New equations are proposed to describe the shapes and sizes of the contact areas between tire and ground(the contact areas)under the conditions of static load,slip,camber,and rolling.The equations are super ellipse an...New equations are proposed to describe the shapes and sizes of the contact areas between tire and ground(the contact areas)under the conditions of static load,slip,camber,and rolling.The equations are super ellipse and trigonometric function with four parameters.Results indicate that the contact areas under the conditions of static load,slip,camber can be well described by super ellipse,in the most complicated case,fourteen parameters are used.The rolling contact area can be reconstructed by the trigonometric function completely.Symmetrical and asymmetrical shapes can both be described perfectly.The suggested curves will make calculate size of the areas easily.The described shapes and sizes are in good agreement with the measured,the maximum deviation is only 2.88%.This work will provide an instrument for understanding the contact area and be helpful for analyzing tire and road.展开更多
Wastewater management and purification remain one of the greatest problems of mankind. The biological wastewater treatment technique uses a biofilm media carrier where microorganisms attach themselves to the surface. ...Wastewater management and purification remain one of the greatest problems of mankind. The biological wastewater treatment technique uses a biofilm media carrier where microorganisms attach themselves to the surface. This biofilter is usually made from virgin plastic pellets and can also be produced from recycled waste plastic and used in wastewater treatment. The need to treat water using low-cost carrier media has led to finding alternative sources of materials for biofilter manufacturing. Therefore, this work is centered on the recycling of waste plastic to make filaments which are then used for 3D printing of a high specific surface area (SSA) less clogging biofilm carrier through the parametric redesign. In the current study, the polypropylene material was recycled to make a 2.85 mm diameter filament compatible with the Ultimaker S3. Moreover, analytical models and governing equations were developed for the design of the K3 Kaldnes and MB3 media. Empirical surface area (SA), specific surface area, and volume of the respective carriers were determined using the model developed. SolidWorks was used to design and evaluate the same parameters which were then compared to model results. The errors in SSA obtained from the model with respect to the SolidWorks results for both the K3 Kaldnes and MB3 media were 0.34% and 0.76% respectively. With these small error margins, the model can serve as a tool and guideline for the designing of cylindrically shaped carriers. By transforming plastics into biofilters, waste plastics are mopped up reducing pollutions. Consequently, the deployment of such biofilters will enhance efficient wastewater treatment for a cleaner environment and the wellbeing of human race.展开更多
基金National Natural Science Foundation of China Project(51790502),Open Grant of National Key Laboratory of Science and Technology on Advanced Composites in Special Environments(JCKYS2019603C016)。
文摘New equations are proposed to describe the shapes and sizes of the contact areas between tire and ground(the contact areas)under the conditions of static load,slip,camber,and rolling.The equations are super ellipse and trigonometric function with four parameters.Results indicate that the contact areas under the conditions of static load,slip,camber can be well described by super ellipse,in the most complicated case,fourteen parameters are used.The rolling contact area can be reconstructed by the trigonometric function completely.Symmetrical and asymmetrical shapes can both be described perfectly.The suggested curves will make calculate size of the areas easily.The described shapes and sizes are in good agreement with the measured,the maximum deviation is only 2.88%.This work will provide an instrument for understanding the contact area and be helpful for analyzing tire and road.
文摘Wastewater management and purification remain one of the greatest problems of mankind. The biological wastewater treatment technique uses a biofilm media carrier where microorganisms attach themselves to the surface. This biofilter is usually made from virgin plastic pellets and can also be produced from recycled waste plastic and used in wastewater treatment. The need to treat water using low-cost carrier media has led to finding alternative sources of materials for biofilter manufacturing. Therefore, this work is centered on the recycling of waste plastic to make filaments which are then used for 3D printing of a high specific surface area (SSA) less clogging biofilm carrier through the parametric redesign. In the current study, the polypropylene material was recycled to make a 2.85 mm diameter filament compatible with the Ultimaker S3. Moreover, analytical models and governing equations were developed for the design of the K3 Kaldnes and MB3 media. Empirical surface area (SA), specific surface area, and volume of the respective carriers were determined using the model developed. SolidWorks was used to design and evaluate the same parameters which were then compared to model results. The errors in SSA obtained from the model with respect to the SolidWorks results for both the K3 Kaldnes and MB3 media were 0.34% and 0.76% respectively. With these small error margins, the model can serve as a tool and guideline for the designing of cylindrically shaped carriers. By transforming plastics into biofilters, waste plastics are mopped up reducing pollutions. Consequently, the deployment of such biofilters will enhance efficient wastewater treatment for a cleaner environment and the wellbeing of human race.
