Advanced Treatment of Wastewater Treatment Plant Effluent by Using Biofilms on Filamentous Bamboo

[ Objective ] The study aimed at treating wastewater treatment plant （WWTP） effluent by using bio-film reactor with filamentous bamboo as bio-carrier. [ Method] With the aid of a continuous flow reactor, a bio-film reactor using filamentous bamboo as bio-carrier was used to treat WWTP effluent with low C/N ratio, and the removal effects of CODc,, TN （total nitrogen）, and NO3--N in the wastewater were analyzed.[ Result ] The average removal rates of CODcr, TN, and NO3- -N reached 47.7%, 23.6% and 34.5% when the C/N ratio of influent was around 2. In addi- tion, a stable bio-film was formed very well in the secondary effluent with low C/N ratio and hardly degradable organic pollutants. The pollutants could be removed effectively because of the excellent surface characteristics and compositions of filamentous bamboo. [ Conclusion] The research provides a new method to treat WWTP effluent with low C/N ratio.

Bioavailability of Soy Protein and Corn Zein Films

The in vivo bioavailability of soy protein isolates and corn zein film material before and after film formation by heat/ pressure was determined. The In vitro digestibility of corn zein before and after film formation was also measured. Films were produced from anhydrous protein with 30% glycerol added using a heat-press method with no use of casting solvents or cross-linking agents. Corn zein raw and film material were ground under liquid nitrogen then digested in two enzyme-acid cocktails with free amino acid analysis before and after digestion. The protein efficiency ratio and net protein ratio were determined for both zein and soy protein using a weanling Sprague-Dawley descended rat feeding study. The In vitro digestibility study indicated that the non-heat pressed corn zein was more digestible than the heat pressed zein. However, the in vivo results indicated that corn and soy protein were equally bioavailable whether they were derived from film mixture prior to or after film formation. Both corn zein and soy protein material had lower protein efficiency ratio than the control diet. Furthermore, soy protein films materials had a higher protein efficiency ratio than corn zein.

Formation of epitaxial Tl_2Ba_2Ca_2Cu_3O_(10) superconducting films by dc-magnetron sputtering and triple post-annealing method

For obtaining pure phase T12Ba2Ca2Cu3O10 （T1-2223） films with good superconducting properties, the growth technique is improved by dc magnetron sputtering and a triple post-annealing process. The triple post-annealing process comprises annealing twice in argon and once in oxygen at different temperatures. In the first low-temperature annealing phase in argon, T12Ba2CaCu2O8 （T1-2212） is obtained to effectively minimize evaporation in the next step. With the increase of temperature in the second annealing stage in argon, the previously prepared T1-2212 inter-phase is converted into T1-2223 phase. An additional annealing in oxygen is also adopted to improve the properties of T1-2223 films, each containing an optimal oxygen content value. The results of X-ray diffraction （XRD） θ-2θ scans, 09 scans and rotational φ scans show that each of the T1-2223 films has a high phase purity and an epitaxial structure. Smooth films are observed by scanning electron microscopy （SEM）. The critical temperatures Tc of the films are measured to be about 120 K and the critical current densities Jc can reach 4.0 MA/cm2 at 77 K at self field.

Transparent and anti-fogging AlPO_(4)-5 films constructed by oblique oriented nano-flake crystals

In the present work,transparent and anti-fogging AlPO_(4)-5 films were prepared on glass substrates using a novel developed process.The process entails a simple in-situ sol–gel followed by vapor phase transport.The in-situ sol–gel process was implemented by coating the precursor sols for the synthesis of AlPO4-5 on the glass substrates successively using the spin-coating method.The films and powders scribed from the films were characterized by X-Ray diffraction(XRD),Fourier transform infrared spectroscopy(FT-IR),scanning electron microscope(SEM),atomic force microscope(AFM),X-ray photoelectron spectroscopy and transmission electron microscope(TEM).The unique films were composed of oblique oriented nanoflake AlPO_(4)-5 crystals with the thickness of about 20 nm.The formation of nano-flake crystals can be ascribed to the high concentration of the precursors,resulting in the formation of a supersaturation system.The obtained films showed high antifogging performance due to the superhydrophilicity with a water contact angle of lower than 1.0°.The silicone oil contact angle was also low about 8.2°.In addition,heteroatom-substituted AlPO_(4)-5 films showing different colors can be obtained easily by simply adding transition metal ions in the phosphate acid solution during the preparation that can extend the application of the method for different coating demand.

The EVA plastic film for V-process and steel castings by V-process in China

EVA plastic film is the key material for V-process. Through decades of research, special EVA film for V-process has been produced. The film has adequate elongation; its maximum is about 800% in longitudinal direction and 750% in transversal direction. The single width of the film is 2.8 m and the double width is 5.6 m, which is the widest sheet film for V-process in China. Sheets with different thickness ranging from the thickest 0.35 mm to the thinnest 0.08 mm can meet different demands in China. The film can be used not only for V-process of iron castings, but also for the manganese steel railway frog, steel rocking support and side frame castings for train and the steel bridge box for engine truck.

Enhancing superconductivity of ultrathin YBa2Cu3O7-δ films by capping non-superconducting oxides

In this study, we have explored the ways to fabricate and optimize high-quality ultrathin YBa2 Cu3 O7-δ(YBCO) films grown on single-crystal(001) SrTiO3 substrates. Nearly atomic-flat YBCO films are obtained by pulsed laser deposition.Our result shows that the termination of SrTiO3 has only a negligible effect on the properties of YBCO. In contrast, we found that capping a non-superconducting oxide layer can generally enhance the superconductivity of YBCO. PrBa2 Cu3 O7,La2 CuO4, LaMnO3, SrTiO3, and LaAlO3 have been examined as capping layers, and the minimum thickness of superconducting YBCO with capping is ~ 2 unit cells–3 unit cells. This result might be useful in constructing good-performance YBCO-based field effect devices.

Synthesis of New Multibranch Chromophores with Strong Light-emitting in Solution and in PMMA Film

Three new chromophores with triphenylamine as molecular focal point bearing one, two, or three 4-(n-butyloxystyryl) group(s) at the periphery respectively, (named as T1, T2, and T3) have been synthesized and characterized. It is interesting to find that the fluorescence quantum yield increases from T1 (0.489), to T3 (0.535), and to T2 (0.628) in cyclohexane, meanwhile the lifetime for T3 is shorter than T1 and T2, which is an important characteristic for applications in light emitting diode. Also PMMA (polymethyl methacrylate) film doped with T3 gives stronger fluorescence than T1, and T2. Cyclic voltammetry showed that T3 exhibited lowest oxidation potential of 0.52 V vs SCE, suggesting its better hole-transport property.

Treatment of Dyes Wastewater by a New Kind of Bio - Fluid Bed

A new kind of bio-fluid bed used to treat dyes wastewater is described in detail due to its several special features,such as high removal efficiency,simple struc-ture,shock load resistance,etc.By means of analyzing the experiment data,the results show that the dye wastewater’s organic matter is removed greatly after be-ing treated by this new kind of bio-fluid bed.On the other hand,the removal efficiency of chromaticity of

MICROSTRUCTURAL CHANGE OF YSZ-SUPPORTED YBaCuO SUPPERCONDUCTING FILM BY PROTON BEAM BOMBARDMENTS

Microstructural change of YBaCuO film/YSZ substrate with and without proton irradiation has been studied by scanning electron microscope and X- ray diffraction techniques. Structural analysis has shown that conversion from tetragonal to orthorhombic phases, reduction of nonsuperconducting phase and preferential rearrangement of crystal grains are all favorable to the improvement of superconductivity in the YBaCuO film supported by YSZ substrate by proton beam bombardment.

Growth and transport features of electron-doped superconductor Pr_(1-x)LaCe_xCuO_(4-δ) thin films

Tt-phase electron-doped superconductor Pr1-xLaCexCuO4-δ（PLCCO） thin films are successfully prepared on SrTiOs （100） substrates by using the dc magnetron sputtering method. It is found that the films each have a highly oriented structure along the c-axis. For optimally doped films with x ≈ 0.10, the superconducting transition temperature Tc is 25.5 K, which is similar to that of a single crystal. The quadratic temperature dependence of the resistivity is observed when T 〉 To, which can be attributed to the two-dimensional Fermi liquid behaviour. Besides, the optimal conditions for preparing the T1-phase PLCCO thin films are also discussed in detail.

Preparation of c-Axis Oriented LiNb_(1-x) Ta_xO_3 Films on Si(111) Substrates by a Modified Sol-gel Process

In this work, we succeeded in the preparation of LiNb 1- x Ta x O 3 films on Si(111) substrates by means of sol gel process, and the usual sol gel process for the preparation of LiNbO 3 and LiTaO 3 films on Si substrates was improved by adding a 33% aqueous solution of CH 3CH 2OH to the mixed sols of LiNb(OCH 2CH 3) 6 and LiTa(OCH 2CH 3) 6 . The crystallization behavior of LiNb 1- x Ta x O 3 films on Si(111) substrates has been studied. Highly c axis oriented LiNb 1- x Ta x O 3 films have been obtained within the tantalum composition range of \{0< x <0 33\}. Some factors such as the hydrogen termination of the silicon surface, the RTP annealing process that provides the unidirectional heat flow and the preheating temperature are discussed to analyze the crystallization of the c axis oriented films.

High T_c HoBa_2Cu_3O_(7-δ) Thin Films Deposited on (100) Y_2O_3Stabilized ZrO_2 Substrates by Sputtering

Thin films of superconductors HoBa_2Cu_3O_(7-δ)(HBCO) were prepared by DC-sputtering technique. The epi-taxial growth was controlled by the ratio of the oxygen pressure and Ar pressure (O_2/Ar) , the subetrate temperature T_s and the distance of the target to subetrate. Thin films deposited under the optimum conditions (Po_2/P_(Ar)= 1:2 ; T_s=730℃) show a critical temlierature clase to 87K and a transition width less than 1K. X-raydiffraction analysis shows that the films are highiy c-axis oriented. Auger electron spectroscopy depth profilingdemonstrates Ho diffusion into the Zr(Y)O_2 subetrate owing to the Ho subetitution for Y.

IONIC CONDUCTIVITY OF POLY (β-ALKOXYCARBONYLETHYLMETHYLSILOXANE)-LiClO_4 CROSSLINKED FILMS

Poly (β-carboxyethylmethylsiloxane)-LiClO_4 and poly (β-alkoxylethylmethylsiloxane)-LiClO_4 crosslinked fllms have been prepared. The ionic conductivity of the films depends on the polymer species, concentration of lithium perchlorate, temperature and content of crosslinking agent. The effect of high polar organic solvent 1, 4-butyrolactone on the ionic conductivity and mechanical properties of poly (β-carhoxyethylmethylsiloxane )-LiClO_4 system was also investignied.

Water and nitrogen transport characteristics of single-line interference infiltration under film hole irrigation with muddy water and fertilizer

Based on the experimental data,this study investigated the effect of sand content of muddy water on water and nitrogen transport characteristics of the single-line interference infiltration under film hole irrigation with muddy water and fertilizer.The relationship between the single-line interference infiltration parameters,the sand content,the wetting front movement distances,and the sand content were all established.The model of the cumulative infiltration volume of per unit film pore area,the vertical and horizontal wetting front movement distance of the free surface,and the wetting front movement distance of the interference center with sand content and infiltration time were proposed.Reveal the law of the change of soil water content and the distribution of NO_(3)^(-)-N content based on different muddy water sand content.The results indicate that at the same infiltration time,as the muddy water sand content increases,the cumulative infiltration volume per unit pore area decreases.The infiltration index of the free infiltration and the single-line interference vary little when the sand content increases,mainly are around 0.64 and 0.58.The relationship between infiltration parameters a,b and the sand content is linear function.At the same location,the more the sand content,the smaller the wetting front movement distance in free surface and the single-line interference surface,the less the NO_(3)^(-)-N content.

Preparation of Y_(1-x)Ho_xBa_2Cu_3O_(7-δ) Superconductive Thin Films

Y_(1-x)Ho_xBa_2Cu_3O_(7-δ)(0<x<1) sinsle crystal thin films oriented with the caxis perpendicular to the sur-face were grown by DC magnetron sputtering technique. Target was pieced together with half of YBa_2Cu_3O_(7-δ)(YBCO) and half of HoBa_2Cu_3O_(7-δ)(HBCO) superconducting materials. As the distance between HBCO targetmaterial and substrate is varied , the Ho content in material is changed respectively. When the content of Ho is0. 7 (atom ratio) , the T_c>83K.

The transverse laser induced thermoelectric voltages in step flow growth (1-x)Pb(Mg_(1/3)Nb_(2/3))O_(3-x)PbTiO_3 thin films

This paper reports that the transverse laser induced thermoelectric voltages （LITV） axe observed for the first time in the step flow growth （1- x）PD（Mg1/3Nb2/3）O3-xPbTiO3 （PMN-PT, x = 0.20, 0.33, 0.50） thin films deposited on vicinal-cut strontium titanate single crystal substrates. Because lead magnesium niobate-lead titanate is a solid solution of lead magnesium niobate （PMN） and lead titanate （PT）, there are two types of signals. One is wide with a time response of a microsecond, and the other superimposed with the wide signal is narrow with a time response of a nanosecond. The transverse LITV signals depend on the ratio of PMN to PT drastically. Under the irradiation of 28-ns pulsed KrF excimer laser with the 248-nm wavelength, the largest induced voltage is observed in the 0.50Pb（Mg1/3Nb2/3）O3-0.50 PbTiO3 films. Moreover, the effects of film thickness, substrates, and tilt angles of substrates are also investigated.

PCR-DGGE技术在城市污水化学生物絮凝处理中的特点

通过PCR DGGE等分子生物学技术可以不经过常规培养直接从活性污泥和生物膜样品中提取DNA ,对 16SrDNAV3区进行PCR扩增 ,结合DGGE(变性梯度凝胶电泳 ) ,从而分析活性污泥与生物膜中微生物种群结构 .研究证实 ,活性污泥培养前后微生物种群结构发生很大的改变 .同时对 2种污水处理工艺中微生物种群结构进行了对比研究 ,对同一反应器不同位置微生物分布以及不同工况下的微生物种群结构进行了初步探讨 .测定了活性污泥中部分菌种的 16SrDNAV3区片段序列 ,通过NCBI(美国国立生物技术信息中心 )基因库比对 ,初步确定细菌的属 .结果显示 ,PCR

循环水养殖系统生物滤池细菌群落的PCR-DGGE分析

通过模拟实验对循环水养殖系统中不同初始NH4+-N浓度的生物滤池中生物膜上和水中的细菌数量及群落种类组成进行了研究。对成熟生物膜及水体样品中的异养菌、氨氧化菌、亚硝酸盐氧化菌的培养计数结果表明,随着生物滤池初始氨氮浓度增大,除异养细菌数量逐渐下降外,生物膜上的氨氧化菌和亚硝酸盐氧化菌数量呈逐渐增加趋势,且均高出水样3～4个数量级;同时对上述样品的16S rRNA基因片段的PCR扩增产物进行变性梯度凝胶电泳(DGGE)分析及其序列同源性分析的结果表明,生物膜和水中都有较高的细菌多样性,同一初始氨氮浓度的滤池中生物膜上的细菌多样性高于水中的。生物滤池中的细菌主要由拟杆菌门的黄杆菌纲和变形菌门的α-、β-、γ-变形菌纲的15种细菌组成。生物膜上的优势菌包括奥雷氏菌属、湖饲养者菌属、泥滩杆菌属、沉积杆菌属、雷辛格氏菌属、冷蛇形菌属和亚硝化单胞菌属等;水体中的优势菌则有明显差异,主要有蛋黄色杆菌属、Nautella,玫瑰杆菌属和一种硫氧化菌等。初始氨氮越高的滤池中,亚硝化单胞菌属的细菌在生物膜上所占比例越高,逐渐成为优势菌之一。实验证实,挂膜初期,提高水体中初始氨氮浓度,有利于硝化细菌的富集和固着,提高生物滤池的除氮效率。

A/DAT-IAT生物膜工艺与活性污泥法处理高含盐废水对比试验

主要研究A/DAT-IAT(前置厌氧/好氧-间歇曝气池)生物膜工艺的启动,并将该工艺处理高含盐废水的结果与活性污泥法进行比较。结果表明,在总水力停留时间(HRT)为13.5h、pH=7.5、25℃、含盐量为60g/L(以NaCl计)的条件下,A/DAT-IAT生物膜工艺的启动时间为8d,比活性污泥法缩短了10d左右。待反应器运行稳定后,A/DAT-IAT生物膜工艺对CODCr、NH4+-N、PO43--P的去除率分别为80.3%、79.0%、92.4%,反应器内微生物量为11.3g/L;A/DAT-IAT生物膜工艺与活性污泥法相比,CODCr、NH4+-N、PO43--P去除率分别提高了5.8%、11.2%、16.9%,微生物量增加了3.1g/L。

厌氧-好氧生物滤池处理城市污水试验

研究了生物滤池处理城市污水的性能特点,结果表明:厌氧-好氧生物滤池去除城市污水中的CODCr、SS和NH4+-N等具有较好的效果,当进水CODCr、SS和NH4+-N分别为23、112mg/L和56mg/L时,水力停留时间8h,曝气强度在0·5~0·6L/(m2·s)时,CODCr、SS和NH4+-N的去除率分别在90%、80%和75%以上。