Xanthan Gum—Bio-Based Raw Material for Wood Adhesive

Due to their lower environmental impact, ease of accessibility, low cost, and biodegradability, bio-renewable sources have been used extensively in the last several decades to synthesize adhesives, substituting petrochemical-based adhesive. Vegetable oils (including palm, castor, jatropha, and soybean oils), lactic acid, potato starch, and other bio-renewable sources are all excellent sources for the synthesis of adhesives that are being taken into consideration for the synthesis of “eco-friendly” adhesives. Due to their widespread use, accessibility, affordability, and biodegradability, biobased raw materials like carbohydrates used to synthesize wood and wood composite adhesive have gradually replaced petrochemical-based adhesive. Recently, xanthan gum, a naturally occurring polymer, has drawn the interest of scientists as a potentially petroleum source replacement. It possesses specific rheological characteristics, excellent water solubility, and stability to heat, and can be used as a binder, thickener, suspending agent, and stabilizer. Xanthan gum increases the adhesive strength in addition to increasing the viscosity of water-soluble adhesives. This article discusses xanthan gum as a potential substitute for traditional raw materials derived from petroleum that is used as a raw material for adhesives.

A Boron-based Adhesion Aid for Efficient Bonding of Silicone Rubber and Epoxy Resin

We improved the adhesion between silicon based insulating materials and epoxy resin composites by adding the adhesion promoter cycloborosiloxane(BSi,cyclo-1,3,3,5,7,7-hexaphenyl-1,5-diboro-3,7-disiloxane).The experimental results show that the addition of BSi in the silicone rubber(SR)system significantly increases the tensile shear strength between BSi and epoxy resin(EP),reaching 309%of the original value.On this basis,the mechanism of BSi to enhance the adhesion effect was discussed.The electron deficient B in BSi attracted the electron rich N and O in EP to enhance the chemical interaction,combined with the interfacial migration behavior in the curing process,to improve the adhesion strength.This study provides the design and synthesis ideas of adhesive aids,and a reference for further exploring the interface mechanism of epoxy resin matrix composites.

Adhesive Bonding and Self-Curing Characteristics of α-Starch Based Composite Binder for Green Sand Mould/Core

Interactions between different components in α-starch based composite binder for green sand mould/core were investigated by using XRD, IR spectra, 1H NMR spectra and SEM. Several adhesive hardening structures and theories of the binder at room temperature were proposed according to the interactions between various compositions. Thus, the reasons for the binder to have excellent combination properties and unique adhesive bonding and self-curing characteristics were explained by these theories successfully. And the theories are of great directive importance to design and development of composite binder for green sand mould/core.

Recycled, Bio-Based, and Blended Composite Materials for 3D Printing Filament: Pros and Cons—A Review

In recent years, additive manufacturing (AM), known as “3D printing”, has experienced exceptional growth thanks to the development of mechatronics and materials science. Fused filament deposition (FDM) manufacturing is the most widely used technique in the field of AM, due to low operating and material costs. However, the materials commonly used for this technology are virgin thermoplastics. It is worth noting a considerable amount of waste exists due to failed print and disposable prototypes. In this regard, using green and sustainable materials is essential to limit the impact on the environment. The recycled, bio-based, and blended recycled materials are therefore a potential approach for 3D printing. In contrast, the lack of understanding of the mechanism of interlayer adhesion and the degradation of materials for FDM printing has posed a major challenge for these green materials. This paper provides an overview of the FDM technique and material requirements for 3D printing filaments. The main objective is to highlight the advantages and disadvantages of using recycled, bio-based, and blended materials based on thermoplastics for 3D printing filaments. In this work, solutions to improve the mechanical properties of 3D printing parts before, during, and after the printing process are pointed out. This paper provides an overview on choosing which materials and solutions depend on the specific application purposes. Moreover, research gaps and opportunities are mentioned in the discussion and conclusions sections of this study.

Starch-Based Adhesives for Wood/Wood Composite Bonding: Review

Increasing global energy crisis and scarcity of petroleum resources has shifted focus of chemical industries to look for alternative raw material resources. The main focus of raw materials in wood adhesives, such as petroleum and natural gas [1] [2], would be gradually replaced by renewable biopolymers. Starch is a relatively inexpensive and renewable product from abundant plants, easy processing and it has been extensively used as binders, sizing materials, glues and pastes [3], but its bonding capacity is not strong enough to glue wood [4]. Extensive research has been carried out on improving the cohesive properties, especially water resistance, of starch-based adhesives. In starch-based wood adhesive many new approaches have come forward for effective use it in wood/wood composite adhesive giving comparable performance as synthetic adhesives. This review of starch-based adhesives is made with the focus on starch modification methods for improving properties of starch-based adhesives.

State of Research and Trends in the Development of Polyvinyl Acetate-Based Wood Adhesive

Synthetic wood adhesives, consisting of urea-formaldehyde resins (UF), phenol-formaldehyde resins (PF), melamine-formaldehyde resins (MF), and polyurethane resins, are widely used. For UF and MF, most investigations are concerned with reducing free formaldehyde content;for PF, most studies focused on finding new alternative chemicals to replace phenol. These adhesives come under the Carcinogenic, Mutagenic, and Reprotoxic chemicals (CMR) category. Due to global energy issues and dependency on petroleum sources, the focus has shifted to look for alternative and renewable raw material sources for wood adhesives. Conventionally available wood adhesives are polyvinyl alcohol (PVA) stabilized, with drawbacks like poor water resistance, poor heat resistance, low-temperature workability, and it’s based on petroleum resources. Polyvinyl acetate (PVAc) is non-resistant to moisture polymer, and if such adhesive joints are exploited in a moist environment, its strength substantially decreases. Sufficiently moisture-resistant adhesive joints are obtained by modifying PVAc dispersion with special compounds like reactive comonomer, Silanes, and modified PVA. To improve the workability at low temperature, Vinyl acetate (VAc) is copolymerized with specific comonomers like butyl acetate without affecting the performance properties. Here, we aim to present an overview of the research trend of PVAc-based adhesives in the wood industry. The review summarizes the current state of research PVAc-based adhesives.

Bio-Renewable Sources for Synthesis of Eco-Friendly Polyurethane Adhesives—Review

Bio-renewable sources used during manufacturing of polyurethane (PU) adhesives have been used extensively from last few decades and replaced petrochemical based PU adhesive due to their lower environmental impact, easy availability, low cost and biodegradability. Bio-renewable sources, such as vegetable oils (like palm oil, castor oil, jatropha oil, soybean oil), lactic acid, potato starch and other bio-renewable sources, constitute a rich source for the synthesis of polyols which are being considered for the production of “eco-friendly” PU adhesives. Various bio-renewable sources for synthesis of bio-based PU adhesives and their potential applications are discussed in this review. This paper will focus on the progress of research in bio-based materials for adhesive application.

Effects of bamboo charcoal-based bio-fertilizer on wine bamboo sap yield and nutrient composition

To explore fertilization methods for wine bamboo cultivation in southwestern semi-arid areas of China, this study analyzed annual changes in sap yield and nutrient composition from May 2013 to March 2015 by using bamboo charcoal-based bio-fertilizer （ZT） and organic fertilizer treatments （CK）. The study also provided basic data for functional beverage preparation and for application of ZT. The results of the two experimental cycles revealed that under the ZT treatment, sap was available for collection from May, the beginning of the rainy season, to November, the beginning of the dry season. The period of abundance was July to October with the highest yield of sap of 3.18 L stalk-1 in September, 2014, still lower than the moso bamboo sap, which was likely due to the scale of sap production of monopodial bamboos being different from that of sympodial bamboos. In January, trace amounts of sap were still detected, suggesting that the effect of the treatment was significant. Moreover,in the dry season, soil water content and soil temperatures at 10-15 cm depths indicated that the fertilizer had the ability to maintain soil temperatures and moisture. In both fertilizer treatments, the correlation between the collected sap and environmental parameters was significant. In the ZT treatment for the entire 2 years, the effectual environ- mental factors were soil water at 10-15 cm, air tempera- tures, and wind speeds. The same determining factors were observed for the rainy season. In the CK treatments, the effectual environmental factors for the entire year and the rainy season were soil water at 0-5 cm and air moisture. The bamboo charcoal-based bio-fertilizer elevated the potassium, calcium, iron, manganese, copper, and total phosphorus content, simultaneously increasing the sap yield, protein and reducing sugar contents, and with a relative increase in sap pH. The wine bamboo sap con- tained 18 amino acids. Glutamic acid, alanine and proline were the most abundant. Compared to the controls, the treatment showed higher levels of all amino acids. Thus, the ZT treatment could be more beneficial to the development of root systems because the function of heat preservation and moisture retention prolong the sap collection period, increase sap yields, and elevate mineral element, conventional nutrients, and amino acid contents with evident fertilization effects and broader application prospects.

Efficient Thermal Stabilization of Polyvinyl Chloride with Tannin-Ca Complex as Bio-Based Thermal Stabilizer

The potential use of tannin-Ca complex derived from tannins as bio-based thermal stabilizer and antioxidant additive for polyvinyl chloride (PVC) was investigated in this work. For this project, Reapak B-NT/7060 was applied as reference thermal stabilizer. Variable compositions: (1, 2, and 3) part per hundred ratio (phr) of tannin-Ca complex in the presence of 10 phr Dioctyl phthalate (DOP) as plasticizer in all PVC formulations were prepared by melt mixing by internal mixer at 165°C. Tannin-Ca complex was characterized by FT-IR spectroscopy, scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX) analysis as well as by means of differential scanning calorimetry (DSC). The tannin derivative stabilization efficiency under inert atmosphere was determined by using thermogravimetric analysis (TGA). In addition, its thermal stabilization effect has been assessed in air as oxidizing atmosphere by DSC in dynamic conditions. According to TGA thermograms, the initial degradation temperature (Ti) and optimum degradation temperature (Top?) for the main degradation stage of PVC stabilized with this derivative were about 280°C and 310°C, respectively. While these were about 255°C and 293°C, respectively for PVC stabilized with commercial thermal stabilizer. Global results of TGA, DSC, SEM and EDX show that the tannin-Ca complex provides the best properties and results in stabilizing both against thermal degradation and thermal oxidation degradation of PVC.

Mechanical Properties of Bio-Based Epoxy Composites Reinforced with Hybrid-Interlayer Ramie and Recycled Carbon Fibres

The growing environmental concerns have led to attention on bio-based composite materials, such as the natural fibres, recycled carbon fibres and bio-based resins. Herein, the bio-based epoxy composites were reinforced with ramie fibre (RF) and recycled carbon fibre (rCF) via inter-layer hybridisation. The dynamic mechanical analysis, tensile, flexural and impact properties characterisation were conducted to analyse the mechanical behaviour of the specimens. Also, the morphology of fractured surface after mechanical tests was studied under a scanning electron microscope. When the volume ratio between RF and rCF was varied from 100/0 to 0/100, the flexural and tensile strength of composites was significantly increased, while the impact strength was reduced. Thus the maximum values of flexural strength (182 MPa) and tensile strength (165 MPa) were observed for rCF reinforced composite, whilst impact strength of 24 kJ/m2 was found for RF reinforced composite. Furthermore, the values of storage and loss modulus were increased with the rCF incorporation due to a greater degree of restriction with the addition of rCF into the matrix. The hybridisation was able to combine the specific properties of RF and rCF and optimise the mechanical performance of composites. Therefore, the alternative low-cost green composites are prepared which can replace synthetic materials for semi-structural applications.

Cell-Based Biosensors and Bio-MEMS for Its New Applications

This paper reviews a novel cell-based biosensor and Bio-MEMS which incorporate living cells as sensing elements that convert a change in immediate environment to signals conducive for processing.It is characterized with high sensitivity,excellent selectivity and fast response and have been implemented for a number of applications ranging from pharmaceutical screening to environmental pollutant detection.This paper also introduces our recent work about Light-Addressable Potentiometric Sensors (LAPS),Field Effect Transistor (FET),Micro-Electrode Array Sensors (MEAS) and Bio-MEMS for detecting the changes of concentration of extracellular ions and the action potential of living cell under effect of drugs and environmental parameters.Finely, the paper gives some prospects of cell-based biosensors in the future.

Lactic Acid-Sustainable Raw Material for Biodegradable Hot Melt Adhesive: Review

Currently, due to scarcity of hydrocarbon resources and the extensive use of water based, solvent based and hot melt adhesives in wood bonding in furniture industries and packaging industries that demand recyclability, compostability and bio-degradability, recently attention has been concentrated to making these formulations completely bio-based, sustainable and biodegradable. Biodegradable hot melt adhesives (HMAs) prepared from natural sources have a potential for use in furniture and packaging industries because of an increase in awareness of environmental issues, the replacement of conventional petroleum-derived hydrocarbon raw materials by renewable, biodegradable and sustainable materials has developed. In terms of environmental issues, such as climate crisis due to an increase of carbon dioxide emission, attempts have been made to produce HMAs using non-hydrocarbon resins, such as polylactic acid (PLA)-based resins, containing no petroleum as a raw material. Polylactic acid was prepared by self-condensation reactions of lactic acid or by lactide ring opening polymerisation, and used for packaging materials, sanitary pads, diapers etc., especially adhesives owing to its excellent processability and the excellent mechanical properties of its HMAs products. Therefore, recently the use of PLA materials as a substitute for non-biodegradable hydrocarbon-based polymers can be considered to be environmentally favourable. Here, we discussed the various uses of PLA as a sustainable and bio-degradable and sustainable hot melt adhesive.

Bio-Based Polymers for Technical Applications: A Review — Part 2

Triglyceride oil of plant seed cannot be used on its own without further modification. The fatty acids must be suitably functionalized in order to add polymerisable functionalities which will help in the curing process. The purpose of these modifications is to reach a higher level of molecular weight and cross-link density, and also to incorporate chemical functionalities known to impart stiffness in a polymer network. The modification can go through various path ways which were described in this study.

SLA-Bio处理对纯钛表面MC3T3-E1细胞黏附行为的影响

目的在传统喷砂酸蚀(SLA)处理基础上对纯钛表面进行喷砂、蚀刻和生物矿化(SLA-Bio)处理,观察其表面MC3T3-E1前成骨细胞的黏附铺展行为,以期为纯钛种植体表面改性提供更多研究方向。方法将纯钛片分为SLA组(TiO_(2)砂粒喷砂+HCI/H_(2)SO_(4)混合液酸蚀)和SLA-Bio组(SLA处理后再进行矿化处理14 d),通过SEM-EDS观察钛片表面形貌并分析其表面元素构成。于2组钛片表面接种MC3T3-E1细胞,分别于接种后1 h、6 h、24 h取出钛片,MTT法计算并比较2组钛片表面细胞黏附率,通过荧光染色观察、Image Pro Plus软件分析计算,比较不同表面MC3T3-E1细胞铺展行为及形态因子的差异。结果SLA组钛片表面呈蜂窝状、大小不一、深浅不等的不规则孔洞结构,SLA-Bio组钛片表面可见多孔微纳米球状羟磷灰石(hydroxyapatite,HA)沉积物,球体表面可见针状纳米微粒;MC3T3-E1细胞接种后1 h、6 h、24 h时,SLA-Bio组细胞黏附率均明显高于SLA组(P<0.05),SLA-Bio组细胞形态因子均明显低于SLA组(P<0.05);细胞荧光染色结果显示,与SLA组相比,SLA-Bio组在接种后各个时间段均呈现更好的黏附伸展形态。结论SLA-Bio处理可在纯钛表面形成多孔微纳米球状HA沉积物;SLA-Bio表面较SLA表面更有利于MC3T3-E1细胞的黏附和伸展,可能促进种植体骨结合的过程。

Bioinspired-Interpenetrating Network (IPNs) Hydrogel (BIOF-INPs) and TMD <i>in Vitro</i>: Bioadhesion, Drug Release and Build in Free Radical Detection and Defense

In this work, Bioactive-functionalized interpenetrating network (IPNs) hydrogel (BIOF-INPs) were prepared and investigated in vitro for the free radical detection/defense, therapeutic release as well as shear bond strength to dentine, ability to re-mineralize surface of the dentin after application of these bio-inspired materials using a biologically inspired mineralization process in vitro as well as investigating antimicrobial properties of the BIOF-INPs against S. aureous. The aim of this investigation was to evaluate the suitability and flexibility of the designer materials to act as an “in vitro” probe to gain insights into molecular origin of TMD and associated disorders.

First mushroom-shaped adhesive microstructure:A review

This letter reviews the adhesive and frictional properties of the first mushroom-shaped adhesive microstructure （MSAMS）, which has come a long way from inspiration by the attachment devices evolved in beetles to a large-scale industrial production. It was shown to have an that about twice higher pull-off force compared to a smooth control made from the same material measured on smooth substrates. Pull-off forces measured underwater are even higher than those in air. Moreover, it retained adhesive performance over thousands of attachment cycles and initial adhesive capability could be recovered by washing after being contaminated. In shearing, MSAMS exhibits reduced and stabilized friction in comparison with a smooth control, which demonstrated pronounced stick-slip motion, and shows zero pull-off force in a sheared state, allowing the adhesion to be switched on and off. The presence of a fluid in the contact zone showed adhesion enhancement on both smooth and rough substrates. All these features lead us to conclude that MSAMS may have practical potential in a variety of applications.

Adhesives for the Paper Packaging Industry: An Overview

Today, packaging plays a crucial role in maintaining the quality of products during uses by providing safeguarding against physical, chemical and environmental challenges. While polymer-based packaging material has been very extensively used, there has been a recent move to paper-based packaging products because of their economic and environmentally-friendly nature. Currently, Paper and paper-based board materials have been used as packaging material for food products, and e-commerce business. Adhesives in packaging industries are critical to the structure of most paper and paper board packaging, whether applied during the process of conversion and on the packaging line. From a production point of view, adhesive choice can significantly affect process line efficiency and production performance. Adhesive types used in paper industries are water-based adhesives both synthetic and bio-polymer based (starch, cellulose, protein and itaconic acid), Solvent-based adhesives (polyurethane and acrylic-based) and 100% solids adhesives like heat sealing adhesive and hot melts. More recently, water-based heat-expandable adhesive having thermally insulative and cushion-like properties has been provided for use in protective packages and wrap. Here, we aim to present an overview of the research trend of adhesives in the paper packaging industry. The overview summarizes the different adhesives for paper packaging industries.

A New Two Plant Tissue－based Carbon Paste Microelectrode for Neurotransmitter Detection

Presented in this paper is a biosensor constructed for the determination of neurotransmitters. It is an eggplant-banana-tissue-based carbon paste microelectrode. As oxidative enzymes in banana tissue can bio-catalytically oxidize dopamine (DA), norepinephrine(NE), L-dopa, etc, the biosensor's sensitivity is improved. Because of the ability of eggplant tissue to eliminate the oxidation of ascorbic acid (AA), the signal of AA is a steady-state response. and thereby the selectivity of the biosensor is enhanced. The effect of experimental conditions such as pH, temperature, ratio of two plant tissues, response time, and linear range were evaluated in order to optimize the analytical performance. The detection limit for DA is 3. 2 × 10-7 mol/L.Our results showed that the idea of multienzyme system is applicable to the plant tissue-based carbon paste microelectrodes.

A Review of Vegetable Oil-Based Polymers: Synthesis and Applications

The reviewed work addressed the shift in focus from conventional polymers to bio-based and renewable polymers. The environmental attributes of the renewable polymers make them preferred choice of matrix. The properties of the matrices from renewable origin could compete in high end applications. The composition of the fatty acids in plant seed oil was discussed and the determination of the level of unsaturation used the iodine value. This review also extensively discussed the values of various fatty acid components present in the oils. Areas of application of the thermosetting polymers obtained from plant seed oils were also discussed.