Evolution of Biofilm and Its Effect on Microstructure of Mortar Surfaces in Simulated Seawater

To explore the role of biofilm formation on the corrosion of marine concrete structures, we investigated the attachment of biofilm on mortar surfaces in simulated seawater and the influence of biofilm on the microstructure of mortar surfaces. The results show that the evolution of biofilm on mortar surfaces in simulated seawater is closely related to the corrosion suffered by the mortar, and the process of biofilm attachment and shedding is continuous and cyclical. It is found that the specimens in the absence of biofilm attachment are more severely eroded internally by the corrosive medium in simulated seawater than those in the presence of biofilm attachment. For the specimens without biofilm attachment, after 60 days, gypsum forms,and after 120 days, the number of pores in the mortar is reduced. In contrast, for the specimens in the presence of biofilm attachment, gypsum could only be detected after 90 days, and fewer pores are filled. Therefore, the formation of biofilm could delay the invasion of the corrosive medium into the interior of mortar during the evolution of biofilm on mortar surfaces, mitigating the corrosion of mortars in seawater.

Performances of biological aerated filter employing hollow fiber membrane segments of surface-improved poly(sulfone) as biofilm carriers

Using the surface of poly （sulfone） hollow fiber membrane segments as grafted layer, the hydrophilic acrylamide chain was grafted on by UV-photoinduced grafting polymerization. The gained improvement of surface wettability for the modified membrane was tested by measuring the contact-angle as well as FTIR spectra. Then correlation between the hydrophilic ability of support material and the biofilm adherence ability was demonstrated by comparing the pollutant removal rates from urban wastewater via two identical lab-scale up-flow biological aerated filters, one employed the surface wettability modified poly （sulfone） hollow fiber membrane segment as biofilm carder and the other employed unmodified membrane segment as biofilm carder. The experimental results showed that under the conditions of influent flux 5 L/h, hydraulic retention time 9 h and gas to liquid ratio （G/L） 10： 1, the removal rates of chemical oxygen demand （COD） and ammonium nitrogen （NH4^＋-N） for the modified packing filter and the unmodified packing filter was averaged at 83.64% and 96.25%, respectively, with the former filter being 5%-20% more than the latter. The effluent concentration of COD, NH4^＋-N and turbidity for the modified packing filter was 25.25 mg/L, 2 mg/L and 8 NTU, respectively. Moreover, the ammonium nitrogen removal performance of the filter packing the modified PSF was compared with the other bioreactor packing of an efficient floating medium. The biomass test indicated that the modified membrane matrixes provided better specific adhesion （3310-5653 mg TSS/L support）, which gave a mean of 1000 mg TSS/L more than the unmodified membrane did. In addition, the phenomenon of simultaneous denitrification on the inner surface of the support and nitrification on the outer surface was found in this work.

Comparison of air-borne xylene biodegradation between immobilizedcell biofilter and biofilm attached biofilter

The Bacillus firmus was immobilized into Ca-alginate beads according to the different initial biomass concentration, calcification time and activation time. Three types of immobilized Bacillus firmus beads were packed respectively in trickling biofilter to purify xylene contained waste gases, and the performance of immobilized-cell biofilter was compared with traditional biofilm attached biofilter packed with two types of ceramic pellets. The results showed that three types of immobilized beads had different capabilities for removing xylene and life-spans. Higher initial biomass in immobilized beads resulted in better performance but shorter life-span. Activation process can remarkably enhance the activity of bacteria, and the removal efficiency of xylene can substantially be improved. Calcification time had influence on life-span of immobilized beads. Without acclimation, the cell-entrapped biofilter can obtain the maximum elimination capacity of 92.4 g/（m^3·h）. However, compared with biofilm attached biofilter, it has a poorer intrinsic drawback in volatile organic compounds （VOCs） removal due to the existence of excess mass transfer resistance.

A novel protein-repellent dental composite containing 2-methacryloyloxyethyl phosphorylcholine

Secondary caries due to biofilm acids is a primary cause of dental composite restoration failure.To date,there have been no reports of dental composites that can repel protein adsorption and inhibit bacteria attachment.The objectives of this study were to develop a protein-repellent dental composite by incorporating 2-methacryloyloxyethyl phosphorylcholine（MPC） and to investigate for the first time the effects of MPC mass fraction on protein adsorption,bacteria attachment,biofilm growth,and mechanical properties.Composites were synthesized with 0（control）,0.75%,1.5%,2.25%,3%,4.5%and 6%of MPC by mass.A commercial composite was also tested as a control.Mechanical properties were measured in three-point flexure.Protein adsorption onto the composite was determined by the microbicinchoninic acid method.A human saliva microcosm biofilm model was used.Early attachment at 4 h,biofilm at 2 days,live/dead staining and colony-forming units（CFUs） of biofilms grown on the composites were investigated.Composites with MPC of up to 3%had mechanical properties similar to those without MPC and those of the commercial control,whereas 4.5%and 6%MPC decreased the mechanical properties（P〈0.05）.Increasing MPC from 0 to 3%reduced the protein adsorption on composites（P〈0.05）.The composite with 3%MPC had protein adsorption that was 1/12 that of the control（P〈0.05）.Oral bacteria early attachment and biofilm growth were also greatly reduced on the composite with 3%MPC,compared to the control（P〈0.05）.In conclusion,incorporation of MPC into composites at 3%greatly reduced protein adsorption,bacteria attachment and biofilm CFUs,without compromising mechanical properties.Protein-repellent composites could help to repel bacteria attachment and plaque build-up to reduce secondary caries.The protein-repellent method might be applicable to other dental materials.

Opinion on the recent development of environmentally friendly marine anti-fouling coating

Marine biofouling is a global problem that is detrimental to both moving ships and static underwater devices.Marine microorganisms tend to attach to any unprotected surface and grow into biofilm,which can be hardly removed even under high shear flow condition[1].With the long-term accumulation of marine organisms,ships suffer significantly from the increase on the net weight as well as the drag when cruising.Increased drag causes fuel power penalties of up to86%at cruising speed;it is notable even a very thin layer