The contribution of leakage in a baghouse filter （defined as a short circuit between the upstream and downstream sides of the filter） to the emission of fine particles is quantified in comparison to other dust emiss...The contribution of leakage in a baghouse filter （defined as a short circuit between the upstream and downstream sides of the filter） to the emission of fine particles is quantified in comparison to other dust emission sources, and the influence of key operating variables on overall system response is analyzed. The study was conducted on a well-maintained pilot-scale filter unit （9 bags of 500 g/m^2 calendered polyester needle felt; total surface area 4.2 m^2） operated in Ap-controlled mode over a range of pulsing intensities, with two types of test dust （one free-flowing and the other cohesive） at inlet concentrations of 10 and 30 g/m^3. Leaks included single holes between 0.5 and 4 mm diameter, intentionally placed in either the plenum plate or one of the filter bags, as well as seamlines from bag confectioning. Emissions were sep- arated by source into a transient contribution due to dust penetration through the filter bags after each cleaning pulse, and a continuous contribution from leaks. This separation was based on a novel method of data processing that relies on time-resolved concentration measurements with a specially calibrated optical particle counter. Tiny leaks on the order of 1 mm generated the same emission level as all the bags combined, and dominated continuous emissions. The equivalent leak cross section （leakage = media emission） was about 1 ppm of the total installed filter surface, independent of upstream dust concentra- tion. Leakage through open seamlines amounted to 75% of media emissions in case of free-flowing test dust. Leakage was restricted to aerodynamic diameters less than ~5 μm （roughly the PM2.s mass frac- tion）. For comparison, time-averaged mass penetration through conventional needle-felt media ranged from about 10^-5 to 10^-6, depending on cohesiveness of the particle material and pulse cleaning intensity, giving emission levels between about 0.02 and 0.2 mg/m^3 at the reference concentration of 10 R/m^2.展开更多
Concern over the health effects of fine particles in the ambient environment led the U.S. Environmental Protection Agency to develop the first standard for PM2.5 （particulate matter less than 2.5 μm） in 1997. The P...Concern over the health effects of fine particles in the ambient environment led the U.S. Environmental Protection Agency to develop the first standard for PM2.5 （particulate matter less than 2.5 μm） in 1997. The Particle Technology Laboratory at the University of Minnesota has helped to establish the PM2.5 standard by developing many instruments and samplers to perform atmospheric measurements. In this paper, we review various aspects of PM2.5, including its measurement, source apportionment, visibility and health effects, and mitigation. We focus on PM2.s studies in China and where appropriate, compare them with those obtained in the U.S. Based on accurate PM2.5 sampling, chemical analysis, and source apportionment models, the major PM2.5 sources in China have been identified to be coal combustion, motor vehicle emissions, and industrial sources. Atmospheric visibility has been found to correlate well with PM2.s concentration. Sulfate, ammonium, and nitrate carried by PM2.s, commonly found in coal burning and vehicle emissions, are the dominant contributors to regional haze in China. Short-term exposure to PM2.s is strongly associated with the increased risk of morbidity and mortality from cardiovascular and respiratory diseases in China. The strategy for PMzs mitigation must be based on reducing the pollutants from the two primary sources of coal-fired power plants and vehicle emissions. Although conventional Particulate Emission Control Devices （PECD） such as electrostatic precipitators in Chinese coal-fired power plants are generally effective for large particles, most of them may not have high collection efficiency of PM2.5. Baghouse filtration is gradually incorporated into the PECD to increase the PM2.5 collection efficiency. By adopting stringent vehicle emissions standard such as Euro 5 and 6, the emissions from vehicles can be gradually reduced over the years. An integrative approach, from collaboration among academia, government, and industries, can effectively manage and mitigate the PM2.s pollution in China.展开更多
文摘The contribution of leakage in a baghouse filter （defined as a short circuit between the upstream and downstream sides of the filter） to the emission of fine particles is quantified in comparison to other dust emission sources, and the influence of key operating variables on overall system response is analyzed. The study was conducted on a well-maintained pilot-scale filter unit （9 bags of 500 g/m^2 calendered polyester needle felt; total surface area 4.2 m^2） operated in Ap-controlled mode over a range of pulsing intensities, with two types of test dust （one free-flowing and the other cohesive） at inlet concentrations of 10 and 30 g/m^3. Leaks included single holes between 0.5 and 4 mm diameter, intentionally placed in either the plenum plate or one of the filter bags, as well as seamlines from bag confectioning. Emissions were sep- arated by source into a transient contribution due to dust penetration through the filter bags after each cleaning pulse, and a continuous contribution from leaks. This separation was based on a novel method of data processing that relies on time-resolved concentration measurements with a specially calibrated optical particle counter. Tiny leaks on the order of 1 mm generated the same emission level as all the bags combined, and dominated continuous emissions. The equivalent leak cross section （leakage = media emission） was about 1 ppm of the total installed filter surface, independent of upstream dust concentra- tion. Leakage through open seamlines amounted to 75% of media emissions in case of free-flowing test dust. Leakage was restricted to aerodynamic diameters less than ~5 μm （roughly the PM2.s mass frac- tion）. For comparison, time-averaged mass penetration through conventional needle-felt media ranged from about 10^-5 to 10^-6, depending on cohesiveness of the particle material and pulse cleaning intensity, giving emission levels between about 0.02 and 0.2 mg/m^3 at the reference concentration of 10 R/m^2.
文摘Concern over the health effects of fine particles in the ambient environment led the U.S. Environmental Protection Agency to develop the first standard for PM2.5 （particulate matter less than 2.5 μm） in 1997. The Particle Technology Laboratory at the University of Minnesota has helped to establish the PM2.5 standard by developing many instruments and samplers to perform atmospheric measurements. In this paper, we review various aspects of PM2.5, including its measurement, source apportionment, visibility and health effects, and mitigation. We focus on PM2.s studies in China and where appropriate, compare them with those obtained in the U.S. Based on accurate PM2.5 sampling, chemical analysis, and source apportionment models, the major PM2.5 sources in China have been identified to be coal combustion, motor vehicle emissions, and industrial sources. Atmospheric visibility has been found to correlate well with PM2.s concentration. Sulfate, ammonium, and nitrate carried by PM2.s, commonly found in coal burning and vehicle emissions, are the dominant contributors to regional haze in China. Short-term exposure to PM2.s is strongly associated with the increased risk of morbidity and mortality from cardiovascular and respiratory diseases in China. The strategy for PMzs mitigation must be based on reducing the pollutants from the two primary sources of coal-fired power plants and vehicle emissions. Although conventional Particulate Emission Control Devices （PECD） such as electrostatic precipitators in Chinese coal-fired power plants are generally effective for large particles, most of them may not have high collection efficiency of PM2.5. Baghouse filtration is gradually incorporated into the PECD to increase the PM2.5 collection efficiency. By adopting stringent vehicle emissions standard such as Euro 5 and 6, the emissions from vehicles can be gradually reduced over the years. An integrative approach, from collaboration among academia, government, and industries, can effectively manage and mitigate the PM2.s pollution in China.
