CXCR4/SDF-1轴调节人肺腺癌PC-9细胞对Bends细胞血脑屏障模型功能的影响

目的:通过建立体外血脑屏障(blood brain barrier,BBB)模型,探讨人肺腺癌PC-9细胞在CXCR4/SDF-1轴作用下对BBB紧密连接蛋白的影响。方法:利用永生化的小鼠脑微血管内皮细胞Bends进行单层培养,建立体外BBB模型;通过跨内皮细胞电阻(transendothelial electrical resistance,TEER)测定及荧光素钠通透性实验判定体外BBB模型的功能状态以及观察PC-9细胞对体外BBB模型功能的影响。Western blotting检测PC-9细胞在CXCR4抑制剂AMD3100、SDF-1单独或联合(1μg/ml AMD3100,100 ng/ml SDF-1,AMD3100+SDF-1)作用下对BBB模型功能和内皮细胞紧密连接蛋白表达的影响,Transwell迁移实验检测CXCR4/SDF-1轴对PC-9细胞跨BBB模型细胞层迁移能力的影响。结果:Bends细胞单层培养可形成紧密连接的"屏障"并产生较高的TEER,第96 h达到(182.13±5.19)Ω·cm^2;同时行荧光色钠通透性实验结果显示,BBB具有良好屏障性能,其通透率低于空白对照组(P<0.05)。PC-9细胞作用后,BBB模型TEER逐渐降低,第24 h降至(46.7±4.35)Ω·cm^2;同时BBB通透率较作用前显著提高(P<0.05)。PC-9细胞在AMD3100作用下能够上调内皮细胞紧密连接蛋白的表达(P<0.05);AMD3100处理组的PC-9细胞穿过BBB的细胞数较空白组明显减少[(43±2)vs(81±2)个,P<0.05]。结论:AMD3100能够减弱PC-9细胞对Bends细胞建立的体外BBB模型紧密连接的破坏能力。

Experimental,Numerical,and Analytical Studies on the Bending of Mechanically Lined Pipe

Mechanically lined pipe(MLP)is often used for offshore oil and gas transport because of its low cost and corrosion resistance.During installation and operation,the pipe may undergo severe bending deformation,which causes the liner to separate from the outer pipe and buckles,affecting the stability of the whole line.In this paper,the buckling response of MLP subjected to bending is investigated to clarify its bending characteristics by employing both experiments,numerical simulation,as theoretical methods.Two types of MLPs were manufactured with GB 45 carbon steel(SLP)and Al 6061(ALP)used as the outer pipe material,respectively.The hydraulic expansion and bending experiments of small-scale MLPs are conducted.In addition to the ovalized shape of the cross-section for the SLP specimens,the copper liner was found to wrinkle on the compressive side.In contrast,the liner of ALP remains intact without developing any wrinkling and collapse mode.In addition,a dedicated numerical framework and theoretical models were also established.It was found both the manufacturing and bending responses of the MLP can be well reproduced,and the predicted maximum moment and critical curvatures are in good agreement with the experimental results.

Speed and surface steepness affect internal tibial loading during running

Background:Internal tibial loading is influenced by modifiable factors with implications for the risk of stress injury.Runners encounter varied surface steepness(gradients)when running outdoors and may adapt their speed according to the gradient.This study aimed to quantify tibial bending moments and stress at the anterior and posterior peripheries when running at different speeds on surfaces of different gradients.Methods:Twenty recreational runners ran on a treadmill at 3 different speeds(2.5 m/s,3.0 m/s,and 3.5 m/s)and gradients(level:0%;uphill:+5%,+10%,and+15%;downhill:-5%,-10%,and-15%).Force and marker data were collected synchronously throughout.Bending moments were estimated at the distal third centroid of the tibia about the medial-lateral axis by ensuring static equilibrium at each 1%of stance.Stress was derived from bending moments at the anterior and posterior peripheries by modeling the tibia as a hollow ellipse.Two-way repeated-measures analysis of variance were conducted using both functional and discrete statistical analyses.Results:There were significant main effects for running speed and gradient on peak bending moments and peak anterior and posterior stress.Higher running speeds resulted in greater tibial loading.Running uphill at+10%and+15%resulted in greater tibial loading than level running.Running downhill at-10%and-15%resulted in reduced tibial loading compared to level running.There was no difference between+5%or-5%and level running.Conclusion:Running at faster speeds and uphill on gradients≥+10%increased internal tibial loading,whereas slower running and downhill running on gradients≥-10%reduced internal loading.Adapting running speed according to the gradient could be a protective mechanism,providing runners with a strategy to minimize the risk of tibial stress injuries.

Effect of Pre-strain on Microstructure and Stamping Performance of High-strength Low-alloy Steel

In this study,pre-strain ranging from 0 to 0.12 was applied through uniaxial tension on high-strength low-alloy(HSLA)specimens with four kinds of grain size.Effect of pre-strain and grain size on me-chanical property was investigated through tensile tests.Microstructures of the pre-strained and tensile tested samples were analyzed,respectively.The 30.8°v-bending and following flattening,as well as Erichson cupping tests,were performed on the pre-strained samples.Results show the elongation ratio of grain and dislocation density increases with pre-strain.Yielding platform is removed when pre-strain is larger than 0.06 while yielding plateau period decreases with pre-strain less than 0.06 due to reduction of pinning effect.The 30.8°v-bending and the following flattening tests are successfully accomplished on all the pre-strained samples with different grain size.Decrease in grain size,along with increase in pre-strain,causes increase in strength and decrease in elongation rate as well as cupping value.Pre-strain causes very slight effect on bending ability,much less than that on mechanical property and cupping test value.Reciprocal impact of the pre-strain and grain size on HSLA steel deformability is inconspicuous.

Effect of characteristics and distribution of Mg_(17)Al_(12)precipitates on tensile and bending properties of high-Al-containing Mg alloys

This study investigates the effect of characteristics and distribution of Mg_(17)Al_(12)precipitates on the uniaxial tensile and three-point bending properties of extruded Mg alloys containing high Al contents.The extruded Mg–9Al–1Zn–0.3Mn(AZ91)alloy contains lamellar-structured Mg_(17)Al_(12)discontinuous precipitates along the grain boundaries,which are formed via static precipitation during natural air cooling.The extruded Mg–11Al–1Zn–0.3Mn(AZ111)alloy contains spherical Mg_(17)Al_(12)precipitates at the grain boundaries and inside the grains,which are formed via dynamic precipitation during extrusion.Due to inhomogeneous distribution of precipitates,the AZ111 alloy consists of two different precipitate regions:precipitate-rich region with numerous precipitates and finer grains and precipitate-scarce region with a few precipitates and coarser grains.The AZ111 alloy exhibits a higher tensile strength than the AZ91 alloy because its smaller grain size and more abundant precipitates result in stronger grain-boundary hardening and precipitation hardening effects,respectively.However,the tensile elongation of the AZ111 alloy is lower than that of the AZ91 alloy because the weak cohesion between the dynamic precipitates and the matrix facilitates the crack initiation and propagation.During bending,a macrocrack initiates on the outer surface of bending specimen in both alloys.The AZ111 alloy exhibits higher bending yield strength and lower failure bending strain than the AZ91 alloy.The bending specimens of the AZ91 alloy have similar bending formability,whereas those of the AZ111 alloy exhibit considerable differences in bending formability and crack propagation behavior,depending on the distribution and number density of precipitates in the specimen.In bending specimens of the AZ111 alloy,it is found that the failure bending strain(ε_(f,bending))is inversely proportional to the area fraction of precipitates in the outer zone of bending specimen(A_(ppt)),with a relationship ofε_(f,bending)=–0.1A_(ppt)+5.86.

Bending Failure Mode and Prediction Method of the Compressive Strain Capacity of A Submarine Pipeline with Dent Defects

A dent is a common type of defects for submarine pipeline.For submarine pipelines,high hydrostatic pressure and internal pressure are the main loads.Once pipelines bend due to complex subsea conditions,the compression strain capacity may be exceeded.Research into the local buckling failure and accurate prediction of the compressive strain capacity are important.A finite element model of a pipeline with a dent is established.Local buckling failure under a bending moment is investigated,and the compressive strain capacity is calculated.The effects of different parameters on pipeline local buckling are analyzed.The results show that the dent depth,external pressure and internal pressure lead to different local buckling failure modes of the pipeline.A higher internal pressure indicates a larger compressive strain capacity,and the opposite is true for external pressure.When the ratio of external pressure to collapse pressure of intact pipeline is greater than 0.1,the deeper the dent,the greater the compressive strain capacity of the pipeline.And as the ratio is less than 0.1,the opposite is true.On the basis of these results,a regression equation for predicting the compressive strain capacity of a dented submarine pipeline is proposed,which can be referred to during the integrity assessment of a submarine pipeline.

Discharge evolution law of debris flow based on a sharp bend physical modeling test

For the basins with debris flow development,its channel terrain exhibits a tortuous shape,which significantly restricts the movement of debris flows and leads to severe erosion effects on the concave bank.Therefore,this study aims to analyze the shear force of debris flows within the bend channel.We established the relationship between the shear force and bend curvature through laboratory experiments.Under the long-term erosion by debris flows,the curvature radius of bends gradually increases,however,when this increasing trend reaches an equilibrium state with the intensity of debris flow discharge,there will be no significant change in curvature radius.In general,the activity pattern and discharges of debris flows would remain relatively stable.Hence,we can infer the magnitude of debris flow discharges from the terrain parameters of the bend channel.

Cryogenic springback of 2219-W aluminum alloy sheet through V-shaped bending

A V-shaped bending device was established to evaluate the effects of temperature and bending fillet radius on springback behavior of 2219-W aluminum alloy at cryogenic temperatures.The cryogenic springback mechanism was elucidated through mechanical analyses and numerical simulations.The results indicated that the springback angle at cryogenic temperatures was greater than that at room temperature.The springback angle increased further as the temperature returned to ambient conditions,attributed to the combined effects of the “dual enhancement effect” and thermal expansion.Notably,a critical fillet radius made the springback angle zero for 90° V-shaped bending.The critical fillet radius at cryogenic temperatures was smaller than that at room temperature,owing to the influence of temperature variations on the bending moment ratio between the forward bending section at the fillet and the reverse bending section of the straight arm.

Analysis of deformation mechanisms in magnesium single crystals using a dedicated four-point bending tester

In this study,we explored the deformation mechanisms of Mg single crystals using a combination of scanning electron microscopy and electron backscattered diffraction in conjunction with a dedicated four-point bending tester.We prepared two single-crystal samples,oriented along the<1120>and<1010>directions,to assess the mechanisms of deformation when the initial basal slip was suppressed.In the<1120>sample,the primary{1012}twin(T1)was confirmed along the<1120>direction of the sample on the compression side with an increase in bending stress.In the<1010>sample,T1 and the secondary twin(T2)were confirmed to be along the<1120>direction,with an orientation of±60°with respect to the bending stress direction,and their direction matched with(0001)in T1 and T2.This result implies that crystallographically,the basal slip occurs readily.In addition,the<1010>sample showed the double twin in T1 on the compression side and the tertiary twin along the<1010>direction on the tension side.These results demonstrated that the maximum bending stress and displacement changed significantly under the bend loading because the deformation mechanisms were different for these single crystals.Therefore,the correlation between bending behavior and twin orientation was determined,which would be helpful for optimizing the bending properties of Mg-based materials.

Quick-scanning X-ray absorption fine structure beamline at SSRF

The layout and characteristics of the hard X-ray spectroscopy beamline(BL11B)at the Shanghai synchrotron radiation facility are described herein.BL11B is a bending-magnet beamline dedicated to conventional and millisecond-scale quick-scanning X-ray absorption fine structures.It is equipped with a cylindrical collimating mirror,a double-crystal monochromator comprising Si(111)and Si(311),a channel-cut quick-scanning Si(111)monochromator,a toroidal focusing mirror,and a high harmonics rejection mirror.It can provide 5-30 keV of X-rays with a photon flux of~5×10^(11)photons/s and an energy resolution of~1.31×10^(-4)at 10 keV.The performance of the beamline can satisfy the demands of users in the fields of catalysis,materials,and environmental science.This paper presents an overview of the beamline design and a detailed description of its performance and capabilities.

Bending strength degradation of a cantilever plate with surface energy due to partial debonding at the clamped boundary

This paper investigates the bending fracture problem of a micro/nanoscale cantilever thin plate with surface energy,where the clamped boundary is partially debonded along the thickness direction.Some fundamental mechanical equations for the bending problem of micro/nanoscale plates are given by the Kirchhoff theory of thin plates,incorporating the Gurtin-Murdoch surface elasticity theory.For two typical cases of constant bending moment and uniform shear force in the debonded segment,the associated problems are reduced to two mixed boundary value problems.By solving the resulting mixed boundary value problems using the Fourier integral transform,a new type of singular integral equation with two Cauchy kernels is obtained for each case,and the exact solutions in terms of the fundamental functions are determined using the PoincareBertrand formula.Asymptotic elastic fields near the debonded tips including the bending moment,effective shear force,and bulk stress components exhibit the oscillatory singularity.The dependence relations among the singular fields,the material constants,and the plate's thickness are analyzed for partially debonded cantilever micro-plates.If surface energy is neglected,these results reduce the bending fracture of a macroscale partially debonded cantilever plate,which has not been previously reported.

Simulation of Fracture Process of Lightweight Aggregate Concrete Based on Digital Image Processing Technology

The mechanical properties and failure mechanism of lightweight aggregate concrete(LWAC)is a hot topic in the engineering field,and the relationship between its microstructure and macroscopic mechanical properties is also a frontier research topic in the academic field.In this study,the image processing technology is used to establish a micro-structure model of lightweight aggregate concrete.Through the information extraction and processing of the section image of actual light aggregate concrete specimens,the mesostructural model of light aggregate concrete with real aggregate characteristics is established.The numerical simulation of uniaxial tensile test,uniaxial compression test and three-point bending test of lightweight aggregate concrete are carried out using a new finite element method-the base force element method respectively.Firstly,the image processing technology is used to produce beam specimens,uniaxial compression specimens and uniaxial tensile specimens of light aggregate concrete,which can better simulate the aggregate shape and random distribution of real light aggregate concrete.Secondly,the three-point bending test is numerically simulated.Thirdly,the uniaxial compression specimen generated by image processing technology is numerically simulated.Fourth,the uniaxial tensile specimen generated by image processing technology is numerically simulated.The mechanical behavior and damage mode of the specimen during loading were analyzed.The results of numerical simulation are compared and analyzed with those of relevant experiments.The feasibility and correctness of the micromodel established in this study for analyzing the micromechanics of lightweight aggregate concrete materials are verified.Image processing technology has a broad application prospect in the field of concrete mesoscopic damage analysis.

Multi-Objective Optimization of Aluminum Alloy Electric Bus Frame Connectors for Enhanced Durability

The widespread adoption of aluminumalloy electric buses,known for their energy efficiency and eco-friendliness,faces a challenge due to the aluminum frame’s susceptibility to deformation compared to steel.This issue is further exacerbated by the stringent requirements imposed by the flammability and explosiveness of batteries,necessitating robust frame protection.Our study aims to optimize the connectors of aluminum alloy bus frames,emphasizing durability,energy efficiency,and safety.This research delves into Multi-Objective Coordinated Optimization(MCO)techniques for lightweight design in aluminum alloy bus body connectors.Our goal is to enhance lightweighting,reinforce energy absorption,and improve deformation resistance in connector components.Three typical aluminum alloy connectors were selected and a design optimization platform was built for their MCO using a variety of software and methods.Firstly,through three-point bending experiments and finite element analysis on three types of connector components,we identified optimized design parameters based on deformation patterns.Then,employing Optimal Latin hypercube design(OLHD),parametric modeling,and neural network approximation,we developed high-precision approximate models for the design parameters of each connector component,targeting energy absorption,mass,and logarithmic strain.Lastly,utilizing the Archive-based Micro Genetic Algorithm(AMGA),Multi-Objective Particle Swarm Optimization(MOPSO),and Non-dominated SortingGenetic Algorithm(NSGA2),we explored optimized design solutions for these joint components.Subsequently,we simulated joint assembly buckling during bus rollover crash scenarios to verify and analyze the optimized solutions in three-point bending simulations.Each joint component showcased a remarkable 30%–40%mass reduction while boosting energy absorption.Our design optimization method exhibits high efficiency and costeffectiveness.Leveraging contemporary automation technology,the design optimization platform developed in this study is poised to facilitate intelligent optimization of lightweight metal components in future applications.

A modified 3D mean strain energy density criterion for predicting shale mixed-mode Ⅰ/Ⅲ fracture toughness

The fracture toughness of rocks is a critical fracturing parameter in geo-energy exploitation playing a significant role in fracture mechanics and hydraulic fracturing.The edge-notched disk bending(ENDB)specimens are employed to measure the entire range of mixed-modeⅠ/Ⅲfracture toughness of Longmaxi shale.To theoretically interpret the fracture mechanisms,this research first introduces the detailed derivations of three established fracture criteria.By distinguishing the volumetric and distortional strain energy densities,an improved three-dimensional mean strain energy density(MSED)criterion is proposed.As the critical volumetric to distortional MSED ratio decreases,the transition from tensiondominated fracture to shear-dominated fracture is observed.Our results indicate that both peak load and applied energy increase significantly with the transition from pure mode I(i.e.,tension)to pure modeⅢ(i.e.,torsion or tearing)since mode-Ⅲcracking happens in a twisted manner and mode-Ⅰcracking occurs in a coplanar manner.The macroscopic fracture signatures are consistent with those of triaxial hydraulic fracturing.The average ratio of pure mode-Ⅲfracture toughness to pure mode-Ⅰfracture toughness is 0.68,indicating that the obtained mode-Ⅲfracture resistance for a tensionbased loading system is apparent rather than true.Compared to the three mainstream fracture criteria,the present fracture criterion exhibits greater competitiveness and can successfully evaluate and predict mixed-modeⅠ/Ⅲfracture toughness of distinct materials and loading methods.

Effects of Temperature and Liquid Nitrogen(LN2)on Coal’s Mechanical and Acoustic Emission(AE)Properties

Liquid nitrogen has shown excellent performances as a good fracturing medium in the extraction of unconventional natural gas,and its application in coalbed methane extraction is currently a research hotspot.This study focuses on the acoustic emission properties of coal specimens treated utilizing liquid nitrogen with varying initial temperatures in a three-point bending environment.Through examination of the load-displacement curves of the considered coal samples,their mechanical properties are also revealed for different initial temperatures and cycling frequencies.The findings demonstrate a gradual decline in the maximum load capacity of coal rock as the temperature rises.Similarly,when subjected to the same temperature,an escalation in the cycling frequency leads to a reduction in the peak load of coal rock.This suggests that both temperature and cycling frequency exert a notable impact on the fracturing efficacy of liquid nitrogen.Freeze-thaw cycling treatments and exposure to high-temperature conditions can activate preexisting damage in the coal rock,and,accordingly,influence its mechanical properties.In particular,throughout the progressive loading of coal rock samples,the failure mechanisms are predominantly characterized by the occurrence of tensile cracks,succeeded by the development,spread,and fracture of shear fissures.

A Light and Simplified Branch Bending Method for Young Pear Trees

Aiming at high cost and low efficiency of conventional branch bending method in the modern intensive planting and labor-saving cultivation mode of young pear trees,this paper provides a new branch bending method with wide source of raw materials,cheap price and simple operation,which is also suitable for the management of low-age branches in the process of high grafting and upgrading of traditional big trees.

Analysis of the Characteristics of Materials Obtained by Recycling Scrap Metal in Guinea

The aim of this study was to determine the quality of rebar produced from recycled scrap metal collected throughout the country,and imported rebar sold in the Republic of Guinea.To do this,the samples were subjected to various mechanical tests involving traction,bending and microscopic analysis.In the Lambanyi and Casse Sonfonia samples,all the tensile strength values for diameters 12,14 and 16 were above 550 MPa.Conversely,the iron samples from Baillobaye and the 10 mm diameters of the samples from Casse Sonfonio and Lambanyi have less appreciable values.The limits of elasticity were determined.The various values found vary more or less from the conventional yield strength of the NF A35-016 reference supplied by CBITEC,which is 500 MPa.Microscopic analysis gives us an insight into the internal structure of the iron samples used.This study may provide the company and the vendors with an alternative for their improvements.

Study of the Characteristics of Large-Diameter Iron Bars Obtained by Rolling at the ODHAV Foundry in the Republic of Guinea

This work consists of evaluating the quality of the mechanical parameters of large-diameter steels, i.e. 20, 25, 28 and 32, through a process of recycling scrap metal that fills garages, rubbish dumps, gutters and other abandoned sites, as well as imported concrete reinforcing steel sold in the Republic of Guinea. To carry out this important work, a number of mechanical tensile and bending tests and a microscopic analysis combining two devices, an electron microscope and a photographic camera, were carried out. The samples were taken from sampling areas in the major communes of Conakry, namely: Casse Sonfonia, Matoto and Kagbélen. The tensile strength values of the large dimensions 20, 25, 28 and 32 are given in the tables.

The Effects of the Longitudinal Axis of Loading upon Bending, Shear and Torsion of a Thin-Walled Cantilever Channel Beam

Three aluminium channel sections of US standard extruded dimension are mounted as cantilevers with x-axis symmetry. The flexural bending and shear that arise with applied axial torsion are each considered theoretically and numerically in terms of two longitudinal axes of loading not coincident with the shear centre. In particular, the warping displacements, stiffness and stress distributions are calculated for torsion applied to longitudinal axes passing through the section’s centroid and its web centre. The stress conversions derived from each action are superimposed to reveal a net sectional stress distribution. Therein, the influence of the axis position upon the net axial and shear stress distributions is established compared to previous results for each beam when loading is referred to a flexural axis through the shear centre. Within the net stress analysis is, it is shown how the constraint to free warping presented by the end fixing modifies the axial stress. The latter can be identified with the action of a ‘bimoment’ upon each thin-walled section.

Nanoparticle Transport and Coagulation in Bends of Circular Cross Section via a New Moment Method

Transport of nanoparticles and coagulation is simulated with the combination of CFD in a circular bend. The Taylor-expansion moment method(TEMOM)is employed to study dynamics of nanoparticles with Brownian motion,based on the flow field from numerical simulation.A fully developed flow pattern in the present simulation is compared with previous numerical results for validating the model and computational code.It is found that for the simulated particulate flow system,the particle mass concentration,number concentration,particle polydispersity, mean particle diameter and geometric standard deviation over cross-section increase with time.The distribution of particle mass concentration at different time is independent of the initial particle size.More particles are concen-trated at outer edge of the bend.Coagulation plays more important role at initial stage than that in the subsequent period.The increase of Reynolds number and initial particle size leads to the increase of particle number concentration.The particle polydispersity,mean particle diameter and geometric standard deviation increase with decreasing Reynolds number and initial particle size.