative local mass flux are estimated.