Starting materials, processes and characteristics of bio-based foams: A review

Biofoam products have attracted considerable attention lately because there is a growing demand for green/sustainable products.To this end,various biobased foams have either been developed or are currently in development,e.g.,bio-based polyurethanes(PUs),polylactic acid(PLA),starch,and polyhydroxyalkanotates(PHAs).Indeed,significant progress has been made;however,chal-lenges still persist,for example,biobased foam products have poor processability,inferior com-patibility,thermal and strength properties.In this review,we focus on five biofoam products:namely bio-based PUs,PLA,starch,PHAs,and cellulose biofoam products,along with their prop-erties and performance,as well as their manufacturing processes.Further efforts are still needed to unlock the full potential of these bio-based products and meet the goal of complementing and gradually replacing some of their fossil-based counterparts.Finally,the challenges,as well as arising opportunities of future research directions are discussed.

A sustainable process to 100%bio-based nylons integrated chemical and biological conversion of lignocellulose

Considerable progress has been made in recent years to the development of sustainable polymers from bio-based feedstocks.In this study,100%bio-based nylons were prepared via an integrated chemical and biological process from lignocellulose.These novel nylons were obtained by the melt polymerization of 3-propyladipic acid derived from lignin and 1,5-pentenediamine/1,4-butanediamine derived from carbohydrate sugar.Central to the concept is a three-step noble metal free catalytic chemical funnelling sequence(Raney Ni mediated reductive catalytic fractionation-reductive funnelling-oxidative funnelling),which allowed for obtaining a single component 3-propyladipic acid from lignin with high efficiency.The structural and thermodynamic properties of the obtained nylons have been systematically investigated,and thus obtained transparent bio-based nylons exhibited higher Mw(>32,000)and excellent thermal stability(Td5%>265℃).Considering their moderate Tg and good melt strength,these transparent bio-based nylons could serve as promising functional additives or temperature-responsive materials.

Aqueous-phase reforming of hydroxyacetone solution to bio-based H_(2)over supported Pt catalysts

Aqueous-phase reforming(APR)is an attractive process to produce bio-based hydrogen from waste biomass streams,during which the catalyst stability is often challenged due to the harsh reaction conditions.In this work,three Pt-based catalysts supported on C,AlO(OH),and ZrO_(2)were investigated for the APR of hydroxyacetone solution in afixed bed reactor at 225℃and 35 bar.Among them,the Pt/C catalyst showed the highest turnover frequency for H_(2)production(TOF of 8.9 molH_(2)molPt^(-1)min^(-1))and the longest catalyst stability.Over the AlO(OH)and ZrO_(2)supported Pt catalysts,the side reactions consuming H_(2),formation of coke,and Pt sintering result in a low H_(2)production and the fast catalyst deactivation.The proposed reaction pathways suggest that a promising APR catalyst should reform all oxygenates in the aqueous phase,minimize the hydrogenation of the oxygenates,maximize the WGS reaction,and inhibit the condensation and coking reactions for maximizing the hydrogen yield and a stable catalytic performance.

CO_(2)-Responsive Smart Foams Stabilized by an Extremely Rigid Bio-Based Surfactant

Environment friendly and intelligent surfactants have attracted great attention in recent years.A bio-based CO_(2)responsive surfactant rosin acid dimaleimide choline(R-BMI-C)with an extremely rigid skeleton was prepared using rosin and choline as raw materials by Diels-Alder addition reaction and acid-base neutralization reactions.Its structure was confirmed by IR and^(1)H NMR spectra.The foams’properties of R-BMI-C could be adjusted by bubbling CO_(2)/N_(2)to change the structure of the surfactant.At pH 10.4,R-BMI-C forms an unstable foam with a half-life of 1.5 h.When the pH was reduced to 7.4 by bubbling CO_(2),R-BMI-C forms an extremely stable foam with a half-life of 336 h.The surfactant R-BMI-C changed from bola type to conventional type when bubbling CO_(2).And the internal aggregation structure of R-BMI-C aqueous solution changed from spherical micelles to laminar micelles according to the cryogenic-transmission electron microscope.We know that the lamellar structure tends to adsorb at the air/water interface or is trapped in the foam film,which slows down the foam coarsening and agglomeration process,resulting in a significant increase in foam stability.R-BMI-C could be used in oil extraction,fire-fighting and chemical decontamination due to its excellent foaming,stabilization and defoaming properties.

Eco-friendly physical blowing agent mass loss of bio-based polyurethane rigid foam materials

Through systematical experiment design, the physical blowing agent(PBA) mass loss of bio-based polyurethane rigid foam(PURF)in the foaming process was measured and calculated in this study, and different eco-friendly PBA mass losses were measured quantitatively for the first time. The core of the proposed method is to add water to replace the difference, and this method has a high fault tolerance rate for different foaming forms of foams. The method was proved to be stable and reliable through the standard deviations σ1and σ2for R1(ratio of the PBA mass loss to the material total mass except the PBA) and R2(ratio of the PBA mass loss to the PBA mass in the material total mass) in parallel experiments. It can be used to measure and calculate the actual PBA mass loss in the foaming process of both bio-based and petroleumbased PURF. The results show that the PBA mass loss in PURF with different PBA systems is controlled by its initial mass content of PBA in PU materials ω. The main way for PBA to dissipate into the air is evaporation/escape along the upper surface of foam. This study further reveals the mechanism of PBA mass loss: the evaporation/escape of PBA along the upper surface of foam is a typical diffusion behavior. Its spread power comes from the difference between the chemical potential of PBA in the interface layer and that in the outside air. For a certain PURF system, R1has approximately linear relationship with the initial mass content of PBA in PU materials ω, which can be expressed by the functional relationship R1= kω, where k is a variable related to PBA’s own attributes.

Elastic Bio-based Polyurethane Nanofibrous Membrane with Robust Waterproof and Breathable Properties

Elastic bio-based waterproof and breathable membranes(EBWBMs) allow the passage of water vapor effectively and resist the penetration of liquid water,making it ideal for use under extreme conditions.In this study,we used a facile strategy to design the bio-based polyurethane(PU) nanofibrous membranes with the nanoscale porous structure to provide the membranes with high waterproof and breathable performances.The optimization of nanofibrous membrane formation was accomplished by controlling the relative ambient humidity to modulate the cooperating effects of charge dissipation and non-solvent-induced phase separation.The obtained EBWBMs showed multiple functional properties,with a hydrostatic pressure of 86.41 kPa and a water vapor transmission(WVT) rate of 10.1 kg·m^(-2)·d^(-1).After 1 000 cycles of stretching at 40% strain,the EBWBMs retained over 59% of the original maximum stress and exhibited an ideal elasticity recovery ratio of 85%.Besides,even after 80% deformation,the EBWBMs still maintained a hydrostatic pressure of 30.65 kPa and a WVT rate of 13.6 kg·m^(-2)·d^(-1),suggesting that bio-based PU nanofibrous membranes could be used for protection under extreme conditions.

Bio-Based Trivalent Phytate:A Novel Strategy for Enhancing Fire Performance of Rigid Polyurethane Foam Composites

Biomass phytic acid has potential flame retardant value as the main form of phosphorus in plant seeds.In this study,phytate-based flame retardants aluminum phytate(PA-Al)and iron phytate(PA-Fe)were synthesized and characterized.Subsequently,they were introduced into rigid polyurethane foam(RPUF)as flame retardants by one-step water-blown method.The results indicated that RPUF/PA-Fe30 exhibited the highest char residue of 22.1 wt%,significantly higher than 12.4 wt%of RPUF.Cone calorimetry analysis showed that the total heat release(THR)of RPUF/PA-Al30 decreased by 17.0%and total smoke release(TSR)decreased by 22.0%compared with pure RPUF,which were the lowest,demonstrating a low fire risk and good smoke suppression.Thermogravimetric analysis-Fourier transform infrared spectrometer(TG-FTIR)implied the release intensity of flammable gases(hydrocarbons,esters)and toxic gases(isocyanate,CO,aromatic compounds,HCN)of composites was significantly reduced after the addition of PA-Fe.The analysis of char residue indicated that the RPUF composites formed a dense char layer with a high degree of graphitization after the addition of PA-Al/PA-Fe,endowing RPUF composites with excellent mass&heat transmission inhibition effect and fire resistance in the combustion process.

Fully Bio-Based Composites of Poly(Lactic Acid)Reinforced with Cellulose-Graft-Poly-(ε-Caprolactone)Copolymers

Due to the increasing demand for modified polylactide(PLA)meeting“double green”criteria,the research on sustainable plasticizers for PLA has attracted broad attentions.This study reported an open-ring polymerization method to fabricate cellulose(MCC)-g-PCL(poly(ε-caprolactone))copolymers with a fully sustainable and biodegradable component.MCC-g-PCL copolymers were synthesized,characterized,and used as green plasticizers for the PLA toughening.The results indicated that the MCC-g-PCL derivatives play an important role in the compatibility,crystallization,and toughening of the PLA/MCC-g-PCL composites.The mechanical properties of the fully bio-based PLA/MCC-g-PCL composites were optimized by adding 15 wt%MCC-g-PCL,that is,the elongation at break was 22.6%(~376%higher than that of neat PLA),the tensile strength was 47.3 MPa(comparable to that of neat PLA),and the impact strength was 26 J/m(~130%higher than that of neat PLA).DSC results indicated that MCC-g-PCL reduced the Tg of the PLA blend.When the addition amount was 15 wt%,the Tg of the blend was 58.4°C.Compared with MCC,MCC-g-PCL polyester plasticizer has better thermal stability,T5%(°C)can still be maintained above 300°C.The rheological results showed that MCC-g-PCL acted as a plasticizer,the introduction of PCL flexible chain increased the mobility of PLA molecular chain,and decreased the complex viscosity,storage modulus and loss modulus of PLA blends.The MCC-g-PCL derivatives,as a new green plastic additive,have shown an interesting prospect to prepare fully bio-based composites.

Electrokinetic-mechanism of water and furfural oxidation on pulsed laser-interlaced Cu_(2)O and CoO on nickel foam

The electrocatalytic oxidation of biomass-derived furfural(FF)feedstocks into 2-furoic acid(FA)holds immense industrial potential in optics,cosmetics,polymers,and food.Herein,we fabricated Co O/Ni O/nickel foam(NF)and Cu_(2)O/Ni O/NF electrodes via in situ pulsed laser irradiation in liquids(PLIL)for the bifunctional electrocatalysis of oxygen evolution reaction(OER)and furfural oxidation reaction(FOR),respectively.Simultaneous oxidation of NF surface to NiO and deposition of CoO and/or Cu_(2)O on NF during PLIL offer distinct advantages for enhancing both the OER and FOR.CoO/NiO/NF electrocatalyst provides a consistently low overpotential of~359 m V(OER)at 10 m A/cm^(2),achieving the maximum FA yield(~16.37 m M)with 61.5%selectivity,79.5%carbon balance,and a remarkable Faradaic efficiency of~90.1%during 2 h of FOR at 1.43 V(vs.reversible hydrogen electrode).Mechanistic pathway via in situ electrochemical-Raman spectroscopy on CoO/NiO/NF reveals the involvement of phase transition intermediates(NiOOH and CoOOH)as surface-active centers during electrochemical oxidation.The carbonyl carbon in FF is attacked by hydroxyl groups to form unstable hydrates that subsequently undergo further oxidation to yield FA products.This method holds promise for large-scale applications,enabling simultaneous production of renewable building materials and fuel.

Layered Structural PBAT Composite Foams for Efficient Electromagnetic Interference Shielding

The utilization of eco-friendly,lightweight,high-efficiency and high-absorbing electromagnetic interference(EMI)shielding composites is imperative in light of the worldwide promotion of sustainable manufacturing.In this work,magnetic poly(butyleneadipate-coterephthalate)(PBAT)microspheres were firstly synthesized via phase separation method,then PBAT composite foams with layered structure was constructed through the supercritical carbon dioxide foaming and scraping techniques.The merits of integrating ferroferric oxideloaded multi-walled carbon nanotubes(Fe3O4@MWCNTs)nanoparticles,a microcellular framework,and a highly conductive silver layer have been judiciously orchestrated within this distinctive layered configuration.Microwaves are consumed throughout the process of“absorption-reflection-reabsorption”as much as possible,which greatly declines the secondary radiation pollution.The biodegradable PBAT composite foams achieved an EMI shielding effectiveness of up to 68 dB and an absorptivity of 77%,and authenticated favorable stabilization after the tape adhesion experiment.

Synthesis,Characterization and Water Absorption Analysis of Highly Hygroscopic Bio-based Co-polyamides 56/66

This study aims to develop highly hygroscopic bio-based co-polyamides(CPs)by melt co-polycondensation of polyamide(PA)56 salt and PA66 salt with varying molar fractions.The functional groups and the chemical structure of the prepared samples were determined by Fourier transform infrared(FTIR)spectroscopy and proton nuclear magnetic resonance(^(1)H-NMR)spectroscopy.The relative viscosity was determined with an Ubbelohde viscometer.The melting behavior and the thermal stability of CPs were investigated by differential scanning calorimetry(DSC)and thermogravimetric analysis(TGA).Furthermore,the water absorption behavior of CP hot-pressed film was studied.The results reveal that the melting point,the crystallization temperature and the crystallinity of CPs firstly decrease and then increase with the molar fraction of PA66 in CPs.The copolymerization of PA56 with PA66 leads to an obvious increase in water absorption.The CPs with PA66 molar fraction of 50%possess a high saturated water absorption rate of 17.6%,compared to 11.6%for pure PA56 and 7.8%for pure PA66.

High Water Resistance and Enhanced Mechanical Properties of Bio-Based Waterborne Polyurethane Enabled by in-situ Construction of Interpenetrating Polymer Network

In this study,acrylic acid was used as a neutralizer to prepare bio-based WPU with an interpenetrating polymer network structure by thermally induced free radical emulsion polymerization.The effects of the content of acrylic acid on the properties of the resulting waterborne polyurethane-poly(acrylic acid)(WPU-PAA)dispersion and the films were systematically investigated.The results showed that the cross-linking density of the interpenetrating network polymers was increased and the interlocking structure of the soft and hard phase dislocations in the molecular segments of the double networks was tailored with increasing the content of acrylic acid,leading to enhancement of the mechanical properties and water resistance of WPU-PAA films.Notably,with the increase in content of acrylic acid,the tensile strength,Young’s modulus,and toughness of the WPU-PAA-110 film increased by 3 times,and 8 times,and 2.4 times compared with WPU-PAA-80,respectively.The WPU-PAA-100 film showed the best water resistance,and the water absorption rate at 96 h was only 3.27%.This work provided a new design scheme for constructing bio-based WPU materials with excellent properties.

Research Status and Prospects of Bio-based Materials for Grease Barrier Coatings on Paper Food Packaging

Increased environmental and health concerns over the use of plastic packaging or fluorine-containing coatings,in combination with increased market demand for products with a longer shelf life,make bio-based materials one of the most important research candidates for alternative paper packaging materials for oil resistance.These bio-based materials have excellent oxygen and oil barriers,which are critical for food packaging.Moreover,they are biodegradable,naturally renewable,and safe.In this artical,two main groups of bio-based oil repellents for paper food packaging,including polysaccharide-based biopolymers and protein-based biopolymers,are enumerated,and the advantages and weaknesses of bio-based oil repellents are discussed,and effective solutions are proposed.Finally,research status and prospects on the development of bio-based oil-resistant coatings for the food packaging industry are presented.

Liquid injectivity in a SAG foam process:Effect of permeability

Foam is utilized in enhanced oil recovery and CO_(2) sequestration.Surfactant-alternating-gas(SAG)is a preferred approach for placing foam into reservoirs,due to it enhances gas injection and minimizes corrosion in facilities.Our previous studies with similar permeability cores show that during SAG injection,several banks occupy the area near the well where fluid exhibits distinct behaviour.However,underground reservoirs are heterogeneous,often layered.It is crucial to understand the effect of permeability on fluid behaviour and injectivity in a SAG process.In this work,coreflood experiments are conducted in cores with permeabilities ranging from 16 to 2300 mD.We observe the same sequence of banks in cores with different permeabilities.However,the speed at which banks propagate and their overall mobility can vary depending on permeability.At higher permeabilities,the gas-dissolution bank and the forced-imbibition bank progress more rapidly during liquid injection.The total mobilities of both banks decrease with permeability.By utilizing a bank-propagation model,we scale up our experimental findings and compare them to results obtained using the Peaceman equation.Our findings reveal that the liquid injectivity in a SAG foam process is misestimated by conventional simulators based on the Peaceman equation.The lower the formation permeability,the greater the error.

Propagation Properties of Shock Waves in Polyurethane Foam based on Atomistic Simulations

Porous materials are widely used in the field of protection because of their excellent energy absorption characteristics.In this work,a series of polyurethane microscopic models are established and the effect of porosity on the shock waves is studied with classical molecular dynamics simulations.Firstly,shock Hugoniot relations for different porosities are obtained,which compare well with the experimental data.The pores collapse and form local stress wave,which results in the complex multi-wave structure of the shock wave.The microstructure analysis shows that the local stress increases and the local velocity decreases gradually during the process of pore collapse to complete compaction.Finally,it leads to stress relaxation and velocity homogenization.The shock stress peaks can be fitted with two exponential functions,and the amplitude of attenuation coefficient decreases with the increase of density.Besides,the pore collapse under shock or non-shock are discussed by the entropy increase rate of the system.The energy is dissipated mainly through the multiple interactions of the waves under shock.The energy is dissipated mainly by the friction between atoms under non-shock.

An efficient and mild recycling of waste melamine formaldehyde foams by alkaline hydrolysis

Melamine formaldehyde foam(MFF)generates many poisonous chemicals through the traditional recycling methods for organic resin wastes.Herein,a high MFF degradation ratio of ca.97 wt.%was achieved under the mild conditions(160℃)in a NaOH–H2O system with ammelide and ammeline as the main degradation products.The alkaline solvent had an obvious corrosion effect for MFF,as indicated by scanning electron microscopy(SEM).The reaction process and products distribution were studied by Fourier-transform infrared spectroscopy(FTIR),X-ray photoelectron spectroscopy(XPS),and ^(13)C nuclear magnetic resonance(NMR).Besides,the MFF degradation products that have the similar chemical structures and bonding performances to those of melamine can be directly used as the raw material for synthesis of melamine urea-formaldehyde resins(MUFs).Moreover,the degradation system demonstrated here showed the high degradation efficiency after reusing for 7 times.The degradation process generated few harmful pollutants and no pre-or post-treatments were required,which proves its feasibility in the safe removal or recovery of waste MFF.

Experimental investigation of the effects of oil asphaltene content on CO_(2) foam stability in the presence of nanoparticles and sodium dodecyl sulfate

Foam stability tests were performed using sodium dodecyl sulfate(SDS)surfactant and SiO2 nanoparticles as foaming system at different asphaltene concentrations,and the half-life of CO_(2) foam was measured.The mechanism of foam stability reduction in the presence of asphaltene was analyzed by scanning electron microscope(SEM),UV adsorption spectrophotometric concentration measurement and Zeta potential measurement.When the mass ratio of synthetic oil to foam-formation suspension was 1:9 and the asphaltene mass fraction increased from 0 to 15%,the half-life of SDS-stabilized foams decreased from 751 s to 239 s,and the half-life of SDS/silica-stabilized foams decreased from 912 s to 298 s.When the mass ratio of synthetic oil to foam-formation suspension was 2:8 and the asphaltene mass fraction increased from 0 to 15%,the half-life of SDS-stabilized foams decreased from 526 s to 171 s,and the half-life of SDS/silica-stabilized foams decreased from 660 s to 205 s.In addition,due to asphaltene-SDS/silica interaction in the aqueous phase,the absolute value of Zeta potential decreases,and the surface charges of particles reduce,leading to the reduction of repulsive forces between two interfaces of thin liquid film,which in turn,damages the foam stability.

Boron nitride silicone rubber composite foam with low dielectric and high thermal conductivity

Silicone rubber(SR)is widely used in the field of electronic packaging because of its low dielectric properties.In this work,the porosity of the SR was improved,and the dielectric constant of the SR foam was reduced by adding expanded microspheres(EM).Then,the thermal conductivity of the system was improved by combining the modified boron nitride(f-BN).The results showed that after the f-BN was added,the dielectric constant and dielectric loss were much lower than those of pure SR.Micron-sized modified boron nitride(f-mBN)improved the dielectric and thermal conductivity of the SR foam better than that of nano-sized modified boron nitride(f-nBN),but f-nBN improved the volume resistivity,tensile strength,and thermal stability of the SR better than f-mBN.When the mass ratio of f-mBN and fnBN is 2:1,the thermal conductivity of the SR foam reaches the maximum value of 0.808 W·m^(-1)·K^(-1),which is 6.5 times that before the addition.The heat release rate and fire growth index are the lowest,and the improvement in flame retardancy is mainly attributed to the high thermal stability and physical barrier of f-BN.

Tamping the movement of the laser absorption cutoff position using gold foam hohlraum

In indirect-driven laser fusion experiments,the movement of the laser absorption layer will distort the radiation uniformity on the capsule.The gold foam has advantages in symmetry control and lowering wall plasma blowoff when used in an inertial confinement fusion(ICF)hohlraum.This work investigates the motion of the laser absorption cutoff position using lowdensity foam gold walls.It is found that the motion of the laser absorption cutoff position can be significantly mitigated through optimal initial low density,tailored to a specific laser shape.For a short square laser pulse,the laser absorption cutoff position remains almost stationary at an initial density of approximately 0.6 g cm^(-3).For a long-shaped laser pulse,the minimal motion of the laser absorption cutoff position is observed at an initial density of about 0.1 g cm^(-3).This approach allows for the adjustment of the symmetry of the hohlraum radiation source.The insights gained from this study serve as a crucial reference for optimizing the hohlraum wall density.

Experimental investigation on weak shock wave mitigation characteristics of flexible polyurethane foam and polyurea

In recent years,explosion shock wave has been considered as a signature injury of the current military conflicts.Although strong shock wave is lethal to the human body,weak shock wave can cause many more lasting consequences.To investigate the protection ability and characteristics of flexible materials and structures under weak shock wave loading,the blast wave produced by TNT explosive is loaded on the polyurethane foam with the density of 200.0 kg/m3(F-200)and 400.0 kg/m3(F-400),polyurea with the density of 1100.0 kg/m^(3)(P-1100)and structures composed of the two materials,which are intended for individual protection.Experimental results indicate that the shock wave is attenuated to weak pressure disturbance after interacting with the flexible materials which are not damaged.The shock wave protective capability of single-layer materials is dependent on their thickness,density and microscopic characteristics.The overpressure,maximum pressure rise rate and impulse of transmitted wave decrease exponentially with increase in sample thickness.For the same thickness,F-400 provides better protective capability than F-200 while P-1100 shows the best protective capability among the three materials.In this study,as the materials are not destroyed,F-200 with a thickness more than10.0 mm,F-400 with a thickness more than 4.0 mm,and P-1100 with a thickness more than 1.0 mm can attenuate the overpressure amplitude more than 90.0%.Further,multi-layer flexible composites are designed.Different layer layouts of designed structures and layer thickness of the single-layer materials can affect the protective performance.Within the research range,the structure in which polyurea is placed on the impact side shows the optimal shock wave protective performance,and the thicknesses of polyurea and polyurethane foam are 1.0 mm and 4.0 mm respectively.The overpressure attenuation rate reached maximum value of 93.3%and impulse attenuation capacity of this structure are better than those of single-layer polyurea and polyurethane foam with higher areal density.