Highly selective ethylbenzene production through alkylation of dilute ethylene with gas phase-liquid phase benzene and transalkylation feed

A novel industrial process was designed for the highly selective production of ethylbenzene. It comprised of a reactor vessel, vapor phase ethylene feed stream, benzene and transalkylation feed stream. Especially the product stream containing ethylbenzene was used to heat the reactor vessel, which consisted of an alkylation section, an upper heat exchange section, and a bottom heat exchange section. In such a novel reactor, vapor phase benzene and liquid phase benzene were coexisted due to the heat produced by isothermal reaction between the upper heat exchange section and the bottom heat exchange section. The process was demonstrated by the thermodynamic analysis and experimental results. In fact, during the 1010 hour-life-test of gas phase ethene with gas phase-liquid phase benzene alkylation reaction, the ethene conversion was above 95%, and the ethylbenzene selectivity was above 83% （only benzene feed） and even higher than 99% （benzene plus transalkylation feed）. At the same time, the xylene content in the ethylbenzene was less than 100 ppm when the reaction was carried out under the reaction conditions of 140-185℃ of temperature, 1.6-2.1 MPa of pressure, 3.0-5.5 of benzene/ethylene mole ratio, 4-6 v% of transalkylation feed/（benzene＋transalkylation feed）, 0.19-0.27 h^-1 of ethene space velocity, and 1000 g of 3998 catalyst loaded. Thus, compared with the conventional ethylbenzene synthesis route, the transalkylation reactor could be omitted in this novel industrial process.

Studies on the Mechanism of the Direct Synthesis of Styrene form Benzene and Ethylene

The adsorption behavior and description behavior of benzene , ethylene and ethylbenzene over HZSM-5 and Co/HZSM-5 catalysts were studied by means of TPSR (Temperature programmed surface reaction) technique. TPSR results of ben- zene and ethylene co-adsorption show that the maian products are styrene , ethylben- zene, toluene, propane, and butane. In a separate experiment of ethylbenzene ad- sorption, styrene . toluene and benzene are formed due to cracking and dehydro- genation. The mechanism of styrene formation was proposed , i. e. , the reaction was carried out via. the dehydrogenation of mediate species ethylbenzene according to the results of TPSR-MS , activity testing and thermodynamic analysis.

Bio-removal of mixture of benzene,toluene,ethylbenzene,and xylenes/total petroleum hydrocarbons/trichloroethylene from contaminated water

Four pure cultures were isolated from soil samples potentially contaminated with gasoline compounds either at a construction site near a gas station in Fai Chi Kei,Macao SAR or in the northern parts of China（Beijing,and Hebei and Shandong）.The effects of different concentrations of benzene,toluene,ethylbenzene,and three isomers（ortho-,meta-,and para-） of xylene（BTEX）,total petroleum hydrocarbons（TPH）,and trichloroethylene（TCE）,when they were present in mixtures,on the bio-removal effciencies of microbial isolates were investigated,together with their interactions during the bio-removal process.When the isolates were tested for the BTEX（50-350 mg/L）/TPH（2000 mg/L） mixture,BTEoX in BTEoX/TPH mixture was shown with higher bio-removal effciencies,while BTEmX in BTEmX/TPH mixture was shown with the lowest,regardless of isolates.The TPH in BTEmX/TPH mixture,on the other hand,were generally shown with higher bio-removal effciencies compared to when TPH mixed with BTEoX and BTEpX.When these BTEX mixtures（at 350 mg/L） were present with TCE（5-50 mg/L）,the stimulatory effect of TCE toward BTEoX bio-removal was observed for BTEoX/TCE mixture,while the inhibitory effect of TCE toward BTEmX for BTEmX/TCE mixture.The bio-removal effciency for TPH was shown lower in TPH（2000 mg/L）/TCE（5-50 mg/L） mixtures compared to TPH present alone,implying the inhibitory effect of TCE toward TPH bio-removal.For the mixture of BTEX（417 mg/L）,TPH（2000 mg/L） along with TCE（5- 50 mg/L）,TCE was shown co-metabolically removed more effciently at 15 mg/L,probably utilizing BTEX and/or TPH as primary substrates.

SEB-08 Catalyst for Manufacture of Ethylbenzene from Dilute Ethylene Applied at Hainan Refining and Chemical Company

The SEB-08 catalyst for manufacture of ethylbenzene from dilute ethylene developed by the SINOPEC Shanghai Petrochemical Research Institute(SPRI) has been successfully applied on the 65 kt/a unit for manufacture of ethylbenzene from dry gas at the SINOPEC Hainan Refining and Chemical Company.

New Alkylation Route of Benzene with Ethylene Catalyzed by [bmim]Cl/FeCl_3 Ionic Liquid

Up to now the mechanism of Friedel-Crafts reactions catalyzed by ionic liquid have not been fully understood, while carbocation mechanism was assumed. It was found that the source of H+ and the route of reaction initiated the alkylation of benzene with ethylene catalyzed by [bmim]Cl/FeCl3 ionic liquid. The fact that dewatered ionic liquids have catalytic activity for the alkylation of benzene with ethylene suggests that there exists a new catalytic route. The distinctly Bronsted acid properties of 2-H in [bmim]Cl were found through FT-IR and HNMR analysis of [bmim]Cl after titration with water free KOH in alcohol solution. In addition, the chemical shifts of proton on the [bmim]Cl ring, especially 2-H, are sensitive to the change of FeCl3 content and shifted downfield when FeCl3 was added into [bmim]Cl to form ionic liquid. Thus 2-H was easy to be disengaged from imidazolium ring with formation of H+ to initiate the reaction. The isotope-substituted method was employed to prove this mechanism, through the GC-MS analysis of alkylation products of deuterated benzene with ethylene. The route of alkylation catalyzed by FeCl3 ionic liquid was found to follow the carbocation mechanism, the resource of H+ was presented and proved using HNMR analysis of ionic liquid to inspect the intensity change of 2-H. It was found that the intensity of 2-H reduced 23% after reaction showing that the H+ arising from alkylation reaction was supplied by 2-H on the imidazole ring.

Reaction Kinetics of Ozonation of Trichloroethylene and Benzene in Gas and Liquid Phases

The kinetics of ozonation reactions of trichloroethylene (TCE) and benzene in gas and liquid phases at 101.3 kPa and 298 K was investigated in this paper. The ozonation of TCE is first order with respect to the ozone concentration and one and half order to TCE in the gas phase with the average rate constant 57.30 (mol·L^-1 )^-l.5·s^-1,and the TCE ozonation in aqueous medium is first order with respect to both ozone and trichloroethylene with the average rate constant 6.30 (mol·L^-1)-l·s^-1. The ozonation of benzene in the gas phase is first order in ozone but independent of the benzene concentration with the average reaction rate constant 0.0011s^-1. The overall kinetics of reaction between ozone and benzene in aqueous solution is found to be first order with one-half order in both ozone and bezene, with the average reaction rate constant 2.67s^-1. It is found that the ozonation rate of pallutants is much quicker than that of self-decomposition of ozone in both gas and aqueous phase.

Unraveling the incompatibility mechanism of ethylene carbonate-based electrolytes in sodium metal anodes

Ethylene carbonate(EC)is widely used in lithium-ion batteries due to its optimal overall performance with satisfactory conductivity,relatively stable solid electrolyte interphase(SEI),and wide electrochemical window.EC is also the most widely used electrolyte solvent in sodium ion batteries.However,compared to lithium metal,sodium metal(Na)shows higher activity and reacts violently with EC-based electrolyte(NaPF_(6)as solute),which leads to the failure of sodium metal batteries(SMBs).Herein,we reveal the electrochemical instability mechanism of EC on sodium metal battery,and find that the com-bination of EC and NaPF_(6) is electrically reduced in sodium metal anode during charging,resulting in the reduction of the first coulombic efficiency,and the continuous consumption of electrolyte leads to the cell failure.To address the above issues,an additive modified linear carbonate-based electrolyte is provided as a substitute for EC based electrolytes.Specifically,ethyl methyl carbonate(EMC)and dimethyl carbon-ate(DMC)as solvents and fluoroethylene carbonate(FEC)as SEI-forming additive have been identified as the optimal solvent for NaFP_(6)based electrolyte and used in Na_(4)Fe_(3)(PO_(4))_(2)(P_(2)O_(7))/Na batteries.The batter-ies exhibit excellent capacity retention rate of about 80%over 1000 cycles at a cut-off voltage of 4.3 V.

Synthesis of Branched Polyethylene via Bulky α-Diimine Nickel(II)-Catalyzed Ethylene Chain-Walking Polymerization

The catalysis of olefin polymerization through the chain-walking process is a subject of great interest. In this contribution, the successful synthesis of a Brookhart-type unsymmetrical α-diimine nickel catalyst Ni, which contains both dibenzhydryl and phenyl groups, was determined by X-ray crystallography. The compound has a pseudo-tetrahedral geometry at the Ni center, showing pseudo-C2-symmetry. Upon activation with modified methylaluminoxane (MMAO), Ni1 exhibits high catalytic activity up to 1.02 × 107 g PE (mol Ni h)−1 toward ethylene polymerization, enabling the synthesis of high molecular weight branched polyethylene. The molecular weights and branching densities could be tuned over a very wide range. The polymerization results indicated the possibility of precise microstructure control, depending on the polymerization temperature. The branching densities were decreased with increasing the polymerization temperature.

Measurements of the Critical Temperature and Pressure of Ethylene+Benzene+Ethylbenzene Mixture

Critical temperature (Tc) and critical pressure (pc) of the ternary mixture of ethylene+benzene+ethylbenzene (the mole ratio of ethylbenzene to benzene was fixed at 0.95:0.05) were measured by using a high=pressure view cell with direct visual observation.The interaction coefficients obtained from the critical properties of the relevant binary systems were used to predict the critical properties (Tc,pc) of the ternary mixture.The agreement between the prediction and experiments is satisfactory.

Reaction pathways and selectivity in the chemo-catalytic conversion of cellulose and its derivatives to ethylene glycol:A review

Biomass-to-ethylene glycol is an effective means to achieve high-value utilisation of cellulose but is hindered by low conversion efficiency and poor catalyst activity and stability.Glucose and cellobiose are derivatives of cellulose conversion to ethylene glycol,and it is found that studying the reaction process of both can help to understand the reaction mechanism of cellulose.It is desirable to develop a reusable,highly active catalyst to convert cellulose into ethylene glycol.This ideal catalyst might have one or more active sites described the conversion steps above.Here,we discuss the catalyst development of celluloseto-ethylene glycol,including tungsten,tin,lanthanide,and other transition metal catalysts,and special attention is given to the reaction mechanism and kinetics for preparing ethylene glycol from cellulose,and the economic advantages of biomass-to-ethylene glycol are briefly introduced.The insights given in this review will facilitate further development of efficient catalysts,for addressing the global energy crisis and climate change related to the use of fossil fuels.

B-COPNA resin formation from ethylene tar light fractions:Process development and mechanical exploration by molecular simulation

An efficient utilization strategy of ethylene tar(ET),the main by-product of the ethylene cracking unit,is urgently required to meet demands for modern petrochemical industry.On the other hand,condensed polynuclear aromatic resin of moderate condensation degree(B-COPNA)is a widely used carbon material due to its superb processability,the production of which is,however,seriously limited by the high cost of raw materials.Under such context,an interesting strategy was proposed in this study for producing B-COPNA resin using crosslinked light fractions of ethylene tar(ETLF,boiling point<260℃)facilitated by molecular simulation.1,4-Benzenedimethanol(PXG)was first selected as the crosslinking agent according to the findings of molecular simulation.The effects of operating conditions,including reactions temperature,crosslinking agent,and catalyst content on the softening point and yield of B-COPNA resin products were then investigated to optimize the process.The reaction mechanism of resin production was studied by analyzing the molecular structure and transition state of ETLF and crosslinking agents.It was shown that PXG exhibited a superior capacity of withdrawing electrons and a higher electrophilic reactivity than other crosslinking agents.In addition to the highest yield and greatest heat properties,PXG-prepared resin contained the most condensed aromatics.The corresponding optimized conditions of resin preparation were 180℃,1:1.9(PXG:ETLF),and 3%(mass)of catalyst content with a resin yield of 78.57%.It was the electrophilic substitution reaction that occurred between the ETLF and crosslinking agent molecules that were responsible for the resin formation,according to the experimental characterization and molecular simulation.Hence,it was confirmed that the proposed strategy and demonstrated process can achieve a clean and high value-added utilization of ETLF via B-COPNA resin preparation,bringing huge economic value to the current petrochemical industry.

Boosting kinetic separation of ethylene and ethane on microporous materials via crystal size control

The adsorptive separation of C_(2)H_(4)and C_(2)H_(6),as an alternative to distillation units consuming high energy,is a promising yet challenging research.The great similarity in the molecular size of C_(2)H_(4)and C_(2)H_(6)brings challenges to the regulation of adsorbents to realize efficient dynamic separation.Herein,we reported the enhancement of the kinetic separation of C_(2)H_(4)/C_(2)H_(6)by controlling the crystal size of ZnAtzPO_(4)(Atz=3-amino-1,2,4-triazole)to amplify the diffusion difference of C_(2)H_(4)and C_(2)H_(6).Through adjusting the synthesis temperature,reactant concentration,and ligands/metal ions molar ratio,ZnAtzPO4 crystals with different sizes were obtained.Both single-component kinetic adsorption tests and binary-component dynamic breakthrough experiments confirmed the enhancement of the dynamic separation of C_(2)H_(4)/C_(2)H_(6)with the increase in the crystal size of ZnAtzPO_(4).The separation selectivity of C_(2)H_(4)/C_(2)H_(6)increased from 1.3 to 98.5 with the increase in the crystal size of ZnAtzPO_(4).This work demonstrated the role of morphology and size control of adsorbent crystals in the improvement of the C_(2)H_(4)/C_(2)H_(6)kinetic separation performance.

Ca_(2)MnO_(4)-layered perovskite modified by NaNO_(3)for chemical-looping oxidative dehydrogenation of ethane to ethylene

Chemical-looping oxidative dehydrogenation(CL-ODH)is a process designed for the conversion of alkanes into olefins through cyclic redox reactions,eliminating the need for gaseous O_(2).In this work,we investigated the use of Ca_(2)MnO_(4)-layered perovskites modified with NaNO_(3) dopants,serving as redox catalysts(also known as oxygen carriers),for the CL-ODH of ethane within a temperature range of 700-780℃.Our findings revealed that the incorporation of NaNO_(3) as a modifier significantly-nhanced the selectivity for-thylene generation from Ca_(2)MnO_(4).At 750℃and a gas hourly space velocity of 1300 h^(-1),we achieved an-thane conversion up to 68.17%,accompanied by a corresponding-thylene yield of 57.39%.X-ray photoelectron spectroscopy analysis unveiled that the doping NaNO_(3) onto Ca_(2)MnO_(4) not only played a role in reducing the oxidation state of Mn ions but also increased the lattice oxygen content of the redox catalyst.Furthermore,formation of NaNO_(3) shell on the surface of Ca_(2)MnO_(4) led to a reduction in the concentration of manganese sites and modulated the oxygen-releasing behavior in a step-wise manner.This modulation contributed significantly to the enhanced selectivity for ethylene of the NaNO_(3)-doped Ca_(2)MnO_(4) catalyst.These findings provide compelling evidence for the potential of Ca_(2)MnO_(4)-layered perovskites as promising redox catalysts in the context of CL-ODH reactions.

Novel sandwich structured glass fiber Cloth/Poly(ethylene oxide)-MXene composite electrolyte

Recently,poly(ethylene oxide)(PEO)-based solid polymer electrolytes have been attracting great attention,and efforts are currently underway to develop PEO-based composite electrolytes for next generation high performance all-solid-state lithium metal batteries.In this article,a novel sandwich structured solid-state PEO composite electrolyte is developed for high performance all-solid-state lithium metal batteries.The PEO-based composite electrolyte is fabricated by hot-pressing PEO,LiTFSI and Ti_(3)C_(2)T_(x) MXene nanosheets into glass fiber cloth(GFC).The as-prepared GFC@PEO-MXene electrolyte shows high mechanical properties,good electrochemical stability,and high lithium-ion migration number,which indicates an obvious synergistic effect from the microscale GFC and the nanoscale MXene.Such as,the GFC@PEO-1 wt%MXene electrolyte shows a high tensile strength of 43.43 MPa and an impressive Young's modulus of 496 MPa,which are increased by 1205%and 6048%over those of PEO.Meanwhile,the ionic conductivity of GFC@PEO-1 wt%MXene at 60℃ reaches 5.01×10^(-2) S m^(-1),which is increased by around 200%compared with that of GFC@PEO electrolyte.In addition,the Li/Li symmetric battery based on GFC@PEO-1 wt%MXene electrolyte shows an excellent cycling stability over 800 h(0.3 mA cm^(-2),0.3 mAh cm^(-2)),which is obviously longer than that based on PEO and GFC@PEO electrolytes due to the better compatibility of GFC@PEO-1 wt%MXene electrolyte with Li anode.Furthermore,the solid-state Li/LiFePO_(4) battery with GFC@PEO-1 wt%MXene as electrolyte demonstrates a high capacity of 110.2–166.1 mAh g^(-1) in a wide temperature range of 25–60C,and an excellent capacity retention rate.The developed sandwich structured GFC@PEO-1 wt%MXene electrolyte with the excellent overall performance is promising for next generation high performance all-solid-state lithium metal batteries.

Polyvinyl Acetate and Vinyl Acetate-Ethylene Hybrid Adhesive: Synthesis, Characterization, and Properties

The goal is to develop a hybrid IPN network of polyvinyl acetate (PVAc) and ethylene-vinyl acetate (VAE). In this research work, the vinyl acetate (VAc)/ VAE hybrid emulsion and polyvinyl acetate emulsion (PVAc) were effectively synthesized. Emulsions with various characteristics have been developed by adjusting the weight ratios between the vinyl acetate monomer and the VAE component. The impacts on the mechanical, thermal, and physical properties of the films were investigated using tests for pencil hardness, tensile shear strength, pH, contact angle measurement, differential scanning calorimetry (DSC), and viscosity. When 5.0 weight percent VAE was added, the tensile shear strength in dry conditions decreased by 18.75% after a 24-hour bonding period, the heat resistance decreased by 26.29% (as per WATT 91) and the tensile shear strength decreased by approximately 36.52% in wet conditions (per EN 204). The pristine sample’s results were also confirmed by the contact angle test. The interpenetrating network (IPN) formation in hybrid PVAc emulsion as primary bonds does not directly attach to PVAc and VAE chains. The addition of VAE reduced the mechanical properties (at dry conditions) and heat resistance as per WATT 91. Contact angle analysis demonstrated that PVAc adhesives containing VAE had increased water resistance when compared to conventional PVA stabilised PVAc homopolymer-based adhesives. When compared to virgin PVAc Homo, the water resistance of the PVAc emulsion polymerization was enhanced by the addition of VAE.

Alkaline earth metal-based minerals/wastes-catalyzed pyrolysis of poly(ethylene terephthalate)/poly(butylene terephthalate)for benzenes-enriched oil production

The pyrolysis of poly(ethylene terephthalate)(PET)/poly(butylene terephthalate)(PBT)catalyzed by five alkaline earth metal-based minerals/wastes,namely calcined dolomite,calcite,magnesite,calcium carbide slag(CCS),and ophicalcitum,was conducted by a pyrolyzer-gas chromatography-mass spectrometer(Py-GC-MS)with the objective of recovering benzenes-enriched oil.Compared with magnesium-based catalysts and pure CaO,the calcium-based catalysts with calcium hydroxide as the main component performed better catalytic effect,which could simultaneously promote the hydrolysis of ester products and the decarboxylation of aromatic acids after hydrolysis.For PET,the addition of solid base catalysts at 600℃promoted the complete degradation of aromatic acids and aryl esters,which accounted for 32.6%and 30.7%of the pyrolysis oil,respectively.The content of benzene in oil increased from 8.8%to 31.7%–78.8%.For PBT,the addition of solid base catalysts at 600℃completely decomposed the aromatic acids,which accounted for 67.1%of the pyrolysis oil,and the content of benzene in oil increased from 12.3%to 34.5%–81.0%.During the deoxygenation of polyester pyrolysis products,increasing temperature was more effective for the decomposition/conversion of acetone and tetrahydrofuran,while increasing the alkalinity of the reaction environment contributed to the rapid decrease in acetaldehyde and aryl ketone contents.

Preparation and Thermo-Responsive Properties of Poly(Oligo(Ethylene Glycol)Methacrylate)Copolymers with Hydroxy-Terminated Side Chain

Thermo-responsive random copolymers,poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-(ethylene glycol)methyl ether methacrylate)(P(EO_(2)-co-EO_(4/5)))and poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-ethylene glycol methacrylate(P(EO2-co-EG4/5))are synthesized via atom transfer radical polymerization(ATRP).The successful synthesis and the narrow polydispersity index(PDI)of two copolymers are indicated by 1H nuclear magnetic resonance(1H-NMR)and gel permeation chromatography(GPC)analyses.The transition behaviors of polymers in the aqueous solution are demonstrated by changes in turbidity and particle sizes.The transition behavior of P(EO2-co-EG4/5)is found to be milder than that of P(EO2-co-EO4/5).Moreover,the presence of hydrogen bonds without thermo-responsive properties established by hydroxyl groups in the end-side chain of P(EO_(2)-co-EG_(4/5))hinders the dehydration at the transition temperature(TT).Attenuated total reflection Fourier transform infrared spectrometry(ATR-FTIR)analysis along with contact angle measurements reveals that both P(EO_(2)-co-EO_(4/5))and P(EO_(2)-co-EG_(4/5))films undergo phase transitions from hydrophilicity to hydrophobicity above TT.By examining the swelling and collapse behaviors of the polymer films during phase transitions,it can be concluded that the end hydroxyl groups may establish hydrogen bonds with neighboring ether groups within the films,which remain intact throughout the phase transition process due to their strong bonding interactions.This leads to an increase in steric hindrance within swollen films thereby impeding dehydration processes and inducing hysteresis during phase transitions.

Analysis of Ethylene Glycol Degumming Process and Characterization of Hemp Fibers

To overcome the shortcomings of traditional degumming process,an efficient and environmentally friendly ethylene glycol(EG) degumming process was adopted to degum hemp fibers.The surface morphology,chemical composition,chemical structures,and mechanical properties of the fiber samples were analyzed to explore the mechanism of the degumming process.It was found that the EG degumming process could be divided into the main degumming stage(heating) and the supplementary degumming stage(insulation).The removal rates of hemicellulose and lignin in the main degumming stage were 70.56% and 60.17%,respectively.In the supplementary degumming stage,9.95% hemicellulose and 25.39% lignin were removed.It is confirmed that EG can separate hemp fibers effectively with less damage,which holds great potential for the biomass fiber separation technology.

Laminar Composite Solid Electrolyte with Poly(Ethylene Oxide)-Threaded Metal-Organic Framework Nanosheets for High-Performance All-Solid-State Lithium Battery

Developing laminar composite solid electrolyte with ultrathin thickness and continuous conduction channels in vertical direction holds great promise for all-solid-state lithium batteries.Herein,a thin,laminar solid electrolyte is synthesized by filtrating–NH 2 functionalized metal-organic framework nanosheets and then being threaded with poly(ethylene oxide)chains induced by the hydrogen-bonding interaction from–NH_(2) groups.It is demonstrated that the threaded poly(ethylene oxide)chains lock the adjacent metal-organic framework nanosheets,giving highly enhanced structural stability(Young’s modulus,1.3 GPa)to 7.5-μm-thick laminar composite solid electrolyte.Importantly,these poly(ethylene oxide)chains with stretching structure serve as continuous conduction pathways along the chains in pores.It makes the non-conduction laminar metal-organic framework electrolyte highly conductive:3.97×10^(−5) S cm^(−1) at 25℃,which is even over 25 times higher than that of pure poly(ethylene oxide)electrolyte.The assembled lithium cell,thus,acquires superior cycling stability,initial discharge capacity(148 mAh g^(−1) at 0.5 C and 60℃),and retention(94% after 150 cycles).Besides,the pore size of nanosheet is tailored(24.5–40.9˚A)to evaluate the mechanisms of chain conformation and ion transport in confined space.It shows that the confined pore only with proper size could facilitate the stretching of poly(ethylene oxide)chains,and meanwhile inhibit their disorder degree.Specifically,the pore size of 33.8˚A shows optimized confinement effect with trans-poly(ethylene oxide)and cis-poly(ethylene oxide)conformation,which offers great significance in ion conduction.Our design of poly(ethylene oxide)-threaded architecture provides a platform and paves a way to the rational design of next-generation high-performance porous electrolytes.

Attenuation of ethylene signaling increases cotton resistance to a defoliating strain of Verticillium dahliae

The severity of Verticillium wilt on cotton caused by defoliating strains of Verticillium dahliae has gradually increased and threatens production worldwide. Identification of the molecular components of leaf defoliation may increase cotton tolerance to V. dahliae. Ethylene, a major player in plant physiological processes, is often associated with senescence and defoliation of plants. We investigated the cotton–V.dahliae interaction with a focus on the role of ethylene in defoliation and defense against V. dahliae.Cotton plants inoculated with V. dahliae isolate V991, a defoliating strain, accumulated more ethylene and showed increased disease symptoms than those inoculated with a non-defoliating strain. In cotton with a transiently silenced ethylene synthesis gene(GhACOs) and signaling gene(GhEINs) during cotton–V. dahliae interaction, ethylene produced was derived from cotton and more ethylene increased cotton susceptibility and defoliation rate. Overexpression of AtCTR1, a negative regulator in ethylene signaling, in cotton reduced sensitivity to ethylene and increased plant resistance to V. dahliae.Collectively, the results indicated precise regulation of ethylene synthesis or signaling pathways improve cotton resistant to Verticillium wilt.