Ultra-high cycle fatigue behavior of high strength steel with carbide-free bainite/martensite complex microstructure

The ultra-high cycle fatigue behavior of a novel high strength steel with carbide-free bainite/martensite （CFB/M） complex microstructure was studied. The ultra-high cycle fatigue properties were measured by ultrasonic fatigue testing equipment at a frequency of 20 kHz. It is found that there is no horizontal part in the S-N curve and fatigue fracture occurs when the life of specimens exceeds 10^7 cycles. In addition, the origination of fatigue cracks tends to transfer from the surface to interior of specimens as the fatigue cycle exceeds 10^7, and the fatigue crack originations of many specimens are not induced by inclusions, but by some kind of ＂soft structure＂. It is shown that the studied high strength steel performs good ultra-high cycle fatigue properties. The ultra-high fatigue mechanism was discussed and it is suggested that specific CFB/M complex microstructure of the studied steel contributes to its superior properties.

Interaction of Hydrogen and Retained Austenite in Bainite/Martensite Dual-Phase High Strength Steel

The hydrogen trapping phenomena in two bainite/martensite dual-phase high strength steels(U20Si and U20DSi)were investigated by electrochemical permeation technique.The hydrogen diffusivity was calculated from data of permeation delay time,and the diffusion coefficient in U20 Si is far less than that in U20 DSi.Moreover,the hydrogen diffusivity decreases as the volume percent of retained austenite increases.The experiment results show that there are different hydrogen trappings and different volume percents of retained austenite in U20 Si and U20 DSi.The retained austenite is precipitated as films.The trap binding energy for the retained austenite and hydrogen is calculated to be 40.4kJ·mol-1.

Improving fatigue strength of bainite/martensite dual-phase steels in very high cycle fatigue regime by refining microstructures

Very high cycle fatigue behaviors of two bainite/martensite dual-phase steels were investigated.One of the steels was cyclic rapid heat treated and its microstructures were refined. Fatigue strength of the steel is 225 MPa higher than that without refining.Observation of fracture surfaces show that the fatigue cracks initiate at bainites for non-refined steel and at non-metallic inclusions for the refined steel.The size of inclusions is much smaller than that of bainites which results in the improvement of fatigue strength.

Effect of microstructure on corrosion behavior of high strength martensite steel-A literature review

The high strength martensite steels are widely used in aerospace,ocean engineering,etc.,due to their high strength,good ductility and acceptable corrosion resistance.This paper provides a review for the influence of microstructure on corrosion behavior of high strength martensite steels.Pitting is the most common corrosion type of high strength stainless steels,which always occurs at weak area of passive film such as inclusions,carbide/intermetallic interfaces.Meanwhile,the chromium carbide precipitations in the martensitic lath/prior austenite boundaries always result in intergranular corrosion.The precipitation,dislocation and grain/lath boundary are also used as crack nucleation and hydrogen traps,leading to hydrogen embrittlement and stress corrosion cracking for high strength martensite steels.Yet,the retained/reversed austenite has beneficial effects on the corrosion resistance and could reduce the sensitivity of stress corrosion cracking for high strength martensite steels.Finally,the corrosion mechanisms of additive manufacturing high strength steels and the ideas for designing new high strength martensite steel are explored.

Influence of rapid heating process on the microstructure and tensile properties of high-strength ferrite–martensite dual-phase steel

Three low-carbon dual-phase （DP） steels with almost constant martensite contents of 20vo1% were produced by intercritical annealing at different heating rates and soaking temperatures. Microstructures prepared at low temperature （1043 K, FH1） with fast-heating （300 K/s） show banded ferrite/martensite structure, whereas those soaked at high temperature （1103 K, FH2） with fast heating reveal blocky martensite uniformly distributed in the fine-grained ferrite matrix. Their mechanical properties were tested under tensile conditions and compared to a slow-heated （5 K/s） reference material （SH0）. The tensile tests indicate that for a given martensite volume fraction, the yield strength and total elongation values are noticeably affected by the refinement of ferrite grains and the martensite morphology. Metallographic observations reveal the formation of microvoids at the ferrite/martensite interface in the SH0 and FH2 samples, whereas microvoids nucleate via the fracture of banded martensite particles in the FH1 specimen. In addition, analyses of the work-hardening behaviors of the DP microstructures using the differential Crussard-Jaoul technique demonstrate two stages of work hardening for all samples.

Design of a low-alloy high-strength and high-toughness martensitic steel

To develop a high strength low alloy （HSLA） steel with high strength and high toughness, a series of martensitic steels were studied through alloying with various elements and thermodynamic simulation. The microstructure and mechanical properties of the designed steel were investigated by optical microscopy, scanning electron microscopy, tensile testing and Charpy impact test. The results show that cementite exists between 500℃ and 700℃, M7C3 exits below 720℃, and they are much lower than the austenitizing temperature of the designed steel. Furthermore, the Ti（C,N） precipitate exists until 1280℃, which refines the microstructure and increases the strength and toughness. The optimal alloying components are 0.19% C, 1.19% Si, 2.83% Mn, 1.24% Ni, and 0.049% Ti; the tensile strength and the V notch impact toughness of the designed steel are more than 1500 MPa and 100 J, respectively.

Complex Precipitation Mechanism of Ti-Nb-V Microalloyed Bainitic Base High Strength Steel

The addition of high Ti（>0.1%） in microalloyed bainitic high strength steel was designed, and the precipitation morphology of steels with different Ti, Nb, and V contents was studied by utilizing transmission electron microscopy（TEM）. Based on the classical nucleation-crystal growth theory and the Johnson-Mehl-Avrami equation, the precipitation thermodynamic and kinetic model of second phase particles in austenite was established in the form of（Nbx,Vy,Tiz）C, and the complex precipitation mechanism of second phase particles was emphatically studied. The experimental results show that the complex precipitation particles could be divided into two categories: the coarser particles with about 100 nm grain size and the independent complex precipitation particles in the form of（Nb,V,Ti）C with 35-50 nm grain size. The latter has a better precipitation strengthening effect, and the calculated PTT curve shows a typical "C" shape. When the deformed storage energy is 3 820 J?mol-1, the fastest precipitation temperature of calculated PTT curve is 925 °C, and the calculated result is essentially consistent with experimental values. The increase of Ti content increased the nose point temperature and expanded the range of fastest precipitation temperature.

Development of grain boundary allotriomorphic ferrite/granular bainite duplex steel

A new hot-rolled low alloy high strength steel with grain boundaryallotriomorphic ferrite/granular bainite duplex microstructure has been developed through novelmicrostructure and alloying designs without any noble metal elements such as nickel and molybdenum.Its as-rolled microstructure and mechanical properties, fatigue crack propagation behavior comparedwith single granular bainitic steel as well as continuous cooling transformation, were investigatedin detail. The measured result of CCT (continuous cooling transformation) curve shows that suchduplex microstructure can be easily obtained within a wide air-cooling rate range. More importantly,this duplex microstructure has much better combination of toughness and strength than the singlegranular bainite microstructure. It is found that the grain boundary allotriomorphic ferrite in thisduplex microstructure can blunt the microcrack tip, cause fatigue crack propagation route branchingand curving, and thus it increases the resistance to fatigue crack propagation, improves steeltoughness. The mechanical properties of the above commercial duplex steel plates have achieved orexceeded 870 MPa ultimate tensile strength, 570 MPa yield strength, 18 percent elongation and 34 JCharpy V-notch impact energy at -40 deg C, showing good development potential.

Latest Development and Application of High Strength and Heavy Gauge Pipeline Steel in China

Over the past twenty years, significant advances have been made in the field of microalloying and associated applications, among which one of the most successful application cases is HTP practice for heavy gauge, high strength pipeline steels. Combined the strengthening effects of TMCP and retardation effects of austenite recrystallization with increasing Nb in austenite region, HTP conception with low carbon and high niobium alloy design has been successfully applied to develop X80 coil with a thickness of 18.4 mm used for China＇s Second West-East pipeline. During this process, big efforts were made to further develop and enrich the application of microalloying technology, and at the same time the strengthening effects of Nb have been completely unfolded and fully utilized with improved metallurgical quality and quantitative analysis of microstructure. In this paper, the existing status and strengthening effect of Nb during reheating, rolling and cooling have been analyzed and characterized based on mass production samples and laboratory analysis. As confirmed, grain refinement remains the most basic strengthening measure to reduce the microstructure gradient along the thickness, which in turn enlarges the processing window to improve upon low temperature toughness, and finally make it possible to develop heavy gauge, high strength pipeline steels with more challenging fracture toughness requirements. As stated by a good saying that practice makes perfect. Based on application practice and theoretical analysis, HTP has been extended to develop heavy gauge and high strength pipeline steels with increasing requirements, including X80 SSAW pipe with a thickness of 22.0 mm and above, X80 LSAW pipe combining heavy gauge and large diameter, heavy gauge X80 LSAW pipe with low temperature requirements, as well as X90 steels. In this paper, alloy design, production processing, as well as mechanical properties and microstructure used for these products would be illustrated.

FATIGUE PROPERTIES OF META-BAINITE IN STEEL 40CrMnSiMoVA

The microstructure,strength,toughness and fatigue properties of an ultra-high strength steel 40CrMnSiMoVA have been investigated.The so-called meta-bainite,composed of thin re- tained austenite films within or between the bainitic ferrite lathes was found in the steel after isothermally quenched at 300℃ for 1h.In comparison with the martensite structure obtained by isothermally quenching in martensite range,the meta-bainite has more excellent strength and plasticity,lower notch sensitivity,stronger strain harden ability,higher fatigue strength, longer strain or impact fatigue life,slower crack propagation rate and more remarkable overload effect on increasing fatigue life.

Research and development of hot-rolled ultra-high strength steel at Baosteel

The effects of the composition and cooling process on the microstructures and properties of hot-rolled ultra-high strength low alloy （HSLA） steel, complex phase steel and martensite steel were studied in the laboratory. And S700MC and MP1200 ultra-high strength steels were trial produced at the 1 880 mm hot-rolling line of Baosteel. Compared with conventional hot-rolled high strength products,the idea that water is alloy was applied in the newly developed hot-rolled ultra-high strength steel. By the use of the economical composition design and controlled cooling after hot-rolling effectively,ultra-high strength steel of different steel grades can be obtained.

Microstructure design and feasibility of hot stamping for new generation high strength multi-phase steels

Optimization of microstructure for new generation advanced high strength steels(AHSS ) for automobiles was briefly reviewed.Two different heat treatments(quenching partitioning austempering/QPA and quenching partitioning tempering/QPT) have been investigated to obtain optimal microstructures,which are made up of martensite(hard phase),retained austenite(soft phase),and carbide or nano-bainite.Combination of hot stamping and newly developed heat treatments is discussed.

Low temperature impact toughness of laser hybrid welded joint of high strength low alloy steel

High strength low alloy steel with 16 mm thickness was welded by using high power laser hybrid welding. Microstrueture was characterized by using optical microscopy, scanning electron microscopy （ SEM ） , transmission electron microscopy （TEM） and selected area electron diffraction （SAED）. Low temperature impact toughness was estimated by using Charpy V-notch impact samples selected from the upper part and the lower part at the same heterogeneous joint. Results show that the low temperature impact absorbed energies of weld metal are （202,180,165 J） of upper samples and （178,145,160 J） of lower samples, respectively. All of them increase compared to base metal. The embrittlement of HAZ does not occur. Weld metal primarily consists of refined carbide free bainite and a little granular bainite since laser hybrid welding owns the character of low heat input. Retained austenite constituent film ＂locates among the lath structure of bainitie ferrite. Refined bainitic ferrite lath and retained austenite constituent film provide better low temperature impact toughness compared to base metal.

Research on the design of cold rolled ultra high strength sheet steel

This study researches cold rolled ultra high strength martensitic steel processed by water quenching. It is found that both the quenching and overageing temperatures greatly influence the mechanical properties of martensitic steel. A tensile strength of 1500 MPa can be obtained from 0.2% C-1.8% Mn steel by soaking at 840℃,quenching at 700℃ and overageing at 200℃ for several minutes. The continuous cooling transformation （CCT） diagram reveals that full martensite can be obtained at a cooling rate of 100℃/s or higher; and at a cooling rate of 3 - 10℃/s,austenite barely decomposes at 700℃. For steel with 0.2% carbon and less manganese, austenite decomposition occurs before it is cooled to 700℃ at a cooling rate of 3 - 10℃/s, which leads to lower tensile strength. It is possible to reduce the manganese content of the 1500 MPa martensitic steel by increasing the quenching temperature. To increase the quenching temperature,the control of flatness during water quenching becomes a major concern.

High temperature strength and ductility of the(C+N)strengthening Fe-Cr-Mn(W,V)steels

Fe-Cr-Mn(W, V) austenite steels used as low radioactive structural materialsin fusion reactor have been investigated. The results show that the high temperature strength andthe creep fracture life of Fe-Cr-Mn(W, V) steels can be effectively improved through (C+N)complex-strengthening, so can be the high temperature ductility. The strength and ductility of thesteels are superior to that of SUS316 steels and JPCAS below 673 K. The relationship betweenstrength, ductility and the formation temperature is related to the evolution of deformationmicrostructure. The fracture and microstructure observation above 673 K indicates that the main wayto further improve ductility at high temperature is the control of carbide coarsening at the grainboundaries.

Microstructural Transformation and Precipitation of an Ultra-high Strength Steel under Continuous Cooling

We investigated phase transition and precipitation of ultra-high strength steel（UHSS）in a new ＂short process＂ with controlled rolling and controlled cooling.Thermalexpansion test combined with metallographic observation was used to research the continuous cooling transformation（CCT）curve.Moreover,the microstructuraltransformation and precipitation law was revealed by morphologicalobservation and alloying elements by electron probe micro-analyzer（EPMA）.Transmission electron microscopy（TEM）was utilized to analyze the composition and grain orientation of microstructure.The study showed that the measured criticaltransformation temperatures of Ac1 and Ac3 were 746 and 868 ℃,respectively.The CCT curve indicated that the undercooled austenite was transformed into proeutectoid ferrite and bainite with HV 520 in a broad range of cooling rate 0.1^（-1） ℃·s^（-1）.When subjected to a cooling rate of 1 ℃·s^（-1）,the undercooled austenite was divided into small-sized blocks by formed martensite.With further increase of cooling rate,micro-hardness increased dramatically,the microstructure of specimen was mainly lathe bainite（LB）,granular bainite（GB）,lath martensite（LM）and residualaustenite.By diffraction test analysis,it was identified that there was K-S orientation relationship between martensite and austenite for {110}_α//{111}_γ,{111}_α//{101}_γ.EPMA clearly showed that carbon diffused adequately due to staying for a long time at high temperature with a lower cooling rate of 2 ℃·s-1.Phase transition drive force was lower and the residualaustenite existed in the block form of Martensite austenite island（M-A）.With the increase of cooling rate to 10 ℃·s^（-1）,the block residualaustenite reduced,the carbon content of residualaustenite increased and α phase around the residualaustenite formed into a low carbon bainite form.

Microstructural analysis of the softened zone in the welding joint of 100 kg class hot-rolled extra-high-strength steel

Using the Gleeble 3500 thermal-mechanical system to simulate thermal cycles with different peak temperatures, the hardness and microstructure in the heat-affected zones of two kinds of 100 kg class hot-rolled extra-high-strength steel were compared. When the peak temperature of the thermal cycle was 800℃ ,incomplete transformation occurred during quenching in both steels, and massive martensite and bainite grains were formed. The hardness was determined by the composition and distribution of the microstructure. The concentration of massive martensite was low, and hence the hardness was low,in steel #1. Conversely,the massive martensite content in steel #2 was high and uniformly distributed,resulting in a high hardness. These findings can provide a reference for improving the mechanical properties in the softened zone.

Effect of Microstructure on Corrosion Fatigue Behavior of 1500 MPa Level Carbide-Free Bainite/Martensite Dual-Phase High Strength Steel

Influence of microstructure of the experimental steels on the corrosion fatigue behavior in 3.5% of NaCl aqueous solution was studied.Experimental results show that compared with the full martensite（FM）steel,the carbide-free bainite/martensite（CFB/M）steel has higher corrosion fatigue strength and corrosion fatigue crack threshold（ΔKthcf）,and lower corrosion crack propagation rate [（da/dN）cf].

Research and modeling on correlation among microstructure,yield strength and process of bainite/martensite steel

The contributions of different strengthening mechanisms to yield strength of bainite/martensite multiphase rail steel with different finish cooling temperatures in the controlled cooling process were quantitatively investigated.Dislocation density and substructure size of the rail steel were measured by scanning electron microscopy,electron backscatter diffraction and X-ray diffraction.The results show that the dislocation density increases with the decrease in block width in rail steel.Based on the correlation among dislocation density,block width and yield strength,a physical model was proposed to predict the yield strength of rail steel.The variation of block width and dislocation density in different positions of rail head microstructure was integrated with temperature field simulation.Dislocation density and block width reveal significant correlations with the finish cooling temperature.

Microstructure evolution of an ultra-high strength metal alloy with tempering temperature

Optical microscopy (OM) and transmission electron microscopy (TEM) were used to investigate the effect of tempering temperature on the experimental extra-high carbon steels. It is found that tempering reaction can reduce austenite content and influence the stability of the austenite. As-normalized microstructure is a mixture of twinned martensite and retained austenite. Tempered at 250 °C for 2 h, lath martensite can occasionally be found nearby the diffusionally decomposed austenite area. It also is found that tempering at 650 °C for 2 h, nanoparticles of carbides precipitate in the martensite and decomposed austenite. © The Nonferrous Metals Society of China and Springer-Verlag Berlin Heidelberg 2012.