Background:Combined knee valgus and tibial internal rotation(VL+IR)moments have been shown to stress the anterior cruciate ligament(ACL)in several in vitro cadaveric studies.To utilize this knowledge for non-contact A...Background:Combined knee valgus and tibial internal rotation(VL+IR)moments have been shown to stress the anterior cruciate ligament(ACL)in several in vitro cadaveric studies.To utilize this knowledge for non-contact ACL injury prevention in sports,it is necessary to elucidate how the ground reaction force(GRF)acting point(center of pressure(CoP))in the stance foot produces combined knee VL+IR moments in risky maneuvers,such as cuttings.However,the effects of the GRF acting point on the development of the combined knee VL+IR moment in cutting are still unknown.Methods:We first established the deterministic mechanical condition that the CoP position relative to the tibial rotational axis differentiates the GRF vector’s directional probability for developing the combined knee VL+IR moment,and theoretically predicted that when the CoP is posterior to the tibial rotational axis,the GRF vector is more likely to produce the combined knee VL+IR moment than when the CoP is anterior to the tibial rotational axis.Then,we tested a stochastic aspect of our theory in a lab-controlled in vivo experiment.Fourteen females performed 60˚cutting under forefoot/rearfoot strike conditions(10 trials each).The positions of lower limb markers and GRF data were measured,and the knee moment due to GRF vector was calculated.The trials were divided into anterior-and posterior-CoP groups depending on the CoP position relative to the tibial rotational axis at each 10 ms interval from 0 to 100 ms after foot strike,and the occurrence rate of the combined knee VL+IR moment was compared between trial groups.Results:The posterior-CoP group showed significantly higher occurrence rates of the combined knee VL+IR moment(maximum of 82.8%)at every time point than those of the anterior-CoP trials,as theoretically predicted by the deterministic mechanical condition.Conclusion:The rearfoot strikes inducing the posterior CoP should be avoided to reduce the risk of non-contact ACL injury associated with the combined knee VL+IR stress.展开更多
The dynamic balancing is an important issue in mechanism design. For the existing balancing methods, both passive and active ones, there is still room for improvement in adaplability and independency. In view of this,...The dynamic balancing is an important issue in mechanism design. For the existing balancing methods, both passive and active ones, there is still room for improvement in adaplability and independency. In view of this, a concept of active balancer is developed as a new solution for the dynamic balancing with more flexibility. The proposed balancer is an independent additional device with a control system inside, which consists of a two-degree-of-freedom （DOF） linkage and a controllable motor, and can be attached to a machine expediently with little change to its original structure and motion. One of the two inputs of the two-DOF linkage shares the same shaft with its output, which is connected to the input shaft of a machine to be balanced and driven by the original actuator. The other input is driven by the control motor. By properly selecting the speed trajectories of the control motor and link parameters of the two-DOF linkage, one or more dynamic effects of the mechanisms can be minimized or eliminated adaptively. The design procedure of the active balancer is put forward and a two-step optimization is developed to find out optimal design parameters of the balancer for various design requirements and constraints. Taking a force-balanced crank-rocker mechanism as the reference mechanism, numerical examples are given to illustrate the design procedure. The balancing effects of the proposed balancer are compared with those of the existing adding dyads （DYAD） method. The results show that the introduction of the control system provides the active balancer with better balancing effect and more flexibility than the DYAD method. A considerable reduction in the dynamic effects （input torque, shaking moment and shaking force） can be achieved for different balancing object by designing the structural and control parameters of the balancer, and the deterioration of dynamic performance caused by alterative working conditions can be compensated effectively by redesigning the control parameters.展开更多
Joukowsky’s Lever Method is the method used to find out the equilibrant and balancingmoment of various mechanisms.The advantage of this method is to save the complicated processof finding out the reactional forces in...Joukowsky’s Lever Method is the method used to find out the equilibrant and balancingmoment of various mechanisms.The advantage of this method is to save the complicated processof finding out the reactional forces in kinematic pairs.But,the method is only limited to thosemechanisms composed of rigid bar linkages and with negligible friction.In practical cases,hydropneumatic elements and spring constraints may be included in the mechanism;and alsowith the development of high load,high speed and high accuracy of mechanism,the friction maynot be neglected.So,the authors have tried to develop the Generalized Joukowsky’s LeverMethod,which can be used to find out the equilibrant and balancing moment of the mechanismwhen the hydropneumatic elements and spring constraints are included and the friction inkinematic pairs has to be considered.Three examples are here analyzed to show the applicationsof this method.展开更多
Cloud dominates influence factors of atmospheric radiation, while aerosol–cloud interactions are of vital importance in its spatiotemporal distribution. In this study, a two-moment(mass and number) cloud microphysics...Cloud dominates influence factors of atmospheric radiation, while aerosol–cloud interactions are of vital importance in its spatiotemporal distribution. In this study, a two-moment(mass and number) cloud microphysics scheme, which significantly improved the treatment of the coupled processes of aerosols and clouds, was incorporated into version 1.1 of the IAP/LASG global Finite-volume Atmospheric Model(FAMIL1.1). For illustrative purposes, the characteristics of the energy balance and cloud radiative forcing(CRF) in an AMIP-type simulation with prescribed aerosols were compared with those in observational/reanalysis data. Even within the constraints of the prescribed aerosol mass, the model simulated global mean energy balance at the top of the atmosphere(TOA) and at the Earth’s surface, as well as their seasonal variation, are in good agreement with the observational data. The maximum deviation terms lie in the surface downwelling longwave radiation and surface latent heat flux, which are 3.5 W m-2(1%) and 3 W m-2(3.5%), individually. The spatial correlations of the annual TOA net radiation flux and the net CRF between simulation and observation were around 0.97 and 0.90, respectively. A major weakness is that FAMIL1.1 predicts more liquid water content and less ice water content over most oceans. Detailed comparisons are presented for a number of regions, with a focus on the Asian monsoon region(AMR). The results indicate that FAMIL1.1 well reproduces the summer–winter contrast for both the geographical distribution of the longwave CRF and shortwave CRF over the AMR. Finally, the model bias and possible solutions, as well as further works to develop FAMIL1.1 are discussed.展开更多
基金supported by the Grant-in-Aid for Young Scientists(B)Project(Grant No.24700716)funded by the Ministry of Education,Culture,Sports,Science and Technology,Japan.
文摘Background:Combined knee valgus and tibial internal rotation(VL+IR)moments have been shown to stress the anterior cruciate ligament(ACL)in several in vitro cadaveric studies.To utilize this knowledge for non-contact ACL injury prevention in sports,it is necessary to elucidate how the ground reaction force(GRF)acting point(center of pressure(CoP))in the stance foot produces combined knee VL+IR moments in risky maneuvers,such as cuttings.However,the effects of the GRF acting point on the development of the combined knee VL+IR moment in cutting are still unknown.Methods:We first established the deterministic mechanical condition that the CoP position relative to the tibial rotational axis differentiates the GRF vector’s directional probability for developing the combined knee VL+IR moment,and theoretically predicted that when the CoP is posterior to the tibial rotational axis,the GRF vector is more likely to produce the combined knee VL+IR moment than when the CoP is anterior to the tibial rotational axis.Then,we tested a stochastic aspect of our theory in a lab-controlled in vivo experiment.Fourteen females performed 60˚cutting under forefoot/rearfoot strike conditions(10 trials each).The positions of lower limb markers and GRF data were measured,and the knee moment due to GRF vector was calculated.The trials were divided into anterior-and posterior-CoP groups depending on the CoP position relative to the tibial rotational axis at each 10 ms interval from 0 to 100 ms after foot strike,and the occurrence rate of the combined knee VL+IR moment was compared between trial groups.Results:The posterior-CoP group showed significantly higher occurrence rates of the combined knee VL+IR moment(maximum of 82.8%)at every time point than those of the anterior-CoP trials,as theoretically predicted by the deterministic mechanical condition.Conclusion:The rearfoot strikes inducing the posterior CoP should be avoided to reduce the risk of non-contact ACL injury associated with the combined knee VL+IR stress.
基金supported by National Natural Science Foundation of China (Grant No. 50405004, 50875018)Key Project of National Natural Science Foundation of China (Grant No.50335040)
文摘The dynamic balancing is an important issue in mechanism design. For the existing balancing methods, both passive and active ones, there is still room for improvement in adaplability and independency. In view of this, a concept of active balancer is developed as a new solution for the dynamic balancing with more flexibility. The proposed balancer is an independent additional device with a control system inside, which consists of a two-degree-of-freedom （DOF） linkage and a controllable motor, and can be attached to a machine expediently with little change to its original structure and motion. One of the two inputs of the two-DOF linkage shares the same shaft with its output, which is connected to the input shaft of a machine to be balanced and driven by the original actuator. The other input is driven by the control motor. By properly selecting the speed trajectories of the control motor and link parameters of the two-DOF linkage, one or more dynamic effects of the mechanisms can be minimized or eliminated adaptively. The design procedure of the active balancer is put forward and a two-step optimization is developed to find out optimal design parameters of the balancer for various design requirements and constraints. Taking a force-balanced crank-rocker mechanism as the reference mechanism, numerical examples are given to illustrate the design procedure. The balancing effects of the proposed balancer are compared with those of the existing adding dyads （DYAD） method. The results show that the introduction of the control system provides the active balancer with better balancing effect and more flexibility than the DYAD method. A considerable reduction in the dynamic effects （input torque, shaking moment and shaking force） can be achieved for different balancing object by designing the structural and control parameters of the balancer, and the deterioration of dynamic performance caused by alterative working conditions can be compensated effectively by redesigning the control parameters.
文摘Joukowsky’s Lever Method is the method used to find out the equilibrant and balancingmoment of various mechanisms.The advantage of this method is to save the complicated processof finding out the reactional forces in kinematic pairs.But,the method is only limited to thosemechanisms composed of rigid bar linkages and with negligible friction.In practical cases,hydropneumatic elements and spring constraints may be included in the mechanism;and alsowith the development of high load,high speed and high accuracy of mechanism,the friction maynot be neglected.So,the authors have tried to develop the Generalized Joukowsky’s LeverMethod,which can be used to find out the equilibrant and balancing moment of the mechanismwhen the hydropneumatic elements and spring constraints are included and the friction inkinematic pairs has to be considered.Three examples are here analyzed to show the applicationsof this method.
基金funded by the National Natural Science Foundation of China (Grants 41675100, 91737306, and U1811464)
文摘Cloud dominates influence factors of atmospheric radiation, while aerosol–cloud interactions are of vital importance in its spatiotemporal distribution. In this study, a two-moment(mass and number) cloud microphysics scheme, which significantly improved the treatment of the coupled processes of aerosols and clouds, was incorporated into version 1.1 of the IAP/LASG global Finite-volume Atmospheric Model(FAMIL1.1). For illustrative purposes, the characteristics of the energy balance and cloud radiative forcing(CRF) in an AMIP-type simulation with prescribed aerosols were compared with those in observational/reanalysis data. Even within the constraints of the prescribed aerosol mass, the model simulated global mean energy balance at the top of the atmosphere(TOA) and at the Earth’s surface, as well as their seasonal variation, are in good agreement with the observational data. The maximum deviation terms lie in the surface downwelling longwave radiation and surface latent heat flux, which are 3.5 W m-2(1%) and 3 W m-2(3.5%), individually. The spatial correlations of the annual TOA net radiation flux and the net CRF between simulation and observation were around 0.97 and 0.90, respectively. A major weakness is that FAMIL1.1 predicts more liquid water content and less ice water content over most oceans. Detailed comparisons are presented for a number of regions, with a focus on the Asian monsoon region(AMR). The results indicate that FAMIL1.1 well reproduces the summer–winter contrast for both the geographical distribution of the longwave CRF and shortwave CRF over the AMR. Finally, the model bias and possible solutions, as well as further works to develop FAMIL1.1 are discussed.
