Sound Transmission Loss Analysis of a Double Plate-Acoustic Cavity Coupling System with In-Plane Functionally Graded Materials

In this paper, the isogeometric analysis (IGA) is employed to develop an acoustic radiation model for a double plate-acoustic cavity coupling system, with a focus on analyzing the sound transmission loss (STL). The functionally graded (FG) plate exhibits a different material properties in-plane, and the power-law rule is adopted as the governing principle for material mixing. To validate the harmonic response and demonstrate the accuracy and convergence of the isogeometric modeling, ANASYS is utilized to compare with numerical examples. A plane wave serves as the acoustic excitation, and the Rayleigh integral is applied to discretize the radiated plate. The STL results are compared with the literature, confirming the reliability of the coupling system. Finally, the investigation is conducted to study impact of cavity depth and power-law parameter on the STL.

Transfer matrix method for free and forced vibrations of multi-level functionally graded material stepped beams with different boundary conditions

Functionally graded materials(FGMs)are a novel class of composite materials that have attracted significant attention in the field of engineering due to their unique mechanical properties.This study aims to explore the dynamic behaviors of an FGM stepped beam with different boundary conditions based on an efficient solving method.Under the assumptions of the Euler-Bernoulli beam theory,the governing differential equations of an individual FGM beam are derived with Hamilton’s principle and decoupled via the separation-of-variable approach.Then,the free and forced vibrations of the FGM stepped beam are solved with the transfer matrix method(TMM).Two models,i.e.,a three-level FGM stepped beam and a five-level FGM stepped beam,are considered,and their natural frequencies and mode shapes are presented.To demonstrate the validity of the method in this paper,the simulation results by ABAQUS are also given.On this basis,the detailed parametric analyses on the frequencies and dynamic responses of the three-level FGM stepped beam are carried out.The results show the accuracy and efficiency of the TMM.

The nonlocal solution of two parallel cracks in functionally graded materials subjected to harmonic anti-plane shear waves

In this paper, the dynamic interaction of two parallel cracks in functionally graded materials （FGMs） is investigated by means of the non-local theory. To make the analysis tractable, the shear modulus and the material density are assumed to vary exponentially with the coordinate vertical to the crack. To reduce mathematical difficulties, a one-dimensional non-local kernel is used instead of a twodimensional one for the dynamic problem to obtain stress fields near the crack tips. By use of the Fourier transform, the problem can be solved with the help of two pairs of dual integral equations, in which the unknown variables are the jumps of displacements across the crack surfaces. To solve the dual integral equations, the jumps of displacements across the crack surfaces are expanded in a series of Jacobi polynomials. Unlike the classical elasticity solutions, it is found that no stress singularity is present at the crack tips. The non-local elastic solutions yield a finite hoop stress at the crack tips. The present result provides theoretical references helpful for evaluating relevant strength and preventing material failure of FGMs with initial cracks. The magnitude of the finite stress field depends on relevant parameters, such as the crack length, the distance between two parallel cracks, the parameter describing the FGMs, the frequency of the incident waves and the lattice parameter of materials.

SCATTERING OF HARMONIC ANTI-PLANE SHEAR STRESS WAVES BY A CRACK IN FUNCTIONALLY GRADED PIEZOELECTRIC/PIEZOMAGNETIC MATERIALS

In this paper, the dynamic behavior of a permeable crack in functionally graded piezoelectric/piezomagnetic materials is investigated. To make the analysis tractable, it is assumed that the material properties vary exponentially with the coordinate parallel to the crack. By using the Fourier transform, the problem can be solved with the help of a pair of dual integral equations in which the unknown is the jump of displacements across the crack surfaces. These equations are solved to obtain the relations between the electric filed, the magnetic flux field and the dynamic stress field near the crack tips using the Schmidt method. Numerical examples are provided to show the effect of the functionally graded parameter and the circular frequency of the incident waves upon the stress, the electric displacement and the magnetic flux intensity factors of the crack.

Thermo-magnetic analysis of thick-walled spherical pressure vessels made of functionally graded materials

This study presents an analytical solution of thermal and mechanical displacements, strains, and stresses for a thick-walled rotating spherical pressure vessel made of functionally graded materials (FGMs). The pressure vessel is subject to axisymmetric mechanical and thermal loadings within a uniform magnetic field. The material properties of the FGM are considered as the power-law distribution along the thickness. Navier’s equation, which is a second-order ordinary differential equation, is derived from the mechanical equilibrium equation with the consideration of the thermal stresses and the Lorentz force resulting from the magnetic field. The distributions of the displacement, strains, and stresses are determined by the exact solution to Navier’s equation. Numerical results clarify the influence of the thermal loading, magnetic field, non-homogeneity constant, internal pressure, and angular velocity on the magneto-thermo-elastic response of the functionally graded spherical vessel. It is observed that these parameters have remarkable effects on the distributions of radial displacement, radial and circumferential strains, and radial and circumferential stresses.

3D thermally induced analysis of annular plates of functionally graded materials

Within the framework of three-dimensional elasticity theory,this paper investigates the thermal response of functionally graded annular plates in which the material can be transversely isotropic and vary along the thickness direction in an arbitrary manner.The generalized Mian and Spencer method is utilized to obtain the analytical solutions of annular plates under a through-thickness steady temperature field.The present analytical solutions are validated through comparisons against those available in open literature.A parametric study is conducted to examine the effects of gradient distribution,different temperature fields,different diameter ratio and boundary conditions on the deformation and stress fields of the plate.The results show that these factors can have obvious effects on the thermo-elastic behavior of functionally gradient materials(FGM)annular plates.

Interface microstructure and mechanical properties of selective laser melted multilayer functionally graded materials

Functionally graded material(FGM)can tailor properties of components such as wear resistance,corrosion resistance,and functionality to enhance the overall performance.The selective laser melting(SLM)additive manufacturing highlights the capability in manufacturing FGMs with a high geometrical complexity and manufacture flexibility.In this work,the 316L/CuSn10/18Ni300/CoCr four-type materials FGMs were fabricated using SLM.The microstructure and properties of the FGMs were investigated to reveal the effects of SLM processing parameters on the defects.A large number of microcracks were found at the 316L/CuSn10 interface,which initiated from the fusion boundary of 316L region and extended along the building direction.The elastic modulus and nano-hardness in the 18Ni300/CoCr fusion zone decreased significantly,less than those in the 18Ni300 region or the CoCr region.The iron and copper elements were well diffused in the 316L/CuSn10 fusion zone,while elements in the CuSn10/18Ni300 and the 18Ni300/CoCr fusion zones showed significantly gradient transitions.Compared with other regions,the width of the CuSn10/18Ni300 interface and the CuSn10 region expand significantly.The mechanisms of materials fusion and crack generation at the 316L/CuSn10 interface were discussed.In addition,FGM structures without macro-crack were built by only altering the deposition subsequence of 316L and CuSn10,which provides a guide for the additive manufacturing of FGM structures.

SCATTERING OF THE HARMONIC STRESS WAVE BY CRACKS IN FUNCTIONALLY GRADED PIEZOELECTRIC MATERIALS

The present paper considers the scattering of the time harmonic stress wave by a single crack and two collinear cracks in functionally graded piezoelectric material （FGPM）. It is assumed that the properties of the FGPM vary continuously as an exponential function. By using the Fourier transform and defining the jumps of displacements and electric potential components across the crack surface as the unknown functions, two pairs of dual integral equations are derived. To solve the dual integral equations, the jumps of the displacement and electric potential components across the crack surface are expanded in a series of Jacobi polynomials. Numerical examples are provided to show the influences of material properties on the dynamic stress and the electric displacement intensity factors.

Hybrid graded element model for transient heat conduction in functionally graded materials

This paper presents a hybrid graded element model for the transient heat conduction problem in functionally graded materials （FGMs）. First, a Laplace transform approach is used to handle the time variable. Then, a fundamental solution in Laplace space for FGMs is constructed. Next, a hybrid graded element is formulated based on the obtained fundamental solution and a frame field. As a result, the graded properties of FGMs are naturally reflected by using the fundamental solution to interpolate the intra-element field. Further, Stefest＇s algorithm is employed to convert the results in Laplace space back into the time-space domain. Finally, the performance of the proposed method is assessed by several benchmark examples. The results demonstrate well the efficiency and accuracy of the proposed method.

Optimization design and residual thermal stress analysis of PDC functionally graded materials

The distribution of thermal stresses in functionally graded polycrystalline diamond compact (PDC) and in single coating of PDC are analyzed respectively by thermo-mechanical finite element analysis (FEA). It is shown that they each have a remarkable stress concentration at the edge of the interfaces. The diamond coatings usually suffer premature failure because of spallation, distortion or defects such as cracks near the interface due to these excessive residual stresses. Results showed that the axial tensile stress in FGM coating is reduced from 840 MPa to 229 MPa compared with single coating, and that the shear stress is reduced from 671 MPa to 471 MPa. Therefore, the single coating is more prone to spallation and cracking than the FGM coating. The effects of the volume compositional distribution factor (n) and the number of the graded layers (L) on the thermal stresses in FGM coating are also discussed respectively. Modelling results showed that the optimum value of the compositional distribution factor is 1.2, and that the best number of the graded layers is 6.

Thermoelectric properties of p-type (Bi_(0.15)Sb_(0.85))_2Te_3-PbTe graded thermoelectric materials with different barriers

The p-type （Bi0.15Sb0.85）2Te3 and PbTe are typical thermoelectric materials used for low and middle temperature range and functional graded materials （FGM） is an inevitable way to widen the working temperature range. Here two segments graded thermoelectric materials （GTM） consisting of （Bi0.15Sb0.85）2Te3, PbTe and different barriers were fabricated by the common hot pressure method. Metals Fe, Mg and Ni were used as barriers between the two segments. The diffusion of different barriers between the barriers and bases were analyzed by electron microprobe analysis （EMA）. The phase and crystal structures were determined by X-ray diffraction analysis （XRD）. The thermoelectric properties were measured at 303 K along the direction parallel to the pressing direction. The results show that the compositional diffusion occurs when there is no barrier at the interface of the two segments, and the diffusion of Pb is most obvious; as the barrier material, the diffusion of metals Fe, Mg and Ni between different bases is not very obvious, and the thermoelectric properties of GTM is much better than that of the original segment.

Design of Co-sedimentation Experiments Used to Fabricate Functionally Graded Materials with a Continuous Change of Composition

In the process of particle settling in a dilute,a density graded distribution of the liquid below the suspension needs to be designed according to the gravity of the suspension prior to sedimentation.In the present paper a compositionally graded W-Mo composite was formed via the settling of the W and Mo particles,with a density gradient distributed in the initial clear liquid along the settling direction.

3D analytical solution for a rotating transversely isotropic annular plate of functionally graded materials

The analytical solution for an annular plate rotating at a constant angular velocity is derived by means of direct displacement method from the elasticity equations for axisymmetric problems of functionally graded transversely isotropic media. The displacement components are assumed as a linear combination of certain explicit functions of the radial coordinate, with seven undetermined coefficients being functions of the axial coordinate z. Seven equations governing these z-dependent functions are derived and solved by a progressive integrating scheme. The present solution can be degenerated into the solution of a rotating isotropic functionally graded annular plate. The solution also can be degenerated into that for transversely isotropic or isotropic homogeneous materials. Finally, a special case is considered and the effect of the material gradient index on the elastic field is illustrated numerically.

DYNAMIC RESPONSE FOR FUNCTIONALLY GRADED MATERIALS WITH PENNY-SHAPED CRACKS

This paper provides a method for studying the penny-shaped cracksconfiguration in functionally graded material(FGM)structuressubjected to dynamic or steady loading. It is assumed that the FGMare transversely isotropic and all the material properties onlydepend on the axial coordi- nate z. In the analysis, the elasticregion is treated as a number of layers. The material properties aretaken to be constants for each layer. By utilizing the Laplacetransform and Hankel transform tech- nique, the general solution forthe layers are derived.

COUPLED THERMAL/MECHANICAL ANALYSIS FOR THE FRACTURE OF FUNCTIONALLY GRADED MATERIALS UNDER TRANSIENT THERMAL LOADING

A comprehensive treatment of fracture of functionally gradedmaterials (FGMs) is provided. It is assumed that the materialproperties depend only on the coordinate perpendicular to the cracksurface And vary continuously along the crack faces. By using alaminated composite plate model to simulate the ma- Terialnon-homogeneity, an algorithm for solving the system based on Laplacetransform and Fourier transform Techniques is presented. Unlikeearlier studies that considered certain assumed propertydistributions and a Single crack problem, the current investigationstudies multiple crack problem in the FGMs with arbitrarily Varyingmaterial properties. Transient thermal stresses are presented.

Surface contact behavior of functionally graded thermoelectric materials indented by a conducting punch

The contact problem for thermoelectric materials with functionally graded properties is considered.The material properties,such as the electric conductivity,the thermal conductivity,the shear modulus,and the thermal expansion coefficient,vary in an exponential function.Using the Fourier transform technique,the electro-thermoelastic problems are transformed into three sets of singular integral equations which are solved numerically in terms of the unknown normal electric current density,the normal energy flux,and the contact pressure.Meanwhile,the complex homogeneous solutions of the displacement fields caused by the gradient parameters are simplified with the help of Euler’s formula.After addressing the non-linearity excited by thermoelectric effects,the particular solutions of the displacement fields can be assessed.The effects of various combinations of material gradient parameters and thermoelectric loads on the contact behaviors of thermoelectric materials are presented.The results give a deep insight into the contact damage mechanism of functionally graded thermoelectric materials(FGTEMs).

THERMAL AND THERMO-ELASTIC-PLASTIC RESPONSE OF CERAMIC-METAL FUNCTIONALLY GRADED MATERIALS—THERMAL SHOCK PROBLEM

The thermal and thermo-elastic-plastic response of newly developed ceramic-metal functionally graded materials under a thermal shock load is studied. The materials are heated at the ceramic surface with a sudden high-intensity heat flux input, and cooled at the metal surface with a flowing liquid nitrogen. Emphasis is placed on two aspects: (1) the influence of the graded composition of the materials on the temperature and stress response; and (2) the optimum design of the graded composition from a unified viewpoint of the heat insulation property and stress relaxation property. Moreover, a comparison between the thermoelastic stress and the thermo-elastic-plastic stress is also made to indicate the plasticity effect.

Frictionally excited thermoelastic dynamic instability of functionally graded materials

The perturbation method is applied to investigate the frictionally excited thermoelastic dynamic instability (TEDI) of a functionally graded material (FGM) coating in half-plane sliding against a homogeneous half-plane. We assume that the thermoelastic properties of the FGM vary exponentially with thickness. We also examine the effects of the gradient index, sliding speed, and friction coefficient on the TEDI for various material combinations. The transverse normal stress for two different coating structures is calculated. Furthermore, the frictional sliding stability of two different coating structures is analyzed. The obtained results show that use of FGM coatings can improve the TEDI of this sliding system and reduce the possibility of interfacial failure by controlling the interfacial tensile stress.

Review of functionally graded materials processed by additive manufacturing

Additive manufacturing(AM)technology makes parts through layer-by-layer deposition,which can regulate the microstructure and properties of different parts of a single part well.It provides a new idea for the preparation of functionally gradient materials(FGM),and has become a research hotspot at present.By referring to and analyzing the recent research achievements in the additive manufacturing tech-nology of FGM,the latest research progress at domestic and abroad from four aspects were summaried:selective laser melting additive man-ufacturing,electron beam additive manufacturing,arc additive manufacturing,path planning,and material texture.Moreover,the existing problems in the research are pointed out,and the future research direction and focus are prospected.

Flexural strength of zirconia/stainless steel functionally graded materials

Zirconia/stainless steel (ZrO2/SUS316L) functionally graded materials (FGMs) were fabricated by tape casting and laminating. Microstructures of FGMs were observed by optical microscope. Fracture behavior of FGMs in different loading modes and influences of different gradient changes on flexural strength were investigated. The results show that ZrO2/ SUS316L FGMs with graded components at interlayers are obtained after they are sintered in vacuum and pressureless condition at 1 350 ℃. TheⅠ?Ⅱ mixed mode crack creates in composite layer and grows to both sides zigzag while loading on ZrO2 layer. Flexural strengths are 496.4,421.7 and 387.5 MPa when gradient changes are 10%,15% and 20%,but flexural strengths of the corresponding fracture layers are 387.1,334.6 and 282.3 MPa since cracks of FGMs are affected by three-dimensional stress,respectively. The cracks are generated in ZrO2 layer and extend to SUS316L layer while loading is added on SUS316L layer,flexural strength does not change with the graded components and keeps consistent basically.