Blending Fineness Ratio of Fibers for Spinning Fine Denier Fibers

The paper deals with the theoretic relationship betweenfineness of man-made fibers blended with natural fibersand regularities of the yarns made from them.Throughestablishment of the theory model and digitally analysisusing Matlab software,the optimum fineness of the fi-bers could be figured out.

Effect of Blending Ratio on the Properties of Ramie/Polyester Blended Yarn

The effects of the blending ratio on the properties of Ramie/Polyester blended yarns are discussed in this paper. The experimental results show that the elongation of the yarn with the polyester content more than 40% is better than that of others. There is a lowest tenacity of the yarn corresponding to the blending ratio of 50/50 or so. The other properties of the yarn, such as the evenness and hairiness, will be improved with the increasing of the polyester content.

ESTIMATION OF BLENDING RATIO OF TWO-COMPONENT FIBER BUNDLE FROM BUNDLE LOAD-ELONGATION CURVE

In this paper, two methods were developed to assess the blending ratio of two-componentfiber bundles. They were the peak-height method and the slope method. The relationship be-tween blending ratio and testing data was analysed, and the regression curves were obtained bystepwise regression method. It was pointed out that the testing errors of both methods were lessthan two percent. The validities of both methods were verified by experiments, All calculationsof both methods were completed by computer. The blending ratio was ascertained from the test-ing data of bundle fiber strength tester which was made by the authors themselves.

Blending Ratio Analysis of Akund / Cotton Blended Yarn Based on Micro Projection

A microscope method was developed for testing the blending ratio of akund/cotton blended yarns. Fiber characteristics such as diameter, longitudinal feature, and hollow structure were observed to identify akund and cotton. Therefore, the measurement of the blending ratio for akund/cotton blended yarns based on each fiber's amount, moisture regain, and metric count was available. The results show that using specimen's longitudinal section is more effective during the fiber counting than specimen's transverse section benefiting from the separation of the fibers.

The Hydration of Blended Cement at Low W/B Ratio

The hydration process,hydration product and hydration heat of blended cement paste mixed with mineral admixture and expansive agent at low W/B ratio are studied by XRD,thermo analysis,and calorimetry instrument,and they were compared with those of pure cement paste.The results show that pure cement and blended cement at low W/B ratio have the same types of hydration products,but their respective amounts of hydration products of various blended cements at same ages and the variation law of the amount of same hydration products with ages are different;The joint effect of tumefaction of gel-ettringite due to water absorption and the expansive pressure on the pore and rift caused by the crystalloid ettringite is the impetus of the volume expansion of cement paste,and the former effect is much greater than the latter one.

Analytical Algorithms for the Blend Ratios by Fibre-bundle Tensile Curves Part I: Typical Tensile Curve and the Strength and Work Methods

The blend ratio and tensile properties are vital important characteristics of blended fibre bundles. Fibre-bundle tensile behaviour has been measured by means of the Sirolan-Tensor in order to derive a typical specific stress — extension curve. According to the typical tensile curve, the relationships between the blend ratio and the tensile parameters are discussed and established. Two new algorithms, so-called the strength method and the work method, have been developed for the blend-ratio estimation of blended fibre bundles. The relevant blend-ratios and calculations of the two methods are defined in detail. Also, the characteristics have been explained for every calculation and compared to each others. The experimental results show that the blend ratios estimated from the theoretical methods are high coincidence with the measured results. Meanwhile, the specific stress — extension curve of blended fibre bundles depends directly on the blend ratios of the fibre bundles.

Analytical Algorithms for the Blend Ratios by Fibre-bundle Tensile Curves Part Ⅱ: Calculations of the Modulus Method and the Percentage Method

The principles for the modulus method and the percentage method are established and discussed in the part following Part Ⅰ of the series papers, in which we proposed the various algorithms of the strength method and the work method. The samples of Wool/PET blended fibre bundles, the method of fibre-bundle tensile tests and the typical specific stress-extension curves from the fibre bundles with different blend ratios are the same as in Part Ⅰ. It can be found that the theoretical results estimated by the modulus and percentage methods accord with the experimental values highly though the calculations of the two methods are slightly more complex than those of the strength and work methods. Especially, using the modulus method can not only avoid the influence of the error caused by the determination of the tensile curve of no fibre breaking in stretching, Y(e), but also need not to know the tensile curves of mono-component fibre bundles in certain calculation. The latter advantage of the modulus method exists in the percentage method too, but it should adopt the improved calculation of ones.

Investigation of the Effects of a Large Percentage of Dried Sludge on the Operation of a Coal-Fired Boiler

A 600 MW coal-fired boiler with a four-corner tangential combustion mode is considered here to study the combustion features and pollutant emissions at different loads for large-percentages of blending dried sludges.The influence of the over-fired air(OFA)coefficient is examined and the impact of the blending ratio on the boiler operation is explored.The results show that for low blending ratios,a slight increase in the blending ratio can improve the combustion of bituminite,whereas a further increase leads to the deterioration of the combustion of blended fuels and thus reduces the boiler efficiency.Enhancing the supporting capability of the secondary air effectively reduces the slagging degree in the bottom ash hopper and improves the burnout rate of coals.For a large-percentage blending case at full load,it is found that the OFA coefficient must be reduced appropriately,otherwise,a secondary high-temperature combustion zone can be generated in the vicinity of the furnace arches,causing high temperature slagging and superheater tube bursting.Considering the influences of combustion and pollutant emissions,the recommended OFA coefficient is 0.2.Blending dried sludge under low loads increases the flue gas temperature at the furnace exit.While reducing the flue gas temperature in the main combustion region,which is beneficial to the safe operation of the denitrification system.Increasing the blending ratio and reducing load lead to an increase in NOx concentration at the furnace exit Sludges with low nitrogen content are suggested for the practical operation of boilers.

Analytical Algorithms for the Blend Ratios by Fibre-bundle Tensile Curves Part Ⅲ: The Definition Method and the Relationships between the Blend Ratio and Tensile Parameters Calculated from Different Ways

The algorithms of the strength, work, modulus and percentage methods have been introduced and discussed in Part Ⅰ and Part Ⅱ of the series papers. As the following, the percentage-function calculation and the frequency-function calculation of the definition method are defined and developed in detail. Meanwhile, the procedures to find the tensile parameters are analysed experimentally and involve “ED” being the average values of the corresponding tensile parameters of each bundle tensile curve measured; “EC” being the tensile parameters obtained from the averaged experimental tensile curve; and “TC” being the parameters of the theoretical tensile curve according to the corresponding nominal blend ratio. The theoretical and experimental results indicate that the blend ratio estimated by the definition method from wool/polyester blended fibre bundles has a high correlation with the actual blend ratio though the variables to be known in this method are the most of all the methods and there exist the difficulty to solve fibre bundle tensile behaviour without fibre broken in accuracy and that there are high correlations between the EC and TC data and the tensile parameters should be calculated using the EC method rather than the ED method with the exception of the bundle initial modulus. The relationships between blend ratios and the tensile properties of blended fibre bundles can be used to select the optimum blend ratio of blended tops or yarns.

天然气管道掺氢输送研究现状与分析

天然气管道掺氢输送是实现大规模、远距离和低成本氢气运输的手段之一,但氢气掺入天然气管道给管线运行工况、安全维护等带来了不容忽视的影响,具有一定的安全隐患。为此,围绕国内外天然气管道掺氢输送的技术研究与工程应用现状,讨论了影响天然气管道掺氢安全输送的主要因素,即掺氢引起的天然气物性改变、氢致失效和掺混不均,以及掺氢管道泄漏扩散和燃爆的安全问题。结果表明,天然气掺氢后,对现有管材提出了新要求,需开展相关实验以揭示氢致失效机理,掺氢天然气管道停输后是否发生气体分层与管道是否发生氢致失效密切相关。掺氢天然气管道泄漏扩散及自燃的安全范围、发生燃爆所需的最小掺氢比及燃爆机理尚不明晰,实验研究与实际运营存在差距。针对天然气管道掺氢输送的规范、标准及相关监管政策仍处于发展阶段,需要结合系统的研究数据及实践进一步完善。以上结果明晰了掺氢输送存在的风险,可为大规模掺氢混输的工程推广与实际运营提供参考。

控释掺混肥对小麦–玉米轮作体系产量、氮肥利用效率及氨挥发的影响

【目的】针对华北平原冬小麦-夏玉米轮作体系氮肥施用量大、氮肥利用率低、氮素损失严重等问题,探讨不同配比的控释掺混肥减氮和一次性施肥对周年作物产量、氨挥发损失和施肥经济效益的影响,确立麦玉轮作体系轻简高效和环境友好的施肥技术。【方法】于2022—2023年,在山东省德州市现代农业科技园区开展田间试验。冬小麦和夏玉米均设不施氮对照(CK)、农户习惯施氮(FFP)、优化施氮(OPT)、CRBF1(包膜尿素与普通尿素在冬小麦和夏玉米上的掺混比例分别为5∶5和3∶7)和CRBF2(包膜尿素与普通尿素在冬小麦和夏玉米上的掺混比例分别为7∶3和5∶5),共5个处理。基施和追施肥后,监测了氨挥发量、强度和损失率。分析了作物干物质积累和产量、氮素吸收量和氮肥利用效率,并计算了施肥经济效益。【结果】与FFP处理相比,CRBF1和CRBF2处理的夏玉米、冬小麦和周年产量差异不显著;CRBF1和CRBF2处理夏玉米氮肥偏生产力提高了8.87~9.86 kg/kg,CRBF2处理玉米氮肥回收率提高了48.4%(P<0.05);CRBF1和CRBF2处理冬小麦季氮肥回收率、氮肥农学利用率和氮肥偏生产力分别提高了30.3%~37.2%、5.22~5.77 kg/kg和6.52~7.06 kg/kg(P<0.05)。与FFP和OPT处理相比,CRBF1和CRBF2处理的肥料+施肥人工投入减少381~960元/hm^(2),周年净收入增加1208~2654元/hm^(2)。CRBF1和CRBF2处理的周年氨挥发损失量、损失强度和损失率较FFP处理分别降低了69.7%~71.9%、72.0%~74.5%和90.0%~94.1%(P<0.05)。【结论】包膜尿素与普通尿素在冬小麦、夏玉米季按照5∶5、3∶7,或者按照7∶3、5∶5的比例掺混一次性基施,均可在减少氮肥用量和施肥劳力投入的条件下,确保周年作物产量稳定,提高生产效益,并显著降低氨挥发损失,是华北平原冬小麦-夏玉米轮作系统高产高效、轻简施肥的有效氮肥施用技术。

胶粉/SEBS-g-MA共混比对复合材料粘弹行为的影响

研究了胶粉/SEBS-g-MA共混比对胶粉/SEBS-g-MA复合材料力学性能和粘弹行为的影响。结果表明:当共混比为60/40时,复合材料的力学性能最佳;随着胶粉用量的增加,应力松弛程度增大,随着热处理温度的升高,应力松弛可逆恢复程度先减小后增大;Mullins效应随着温度的升高逐渐减弱。

集输系统双管掺水工艺节能优化运行研究

某区块采用双管掺水集油工艺流程,由于现场无法判断掺水参数与现场工况的关系,导致回液温度远高于原油凝点,造成能源浪费,超出了经济运行成本区间。针对上述问题,利用Pipesim软件实现工艺建模,分析了掺水参数与工艺热能损失、井口回压、回液温度、工艺压能损失及能耗损失占比等参数的定量关系,得到了符合现场调控的一般性规律,并通过建立目标函数和约束条件,利用萤火虫算法实现了掺水比和掺水温度的自动调控。结果表明:掺水温度建议不超过75℃,掺水比不宜过高,现场调控应采用先调节掺水温度再调节掺水比的操作方式;随着掺水比和掺水温度的增加,单井运行费用存在最低值;经算法优化后,不同单井掺水比和掺水温度均有不同程度下降,预计每天可节约运行费用0.5万元~1万元。

静置工况条件下掺氢天然气浓度分布规律

利用天然气管道进行掺氢输送已成为氢能及天然气输送领域的热点和重点,但当前业界对于掺氢天然气在管道输送和停输静置过程中是否会自发分层一直存在较大争议。为了厘清该问题,以掺氢天然气在管道中静置这一极端工况为例,基于热力学能量最小原理,推导了在重力场作用下掺氢天然气浓度分布数学模型,并采用Peng-Robinson真实气体状态方程对该数学模型进行了求解,最后研究了甲烷—氢气二元组分混合气体在4种典型场景高度和5种掺氢比下氢浓度随高度的分布规律。研究结果表明:(1)在重力影响下管道顶部和底部的氢浓度存在差异,但其受高度差的影响显著,对于米级的水平管道、几十米级的一般城镇楼宇天然气立管、百米级的高层楼宇天然气立管,氢浓度随高度变化的差异微小,可完全忽略氢分层;(2)对于千米级大落差的掺氢天然气管道,当掺氢比不超过20%时,氢分层仍可忽略,但当掺氢比很高时(例如50%)管道顶部和底部的氢浓度差将超过1%,此时需考虑工程实际情况评估能否忽略氢分层;(3)西气东输某管道考虑真实气体组成、掺氢比20%、管道落差200 m时,各气体组分的浓度随落差高度的分布规律揭示了在实际工程中此类落差高度的掺氢天然气氢分层可忽略。结论认为,对于掺混均匀的掺氢天然气在静置这种最容易发生分层的极端工况下,如果不存在千米级极端大落差和极端大掺氢比,掺氢天然气管道分层现象可完全忽略;该认识从理论上厘清了目前关于掺氢天然气分层现象的争议,对掺氢天然气管道安全输送具有重要指导意义。

阻燃纤维/不锈钢纤维混纺纱线的力学性能分析

为探讨混纺比对纱线性能的影响,测试分析了5种不同混纺比的阻燃腈纶(A)/阻燃黏胶(R)/不锈钢纤维(G)(A90/G10、A70/R20/G10、A45/R45/G10、A20/R70/G10、R90/G10)混纺纱线的力学性能。结果表明:混纺纱线的拉伸断裂性能、弹性、蠕变性能、耐磨性能、扭转性能和弯曲性能随阻燃腈纶纤维混纺比的增加而提升;A45/R45/G10混纺纱线的疲劳性能较差,A90/G10混纺纱线的疲劳性能较好;在较大压力下,A70/R20/G10和R90/G10混纺纱线的压缩性能较好,在较小压力下,A20/R70/G10混纺纱线的压缩性能较好。

不同燃料外配比例烧结杯试验及烧结矿冶金性能试验

本文针对酒钢烧结生产中存在的问题,系统研究了不同燃料外配比例对烧结垂直烧结速度、成品率、利用系数、烧结时间、转鼓强度及烧结矿冶金性能等指标的影响。试验结果表明:随着燃料外配比例的增加,烧结利用系数呈先提高后降低的趋势,综合考虑最佳的燃料外配比例为60%;随着燃料外配比例的增加,烧结矿低温还原粉化率RDI_(+3.15mm)、烧结矿900℃还原度、烧结矿软化熔滴性能均变化不大,基本持平。

精梳工艺对混色纱纤维径向混和效果的影响

为探讨精梳工艺对涤粘混色纱纤维径向混和效果的影响,基于纤维成像法观察混纺纱横截面的纤维分布情况,建立了混纺纱横截面纤维径向混和不匀率的数学模型,采用涤粘普梳混纺工艺路线与涤粘精梳混纺工艺路线分别制备两种混纺比的涤粘混色纱,计算两种混色纱的纤维径向混和不匀率。结果表明:涤粘精梳混纺工艺能够显著提高纱线截面内的纤维径向混和均匀性;与涤粘普梳纱相比,涤/粘混纺比为65/35时,涤粘精梳混纺纱的涤纶径向混和不匀率降幅为42.88%,粘胶纤维径向混和不匀率降幅为41.91%;涤/粘混纺比为50/50时,涤粘精梳混纺纱的涤纶、粘胶纤维径向混和不匀率降幅分别为40.57%、39.55%;涤粘普梳混纺工艺对纤维混纺比的控制更加准确。

考虑碳交易机制与氢混天然气的园区综合能源系统调度策略

综合能源系统有利于实现多能互济、能源高效利用。以含电、热、冷、氢负荷的园区综合能源系统为研究对象,分析了可再生能源制氢系统及掺氢燃气轮机运行中多种能源的耦合及梯级利用特性,考虑了掺氢比对燃气轮机效率以及热电比的影响,以系统运行成本最小为目标函数,建立了阶梯式碳交易机制下的园区综合能源系统优化调度模型。采用分段线性化和大M法将包含多个0–1变量和连续变量的非线性模型转化为混合整数规划模型,并调用Cplex求解器实现快速求解。算例分析表明,所提调度策略可有效提高园区能源系统运行经济性,合理调控燃气轮机掺氢比有利于降低园区系统的碳排放。

混纺比对PLA棉混纺纱力学性能的影响

为了研究混纺比对PLA棉混纺纱力学性能的影响关系,制备了PLA含量为10%~90%的9种混纺纱以及纯PLA纱、纯棉纱,并对其力学性能进行测试。将混纺纱中各组分纤维的强伸曲线用纯PLA纱和纯棉纱的强伸曲线替代,建立混纺纱强伸性能预测模型,以提升模型预测的精准度。结果表明:试验所用PLA/棉的临界混纺比为70/30,当PLA含量低于70%时,混纺纱的断裂强度随着PLA含量的增加逐渐下降,而断裂伸长率趋于稳定;当PLA含量高于70%时,混纺纱的断裂强度和断裂伸长率都逐渐增大;混纺纱力学性能指标的实测值与模型预测值具有高度一致性,体现了预测模型的准确性。认为该预测模型为预测混纺纱力学性能提供了一种比较简便的方法。

掺氢天然气管网数值仿真轻量化算法

目前针对管网数值仿真算法的优化主要集中在代数方程组的求解上。针对管网流动数值仿真算法提升计算效率方案中缺少针对封闭关系与状态方程的优化,分析了目前优化方案各模块的耗时情况,发现了仿真程序中耗时模块为封闭关系与状态方程求解。最后,结合计算机库函数的缺点以及现代CPU中SIMD (Single Instruction Multiple Data)模型的特点,提出了针对封闭关系与状态方程的轻量化算法,并验证了算法的高效性。研究结果表明:(1)封闭关系与状态方程模型中的耗时原因为直接调用库函数的次幂运算、指数运算、对数运算以及除法运算;(2)由于次幂运算效率远低于其他运算,通过变换消除了模型中几乎所有的次幂运算;(3)利用SIMD指令来计算指数运算与对数运算,实现了在单核CPU上同时计算多个数据的指数与对数,最后通过数学变换将所有除法转换为乘法;(4)轻量化算法加速效果显著,其整体加速比为18,而在状态方程求解模块的加速比更是高达70以上。结论认为,该轻量化算法在不影响计算精度的条件下提高了计算速度,对于提高掺氢天然气管网在线仿真与智能管网的建设具有重要的理论价值和技术支撑。