A band-pass frequency selective surface with polarization rotation

A band-pass frequency selective surface(FSS) with polarization rotation property is proposed. The proposed polarization rotating FSS(PR-FSS) is a two-dimensional periodic structure, its unit cell is an antenna-filter-antenna(AFA) module,and the polarization directions of the upper and lower antennas in each AFA module are orthogonal to each other, so the PR-FSS can achieve frequency selection and 90 degrees polarization rotation at the same time. The numerical simulation demonstrate that the anticipated frequency selection and polarization rotation are realized by the PR-FSS in the frequency band from 8.84 GHz to 10.30 GHz with a relative bandwidth of 15.26%, and the maximum insertion loss in the pass band is only 0.17 d B. Finally, one effective experiment validation is carried out, a reasonable agreement is observed between the experimental and simulated results except for a slight deviation caused by fabrication error and measurement tolerance.

Design of voltage-controlled dynamic band-pass filter based on VCA810

In order to filter signal effectively according to selective center frequency, a voltage-controlled dynamic band-pass filter with gain compensation was designed based on voltage-controlled gain wideband amplifier VCA810. The transfer function of the filter was analyzed and gain compensation voltages were given through tests; besides, a system was designed, including the gain compensation circuit and the control voltage circuit, etc. Center frequency will change from 1 kHz to 20 kHz according to control voltage on condition that bandwidth of the filter remains constant. The designed system has the advantages of simple structure, low noise, stable performance and convenient adjustment.

Electrically triggered dual-band tunable terahertz metamaterial band-pass filter based on Si_3N_4–VO_2–Si_3N_4 sandwich

We experimentally demonstrate an electrically triggered terahertz(THz) dual-band tunable band-pass filter based on Si_3 N_4–VO_2–Si_3 N_4 sandwich-structured hybrid metamaterials. The insulator–metal phase transition of VO_2 film is induced by the Joule thermal effect of the top metal layer. The finite-integration-time-domain(FITD) method and finite element method(FEM) are used for numerical simulations. The sample is fabricated using a surface micromachining process,and characterized by a THz time-domain-spectrometer(TDS). When the bias current is 0.225 A, the intensity modulation depths at two central frequencies of 0.56 THz and 0.91 THz are about 81.7% and 81.3%, respectively. This novel design can achieve dynamically electric–thermo–optic modulation in the THz region, and has potential applications in the fields of THz communications, imaging, sensing, and astronomy exploration.

Solar-blind ultraviolet band-pass filter based on metal–dielectric multilayer structures

Solar-blind ultraviolet （UV） band-pass filter has significant value in many scientific, commercial, and military appli- cations, in which the detection of weak UV signal against a strong background of solar radiation is required. In this work, a solar-blind filter is designed based on the concept of ＂transparent metal＂. The filter consisting of Al/SiO2 multilayers could exhibit a high transmission in the solar-blind wavelength region and a wide stopband extending from near-ultraviolet to infrared wavelength range. The central wavelength, bandwidth, Q factor, and rejection ratio of the passband are numerically studied as a function of individual layer thickness and multilayer period.

PHASE CORRECTION AND BAND-PASS FILTERS IN CT IMAGING

This paper reports the use of the fast Fourier transform (FFT) in the direct Fourier transform method (DFM) in Computerized Tomography (CT) reconstruction. Phase corrections are needed in the CT reconstruction. In order to eliminate the image distortion from the basic DFM, Padding and band-pass filters are used in the improved DFM. Finally, some reconstructions from simulated projections and several experimental results are given.

Tunable graphene-based mid-infrared band-pass planar filter and its application

We have designed and proposed the edge modes supported by graphene ribbons and the planar band-pass filter consist- ing of graphene ribbons coupled to a graphene ring resonator by using the finite-difference time-domain numerical method. Simulation results show that the edge modes improve the electromagnetic coupling between devices. This structure works as a novel, tunable mid-infrared band-pass filter. Our studies will benefit the fabrication of planar, ultra-compact nano-scale devices in the mid-infrared region. A power splitter consisting of two output ribbons that is useful in photonic integrated devices and circuits is also designed and simulated. These devices are useful for designing ultra-compact planar devices in photonic integrated circuits.

DUAL MODE WIDEBAND BAND-PASS FILTER WITH NOTCHED BAND FOR COMMUNICATION SYSTEM

This paper presents a planar microstrip wideband dual mode Band-Pass Filter(BPF) from 2 GHz to 3.4 GHz with a notched band at 2.62 GHz.The dual mode band-pass filter consists of a ring resonator with two quarter-wavelength open-circuited stubs at =90o and =0o,respectively.A square perturbation stub has been put at the corner of the ring resonator to increase the narrow stopbands and improve the performance of selectivity.By using a parallel-coupled feed line,a narrow notched band is introduced at the required frequency and its Fractional BandWidth(FBW) is about 5%.The proposed filter has a narrow notched band and a wide pass-band with a sharp cutoff frequency characteristic,the attenuation rate for the sharp cutoff frequency responses is 297.17 dB/GHz(cal-culated from 1.959 GHz with-34.43 dB to 2.065 GHz with-2.93 dB) and 228.10 dB/GHz(calculated from 3.395 GHz with-2.873 dB to 3.507 GHz with-28.42 dB).This filter has the advantages of good insertion loss in both operating bands and two rejections of greater than 16 dB in the range of 1.59 GHz to 1.99 GHz and 3.49 GHz to 3.98 GHz.Having been presented in this article,the measurement results agree well with the simulation results,which validates our idea.

Design of UWB Band-pass Filters with GPS Band Rejection

This paper presents a compact Ultra-Wideband （UWB） band-pass filter using a high-pass filter and a low-pass one, and the resonator with lumped elements. The structure of our proposed bandpass filter is very simple and the Defected Ground Structure（DGS） structure is used to get the low-pass filter characteristics. This proposed band-pass filter can be much smaller than a cascaded type filter. As a result of simulation, the insertion loss is less than 0.3 dB throughout the pass-band of 2.2 GHz- 10.6 GHz, while the return loss is more than 18 dB. And it has rejection level of 36 dB at GPS band.

Widening DGD Dynamic Range of DOP-based PMD Monitor Using Band-pass Filter

The theoretical and experimental analyses of widening the differential group delay (DGD) dynamic range of degree of polarization(DOP)-based polarization mode dispersion monitor using a band-pass filter are presented. The experiment shows that the maximum DGD monitoring range is widened up to ~6ps using band-pass filter. At the same time, DOP sensitivity has a little change. The experimental results are in accordance with the numerical ones.

Electromagnetic Band Gap Loaded Square Waveguide Band-Pass Filter for Dual-Polarized Application

An Electromagnetic Band Gap (EBG) loaded square waveguide Band-Pass Filter (BPF) is proposed in this paper. It’s simply composed by symmetrically loading periodical metal diaphragms on each wall of a square waveguide. The influences of insert sizes and loading periods on the overall BPF performances are analyzed. Experimental results agree well with those predicted. 6 GHz pass-band with insert loss less than 1 dB, 2.5 GHz stop-band and larger than 25 dB polarization isolation can be obtained. The BPF can be applied in dual-polarized waveguide-based antenna-feed systems.

A tunable dual-narrowband band-pass filter using plasma quantum well structure

A tunable dual-narrowband pass-band filter is designed. A one-dimensional photonic crystal （1D PC） is comprised of alternate dielectric layer and vacuum layer. Two quantum wells （QWs） as defects can be constructed by sandwiching two plasma slabs symmetrically in the 1D PC, and a dual-narrowband pass-band filter is formed. The conventional finite- difference time-domain （FDTD） method and piecewise linear current density recursive convolution （PLCDRC）-FDTD method are applied to the dielectric and plasma, respectively. The simulation results illustrate that the dual-narrowband frequencies can be tuned by changing the plasma frequency. The pass band interval and the half-power bandwidths （-3-dB band widths） are related to the space interval between two QWs.

无线传感节点中频域传输信号解调与控制方法

为提高无线传感网络节点中的频域传输信号抗噪能力,优化前端镜像与噪声信号处理能力,以无线传感节点中的频域传输信号为研究对象,提出一种新的信号控制与解调方法。将无线传感信号输入设计的滤波器中,通过电容器、电阻、运算放大器相互协作完成信号滤波。引入前馈补偿通路组建两级节点信号解调线路,当输出传感信号功率超过标准,便可根据超出值,以前馈补偿的方式调节增益带宽积实现解调。在传感节点中外接一个校正电路,以校正电容调节码的方式,控制传感信号频域传输特性满足正常运行标准。仿真结果表明:在1 V的电源电压下,此滤波器中心频率为2 MHz,邻近信号抑制为55 dB,镜像信号抑制为33 dB,带内纹波为0.1 dB,通带电压增益为18 dB,工作电流为382μA。验证了所提方法具有较高的频域传输信号深度处理能力,且有助于实现无线传感网络高质量通信。

基于多阶有源带通滤波器和在线相关系数的负载在线智能识别

从时域建立了负载在线识别的数学模型,识别任务由硬件和算法共同承担。采用多阶有源带通滤波器进行硬件预处理,从而将功率相差很大的负载信号转换成可以在同一个条件下采集的电压信号。从皮尔逊相关系数出发定义了在线相关系数,将其作为唯一的时域特征参量,并提出“在线相关系数逐渐增大并最终等于1”的判决准则。利用最大值首位对齐法和均值法进行数据处理,采用逐次比较法和筛选法相结合进行识别。实验数据表明:基于带宽为340~900 Hz的五阶有源带通滤波器和STM32处理器中的在线相关算法很好完成了功率相差1500多倍的电磁炉、电饭煲、笔记本电脑、小灯泡等4种负载的任意在线组合的智能识别。

Data processing method for aerial testing of rotating accelerometer gravity gradiometer

A novel method for noise removal from the rotating accelerometer gravity gradiometer(MAGG)is presented.It introduces a head-to-tail data expansion technique based on the zero-phase filtering principle.A scheme for determining band-pass filter parameters based on signal-to-noise ratio gain,smoothness index,and cross-correlation coefficient is designed using the Chebyshev optimal consistent approximation theory.Additionally,a wavelet denoising evaluation function is constructed,with the dmey wavelet basis function identified as most effective for processing gravity gradient data.The results of hard-in-the-loop simulation and prototype experiments show that the proposed processing method has shown a 14%improvement in the measurement variance of gravity gradient signals,and the measurement accuracy has reached within 4E,compared to other commonly used methods,which verifies that the proposed method effectively removes noise from the gradient signals,improved gravity gradiometry accuracy,and has certain technical insights for high-precision airborne gravity gradiometry.

一种提高变流器弱电网适应能力的虚拟阻抗控制策略

弱电网下较大的电网等值电感可能引起并网变流器失稳,为此,首先,建立了并网变流器的阻抗模型,根据阻抗比判据分析了电网等值电感对并网变流器稳定性的影响;其次,针对并网变流器对感性电网阻抗适应能力较低的问题,提出了一种基于带通滤波的虚拟阻抗控制策略,并研究了虚拟电阻值对变流器弱电网适应能力的影响,给出了虚拟电阻的选取原则;最后,搭建了系统仿真模型,仿真结果验证了文中理论分析的正确性和控制策略的有效性。

小型化宽阻带5G半集总混合滤波器设计

面向5G无线通信应用设计了一款微带半集总混合宽阻带带通滤波器。该滤波器阻带可扩展至5G毫米波频段,具有优良的带外抑制、结构紧凑及尺寸小巧的特点。搭建了集总元件的高频电路模型并完成了集总元件的路-场联合仿真,最终实现了由十字加载谐振器混合集总LC并联谐振电路而成的宽阻带滤波器。滤波器的中心频率位于4.08 GHz,通频带覆盖3.96~4.2 GHz,位于目前用于5G室内覆盖的N77频段。滤波器具有极广的阻带抑制特性,且优于20 dB抑制水平的上阻带范围可达22 GHz。滤波器有效电路尺寸仅为5.125mm×7.625 mm,插入损耗水平较低(0.54 dB),具有良好的选择性,适用于高性能5G通信系统应用。

全国产化微弱信号调理电路

为更好地处理微弱信号,提出一种新型的多通道信号前端调理模块。该模块不仅具有可编程增益功能,而且还整合了带通滤波器。在保证高输入阻抗和低噪声等关键性能的同时,提出一种全面而创新的调理模块设计方案。该方案的核心是采用可编程增益放大电路,显著提高了模块在放大各类微弱信号时的适应性。此外,利用HC595系列芯片,实现了对增益的精确调控。该放大电路具备26 dB的固定增益和0~84 dB的可调增益范围,工作带宽设定在380~420 kHz。经过系统性能测试,结果表明该调理电路成功满足了设计目标的各项要求。

基于文桥振荡器的高Q带通滤波器的设计

从单电阻调谐的文桥振荡器出发,首先导出该振荡器的振荡条件和振荡频率,然后给出了二阶带通滤波器的两种设计方案.第一种设计方案的优点是可以实现极点频率的单电阻调节,第二种方案的优点是极点频率和品质因数可正交调节.两种方案均可实现两个带通输出,均可调节电阻使电路振荡,而且振荡条件和振荡频率均可分别调节.通过计算机仿真证实了所设计的电路正确有效.

一种用于射频前端的谐波整形低功耗N通道滤波器

针对传统射频前端N通道滤波器功耗高,不能根据应用要求选择通过或抑制信号的高次谐波等问题,设计了一款谐波整形低功耗N通道滤波器。该滤波器通过添加具有适当权重的额外路径,可实现谐波抑制和整形的功能。同时,将本振Local Oscillator(LO)信号的n次谐波信号作为时钟信号,降低LO信号频率,时钟信号发生器的动态功耗降低到原来的1/n。SMIC 180 nm CMOS工艺的后仿真结果表明,10通道带通滤波器的中心频率在0.1~6.0 GHz可调,增益为0~5 dB,噪声系数小于4.6 dB,功耗为3.5~6.0 mW,输入三阶交调点(Input 3rd-order Intermodulation Point,IIP3)大于10 dBm,3次和5次谐波抑制分别大于65、90 dB,表明该滤波器具有谐波抑制和谐波整形的功能,且具有较低的功耗。

三种典型水声信号类型检测特性对比分析

水声信号的选择是传播损失调查工作中的重要环节,为进一步研究不同信号类型的检测性能,通过仿真研究与试验数据分析,对CW、扫频、伪随机编码这3种典型的水声信号类型检测性能进行了对比研究。其中,仿真研究使用射线理论模型中Bellhop程序计算宽带频域声信号,经傅里叶合成技术转化为时频声信号;信号检测性能分析采用带通滤波、匹配滤波和短时傅里叶变换方法开展。经对比后发现扫频信号和伪随机编码信号经匹配滤波后的信号主峰时频宽度小、幅度大,旁瓣小,易于区分,可获取信号多途到达结构,这对后续分析工作中反推反射系数有一定的优势。