INFLUENCE OF AUSTENITIZING TEMPERATURE ON IMPURITY SEGREGATION ALONG GRAIN BOUNDARIES IN STEEL 4330M

The effect of austenitizing temperature on segregation of impurities along grain boundaries in steel 4330M has been examined by AES.The impurity segregation was computed quantitatively.Results showed that the quantity of impurity segregation changed with the austenitizing temperature.The limitation of the McLean′s expression for equilibrium segrega- tion was discussed.

Influence of Austenitizing Temperature on the Microstructure and Corrosion Resistance of 55Cr18Mo1VN High-Nitrogen Plastic Mould Steel

The influence of austenitizing temperature on the microstructure and corrosion resistance of 55Cr18MolVN high-nitrogen plastic mould steel was investigated. The microstructure, elemental distribution and Cr-depleted zone of different heat-treated samples were investigated by X-ray diffraction, electron probe microanalyzer analysis, and trans- mission electron microscopy. The corrosion resistance was evaluated using electrochemical measurements, and the analysis of passive film was carded out by X-ray photoelectron spectroscopy. The results indicated that the volume fraction of precipitates decreased, and the homogeneity of elements was improved with increasing austenitizing temperature. The degree of Cr-depleted zone around coarse M23C6 was severer than that around M2N, and pitting corrosion initiated preferentially around M23C6. The corrosion resistance of the samples increased with the austenitizing temperature. With the increase in austenitizing temperature, the passive film was thickened and Cr（III）cr2O3 in the inner layer of passive film was enriched, which enhanced the corrosion resistance of the steel. The higher content of nitrogen in solid solution at higher austenitizing temperature contributed to the increased intensity of CrN and NH3, leading to the increase in pH value in the pit, and promoting the repassivation of 55Cr18Mo1N steel.

Reheating Austenitizing Temperature of Spring Steel 60Si2MnA for Railway

The microsturctural transformation of austenite grain, pearlite interlamellar spacing, and lamellar cement ite thickness of spring steel 60Si2MnA for railway were studied in the hot-rolled and reheated states. Furthermore, the effect of microstructural characterization on its final mechanical properties was discussed. The results showed that as far as 60Si2MnA, the pearlite interlamellar spacing determined the hardness, whereas, the austenite grain determined the toughness. Compared with microstructure and mechanical properties in the hot rolled state, after reheating treatment at 950 ℃, its average grain sizes are apparently fine and the pearlite interlamellar spacing and lamellar cementite thickness coarsen to some extent, but both hardness and impact toughness increase to HRC 48 and 8.5 J, respectively. In the course of making spring, the optimum reheating austenitizing temperature for the 60Si2MnA steel is 950 ℃.

Effect of austenitization temperature on microstructure and mechanical properties of low-carbon-equivalent carbidic austempered ductile iron

The wear resistances of austempered ductile iron （ADI） were improved through intxoduction of a new phase （carbide） into the ma- txix by addition of chromium. In the present investigation, low-caxbon-equivalent ductile iron （LCEDI） （CE = 3.06%, and CE represents cax- bon-equivalent） with 2.42% chromium was selected. LCEDI was austeintized at two difl＇erent temperatures （900 and 975~C） a^ld soaked for 1 h and then quenched in a salt bath at 325~C for 0 to 10 h. Samples were analyzed using optical microscopy and X-ray diffraction. Wear tests were carded out on a pin-on-disk-type machine. The efl＇ect of austenization temperature on the wear resistance, impact strength, and the mi- crostructure was evaluated. A stxucture-property correlation based on the observations is established.

Influence of cooling rate on phase transformation and microstructure of Ti-50.9%Ni shape memory alloy

Heat treatment of Ti-50.9%Ni （mole fraction） alloy was studied by differential scanning calorimetry, X-ray diffraction, scanning electron microscopey and energy dispersive X-ray analysis to investigate the influence of cooling rate on transformation behavior and microstructures of NiTi shape memory alloy. The experimental results show that three-stage phase transformation can be induced at a very low cooling rate such as cooling in furnace. The cooling rate also has a great influence on the phase transformation temperatures. Both martensitic start transformation temperature （Ms） and martensitic finish transformation temperature （Mf） decrease with the decrease of the cooling rate, and decreasing the cooling rate contributes to enhancing the M→A austenite transformation temperature. The phase transformation hysteresis （Af-Mf） increases with the decrease of the cooling rate. Heat treatment is unable to eliminate the textures formed in hot working of NiTi sample, but can weaken the intensity of them. The cooling rate has little influence on the grain size.

Effects of Nitrogen Content and Austenitization Temperature on Precipitation in Niobium Micro-alloyed Steels

The influences of nitrogen content and austenitization temperature on Nb（C, N） precipitation in niobium micro-alloyed steels were studied by different methods： optical microscopy, tensile tests, scanning electron mi- croscopy, transmission electron microscopy, physicochemical phase analysis, and small-angle X-ray scattering. The results show that the strength of the steel with high nitrogen content is slightly higher than that of the steel with low nitrogen content. The increase in the nitrogen content does not result in the increase in the amount of Nb（C,N） precipitates, which mainly depends on the niobium content in the steel. The mass fraction of small-sized Nb（C, N） precipitates （1--10 nm） in the steel with high nitrogen content is less than that in the steel with low nitrogen con- tent. After austenitized at 1 150 ℃, a number of large cuboidal and needle-shaped particles are detected in the steel with high nitrogen content, whereas they dissolve after austenitized at 1 200 ℃ and the Nb（C,N） precipitates become finer in both steels. Furthermore, the results also show that part of the nitrogen in steel involves the formation of al- loyed cementite.

Analytical Investigation of Prior Austenite Grain Size Dependence of Low Temperature Toughness in Steel Weld Metal

Prior austenite grain size dependence of the low temperature impact toughness has been addressed in the bainitic weld metals by in situ observations.Usually,decreasing the grain size is the only approach by which both the strength and the toughness of a steel are increased.However,low carbon bainitic steel with small grain size shows a weakening of the low temperature impact toughness in this study.By direct tracking of the morphological evolution during phase transformation,it is found that large austenite grain size dominates the nucleation of intragranular acicular ferrite,whereas small austenite grain size leads to grain boundary nucleation of bainite.This kinetics information will contribute to meet the increasing low temperature toughness requirement of weld metals for the storage tanks and offshore structures.

Tensile behavior and deformation mechanism of quenching and partitioning treated steels at different deforming temperatures

The effects of deforming temperatures on the tensile behaviors of quenching and partitioning treated steels were investigated. It was found that the ultimate tensile strength of the steel decreased with the increasing temperature from 25 to 100 ℃, reached the maximum value at 300 ℃, and then declined by a significant extent when the temperature further reached 400 ℃. The total elongations at 100, 200 and 300 ℃are at about the same level. The steel achieved optimal mechanical properties at 300 ℃due to the proper transformation behavior of retained austenite since the stability of retained austenite is largely dependent on the deforming temperature. When tested at 100 and 200 ℃, the retained aus tenite was reluctant to transform, while at the other temperatures, about 10 vol. % of retained aus- tenite transformed during the tensile tests. The relationship between the stability of retained austenite and the work hardening behavior of quenching and partitioning treated steels at different deforming temperatures was also studied and discussed in detail. In order to obtain excellent mechanical properties, the stability of retained austenite should be carefully controlled so that the effect of transforma tion-induced plasticity could take place continuously during plastic deformation.

Comparison of microstructure and property of high chromium bearing steel with and without nitrogen addition

Microstructure and property of bearing steel with and without nitrogen addition were investigated by microstructural observation and hardness measurement after different heat treatment processing. Based on the microstructural observation of both 9Cr18 steel and X90N steel, it was found that nitrogen addition could effectively reduce the amount and size of coarse carbides and also refine the original austenite grain size. Due to addition of nitrogen, more austenite phase was found in X90N steel than in 9Cr18 steel. The retained austenite of X90N steel after quenching at 1050℃ could be reduced from about 60% to about 7 9% by cold treatment at -73℃ and subsequent tempering, and thus finally increased the hardness up to 60 HRC after low temperature tempering and to 63 HRC after high temperature tempering. Furthermore, both the wear and corrosion resistance of X90N steel were found much more superior than those of 9Cr18 steel, which was attributed to the addition of nitrogen. It was proposed at last that nitrogen alloying into the high chromium bearing steel was a promising way not only to refine the size of both carbides and austenite, but also to achieve high hardness, high wear property and improved corrosion resistance of the stainless bearing steel.