Nickel-based superalloy architectures with surface mechanical attrition treatment: Compressive properties and collapse behaviour

Surface modifications can introduce natural gradients or structural hierarchy into human-made microlattices,making them simultaneously strong and tough.Herein,we describe our investigations of the mechanical properties and the underlying mechanisms of additively manufactured nickel–chromium superalloy(IN625)microlattices after surface mechanical attrition treatment(SMAT).Our results demonstrated that SMAT increased the yielding strength of these microlattices by more than 64.71%and also triggered a transition in their mechanical behaviour.Two primary failure modes were distinguished:weak global deformation,and layer-by-layer collapse,with the latter enhanced by SMAT.The significantly improved mechanical performance was attributable to the ultrafine and hard graded-nanograin layer induced by SMAT,which effectively leveraged the material and structural effects.These results were further validated by finite element analysis.This work provides insight into collapse behaviour and should facilitate the design of ultralight yet buckling-resistant cellular materials.

Effect of mechanical attrition on microstructure and property of electroplated Ni coating

Ni coating was deposited on carbon steel by a mechanical attrition enhanced electroplating （MAEE） process. During the electroplating, the mechanical attrition（MA） was introduced by impact of glass balls on the sample surface with a special vibrating frequency. The surface and cross-sectional images of Ni coating were observed with SEM. The microstructure and crystallinity of coating were examined with TEM and XRD. The electrochemical performance of coating was measured with polarization curves and electrochemical impedance spectroscopy （EIS） and its mechanical behaviours, such as tensile strength and hardness, were studied. The results show that the MA has significant effects on the microstructure and property of the electroplated Ni coating. By MA, the coating becomes smooth, compact, thin and has refined grains and is free of cracks and pores. Consequently, the adhesion, tensile strength, hardness and corrosion resistance of coating are improved significantly.

Improved Fatigue Behavior of Pipeline Steel Welded Joint by Surface Mechanical Attrition Treatment(SMAT)

A pipeline steel X80 with welded joint was subjected to surface mechanical attrition treatment （SMAT）. After SMAT, a nanostructure surface layer with an average grain size of about 10 nm was formed in the treated sample, and the fatigue limit of the welded joint was elevated by about 13% relative to the untreated joints. In the low and the high amplitude stress regimes, both fatigue strength and fatigue life were enhanced. Formation of the nanostructured surface layer played more important role in the enhanced fatigue behavior than that of residual stress induced by the SMAT.

Study on the friction and wear properties of the surface nanocrystallized 1.0C-1.5Cr steel induced by the surface mechanical attrition treatment

Nano-structured layers are fabricated on the surface of 1.0C-1.5Cr steel by using the surface mechanical attrition treatment(SMAT)technology,and the microstructures of the surface nano-crystallization layers are characterized by means of X-ray diffraction(XRD)and transmission electron microscopy(TEM).The friction and wear properties are also investigated by a UMT-2 friction and wear tester.Experimental research has indicated that the average diameter of nanocrystalline grains in the surface layer after being treated for 15 min is in the range of 10-20 nm,and ferrite and cementite grains can not be identified by their morphologies.The wear-resistance of the specimen treated for 15 min has been doubled,compared with that of the matrix due to the grain refinement to a nano-sized scale.The lowest friction coefficient is 0.27,which is for the specimen treated for 30 min,resulting from the dissolution of the cementite phase and the formation of a relative homogenous structure.The SMAT technique for enhancing the wear-resistance of the 1.0C-1.5Cr steel has an optimum processing time,which is in the range of 15-30 min.The dominant wear mechanism of the specimen treated for 15 min changes from adhesive wear into particle wear.

Aluminizing Low Carbon Steel at Lower Temperatures

This study reports the significantly enhanced aluminizing behaviors of a low carbon steel at temperatures far below the austenitizing temperature, with a nanostructured surface layer produced by surface mechanical attrition treatment （SMAT）. A much thicker iron aluminide compound layer with a much enhanced growth kinetics of η-Fe2Al5 in the SMAT sample has been observed relative to the coarse-grained steel sample. Compared to the coarse-grained sample, a weakened texture is formed in the aluminide layer in the SMAT sample. The aluminizing kinetics is analyzed in terms of promoted difusivity and nucleation frequency in the nanostructured surface layer.

EFFECT OF NANOCRYSTALLINE AND TWIN BOUNDARIES ON CORROSION BEHAVIOR OF 316L STAINLESS STEEL USING SMAT

By means of surface mechanical attrition treatment （ SMAT）, the groin size with a diameter of aboat 60hm formed at about 20μm depth and numerous mechanical twins at about 50μm depth from the treated surface were synthesized in 316L stainless steel because of the different distributions of strain and strain rate along depth orientation. For instance the maximum strain rate reached 10^3-10^4s^-1 on the top surface. The relationship between the microsturcture and the corrosion property was studied in 0.05M H2SO4＋ 0.25M Na2SO4 aqueous solution, and the results show an extreme improvement of corrosion resistance owing to the appearance of twin boundaries and the obvious reduction in corrosion resistance attributed to the presence of nanocrystaline boundaries.

Tensile Properties of Cu with Deformation Twins Induced by SMAT

High density nano-scale deformation twins were introduced in the surface layer of Cu sample by means of surface mechanical attrition treatment （SMAT） at room temperature. The Cu sample with deformation twins shows a yield strength of about 470 MPa in tension tests. The significant strengthening may be attributed to the effective inhibition of slip dislocations by abundant twin boundaries.

Influence of Surface Nano-structured Treatment on Pack Boriding of H13 Steel

In order to lower the boriding temperature of hot work steel H13, method of surface mechanical attrition treatment （SMAT）, which can make the grain size of the surface reach nano-scale, was used before pack boriding. The growth of the boride layer was studied in a function of boriding temperature and time. By TEM （transmission electron microscopy）, SEM （scanning electron microscopy）, XRD （x-ray diffraction） and microhardness tests, the grain size, thermal stability of the nano-structured （NS） surface and the thickness,appearance, phases of the surface boride layer were studied. Kinetic of boriding was compared between untreated samples and treated samples. Results showed that after SMAT, the boride layer was thicker and the hardness gradient was smoother. Furthermore, after boriding at a low temperature of 700℃ for 8 h, a boride layer of about 5 μm formed on the NS surface. This layer was toothlike and wedged into the substrate, which made the surface layer combine well with the substrate. The phase of the boride layer was Fe2B. Research on boriding kinetics indicated that the activation energy was decreased for the treated samples.

Recent developments of the high strength and high ductility nanostructured materials

This talk will summarize the recent work related to a kind of new nanomaterials produced by the SMAT (surface mechanical attrition treatment).The concept of surface nanocrystallization of materials will be presented.In terms of the grain refinement mechanism induced by plastic deformation,a novel surface mechanical attrition(SMA) technique was developed for synthesizing a nanostructured surface layer on metallic materials in order to upgrade the overall properties and performance.The grain refinement mechanism of the surface layer during the SMA treatment will be analyzed in terms of the nanostructure observations in several typical materials.Very high yield stress(5 times of the base material) on the surface layer of the material obtained by the SMAT has been observed.The effect of surface nanostructures on the mechanical behavior and on the failure mechanism of metallic material shows the possibility to develop a new strength gradient composite using co-rolling and nitriding.The role of residual stress induced during the treatment will be investigated and discussed.The developed materials are also porosity free materials which can be used as reference material for the local mechanical behavior investigation technique such as the nanoindentation.A general concept for obtaining high strength and high ductility nanostructured materials will be presented.The exceptional high strength and high ductility steels have developed.The simulation of the mechanisms for improving ductility of high strength nanostructured materials will be presented.The potential applications for the land transportation vehicles(car,bus,train) and wind energy have been investigated.Some examples of concept design for the integration of the advanced nanostructured steels will be presented.

Microstructure and Mechanical Properties of Al/Al_4C_3/Al_2O_3 Composite

icrostructure and mechanical properties of Al_4C_3 and Al_2O_3 dispersion strengthened aluminum composite fabricated by mechanical attrition and hotpressing consolidation method were studied. It was shown that fine well developed Al_4C_3 stick and equiaxed γAl_2O_3 dispersoids with total content of about 6.6 v% uniformly distributed within the Al grains or along the grain boundaries. The Al/Al_4C_3 and Al/Al_2O_3 interfaces are very clean and well bonded at atomic level, but have no fixed orientation relationships between the dispersoids and the aluminum matrix exists. At ambient and especially elevated temperatures, strength and stiffness of the composite are much higher than that of P/M Al and even better than that of the 15 v% SiCw/Al composite.

A multi-scale grained microstructure of the surface nanocrystallized 304 stainless steel sheets after warm-rolling

An ultrafine grained microstructure was obtained for 304 stainless steel(304SS)sheets by using surface nanocrystallization and warm-rolling.The microstructure and mechanical properties were determined by X-ray diffraction(XRD),transmission electron microscope(TEM)and a test on microhardness.Experimental results were shown that the microstructure was featured by a continuous distribution from the nanocrystalline on the surface to micro-grains in the center,in which the volume fraction of the micro-sized grains is about 40% in the surface layer.This multi-scale grained microstructure was composed of austenite and martensite phases with a gradient increasing volume fraction of austenite from the surface to the centre.The microhardness of the resultant steel was higher than 150% of that as received,due to the refined grains and strain-induced martensitic transformation.The hardness distribution was consistent with the microstructural variation,suggesting a good combination of high strength and improved ductility.

Effect of Surface Mechanical Attrition Treatment on Corrosion Behavior of 316 Stainless Steel

The nanocrystalline microstructure of the surface of 316 stainless steel （316SS） induced by surface mechanical attrition treatment （SMAT） was determined by X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The technique of hydrogen embrittlement was first used to obtain the information of the brittleness cleavage plane. The effects of SMAT and the following annealing process on the corrosion behavior of 316SS were investiga- ted by potentiodynamic polarization curves and potentiostatic critical pitting temperature measurements. The results demonstrated that the nanoerystalline layer with an average grain size of 19 nm was produced. However, there were lots of cracks on the surface, which led to the degradation in the corrosion resistance of 316SS after SMAT. Never- theless, after annealing treatment, the corrosion resistance of the nanocrystalline surface had been improved greatly. The higher the annealing temperature, the better was the corrosion resistance.

Effect of mechanical attrition on microstructure and properties of electro-deposition coatings on NdFeB

Surface mechanical attrition treatment （SMAT） was developed to synthesize nanostructure coatings on alloy surface. The SMAT action was applied in the process of Ni and Cu electroplating coatings on NdFeB substrates in this paper. The role of mechanical attrition during barrel plating on the microstructure, mechanical and corrosion resistant properties of the coatings was exam- ined. The scanning electron microscopy （SEM） observation showed that the mechanical attrition could refine grain size, markedly smooth the coating surface and obviously decrease the number of pore in the coatings. The continuous collisions of glass balls onto the NdFeB samples could induce more beneficial nucleation defects on the coating, which was helpful for increasing nucleation sites and the nucleation rate. The mechanical attrition could also restrain the heterogeneous growth of the coating grain tips due to the abra- sive action of stainless steel balls. The Tafel polarization curve experimental results indicated that SMAT process could enhance the corrosion resistance of coatings on NdFeB. The scratching test revealed that the binding force between coating and NdFeB substrate could be improved dramatically with SMAT process.

Strain-induced Microstructure Refinement in a Tool Steel Subjected to Surface Mechanical Attrition Treatment

A nanostructured surface layer has been fabricated on an AISI H13 tool steel by means of surface mechanical attrition treatment （SMAT）.Strain-induced refinement processes of ferrite grains and carbide particles have been investigated by transmission electron microscopy （TEM） and scanning electron microscopy （SEM） in the SMAT surface layer.Grain refinement of ferrite is found to be dominated by dislocation activities and greatly facilitated by a large number of carbide particles at a depth 〉20 μm.The comparisons with microstructure refinement processes in other SMAT ferrite steels indicate that a larger volume fraction of carbide particles with a lower shear strength is expected to facilitate the refinement process of ferrite grains.

Thermal Stability of Nanocrystalline AZ31 Magnesium Alloy Fabricated by Surface Mechanical Attrition Treatment

A nanocrystalline layer （NL） was fabricated on the surface of AZ31 magnesium （Mg） alloy sheet by surface mechanical attrition treatment （SMAT）. The microstructure of the Mg alloy was characterized by optical microscopy, X-ray diffraction and microhardness test. The results showed that both the microstructure and microhardness of AZ31 Mg alloy sheet after SMAT revealed a gradient distribution along depth from surface to center. The thermal stability of the NL was investigated through characterizing the microstructure evolution during the post-isothermal annealing treatment within the temperature range from 150 to 250℃. The NL exhibits a certain degree of thermal stability below 150 ℃, while it disappears quickly when annealing at the temperature range of 200-250 ℃. The grain growth kinetics of the nanocrystalline of AZ31 Mg alloy induced by SMAT was investigated. The activation energy of nanocrystalline AZ31 Mg alloy was obtained with a value of 92.8 kJ/mol.

The Portevin-Le Chatelier effect of gradient nanostructured 5182 aluminum alloy by surface mechanical attrition treatment

Nanocrystalline surface layers and gradient nanostructure in 5182 aluminum alloy have been produced through surface mechanical attrition treatment(SMAT). The results indicate that the gradient nanostructure can not only improve the mechanical properties of 5182 Al alloy, but also has a certain effect on the Portevin-Le Chatelier(PLC) effect. The yield and ultimate tensile strength of 5182 Al alloy with SMAT are significantly improved combining with the decrease of fracture elongation compared with the as-received one. The PLC effect of 5182 Al alloy could be effectively postponed by the formation of gradient nanostructure after SMAT. It leads to the increase of critical strain of the PLC effect, more concentrated distribution of serrated strain, and increase of average stress amplitude in special strain range. The influence of grain size and gradient nanostructure on the PLC effect of 5182 Al alloy was also discussed in detail. Grain refinement could sharply increase the density of dislocations and hinder the movement of dislocations, which results in the decrease of moving speed of dislocations and the more concentrated distribution of solute atoms. The solute atoms would aggregate to form nano precipitates and further impede movement of dislocation. The stronger interaction between the dislocations and the nano precipitates is the main mechanism of postponed PLC effect.

Effect of Surface Mechanical Attrition Treatment on Tribological Behavior of the AZ31 Alloy

By surface mechanical attrition treatment（SMAT）,a gradient nano structure（GNS） from the surface to center was generated in the AZ31 alloy sheet.The tribological behavior of AZ31 alloy with GNS was systematically investigated by using dry sliding tests,a 3D surface profile-meter and a scanning electron microscope equipped with an energy-dispersive spectrometer.The experimental results indicate that the Mg alloy with GNS exhibits better wear resistance comparing to the as-received sample,which is associated to the alteration of wear mechanism at different sliding speeds.The Mg alloy with GNS presents the wear mechanism of the abrasive wear at 0.05 m/s and the oxidative wear at 0.5 m/s,respectively.Moreover,the GNS can effectively promote the reaction between the oxygen and worn surface,which leads to a compact oxidation layer at 0.5 m/s.The effect of oxidation layer on the wear resistance of the Mg alloy was also discussed.

Effect of surface mechanical attrition treatment of titanium using alumina balls： surface roughness, contact angle and apatite forming ability

The effect of surface mechanical attrition treatment （SMAT） of commercially pure titanium （CP-Ti） using 8 mm O alumina balls was studied. SMAT induced plastic deformation, increased the surface roughness, reduced the grain size and decreased the contact angle （from 64° to 43°） with a corresponding increase in surface energy （from 32 to 53 mJ/m2）. Untreated CP-Ti and those treateded using alumina bails for 900 s reveals no apatite growth until the 28th day of immersion whereas those treated for 1800 and 2700 s exhibit apatite growth In selective areas and the extent of growth is increased with increase in immersion time an SBF; The study reveals that SMAT using alumina balls is beneficial in imparting the desired surface Cheracteristics, provided the surface contamination is limited, which would otherwise decrease the apatite forming ability.

Serrated plastic flow behavior and microstructure in a Zr-based bulk metallic glass processed by surface mechanical attrition treatment

The serrated plastic flow,microstructure and residual stress of a Zr_（55）Cu_（30）Ni_5Al_（10） bulk metallic glass（BMG）undergone surface mechanical attrition treatment（SMAT）have been investigated by a combination of compression tests with scanning electron microscopy（SEM）,high resolution transmission electron microscopy（HRTEM）and the incremental hole-drilling strain-gage method.It is found that SMAT leads to various microstructural modifications and residual stress distribution in the surface layers of the Zrbased BMG due to the mechanically-induced nanocrystallization and generation of shear bands.As a result,the BMG alloy exhibits a remarkable work-hardening like behavior and significant increase of plastic strain from less than 1%to 15%,and its plastic deformation dynamics yields a power-law distribution of shear avalanches.Based upon the analysis of the experimental results,it is indicated that this can be connected to the SMAT-induced microstructural modifications and the resulting residual compressive stress in the Zr-based BMG.