Characteristics of particulate-bound polycyclic aromatic hydrocarbons emitted from industrial grade biomass boilers

Polycyclic aromatic hydrocarbons（PAHs） are carcinogenic or mutagenic and are important toxic pollutants in the flue gas of boilers. Two industrial grade biomass boilers were selected to investigate the characteristics of particulate-bound PAHs： one biomass boiler retro-fitted from an oil boiler（BB1） and one specially designed（BB2） biomass boiler. One coal-fired boiler was also selected for comparison. By using a dilution tunnel system, particulate samples from boilers were collected and 10 PAH species were analyzed by gas chromatography–mass spectrometry（GC–MS）. The total emission factors（EFs） of PAHs ranged from 0.0064 to0.0380 mg/kg, with an average of 0.0225 mg/kg, for the biomass boiler emission samples. The total PAH EFs for the tested coal-fired boiler were 1.8 times lower than the average value of the biomass boilers. The PAH diagnostic ratios for wood pellets and straw pellets were similar.The ratio of indeno（1,2,3-cd）pyrene/[indeno（1,2,3-cd）pyrene ＋ benzo（g,h,i）perylene] for the two biomass boilers was lower than those of the reference data for other burning devices, which can probably be used as an indicator to distinguish the emission of biomass boilers from that of industrial coal-fired boilers and residential stoves. The toxic potential of the emission from wood pellet burning was higher than that from straw pellet burning, however both of them were much lower than residential stove exhausts.

Optimization Study of Active-Passive Heating System Parameters in Village Houses in the Southern Xinjiang Province

Aiming at the problems of large energy consumption and serious pollution of winter heating existing in the rural buildings in Southern Xinjiang,a combined active-passive heating system was proposed,and the simulation software was used to optimize the parameters of the system,according to the parameters obtained from the optimization,a test platform was built and winter heating test was carried out.The simulation results showed that the thickness of the air layer of 75 mm,the total area of the vent holes of 0.24 m^(2),and the thickness of the insulation layer of 120 mm were the optimal construction for the passive part;solar collector area of 28 m^(2),hot water storage tank volume of 1.4 m^(3),mass flow rate of 800 kg/h on the collector side,mass flow rate of 400 kg/h on the heat exchanger side,and output power of auxiliary heat source of 5∼9 kWwere the optimal constructions for active heating system.Test results showed that during the heating period,the system could provide sufficient heat to the room under different heating modes,and the indoor temperature reached over 18°C,which met the heating demand.The economic and environmental benefits of the system were analyzed,and the economic benefits of the systemwere better than coal-fired heating,and the CO_(2) emissionswere reduced by 3,292.25 kg compared with coalfiredheating.The results of the study showed that the combinedactive-passiveheating systemcouldeffectively solve the heating problems existing in rural buildings in Southern Xinjiang,and it also laid the theoretical foundation for the popularization of the combined heating systems.

Corrosion Behavior of TP316L of Superheater in Biomass Boiler with Simulated Atmosphere and Deposit

Corrosion behavior of TP316L was investigated with simulated atmosphere and ash deposition for the superheater in biomass boiler.Corrosion dynamic curves were plotted by mass gain.The results showed that the corrosion was dependent on temperature and was greatly accelerated by ash deposition.The mass gain was distinctly reduced in the presence of SO2 with and without ash deposition on the specimens.Corrosion rates with ash deposit at different temperatures were calculated.Two feasible methods were provided to avoid serious high-temperature corrosion in the biomass boiler.

Biomass briquette fuel,boiler types and pollutant emissions of industrial biomass boiler:A review

Biomass is considered a renewable and cleaner energy source alternative to fossil fuels.In recent years,industrial biomass boilers have been rapidly developed and widely used in the industrial field.This work makes a review on the fuel types used in industrial biomass boilers,the fuel characteristics and the characteristics of air pollutants emitted from the combustion of industrial biomass boilers and other contents in different studies.However,the existing research still has many deficiencies.In the future,further research on biomass fuel,industrial biomass boiler combustion process and the pollutants emitted by industrial biomass boiler combustion,especially the carbonaceous aerosol emitted by in-dustrial biomass boiler and carbonaceous aerosol optical properties still need to be made.At the same time,the potential harm of carbonaceous aerosols emitted from industrial biomass boiler sources to human health and climate change needs to be studied in depth.This review provides a scientific basis for the accurate evaluation of industrial biomass boilers and the effective prevention and control of various pollutants of industrial biomass boilers.

Application of a Lumped Multi-Section Model for Analyzing the Thermal Performance of a Small-Scale Biomass Boiler

The stationary lumped-cell model was developed and used to simulate the thermal characteristics of domestic biomass boiler with helically coiled tube heat exchanger(HCHE).The device serves as the heat source for ORC(Organic Rankine Cycle)unit and utilizes the thermal oil as the medium transferring the heat to the unit.Most of studies available in the literature refer to the CFD simulations for water flow in tube coils or in one-or two-turn coil elements.These investigations are basically focused on the determination of Nusselt number.The proposed herein model aims at determining the thermal performance of flue gas-oil HCHE while providing low CPU time.To demonstrate the model possibilities,it was used to predict the flue gas temperatures at the inlet and outlet from the heat exchange zone,based on measurement data regarding the outlet temperature of thermal oil.Six test series were considered.The computation results appeared to be in satisfactory agreement with experimental results(the discrepancies do not exceed 12%).The investigations showed that the used approach may be recommended as an alternative method that allows for fast prediction of thermal parameters for units of complex geometries,in particular the multi-coil heat exchangers.